Derivatization of Humic Compounds: An Analytical Approach for Bound Organic Residues

Abstract

Bound residues of pesticides and their metabolites are defined as being nonextractable with organic solvents, but partly extractable together with the humic matrix by NaOH or other solvents suitable to extract humic compounds. Recently, an improvement in humus extraction from soils was achieved upon derivatization of the organic matter with silylating reagents at room temperature. By this method 70–90% of the organic carbon or nitrogen either from soil or from humin became soluble in organic solvents. The extracts were analyzed by means of ¹³C NMR-spectroscopy. The spectra were well resolved with signal-separation of less than 1 ppm. The extracted humic compounds were of rather low molecular weight, ranging from 300 to 4000 to 6000 d or more.

¹⁴C-labeled residues of pesticides or other xenobiotics found to be nonextractable after exhaustive organic solvent extraction became readily dissolved along with most of the humic matrix using this derivatization procedure. Between 60–80% of ¹⁴C anilazine residues or of ¹⁴C-labeled chlorinated phenols or anilines originating from both previously solvent extracted soil samples or from humin became solubilized in organic solvents.     

Extractability of dioxins from soil: I. Extractability of dioxins from airborne particulates and humic acid fraction in soil

The extractability of dioxins (polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans, and coplanar polychlorinated biphenyls) from airborne particulates (APs) and humic acid (HA) in soil was evaluated. APs collected from ambient atmosphere and dioxins-associated precipitated HA fraction (PHA) were extracted by pressurized liquid extraction with either toluene or acetone. Native dioxins were equivalently extracted from APs with both solvents, whereas only acetone could satisfactorily recover the ¹³C-labelled compounds from metal-free PHA. The recovery rates of dioxins by toluene extraction from metal-free PHA varied with the organic carbon content of the PHA. However, even with acetone, the recovery of dioxins from metal-bound HA was poor (11–40%). These results suggest that PHA prevented the solvents from accessing sequestered dioxins. This characteristic of solid HA may influence the extractability of dioxins from humus-rich soil.     

Evaluation of Extraction Procedures of Organochlorine Pesticides from Natural Waters and Sediments

Abstract

This study aims to evaluate different procedures for the extraction of organochlorine pesticides (OCP's) from natural waters and sediments. In the case of extraction from water, a C18 disk solid-phase extraction method was employed. Recovery experiments in the range of 40 to 200 ng/l with selected organochlorine compounds resulted in average recoveries between 80 and 100%. Four different solvents, hexane, ethyl acetate, acetonitrile and methanol, were tested as eluting agents. Best recoveries were obtained with ethyl acetate and hexane. A comparative study of OCP sediment extraction procedures was performed employing sonication, Soxhlet extraction and shake-flask methods. The capacity of these methods to recover OCP's from a sediment sample fortified at 50 ng/g was evaluated using hexane : acetone (1:1 v/v), hexane: acetone (8:2 v/v), acetonitrile and dichlorometane. The three extraction techniques gave similar results and dichloromethane was the most effective solvent. The optimised methods were applied in the analysis of waters and sediments from the “Aiguamolls de l'Empordà” Nature Park, Girona (Spain).     

Determination of phthalate esters in soil using a quick,easy, cheap,effective, rugged,and safe method followed by GC–MS

A quick, easy, cheap, effective, rugged, and safe procedure was designed to extract pesticide residues from fruits and vegetables with a high percentage of water. It has not been used extensively for the extraction of phthalate esters from sediments, soils, and sludges. In this work, this procedure was combined with gas chromatography with mass spectrometry to determine 16 selected phthalate esters in soil. The extraction efficiency of the samples was improved by ultrasonic extraction and dissolution of the soil samples in ultra‐pure water, which promoted the dispersion of the samples. Furthermore, we have simplified the extraction step and reduced the risk of organic solvent contamination by minimizing the use of organic solvents. Different extraction solvents and clean‐up adsorbents were compared to optimize the procedure. Dichloromethane/n‐hexane (1:1, v/v) and n‐hexane/acetone (1:1, v/v) were selected as the extractants from the six extraction solvents tested. C18/primary secondary amine (1:1, m/m) was selected as the sorbent from the five clean‐up adsorbents tested. The recoveries from the spiked soils ranged from 70.00 to 117.90% with relative standard deviation values of 0.67–4.62%. The proposed approach was satisfactorily applied for the determination of phthalate esters in 12 contaminated soil samples.     

