CO2 adsorption on Cr(1 1 0) and Cr2O3(0 0 0 1)/Cr(1 1 0)

We attempt to correlate qualitatively the surface structure with the chemical activity for a metal surface, Cr(1 1 0), and one of its surface oxides, Cr₂O₃(0 0 0 1)/Cr(1 1 0). The kinetics and dynamics of CO₂ adsorption have been studied by low energy electron diffraction (LEED), Aug er electron spectroscopy (AES), and thermal desorption spectroscopy (TDS), as well as adsorption probability measurements conducted for impact energies of E_i = 0.1-1.1 eV and adsorption temperatures of T_s = 92-135 K. The Cr(1 1 0) surface is characterized by a square shaped LEED pattern, contamination free Cr AES, and a single dominant TDS peak (binding energy E_d = 33.3 kJ/mol, first order pre-exponential 1 × 10¹³ s⁻¹). The oxide exhibits a hexagonal shaped LEED pattern, Cr AES with an additional O-line, and two TDS peaks (E_d = 39.5 and 30.5 kJ/mol). The initial adsorption probability, S₀, is independent of T_s for both systems and decreases exponentially from 0.69 to 0.22 for Cr(1 1 0) with increasing E_i, with S₀ smaller by ∼0.15 for the surface oxide. The coverage dependence of the adsorption probability, S(Θ), at low E_i is approx. independent of coverage (Kisliuk-shape) and increases initially at large E_i with coverage (adsorbate-assisted adsorption). CO₂ physisorbs on both systems and the adsorption is non-activated and precursor mediated. Monte Carlo simulations (MCS) have been used to parameterize the beam scattering data. The coverage dependence of E_d has been obtained by means of a Redhead analysis of the TDS curves.     

Adsorption dynamics of CO2 on Cu(1 1 0): A molecular beam study

Molecular beam scattering measurements have been conducted to examine the adsorption dynamics of CO₂ on Cu(1 1 0). The initial adsorption probability, S₀, decreases exponentially from 0.43 ± 0.03 to a value close to the detection limit (∼0.03) within the impact energy range of E_i = (0.12-1.30) eV. S₀ is independent of the adsorption temperature, T_s, and the impact angle, α_i, i.e., the adsorption is non-activated and total energy scaling is obeyed. The coverage, Θ, dependent adsorption probability, S(Θ), agrees with precursor-assisted adsorption dynamics (Kisliuk type) above T_s ∼ 91 K. However, below that temperature adsorbate-assisted adsorption (S increases with Θ) has been observed. That effect is most distinct at large E_i and low T_s. The S(Θ) data have been modeled by Monte Carlo simulations. No indications of CO₂ dissociation were obtained from Auger Electron Spectroscopy or the molecular beam scattering data.     

Molecular beam scattering of linear and branched butane on graphite (HOPG)

The adsorption of n-butane and iso-butane on HOPG (highly-oriented pyrolitic graphite) has been studied by molecular beam scattering. The initial adsorption probability, S₀, decreases with impact energy, E_i, and is independent of surface temperature, T_s, i.e., molecular adsorption is present. The adsorption probability, S, increases with coverage, Θ, which is most distinct at large E_i and low T_s. Thus, precursor mediated adsorption is concluded. Whereas S₀ of the linear alkane is larger than the one of the branched alkane, consistent with their molecular structure, the shapes of S(Θ) curves are approximately identical. The rotational excitation of the molecules appears to affect S₀ for n-butane but not for iso-butane. Monte Carlo simulations (MCS) have been conducted to extract dynamics parameters from the S(Θ) curves.     

