Determination of alkylphenols and alkylphenol ethoxylates in sewage sludge: effect of sample pre-treatment

A complete characterization of sewage sludge collected from five biological waste water treatment plants was done to determine physico-chemical parameters, heavy metals and alkylphenols, making special emphasis on sampling, homogenization, and sample pre-treatment. Ultrasonic extraction followed by gas chromatrography coupled with mass spectrometry was used to evaluate the effect of sample pre-treatment (untreated sample, freeze-drying, drying at 40 °C or drying at 100 °C) on the concentration of octylphenol (OP), nonylphenol (NP) and nonylphenol ethoxylates (NP₁EO, NP₂EO). Untreated samples and samples dried at 100 oC gave concentration levels up to 62% and 89% lower, respectively, than freeze-dried samples. In 50% of cases, freeze-dried samples led to significantly higher concentrations than those obtained by drying at 40 °C. Thus, freeze-drying is the recommended sample pre-treatment to prevent possible losses of OP, NP, and NP₁EO. Using this methodology, concentrations detected were from 3.2 to 199 mg kg⁻¹ being NP followed by NP₁EO found in highest concentration. The total concentration of NP and NP₁EO exceeded the limit of 50 mg kg⁻¹ proposed by the draft European directive on sewage sludge in three out of five samples studied. Contrarily, heavy metals were below the legislated values.     

Monoclonal antibody-based enzyme-linked immunosorbent assay for detection of total malachite green and crystal violet residues in fishery products

A rapid easy-to-use trace level direct competitive enzyme-linked immunosorbent assay (dc-ELISA) detection of total residual malachite green (MG), crystal violet (CV) and their corresponding primary metabolites leucomalachite green (LMG) and leucocrystal violet (LCV) in fishery products in a single assay was developed. The monoclonal antibodies, anti-MG and anti-CV mAbs, were prepared using carboxyl-malachite green (CMG) and cationized bovine serum albumin (cBSA) conjugates as immunogen. The linear range for the quantitative detection of total MG, CV and their primary metabolites LMG and LCV was between 0.15 to 4.5?ng?mL^?1 with a half maximal inhibitory concentration (IC₅₀) at 0.56?±?0.04?ng?mL^?1 (n?=?5). The anti-MG mAbs exhibited 98% cross-reactivity to CV, less than 0.1% cross-reactivity with LMG and LCV, and no cross-reactivity with chloramphenicol, enrofloxacin, sulfadiazine, and tetracycline. Application of the dc-ELISA in fish tissue samples gave a limit of detection (LOD) of 0.37?ng?g^?1. The improved total detection lead to a recovery of 74.60?±?8.38% at 0.5?ng?g^?1 and 87.47?±?12.83% at 2.0?ng?g^?1 that was better than existing techniques. The dc-ELISA showed total MG in 7 out of 44 field fish samples that were confirmed with LC-MS/MS. The easy-to-use, inexpensive, and rapid dc-ELISA for the detection of total MG, CV and their corresponding primary metabolites holds promise for field applications.     

Single robust RP-HPLC analytical method for quantification of curcuminoids in commercial turmeric products,Ayurvedic medicines,and nanovesicular systems

A single robust reversed-phase high-performance liquid chromatography (RP-HPLC) method was developed and validated as per International Conference on Harmonization guidelines for the accurate quantification of curcuminoids in commercial turmeric products, Ayurvedic medicines, and nanovesicular systems. The proposed chromatographic method was found to be specific, linear (r²?≥?0.999), precise at intra- and inter-day levels (percentage relative standard deviation <2.0%), accurate (percentage recovery 99.14–102.29%), and robust. The limits of detection and quantification were found to be 7.40 and 24.70?ng?mL^?1 for curcumin, 9.24 and 30.80?ng?mL^?1 for demethoxycurcumin, and 6.48 and 21.61?ng?mL^?1 for bisdemethoxycurcumin, respectively. Among different commercial turmeric products and Ayurvedic medicines tested, the contents of curcumin (3.54?±?0.06–25.8?±?0.08?mg?g^?1), demethoxycurcumin (1.28?±?0.02–9.97?±?0.03?mg?g^?1), and bisdemethoxycurcumin (0.50?±?0.01–5.97?±?0.01?mg?g^?1) varied significantly. The developed method was effectively applied to the determination of encapsulation efficiency of curcuminoids (ranged between 84.33?±?3.50 and 96.59?±?2.53%) in the nanovesicular systems. In conclusion, the reported method is suitable for the analysis of curcuminoids in a wide variety of turmeric products and used for the quality control of products that contain curcuminoids.     