Preconcentration and determination of ultra trace amounts of palladium in water samples by dispersive liquid-liquid microextraction and graphite furnace atomic absorption spectrometry

A highly sensitive, simple and rapid method is presented for the determination of palladium using graphite furnace atomic absorption spectrometry after its separation and preconcentration by dispersive liquid-liquid microextraction. Ultra traces of Pd were extracted and preconcentrated in acidic water samples by using 2-amino-1-cyclohexene-1-dithiocarboxylic acid as a suitable chelating agent, and carbon tetrachloride and acetone as extraction and disperser solvents, respectively. The experimental parameters were optimized in order to enhance the extraction efficiency. After optimizing the extraction conditions and various instrumental parameters, an enhancement factor of 350 was obtained. The analytical curve absorbance vs. concentration was linear over the range 0.02–0.6 µg L^-1 Pd. The detection limit and relative standard deviation were 0.007 µg L^-1 and 4.2%, respectively. The method was successfully applied to the determination of palladium in roadside soil and several aqueous samples.     

Simultaneous Analysis of Herbicide Metribuzin and Quizalofop-p-ethyl Residues in Potato and Soil by GC-ECD

A robust and sensitive method was developed for the simultaneous analysis of metribuzin and quizalofop-p-ethyl residues in potato and soil, based on solid-phase extraction (SPE) coupled to capillary gas chromatography with electron capture detector (GC-ECD). Residues of two herbicides were extracted from potato and soil with acetone and methanol–water, followed by SPE to remove coextractives, before analysis by GC-ECD. SPE procedures were performed on Florisil cartridges (500 mg, 3 mL), the analytes from potato and soil matrix were eluted with petroleum ether-acetic ether (9:1 v/v, 5 mL) and petroleum ether-acetic ether (8:2 v/v, 2 mL), respectively. Limits of quantification of the method were 0.01 mg kg^?1, and the mean recoveries ranged from 72.9 to 109.5% with relative standard deviation ranging from 0.7 to 9.2% at the three spike levels (0.01, 0.1, and 0.5 mg kg^?1). The proposed method was successfully applied to the analysis of metribuzin and quizalofop-p-ethyl residues in potato and soil samples from an experimental field. Direct confirmation of the analytes in real samples was achieved by gas chromatography-mass spectrometry (GC–MS).     

A highly sensitive procedure for determination of ultra trace amounts of molybdenum by graphite furnace atomic absorption spectrometry after dispersive liquid-liquid microextraction

A simple, rapid and sensitive method is developed for selective determination of ultra trace amounts of molybdenum(V?) from different water samples. The method is based on highly efficient separation and pre-concentration of molybdenum(V?) by dispersive liquid-liquid microextraction followed by its determination with graphite furnace atomic absorption spectrometry. Ultra traces of the target ion were extracted and pre-concentrated from acidic water samples by using sodium diethyldithiocarbamate as a suitable chelating agent, and carbon tetrachloride and acetone as extraction and disperser solvents, respectively. After optimizing different parameters, including type and volume of extraction and disperser solvents, pH of test solution, extraction time, volume and concentration of the chelating agent and sample volume, an enrichment factor of 362 was obtained. The linear concentration range, limit of detection and relative standard deviation of the method were evaluated as 0.04–0.8 ng mL^?1, 0.007 ng mL^?1 and 4.5%, respectively. This method was applied successfully to the determination of molybdenum in tap water and wastewater samples.     

Determination of the fungicides vinclozolin and dicloran in soils using ultrasonic extraction coupled with solid-phase microextraction

Solid-phase microextraction (SPME) coupled to ultrasonic extraction was evaluated for extracting trace amounts of two agrochemical fungicides, vinclozolin and dicloran, in soil samples. Extraction was performed following two experimental approaches prior to the submission of the aqueous extracts to SPME-GC analysis. In the first approach, extraction involved sample homogenization with a water solution containing 5% (v/v) acetone and centrifugation prior to fiber extraction. In the second approach, the extraction of the fungicides from the soil samples was conducted using acetone as organic solvent which was then diluted with water to give a 5% (v/v) content. The pesticides were isolated with fused silica fiber coating with 85 μm polyacrylate. Parameters that affect both the extraction of the fungicides by the soil samples and the trapping of the analytes by the fiber were investigated and their impact on the SPME-GC-MS was studied. The procedures with respect to repeatability and limits of detection were evaluated by soil spiked with both analytes. Repeatability was between 5.6 and 14.2% and the limits of detection were 2-13 ng g⁻¹. The efficiency of acetone/SPME was generally better than that for water/SPME procedure showing good linearity (R²>0.99) with coefficient variations below 9%, recoveries higher than 91% and limits of detection between 2 and 3 ng g⁻¹. Finally, the recoveries obtained with acetone/SPME procedure were compared with the conventional liquid-liquid extraction using real soil samples. The acetone/SPME method was shown to be an inexpensive, fast and simple preparation method for the determination of target analytes at low nanogram per gram levels in soils.     