Isomeric effects on room-temperature chemisorption and thermal evolution of iso-, cis- and trans-dichloroethylene on Si(1 1 1)7 × 7

The room-temperature adsorption and thermal evolution of iso-, cis- and trans-dichloroethylene (DCE) on Si(1 1 1)7 × 7 have been studied by vibrational electron energy loss spectroscopy and thermal desorption spectrometry (TDS). The presence of the Si-Cl stretch at 510 cm⁻¹ suggests that, upon adsorption, all three isomers dissociate via C-Cl bond breakage on the 7 × 7 surface to form mono-σ bonded chlorovinyl , which could, in the case of iso-DCE, further dechlorinate to vinylidene (:CCH₂) upon insertion into the back-bond. The higher saturation exposure for the Si-Cl stretch at 510 cm⁻¹ observed for cis- and trans-DCE than iso-DCE suggests that Cl dissociation via the CHCl group in the cis and trans isomers is less readily than the CCl₂ group in iso-DCE. Our TDS data show remarkable similarities in both molecular desorption near 360 K and thermal evolution of the respective adstructures for all three isomers on Si(1 1 1)7 × 7. In particular, upon annealing to 450 K, the mono-σ bonded chlorovinyl adspecies is found to further dechlorinate to either vinylene di-σ bonded to the Si surface or acetylene to be released from the surface. Above 580 K, vinylene could also become gaseous acetylene or undergo H abstraction to produce hydrocarbon or SiC fragments. All three DCE isomers also exhibit TDS features attributable to an etching product SiCl₂ at 800-950 K and recombinative desorption products HCl at 700-900 K and H₂ at 650-820 K. The stronger Cl-derived TDS signals and Si-Cl stretch at 510 cm⁻¹ over 450-820 K for trans-DCE than those for cis-DCE indicate stronger dechlorination for trans-DCE than cis-DCE, which could be due to less steric hindrance resulting from the formation of the chlorovinyl adspecies for trans-DCE during the initial adsorption/dechlorination process. Finally, our density functional calculations qualitatively support the thermodynamic feasibility and relative stabilities of the proposed adstructures involving chlorovinyl, vinylidene, and vinylene adspecies.     

Formation of vinylidene and vinylene by selective reactivity of Si(1 0 0)2 × 1 towards iso, cis and trans isomers of dichloroethylene

The room temperature (RT) chemisorption of three (iso, cis and trans) isomers of dichloroethylene (DCE) on Si(1 0 0)2 × 1 have been investigated by X-ray photoelectron spectroscopy (XPS) and temperature programmed desorption (TPD). Unlike ethylene, the lack of molecular desorption features in the TPD data effectively rules out the cycloaddition adsorption mechanism for all three isomers. XPS spectra show that cis- and trans-DCE adsorb dissociatively on the 2 × 1 surface in equal proportion as mono-σ bonded 2-chlorovinyl and di-σ bonded vinylene adspecies, which could be produced by dechlorination mechanisms involving the proposed tri-atom π-complex and diradical intermediates, respectively. Acetylene (m/z 26) evolution from 2-chlorovinyl adspecies at 590 K and vinylene at 750 K are also observed for both cis- and trans-DCE, further confirming the common adsorption mechanisms for these geometrical isomers and the relative stabilities of the adspecies. In contrast, only vinylidene adspecies is found for iso-DCE, which indicates that the high ionicity of the CCl₂ group favours the diradical dechlorination mechanism. The single m/z 26 desorption peak for iso-DCE adspecies observed at a higher temperature (780 K) than cis and trans isomers is consistent with the higher adsorption energy of vinylidene than vinylene on Si(1 0 0) obtained in our ab initio calculations. The different relative locations of the Cl atoms in these isomers therefore play a crucial role in controlling the adsorption and thermal evolution on Si(1 0 0)2 × 1. The selective reactivity of the 2 × 1 surface towards these isomers can be used to generate vinylene or vinylidene templates from their corresponding adspecies.     