Chemical modification of alumina surface by immobilization of 1-((5-nitrofuran-2-yl)methylene)thiosemicarbazide for extractive concentration of silver ions

A column, solid phase extraction (SPE), preconcentration method was developed for determination of silver by using alumina coated with 1-((5-nitrofuran-2-yl)methylene)thiosemicarbazide and determination by flame atomic absorption spectrometry. The separation/preconcentration conditions for the quantitative recovery were investigated. At pH 2, the maximum sorption capacity of Ag⁺ was 7.5?mg?g^?1. The linearity was maintained in the concentration range of 0.02–11.0?µg?mL^?1 in the final solution or 0.14–1.10?×?10^4?ng?mL^?1 in the original solution for silver. The preconcentration factor of 140 and relative standard deviation of ±1.4% was obtained, under optimum conditions. The limit of detection (LOD) was calculated as 0.112?ng?mL^?1, based on 3σ_bl/m (n?=?8) in the original solutions. The proposed method was successfully applied to the determination trace amounts of silver in the environmental samples such as tea, rice and wheat flour, mint, and real water samples.     

The loading of polyoxometalates compound on a biomass derived N-doped mesoporous carbon matrix,a composite material for electrical energy storage

Abstract

A polyoxometalate (POM)-based composite material (NiPW₁₂NP/NMC) was synthesized, in which the nanoparticle of a POM compound (NiPW₁₂NP) distributes on orange juice derived nitrogen doped mesoporous carbon matrix (NMC) homogenously. When employed as a cathode material, NiPW₁₂NP/NMC exhibits high specific capacitance, remarkable rate capability and long-term stability. When the current density is 4?A·g^?1, a specific capacitance as high as 547 F·g^?1 is achieved by NiPW₁₂NP/NMC. With NiPW₁₂NP/NMC serving as cathode and MnO₂ acting as anode, a high performance asymmetric supercapacitor is assembled, which possesses a high energy density of 10.88?Wh·kg^?1 at 0.64?kW·kg^?1. It also shows a good rate capability, when the current density increases from 4 to 12?A·g^?1, its specific capacitance decreases from 113 to 88 F·g^?1, with 77.9% capacitance retention. After 5000 cycles charge-discharge experiments, 92.8% of its capacitance can be maintained, which exhibits good stability.     

Chemical characterisation of a new estuarine pollutant (2,4-Dichloro-6-Nitrophenol) and assessment of the acute toxicity of its quinoid form for Artemia salina

It is known that the compound 2,4-dichloro-6-nitrophenol (2,4DC6NP) is formed upon nitration of 2,4-dichlorophenol, which in turn is a transformation intermediate of the herbicide dichlorprop. However, the chemical and spectroscopic characteristics of 2,4DC6NP, as well as its toxicity, are poorly known. This work shows that 2,4DC6NP behaves as a diprotic acid in aqueous solutions, with pK_a values of 3.0?±?0.9 and 4.9?±?0.5. At pH?<?3, 2,4DC6NP would undergo protonation. The absorption spectra suggest that anionic 2,4DC6NP, which prevails at pH?>?5 would have an ortho-quinoid structure that is responsible for the absorption peak centred at 428?nm. Considering that 2,4DC6NP has been detected in the brackish lagoons of the Rhône delta (southern France), where its levels are comparable to those of the parent herbicide, it is necessary to examine the possible effects of 2,4DC6NP on the species living in that environment. For this reason, the acute toxicity of the anionic form of 2,4DC6NP was assessed for the brine shrimp Artemia salina, a zooplankton species that lives both in brackish and in saline aquatic environments. The toxicity test yielded a LC₂₀ value of 8?±?2?mg?L^?1 and a LC₅₀ value of 18.7?±?0.8?mg?L^?1. Such values are safely higher than the maximum detected concentration of 2,4DC6NP in the Rhône delta lagoons. Further studies should be concentrated on the long-term effects of 2,4DC6NP, and in particular on its potential genotoxicity.     