Analysis of aged sulfadiazine residues in soils using microwave extraction and liquid chromatography tandem mass spectrometry

An efficient extraction of sulfadiazine residues from soils is difficult, as sulfadiazine is known to form quickly sequestering residues. The objective of this study was to optimize an exhaustive extraction for aged residues of sulfadiazine and its two major metabolites, N-acetylsulfadiazine and 4-hydroxysulfadiazine, from soil. For this purpose two representative used agricultural soils (Luvisol, Cambisol) were blended with manure derived from [¹⁴C]sulfadiazine-treated pigs and incubated at 10 °C in the laboratory. After different extraction tests with various solvent mixtures (two- to four-component mixtures with water, methanol, acetonitrile, acetone, and/or ethyl acetate), different pH values (pH 4 and 9), and extraction temperatures (up to 200 °C), soil extracts were measured by liquid scintillation counting and liquid chromatography coupled to tandem mass spectrometry. With respect to sulfadiazine yields, stability of soil extracts, and the amount of coextracted matrix, a microwave extraction of soil (15 min, 150 °C) using acetonitrile/water 1:4 (v/v) is the method of choice for the exhaustive extraction of aged sulfadiazine residues from soils.     

Pressurized liquid extraction of polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans and coplanar polychlorinated biphenyls from contaminated soil

Extraction solvents for pressurized liquid extraction (PLE) used to extract polychlorinated dibenzo-p-dioxins, polychlorinated dibenzofurans (PCDD/PCDFs), and coplanar polychlorinated biphenyls (Co-PCBs) from contaminated soil were investigated. The PCDD/PCDFs and Co-PCBs in Certified Reference Material: CRM 0422 (Forest soil) were extracted using toluene, n-hexane, acetone, acetone/toluene and acetone/n-hexane (1:1, v/v). Soxhlet extraction was the reference method. Results demonstrated that PLE using mixed solvents produced better analyte recoveries than the single solvents. However, these results were lower than those for Soxhlet extraction. Additional extraction cycles using mixed solvents achieved better recovery results. Mixed solvents and several extraction cycles were necessary for satisfactory extraction of more tightly bound PCDD/PCDFs and Co-PCBs from soil.     

Pyrethroid soil extraction,properties of mixed solvents and time profiles using GC/MS-NICI analysis

Ultrasonic extraction was used to develop a suitable binary solvent system for the analysis of synthetic pyrethroid pesticides and mirex on soil. The analysis was carried out by gas chromatography with negative ion chemical ionization mass spectrometry (GC/MS-NICI). In the initial experiments, accurately weighed soil samples were spiked with a mixture of standard solution pyrethroids and mirex and shaken for 24?h to ensure homogeneity, then extracted with solvent. The extracts were evaporated to dryness before the volumetric internal standard was added.

The binary solvents used in this study were various mixtures of hexane?:?acetone, hexane?:?dichloromethane (DCM), isooctane?:?acetone and isooctane?:?dichloromethane, representing different classes of polarity. The recoveries of all pyrethroids and mirex were satisfactory over three solvent systems: hexane?:?acetone, hexane?:?DCM and isooctane?:?acetone, but results of isooctane?:?DCM produced low recoveries. The average recovery increased with the extraction time, but the increase was not statistically significant. A 30-min optimum extraction was deemed sufficient for recovering pyrethroids from soil. After 30?min, extraction decreased owing to the re-distribution of the analyte on the soil matrix.     

Determination of ametoctradin in plant residues and environmental samples by HPLC with an UV detector

The study deals with the development of a method for the determination of ametoctradin by HPLC with UV detection. Samples were extracted with aqueous acetone and then purified by distribution between immiscible solvents and also on solid-phase extraction cartridges. The procedure was tested in the determination of ametoctradin in water in the range 0.001–0.01 mg/L, in soil, potato vine and potato tubers, salad, onion, cucumber, tomatoes, carrots, grapes, and grape juice in the range from 0.005 to 0.1 mg/kg, depending on the matrix. The average recoveries were 78?92% with RSD < 0.08%. The proposed procedure is applicable to the determination of ametoctradin in environmental samples and plant residues.     