Carbon monoxide adsorption on the metastable fcc-Co/Cu(1 0 0) surface

The adsorption properties of CO on the epitaxial five-monolayer Co/Cu(1 0 0) system, where the Co overlayer has stabilized in the metastable fcc-phase, are reported. This system is known to exhibit metallic quantum well (MQW) states at energies 1 eV or greater above the Fermi level, which may influence CO adsorption. The CO/fcc-Co/Cu(1 0 0) system was explored with low energy electron diffraction (LEED), inverse photoemission (IPE), reflection-absorption infrared spectroscopy (RAIRS) and temperature programmed desorption (TPD). Upon CO adsorption, a new feature is observed in IPE at 4.4 eV above E_F and is interpreted as the CO 2π^∗ level. When adsorbed at room temperature, TPD exhibits a CO desorption peak at ∼355 K, while low temperature adsorption reveals additional binding configurations with TPD features at ∼220 K and ∼265 K. These TPD peak temperatures are correlated with different C-O stretch vibrational frequencies observed in the IR spectra. The adsorption properties of this surface are compared to those of the surfaces of single crystal hcp-Co, as well as other metastable thin film systems.     

Coverage effects on phenol adsorption on Si(1 0 0)2 × 1 as: A first principle calculation

We investigated the adsorption of a 6-dimers Si(1 0 0)2 × 1 surface as a function of coverage and adsorption type (molecular/dissociative) by first principle calculations. In particular, we performed calculations on models with 2, 3, 4 and 6 phenol molecules, corresponding to coverage Θ = 0.34, 0.5, 0.67 and 1. We found that total adsorption energy, when at least one phenol is in a molecular state is lower than the sum of the corresponding singly adsorbed molecules. The dissociative adsorption of multiple molecules, both in parallel and switched configuration is most favoured for a coverage Θ = 0.34 (2.6 eV per adsorbed molecule). This values decreases to 2.0 eV and remains constant till the coverage 1 is reached.The energy barrier for the molecular-to-dissociated transition of a phenol molecule, in presence of another dissociatively adsorbed molecule is ∼0.008 eV and it is similar to the value in case of single adsorption. Possible hydrogen displacements were also considered.     

Atom geometry of nanostructured Fe films grown on c(2 × 2)-N/Cu(1 0 0) surface: An investigation by X-ray absorption spectroscopy with multishell analysis

We investigated the growth of Fe nanostructured films on c(2 × 2)-N/Cu(1 0 0) surface with Fe K-edge X-ray absorption fine structure (XAFS) in the near edge and in the extended energy region. The high photon flux of the incident X-rays allowed us to perform multishell analysis of the XAFS oscillations for Fe coverage Θ_Fe < 1 ML. This data analysis yields a detailed investigation of the atom geometry and some insights in the film morphology. At Θ_N < 0.5 ML (N saturation coverage) there is absence of contribution to XAFS from N atoms. First shell analysis of linearly polarized XAFS gives Fe-Fe (or Fe-Cu) bond length values varying between R₁ = 2.526 ± 0.006 Å at the highest Fe coverage (3 ML ) and R₁ = 2.58 ± 0.01 Å at Θ_Fe = 0.5 ML, Θ_N = 0.3 ML, with incidence angle Θ = 35°. These values are different from the case of bcc Fe (R = 2.48 Å), and compatible with fcc Fe (R₁ = 2.52 Å) and fcc Cu (R₁ = 2.55 Å). At the Fe lowest coverage (Θ_Fe = 0.5 ML) the dependence of R₁ on the incidence angle indicates expansion of the outmost layer. Near edge spectra and multishell analysis can be well reproduced by fcc geometry with high degree of static disorder. At N saturation pre-coverage (Θ_N = 0.5 ML) the XAFS analysis has to keep into account the Fe-N bonding. The results suggest two different adsorption sites: one with Fe in a fcc hollow site, surrounded by other metal atoms as nearest neighbours, and one resulting from an exchange with a Cu atom underneath the N layer.     