Synthesis and characterization of novel alternating fluorinated copolymers bearing oligo(ethylene oxide) side chains

The synthesis and characterization of novel poly(CTFE‐g‐oligoEO) graft copolymers [chlorotrifluoroethylene (CTFE) and ethylene oxide (EO)] are presented. First, vinyl ether monomers bearing oligo(EO) were prepared by transetherification of ω‐hydroxyoligo(EO) with ethyl vinyl ether catalyzed by a palladium complex in 70–84% yields. Two vinyl ethers of different molecular weights (three and 10 EO units) were thus obtained. Then, radical copolymerization of the above vinyl ethers with CTFE led to alternating poly(CTFE‐alt‐VE) copolymers that bore oligo(OE) side chains in satisfactory yields (65%). These original poly(CTFE‐g‐oligoEO) graft copolymers were characterized by ¹H, ¹⁹F, and ¹³C NMR spectroscopy. Their molecular weights reached 19,000 g mol^?1, and their thermal properties were investigated while their glass transition temperatures ranged between ?42 and ?36 °C. Their thermogravimetric analyses under air showed decomposition temperatures of 270 °C with 10% weight loss (T_d,10%). These novel copolymers are of potential interest as polymer electrolytes in lithium ion batteries, showing room temperature conductivities ranging from 4.49 × 10^?7 to 1.45 × 10^?6 S cm^?1 for unplasticized material. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Equilibrium investigation of complex formation reactions involving copper(II), nitrilo-tris(methyl phosphonic acid) and amino acids,peptides or DNA constitutents. The kinetics,mechanism and correlation of rates with complex stability for metal ion promoted hydrolysis of glycine methyl ester

The complex formation reactions of [Cu(NTP)(OH₂)]^4? (NTP?=?nitrilo-tris(methyl phosphonic acid)) with some selected bio-relevant ligands containing different functional groups, are investigated. Stoichiometry and stability constants for the complexes formed are reported. The results show that the ternary complexes are formed in a stepwise mechanism whereby NTP binds to copper(II), followed by coordination of amino acid, peptide or DNA. Copper(II) is found to form Cu(NTP)H _n species with n?=?0, 1, 2 or 3. The concentration distribution of the various complex species has been evaluated. The kinetics of base hydrolysis of glycine methyl ester in the presence of copper(II)-NTP complex is studied in aqueous solution at different temperatures. It is proposed that the catalysis of GlyOMe ester occurs by attack of OH^? ion on the uncoordinated carbonyl carbon atom of the ester group. Activation parameters for the base hydrolysis of the complex [Cu(NTP)NH₂CH₂CO₂Me]^4? are, ΔH^±?=?9.5?±?0.3?kJ?mol^?1 and ΔS^±?=??179.3?±?0.9?J?K^?1?mol^?1. These show that catalysis is due to a substantial lowering of ΔH^±.     

Determination of priority pollutants in aqueous samples by dispersive liquid–liquid microextraction