Multi-residue method for trace pesticide analysis in soils by LC-QQQ-MS/MS and its application to real samples

ABSTRACT

A method for the simultaneous determination of 30 pesticides residues in soil was developed and validated. Among the studied agrochemicals, there are herbicides (auxines, sulfonylureas, fops, imidazolinones), fungicides (azoles) and insecticides (organophosphorus) widely used in extensive agricultural activities in Uruguay. Five methods with different extraction times, type and amount of solvent, as well as the possibility of a clean-up step were compared in terms of percentage of recovery and repeatability. The final method was based on the extraction of the pesticides’ residues from soil using two successive solvent extraction steps. First, the soil was extracted with methanol in an orbital shaker for 4 h. Secondly, the solid residue was re-extracted overnight with ultrapure water. The methanolic extract was concentrated under vacuum, whereas the aqueous solution was passed through an OASIS HLB® cartridge, eluted with an appropriate solvent and concentrated under nitrogen stream. Both extracts were finally combined and analysed by LC-QQQ-MS/MS using the Document SANTE/11,945/2015 criteria. Recovery percentages at 1 and 10 μg kg^?1 for the studied compounds were in the range 70106% with relative standard deviations below 19 %. The quantification was performed using matrix-matched calibration curves as some compounds presented very strong signal suppression. Residuals of the matrix-matched calibration curves were below 20% for all the validated analytes. The quantification limit was1 μg kg^?1. The method also allows the screening of 11 pesticides in soil. Sixty-five real samples collected from regions where the use of pesticides is intensive were analysed. Quinclorac, tebuconazole, penoxsulam and clomazone were the most frequently pesticides detected.     

Polarographische Bestimmung von Spuren von Carbonylverbindungen in organischen Lösungsmitteln

Traces of formaldehyde, acetaldehyde and acetone in organic solvents are determined polarographically as semicarbazones. Solvents miscible with water are measured directly in aqueous buffer solution of semicarbazide, while from those nonmiscible with water the carbonyl compounds are first extracted with a solution of semicarbazide. The polarography of semicarbazones as an analytical method is considerably more sensitive than the direct polarography of aldehydes in a neutral or alkaline medium: in 1 ml samples of solvents, formaldehyde, acetaldehyde and acetone can be determined in concentrations of about 10^?4%. The method also permits the determination of formaldehyde, acetaldehyde and acetone simultaneously.     

An optimized method for the determination of volatile and semi-volatile aldehydes and ketones in ambient particulate matter

A method has been developed to measure aldehydes and ketones associated with atmospheric particles. Carbonyl compounds from particulate material collected on Teflon-coated glass-fiber filters were simultaneously extracted and derivatized with an appropriate 2,4-dinitrophenylhydrazine (2,4-DNPH) solution. The efficiency of this procedure utilizing various 2,4-DNPH concentrations and solvent compositions was studied for 13 carbonyl compounds of atmospheric importance. These include formaldehyde, acetaldehyde, acetone, dicarbonyls such as glyoxal and methylglyoxal, and biogenic carbonyls such as pinonaldehyde and nopinone. An extraction solution containing 3 × 10^?2 M 2,4-DNPH, in 60% acetonitrile/40% water, and pH 3 was most efficient in extracting and derivatizing these aldehydes and ketones (83-100% recovery). Improved sample enrichment and 2,4-DNPH purification methods were developed that afforded detection limits of 0.009-5.6 ng m^?3. The relative standard deviation for replicate analyses were 1.9-10.1%. Carbonyl compounds in ambient particulate samples were quantified during a recent field study. Median values for nine carbonyl species ranged from 0.01-33.9 ng m^?3 during the study.     

A Review of the Extraction of Herbicide Residues from Aged Saskatchewan Field Soils

Abstract

Polar solvents based on aqueous methanol and aqueous acetonitrile are good extractants of herbicides from Saskatchewan field soils that had received treatments of the individual chemicals 6 to 17 months previously. The addition of small amounts of acetic acid or ammonium hydroxide to aqueous acetonitrile resulted in greater recovery of most herbicides. In general, 50 ml of the extraction solvent were added to 20 g of soil and the soils were then initially extracted for 1-hr on a wrist-action shaker and then allowed to stand overnight before being shaken for a further 1-hr period.     