Interactions between SO2 and NO on the surface of stepped Pt(3 3 2)

Interactions between S¹⁸O₂ and NO on the surface of stepped Pt(3 3 2) were studied using Fourier transform infra red reflection-absorption spectroscopy (FTIR-RAS) combined with thermal desorption spectroscopy (TDS). Adsorbed S¹⁸O₂ does not seem to have a preference for step sites on Pt(3 3 2). As such, the presence of S¹⁸O₂ molecules following exposures of ?1.6 L does not significantly block the subsequent adsorption of NO (?0.8 L) on these step sites. Adsorbed S¹⁸O₂ molecules undergo dissociation (S¹⁸O₂(a) → S¹⁸O(a) + ¹⁸O(a)) as the surface temperature is increased to 250 K and above, but the resultant ¹⁸O(a) further reacts with sulfur oxides (S¹⁸O₂(a) and S¹⁸O(a)) to form S¹⁸O_x (x > 2) species at ∼400 K and above. The S¹⁸O_x species desorb as S¹⁸O₂. Even though the presence of co-adsorbed S¹⁸O₂ suppresses NO dissociation and subsequent N₂ production, this effect is not significantly enhanced with increasing the exposures of S¹⁸O₂ in the range ?1.6 L; N₂ desorption is still detectable at an exposure of 1.6 L S¹⁸O₂, at which a considerable amount of S¹⁸O₂ desorption is detected.     

Dissociative adsorption and thermal evolution of dichloroethylenes on Ni(1 0 0)

The room temperature (RT) adsorption and thermal evolution of cis- and trans-dichloroethylene (DCE) and their structural isomer, iso-DCE, on Ni(1 0 0) have been studied by vibrational electron energy loss spectroscopy (EELS), Auger electron spectroscopy (AES) and thermal desorption spectrometry (TDS). For RT adsorption, both cis- and trans-DCE exhibit very similar EELS features that are different from those found for iso-DCE. These differences indicate the formation of different fragments upon RT adsorption. In particular, the primary adspecies for cis- and trans-DCE are ethane-1,1,2,2-tetrayl () and acetylide-like () adspecies along with a small amount of chlorovinyl adspecies, while ethylylidyne () is the more plausible adspecies for iso-DCE. The differences in the adstructures upon dissociative adsorption at RT underline the important isomeric effects. Furthermore, both AES and TDS results for all three DCE isomers show that most of the Cl atoms produced by dechlorination remain on the surface and its surface concentration remains unchanged upon annealing the samples above 500 K. Upon further annealing to 550 K, the EELS spectra of all three isomers exhibit a broad feature near 1600 cm⁻¹, which suggests the formation of carbon clusters on the surface. The presence of surface Cl atoms therefore appears to prevent the CC bond cleavage during thermal evolution of the adspecies on Ni(1 0 0).     

The effect of ferroelectric polarization on the interaction of water and methanol with the surface of LiNbO3(0 0 0 1)

Water and methanol temperature programmed desorption (TPD) measurements were performed on the positive (c⁺) and negative (c⁻) surfaces of poled ferroelectric lithium niobate (LiNbO₃) single crystals. The results indicate that the molecule-surface interactions are both coverage and polarization-dependent. From a comparison of the TPD spectra for the positive and negative surfaces, it is shown that the desorption temperatures of water and methanol are consistently lower on the negative surface by 15 K and 20 K, respectively. The TPD spectra were simulated using the Polanyi-Wigner equation with a coverage-dependent energy term. These calculations show that the polarization dependence of the desorption temperature is due to a difference in the zero-coverage desorption energies on the two surfaces equal to a few kJ per mole. The mechanism for the polarization effect is explored with in situ pyroelectric voltage measurements, which indicate that a surface voltage of ±2 mV develops in the LiNbO₃(0 0 0 1) samples during TPD measurements. The magnitude of the pyroelectric-induced surface charge is heating rate dependent.     