A dispersive liquid–liquid microextraction (DLLME) method followed by high-performance liquid chromatography–triple quadrupole mass spectrometry has been developed for the simultaneous determination of linear alkylbenzene sulfonates (LAS C₁₀, C₁₁, C₁₂, and C₁₃), nonylphenol (NP), nonylphenol mono- and diethoxylates (NP₁EO and NP₂EO), and di-(2-ethylhexyl)phthalate (DEHP). The applicability of the method has been tested by the determination of the above mentioned organic pollutants in tap water and wastewater. Several parameters affecting DLLME, such as, the type and volume of the extraction and disperser solvents, sample pH, ionic strength and number of extractions, have been evaluated. Methanol (1.5 mL) was selected among the six disperser solvent tested. Dichlorobenzene (50 μL) was selected among the four extraction solvent tested. Enrichment factor achieved was 80. Linear ranges in samples were 0.01–3.42 μg L⁻¹ for LAS C₁₀–₁₃ and NP₂EO, 0.09–5.17 μg L⁻¹ for NP₁EO, 0.17–9.19 μg L⁻¹ for NP and 0.40–17.9 μg L⁻¹ for DEHP. Coefficients of correlation were higher than 0.997. Limits of quantitation in tap water and wastewater were in the ranges 0.009–0.019 μg L⁻¹ for LAS, 0.009–0.091 μg L⁻¹ for NP, NP₁EO and NP₂EO and 0.201–0.224 μg L⁻¹ for DEHP. Extraction recoveries were in the range from 57 to 80%, except for LAS C₁₀ (30–36%). The method was successfully applied to the determination of these pollutants in tap water and effluent wastewater from Seville (South of Spain). The DLLME method developed is fast, easy to perform, requires low solvent volumes and allows the determination of the priority hazardous substances NP and DEHP (Directive 2008/105/EC).     

Synthesis and electro-optical features of a high T g polymer system with excellent electro-optic activity and thermal stability

Three chromophores with tricyanofuran and tricyanopyrroline electron acceptors were synthesized and doped in high glass transition temperature (T _g) polymer poly(N-(4-acetoxylphenyl)maleimide-co-styrene, NAPMI-co-ST). The electro-optic (EO), optical, and thermal properties of the doped poly(NAPMI-co-ST) were characterized and discussed. After being corona poled under 12?kV, this high T _g polymer material showed excellent EO activity and thermal stability. The highest EO coefficient (r ₃₃) reached 48.2?pm?V^?1 (1,310?nm) and could remain 90?% of the original value for 100?h at 85?°C. The EO coefficient was relatively higher compared with other high T _g EO polymers. The thermal stability was also very good and the manufacture process was convenient and applicable for device fabrication.     

Spatial and seasonal behaviour of organotin compounds in protected subtropical estuarine ecosystems in Okinawa,Japan

The spatial and temporal behaviours of the organotin compounds (OTCs) (butyl- and phenyltin) were investigated in the Manko and Okukubi protected estuarine ecosystems on Okinawa Island, Japan from February to October 2006. Butyltin compounds (BTCs) were frequently detected in all seasons, while phenyltin (PhTs) were found in winter and early spring. In Manko estuary, the total mean concentrations of BTCs and PhTs were 22.78?±?30.85, (mean?±?SD, n?=?53) and 0.08?±?0.27?ng(Sn)?L^?1, respectively. In Okukubi estuary, BTCs and PhTs were 12.58?±?23.96 and 0.47?±?1.67 (n?=?55) ng(Sn)?L^?1, respectively. The Manko sediments can be classified as lightly contaminated, while the Okukubi sediments were uncontaminated with tributyltin (TBT). The mean levels of TBT shown in Manko estuary exceeded the threshold level and represent an ecotoxicological risk to sensitive aquatic life. Generally, the present study reports the occurrence and continuous input of OTCs in the protected estuaries, even 16 years after legal restriction of TBT usage in coastal waters was implemented by the Japanese Environmental Authorities.     

Calorimetric studies on the thermal decomposition of tri n-butyl phosphate-nitric acid systems

Thermal decomposition of neat TBP, acid-solvates (TBP·1.1HNO₃, TBP·2.4HNO₃) (prepared by equilibrating neat TBP with 8 and 15.6?M nitric acid) with and without the presence of additives such as uranyl nitrate, sodium nitrate and sodium nitrite, mixtures of neat TBP and nitric acid of different acidities, 1.1?M TBP solutions in diluents such as n-dodecane (n-DD), n-octane and isooctane has been studied using an adiabatic calorimeter. Enthalpy change and the activation energy for the decomposition reaction derived from the calorimetric data wherever possible are reported in this article. Neat TBP was found to be stable up to 255?°C, whereas the acid-solvates TBP·1.1HNO₃ and TBP·2.4HNO₃ decomposed at 120 and 111?°C, respectively, with a decomposition enthalpy of ?495.8?±?10.9 and ?1115.5?±?8.2?kJ?mol^?1 of TBP. Activation energy and pre exponential factor derived from the calorimetric data for the decomposition of these acid-solvates were found be 108.8?±?3.7, 103.5?±?1.4?kJ?mol^?1 of TBP and 6.1?×?10¹⁰ and 5.6?×?10⁹?S^?1, respectively. The thermochemical parameters such as, the onset temperature, enthalpy of decomposition, activation energy and the pre-exponential factor were found to strongly depend on acid-solvate stoichiometry. Heat capacity (C _p ), of neat TBP and the acid-solvates (TBP·1.1HNO₃ and TBP·2.4HNO₃) were measured at constant pressure using heat flux type differential scanning calorimeter (DSC) in the temperature range 32?C67?°C. The values obtained at 32?°C for neat TBP, acid-solvates TBP·1.1HNO₃ and TBP·2.4HNO₃ are 1.8, 1.76 and 1.63?J?g^?1?K^?1, respectively. C _p of neat TBP, 1.82?J?g^?1?K^?1, was also measured at 27?°C using ??hot disk?? method and was found to agree well with the values obtained by DSC method.     

Design and synthesis of fluorescent symmetric bis-triazolylated-1,4-dihydropyridines as potent antibreast cancer agents

Herein, we report the synthesis of fluorescent 1,4-dihydropyridine-linked bis-triazoles (2a–2n) through Hantzsch synthesis by the condensation of o/m-chloro-substituted benzaldehyde, ethyl 3-oxo-4(prop-2-yn-1-yloxy)butanoate, and ammonium acetate in the presence of Ba(NO₃)₂ as a catalyst followed by the click reaction of resultant Hantzsch product (1) with various aromatic as well as aliphatic azides. All the synthesized compounds were well characterized by ¹H-NMR, ¹³C-NMR, FTIR, and HRMS spectral techniques. Antibreast cancer evaluation of all the synthesized derivatives revealed that the compounds 2f (IC₅₀?=?7?±?0.02?µM) and 2g (IC₅₀?=?5?±?0.03?µM) showed better anticancer activity (lower IC₅₀) than the standard drug tamoxifen (IC₅₀?=?11.2?±?0.01?µM) against breast carcinoma (MDA-MB-231) cell line. The synthesized compounds were also screened against normal human embryonic kidney (HEK-293) cell line and found to be nontoxic. The fluorescent nature and cytotoxicity assay of these newly synthesized hybrids recommend their utility in tumor cell imaging.     

Rate constants for the gas-phase reactions of alkanes with Cl atoms at 296 ± 2 K

Rate constants for the gas-phase reactions of the Cl atom with a series of alkanes have been determined at 296 ± 2 K using a relative rate method. Using a rate constant for the Cl atom reaction with n-butane of 1.94 × 10^?10 cm³ molecule^?1 s^?1, the rate constants obtained (in units of 10^?11 cm³ molecule^?1 s^?1) were: 2-methylpentane, 25.0 ± 0.8; 3-methylpentane, 24.8 ± 0.6; cyclohexane, 30.8 ± 1.2; cyclohexane-d₁₂, 25.6 ± 0.8; 2,4-dimethylpentane, 25.6 ± 1.2; 2,2,3-trimethylbutane, 17.9 ± 0.7; methylcyclohexane, 34.7 ± 1.2; n-octane, 40.5 ± 1.2; 2,2,4-trimethylpentane, 23.1 ± 0.8; 2,2,3,3-tetramethylbutane, 15.6 ± 0.9; n-nonane, 42.9 ± 1.2; n-decane, 48.7 ± 1.8; and cis-bicyclo[4.4.0]decane, 43.1 ± 0.8, where the indicated errors are two least-squares standard deviations and do not include the uncertainties in the n-butane rate constant. These data have been combined with rate constants obtained previously for ten C₂? C₇ alkanes and this entire data set has been used to develop an estimation method allowing the room temperature rate constants for the reactions of the Cl atom with alkanes to be calculated. © 1995 John Wiley & Sons, Inc.     