DFT study on dissociative adsorption of SiH4 and GeH4 on SiGe(1 0 0)-2 × 1 surface

SiH₄ and GeH₄ dissociative adsorptions on a buckled SiGe(1 0 0)-2 × 1 surface have been analyzed using density functional theory (DFT) at the B3LYP level. The Ge alloying in the Si(1 0 0)-2 × 1 surface affects the dimer buckling and its surface reactivity. Systematic Ge influences on the reaction energetics are found in SiH₄ and GeH₄ reactions with four dimers of Si^∗-Si, Ge^∗-Si, Ge^∗-Ge, and Si^∗-Ge (∗ denotes the protruded atom). On a half H-covered surface, the energy barriers for silane and germane adsorption are higher than those on the pristine surface. The energy barrier for silane adsorption is higher than the corresponding barrier for germane adsorption. Rate constants are also calculated using the transition-state theory. We conclude that the SiGe surface reactivity in adsorption reaction depends on the Ge presence in dimer form. If the surface Ge is present in form of Ge^∗-Ge, the surface reactivity decreases as the Ge^∗-Ge content increases. If the surface Ge prefers to be in form of Ge^∗-Si at low Ge contents, the surface reactivity increases first, then decreases at high Ge surface contents when Ge^∗-Ge prevails. The calculated rate constant ratio of GeH₄ adsorption on Si^∗-Si over Ge^∗-Ge at 650 °C is 2.1, which agrees with the experimental ratio of GeH₄ adsorption probability on Si(1 0 0) over Si(1 0 0) covered by one monolayer Ge. The experimental ratio is 1.7 measured through supersonic molecular beam techniques. This consistency between calculation and experimental results supports that one monolayer of Ge on Si(1 0 0) exists in form of Ge^∗-Ge dimer.     

Iron isotope effect on Tc in optimally-doped (Ba,K)Fe2As2 (Tc = 38 K) and SmFeAsO1−y (Tc = 54 K) superconductors

We report the iron isotope effect on a transition temperature (T_c) in an optimally-doped (Ba,K)Fe₂As₂ (T_c = 38 K) and SmFeAsO_1−y (T_c = 54 K) superconductors. In order to obtain the reliable isotope shift in T_c, twin samples with different iron isotope mass are synthesized in the same conditions (simultaneously) under high-pressure. We have found that (Ba,K)Fe₂As₂ shows an inverse iron isotope effect α_Fe = −0.18 ± 0.03 while SmFeAsO_1−y shows a small iron isotope effect α_Fe = −0.02 ± 0.01, where the isotope exponent α is defined by T_c ∼ M^−α (M is the isotopic mass). The results show that α_Fe changes in the iron-based superconductors depending on the system. The distinct iron isotope effects imply the exotic coupling mechanism in the iron-based superconductors.     

Structural transition in cyclooctatetraene adsorbed on Ru(0 0 1) probed by thermal desorption and two-photon photoemission spectroscopy

The adsorption of 1,3,5,7-cyclooctatetraene (COT) on Ru(0 0 1) is studied by temperature-programmed desorption (TPD), work function measurements, as well as time- and angle-resolved two-photon photoemission (2PPE) spectroscopy. The TPD data show that COT films grow at 115 K in a metastable phase when the coverage is increased from the chemisorbed monolayer to the bulk-like molecular multilayer structure. The metastable states desorb at a temperature which is ≈9 K lower than the desorption temperature of the stable multilayer. At 165 ± 2 K, they undergo an irreversible and thermally activated transformation into the stable multilayer phase. This transition is accompanied by a pronounced increase in the total 2PPE yield by more than one order of magnitude as well as the appearance of image potential states. The image states have binding energies of −0.70 eV and −0.24 eV for the n = 1 and n = 2 states, respectively, and a lifetime of 20 ± 5 fs for both states. Their appearance is interpreted as an indication of island formation in the stable multilayer regime. 2PPE spectroscopy of the image potential states provides a sensitive probe of structural transitions in the adsorbate layers.     