Synthesis,structure, and kinetic studies on [RuCl2(NCCH3)2(cod)]

[RuCl₂(NCCH₃)₂(cod)], an alternative starting material to [RuCl₂(cod)] _n for the preparation of ruthenium(II) complexes, has been prepared from the polymer compound and isolated in yields up to 87% using a new work-up procedure. The compound has been obtained as a yellow solid without water of crystallization. The complexes [RuCl₂(NCR)₂(cod)] spontaneously transform into dimers [Ru₂Cl(μ-Cl)₃(cod)₂(NCR)] (R?=?Me, Ph). ¹H NMR kinetic experiments for these transformations evidenced first-order behavior. [RuCl₂(NCPh)₂(cod)] dimerizes slower by a factor of ten than [RuCl₂(NCCH₃)₂(cod)]. The following activation parameters, ΔH ^#?=?114?±?3?kJ?mol^?1 and ΔS ^#?=?66?±?9?J?K^?1?mol^?1 for R?=?CH₃CN (ΔG ^#?=?94?±?5?kJ?mol^?1, 298.15?K) and ΔH ^#?=?122?±?2?kJ?mol^?1 and ΔS ^#?=?75?±?6?J?K^?1?mol^?1 for R?=?Ph (ΔG ^#?=?100?±?4?kJ?mol^?1, 298.15?K), have been calculated from the first-order rate constants in the temperature range 294–323?K. The kinetic parameters are in agreement with a two-step mechanism with dissociation of acetonitrile as the rate-determining step. The molecular structures of [Ru₂Cl(μ-Cl)₃(cod)₂(NCR)] (R?=?Me, Ph) have been determined by X-ray diffraction.     

Résonance Magnétique Nucléaire en phase nématique. Exploration de la barrière d'empêchement à la libre rotation de la monofluoroacétone

The NMR spectra of monochloro-, monobromo- and monofluoroacetone (CH₃? CO? CH₂X with X = Cl, Br, F) oriented in a nematic phase have been measured and the direct dipolar coupling constants determined. The barrier to internal rotation for the CH₂F group has been studied for fluorine compound using various hypotheses. The best agreement with IR data has been obtained using the potential equation V(θ) = Σ_n V_n × (1 – cos nθ)/2 and a Boltzmann distribution of the CH₂F group (V₁ = 250 ± 50 cal.mol^?1, V₂ = 1650 ± 100 cal.mol^?1, V₃ = ?1000 ± 100 cal.mol^?1).     

Analysis of Six Phenolic Endocrine Disrupting Chemicals in Surface Water and Sediment

An efficient and reliable method based on gas chromatography–mass spectrometry (GC–MS) was developed for the extraction and analysis of six phenolic endocrine disrupting chemicals (EDCs), such as 4-nonylphenol (4-NP), nonylphenol-mono-ethoxylate (NP1EO), nonylphenol-di-ethoxylate (NP2EO), 4-tert-octylphenol (4-t-OP), bisphenol A (BPA) and 4-cumylphenol (4-CP) in surface water and sediment. The method was developed by using microwave-assisted extraction (MAE), solid phase extraction (SPE) and derivatization procedure. The MAE procedures were performed by optimizing three key process factors, consisted of extraction solvent, extraction temperature and holding time, affecting the extraction efficiency from sediment samples. For SPE, various parameters that may affect the recovery efficiency of water samples, such as SPE phase cartridge, elution solvent, as well as pH of water samples, were investigated. A series of derivatization conditions, such as derivatization reagent, reaction temperature and reaction time, were improved. The method achieved good repeatability and reproducibility with relative standard deviations <13% for all target EDCs in the both samples. Satisfactory recoveries for spiked water and sediment samples ranged from 85 to 101% and 74 to 105%, respectively. The limits of quantification varied from 0.20 (4-t-OP) to 11.50 ng L^?1 (NP2EO) and from 0.31 (4-t-OP) to 9.50 ng g^?1 dry weight (dw) (NP2EO) for water samples and sediment samples, respectively. The established method was successfully applied to the analysis of target EDCs in surface water and sediment samples collected from Caohai site of Dianchi Lake, China. The results showed that NP1EO, NP2EO and BPA were the three dominant phenolic EDCs in the site, reaching 114, 97 and 149 ng L^?1 in surface water, while 444, 186 and 178 ng g^?1 dw in surface sediment, respectively.     

Cross section measurements for 141Pr(n,γ)142Pr reaction at neutron energies from 13.5 to 14.8?MeV

Activation cross-sections were measured for the ¹⁴¹Pr(n,??)¹⁴²Pr reaction at three different neutron energies from 13.5 to 14.8?MeV. The fast neutrons were produced via the ³H(d,n)⁴He reaction on Pd-300 neutron generator. The natural high-purity Pr₂O₃ powder was used as target material. Induced gamma activities were measured by a high-resolution gamma-ray spectrometer with high-purity germanium detector. Measurements were corrected for gamma-ray attenuations, random coincidence (pile-up), dead time and fluctuation of neutron flux. The neutron fluences were determined by the cross section of ²⁷Al(n,??)²⁴Na reaction. The neutron energy in the measurement were by the cross section ratios of ⁹⁰Zr(n,2n)^89m+gZr and ⁹³Nb(n,2n)^92mNb reactions. The data for ¹⁴¹Pr(n,??)¹⁴²Pr reaction cross sections are reported to be 3.3?±?0.2, 2.7?±?0.2 and 2.2?±?0.2 mb at 13.5?±?0.2, 14.1?±?0.2, and 14.8?±?0.2?MeV incident neutron energies, respectively. Results were discussed and compared with some corresponding values found in the literature.     

Kinetics of phenyl radical reactions with propane,n‐butane,n‐hexane,and n‐octane: Reactivity of C6H5 toward the secondary C?H bond of alkanes

The kinetics of C₆H₅ reactions with n‐C_nH_2n+2 (n = 3, 4, 6, 8) have been studied by the pulsed laser photolysis/mass spectrometric method using C₆H₅COCH₃ as the phenyl precursor at temperatures between 494 and 1051 K. The rate constants were determined by kinetic modeling of the absolute yields of C₆H₆ at each temperature. Another major product C₆H₅CH₃ formed by the recombination of C₆H₅ and CH₃ could also be quantitatively modeled using the known rate constant for the reaction. A weighted least‐squares analysis of the four sets of data gave k (C₃H₈) = (1.96 ± 0.15) × 10¹¹ exp[?(1938 ± 56)/T], and k (n‐C₄H₁₀) = (2.65 ± 0.23) × 10¹¹ exp[?(1950 ± 55)/T] k (n‐C₆H₁₄) = (4.56 ± 0.21) × 10¹¹ exp[?(1735 ± 55)/T], and k (n?C₈H₁₈) = (4.31 ± 0.39) × 10¹¹ exp[?(1415 ± 65)T] cm³ mol^?1 s^?1 for the temperature range studied. For the butane and hexane reactions, we have also applied the CRDS technique to extend our temperature range down to 297 K; the results obtained by the decay of C₆H₅ with CRDS agree fully with those determined by absolute product yield measurements with PLP/MS. Weighted least‐squares analyses of these two sets of data gave rise to k (n?C₄H₁₀) = (2.70 ± 0.15) × 10¹¹ exp[?(1880 ± 127)/T] and k (n?C₆H₁₄) = (4.81 ± 0.30) × 10¹¹ exp[?(1780 ± 133)/T] cm³ mol^?1 s^?1 for the temperature range 297‐‐1046 K. From the absolute rate constants for the two larger molecular reactions (C₆H₅ + n‐C₆H₁₄ and n‐C₈H₁₈), we derived the rate constant for H‐abstraction from a secondary C? H bond, k_s?CH = (4.19 ± 0.24) × 10¹⁰ exp[?(1770 ± 48)/T] cm³ mol^?1 s^?1. © 2003 Wiley Periodicals, Inc. Int J Chem Kinet 36: 49–56, 2004