Shell model calculations of the adsorption and diffusion of K, Cl, and KCl on KCl(0 0 1)

Equilibrium adsorption positions and diffusion pathways of the ions K⁺ and Cl⁻ as well as of the molecule KCl on the terrace of the (0 0 1) surface of KCl were determined by shell model calculations allowing relaxations of the crystal lattice in the vicinity of the adsorbed species. For the ions each one adsorption position was found, in which the ions are located above the hollow site at the center of a slightly distorted square formed by two cations and two anions of the uppermost surface layer of the KCl crystal. Adsorption energies of −1.52 eV for K⁺ and −1.61 eV for Cl⁻ were calculated. Jumps of the ions occur from these positions to adjacent hollow positions in the ±[1 0 0] and ±[0 1 0] directions with a jump distance of a₀/2. The activation energies for the jumps result as 0.142 for K⁺ and 0.152 eV for Cl⁻ and the mean diffusion lengths as and . For the KCl molecule four distinct adsorption minima with energies between −0.932 and −0.825 eV were found. Because of the smaller lattice relaxation caused by the molecule the adsorption energies are considerably lower than for the single ions. In the position with the largest adsorption energy the ions of the admolecule are again placed above adjacent hollow sites. In two more adsorption positions only one ion is at the hollow site and the other one in a top position above an oppositely charged ion of the surface. In the fourth position with the smallest adsorption energy both ions are in top positions. Jumps between the different adsorption positions proceed by rotations of the molecule, in which one of its ions remains essentially attached to a local minimum position. The diffusion and desorption of a KCl molecule was studied by a Monte Carlo method, resulting in a mean diffusion length x_s (nm) = 0.39 exp[0.84 (eV)/2kT], which agrees rather well with an experimental value of . Values for the mean stay time as well as for the surface diffusion coefficient are derived.     

Hexaphenyl thin films on clean and carbon covered Au(1 1 1) studied with TDS and LEED

The adsorption and growth of ordered para-hexaphenyl (6P) films have been investigated both on clean and partially carbon pre-covered Au(1 1 1) single crystal surfaces by thermal desorption spectroscopy (TDS) and low energy electron diffraction (LEED) under ultra-high vacuum conditions. The existence of a distinct first and second monomolecular 6P layer that clearly separate from the multilayer regime, which comprise lying molecules with respect to the substrate surface, could be inferred from TDS. For both the 6P mono- and multilayer grown on pure Au(1 1 1) the desorption energies have been determined based on experimental TDS data. In particular, for the monolayer regime a coverage dependence of the desorption energy has been found, which is attributed to repulsive interactions between neighbouring 6P molecules adsorbed on the gold surface. The existence of well-ordered film structures could be inferred from LEED for half monolayer and full monolayer thick 6P films. Based on the LEED and TDS data, structural models are presented for these highly ordered organic films. Multi-step dehydrogenation of 6P molecules adsorbed on clean Au(1 1 1) surfaces is reported for temperatures above 650 K together with experimental evidence for the existence of a regular overlayer composed of partially dehydrogenated polycyclic aromatic hydrocarbon (PAH) intermediates. A quite different adsorption/desorption kinetics and film growth has been observed for 6P films grown on carbon pre-covered Au(1 1 1) surfaces.     

Anomalous adsorption of Cs on Pt(1 1 1)

The adsorption of Cs on Pt(1 1 1) surfaces and its reactivity toward oxygen and iodine for coverages θ_Cs?0.15 is reported. These surfaces show unusual “anomalous” behavior compared to higher coverage surfaces. Similar behavior of K on Pt(1 1 1) was previously suggested to involve incorporation of K into the Pt lattice. Despite the larger size of Cs, similar behavior is reported here. Anomalous adsorption is found for coverages lower than 0.15 ML, at which point there is a change in the slope of the work function. Thermal Desorption Spectroscopy (TDS) shows a high-temperature Cs peak at 1135 K, which involves desorption of Cs⁺ from the surface.The anomalous Cs surfaces and their coadsorption with oxygen and iodine are characterized by Auger Electron Spectroscopy (AES), TDS and Low Electron Energy Diffraction (LEED). Iodine adsorption to saturation on Pt(1 1 1)(anom)-Cs give rise to a sharp LEED pattern and a distinctive work function increase. Adsorbed iodine interacts strongly with the Cs and weakens the Cs-Pt bond, leading to desorption of Cs_xI_y clusters at 560 K. Anomalous Cs increases the oxygen coverage over the coverage of 0.25 ML found on clean Pt. However, the Cs-Pt bond is not significantly affected by coadsorbed oxygen, and when oxygen is desorbed the anomalous cesium remains on the surface.     

A Monte Carlo simulation study of H2 layers on NaCl(0 0 1)

Monte Carlo simulations show that, at one monolayer coverage, H₂ molecules adsorbed on a NaCl(0 0 1) surface occupy all Na⁺ sites and form a commensurate c(2 × 2) structure. If the Cl⁻ sites are occupied as well, a bi-layer p(2 × 1) structure forms. An examination of the H₂ molecules’ rotational motion shows the molecular axes are azimuthally delocalized and so both of the structures acquire (1 × 1) symmetry in accord with experimental observations. These calculations also show that helicoptering o-H₂ (J = 1, m = ±1) prefer to sit on top of Na⁺ sites, while cartwheeling o-H₂ (J = 1, m = 0) prefers to locate over Cl⁻ sites, in agreement with other work.     

Effects of potassium on the reaction pathways of CH2 fragment over Mo2C/Mo(1 0 0)

The adsorption and surface reactions of CH₂I₂ on the K-dosed Mo₂C/Mo(1 0 0) have been studied by high resolution electron energy loss spectroscopy, X-ray photoelectron spectroscopy and thermal desorption spectroscopy. Potassium is an effective promoter for the rupture of C-I bond in the adsorbed CH₂I₂. A partial dissociation of this compound occurred even at 100 K and was completed at 190 K at monolayer K coverage. The dissociation was further promoted by the illumination of coadsorbed layer at 100 K. As revealed by HREELS and XPS measurements the primary products of the dissociation are CH₂ and I. Methylene was converted to π-bonded ethylene characterized by T_p = 160 K, and di-σ-ethylene with T_p = 350 K. Other products of the surface reaction are hydrogen and methane. The coupling reaction of CH₂ species was clearly facilitated by potassium. The effect of potassium was explained by the extended electron donation to adsorbed alkyl iodide in one hand, and by the direct interaction between potassium and I on the other hand.     

Variable-temperature FT-IR studies on the thermodynamics of carbon dioxide adsorption on a faujasite-type H-Y zeolite

Adsorption of carbon dioxide on a faujasite-type H-Y zeolite (Si:Al = 2.6:1) was studied by variable-temperature (200-290 K range) infrared spectroscopy. Adsorbed CO₂ molecules interact with the Brønsted acid Si(OH)Al groups located inside the zeolite supercage, bringing about a characteristic bathochromic shift of the O-H stretching mode from 3645 cm⁻¹ (free OH group) to 3540 cm⁻¹ (hydrogen-bonded CO₂ adsorption complex). Simultaneously, the asymmetric (ν₃) mode of adsorbed CO₂ is observed at 2353 cm⁻¹. From the observed variation of the integrated intensity of the 3645 and 2353 cm⁻¹ IR absorption bands upon changing temperature, corresponding values of standard adsorption enthalpy and entropy were found to be ΔH° = −28.5(±1) kJ mol⁻¹ and ΔS° = −129(±10) J mol⁻¹ K⁻¹. Comparison with the reported values of ΔH° for CO₂ adsorption on other zeolites is briefly discussed.