Optimization of the extraction process of flavonoids from Trollius ledebouri with natural deep eutectic solvents

In recent years, natural deep eutectic solvents have been favored greatly due to their environment friendly, mild biological toxicity and simple biodegradability. Natural deep eutectic solvents gradually applied for the extracting bioactive compounds from natural products efficiently. In this study, 20 natural deep eutectic solvents were prepared and their physical and chemical properties were tested. The ultrasonic-assisted extraction method was used to extract flavonoids from Trollius ledebouri and high-performance liquid chromatography-ultraviolet was applied to examine two main bioactive flavonoids (orientin and vitexin). Compared with traditional solvents (water and 60% ethanol solution), natural deep eutectic solvents composed of L(-)-proline and levulinic acid (molar ratio 1:2) show a super extraction efficiency. On this basis, the response surface method was used to optimize the extraction temperature, extraction time, water contents, and solid–liquid ratio. As a consequence, the extraction temperature 60℃, extraction time 18 min, water content 14% (v/v), and the solid–liquid ratio 48 mL·g⁻¹ were chosen as the best extraction process. This study shows that natural deep eutectic solvents can effectively extract flavonoids from T. ledebouri, laying a foundation for the further application of natural deep eutectic solvents to extract bioactive compounds from natural products.     

Simultaneous extraction and determination of fluoroquinolones,tetracyclines and sulfonamides antibiotics in soils using optimised solid phase extraction chromatography-tandem mass spectrometry

An analytical method was developed for the simultaneous extraction and determination of 18 fluoroquinolones (FQs), tetracyclines (TCs) and sulfonamides (SAs) antibiotics from soils using solid phase extraction and liquid chromatography-tandem mass spectrometry. The soils were extracted by different solvents with the help of mechanical shaking and ultrasonic treatment at 59?kHz, followed by a strong anion exchange (SAX) cartridge to clean up soil samples and a hydrophilic lipophilic balance (HLB) cartridge as enrichment. The method was evaluated by testing the following variables: extraction solvents, the type of SPE cartridges, solvent volumes, initial spiking levels and soil types (silty clay loam and clay loam soils). The soil extraction method was validated using these two types of soils, representing two typical agricultural soils in northern China. For 2?g soil, the extraction steps with the mixture of potassium phosphate buffer and acetonitrile (ACN) (1/1, v/v, pH 3.2) provided satisfactory recoveries. In the clay loam soil, the recoveries of all the compounds were from 56% to 89% at the spiking level of 50?µg?kg^?1 soil, and from 69% to 97% at the spiking level of 200?µg?kg^?1 soil, respectively. Recoveries in silty clay loam soil were similar to that in clay loam. The method was successfully employed using soil samples collected from a farmland and afforestion area irrigated with sewage in northern China. The result indicates that trace antibiotics in sewage may accumulate in soil irrigated by river water containing sewage.     

Determination of strobilurin fungicides in cotton seed by combination of acetonitrile extraction and dispersive liquid−liquid microextraction coupled with gas chromatography

The simultaneous determination of four strobilurin fungicides (picoxystrobin, kresoxim‐methyl, trifloxystrobin, and azoxystrobin) in cotton seed by combining acetonitrile extraction and dispersive liquid?liquid microextraction was developed prior to GC with electron capture detection. Several factors, including the type and volume of the extraction and dispersive solvents, extraction condition and time, and salt addition, were optimized. The analytes were extracted with acetonitrile from cotton seed and the clean‐up was carried out by primary secondary amine. Afterwards, 60 μL of n‐hexane/toluene (1:1, v/v) with a lower density than water was mixed with 1 mL of the acetonitrile extract, then the mixture was injected into 7 mL of distilled water. A 0.1 mL pipette was used to collect a few microliters of n‐hexane/toluene from the top of the aqueous solution. The enrichment factors of the analytes ranged from 36 to 67. The LODs were in the range of 0.1 × 10^?3?2 × 10^?3 mg/kg. The relative recoveries varied from 87.7 to 95.2% with RSDs of 4.1?8.5% for the four fungicides. The good performance of the method, compared with the conventional pretreatments, has demonstrated it is suitable for determining low concentrations of strobilurin fungicide residues in cotton seed.     

Extraction and percolation of PAEs from chemical protective gloves

Phthalates (PAEs) have high solubility in polymers and are added as plasticisers to increase the flexibility and plasticity of polymeric materials. In this study, methanol, hexane, ethyl ether and acetone were used for the extraction of PAEs from chemical protective gloves at temperatures of 20–80 °C. DEHP (di-2-ethylhexyl phthalate) and DBP (di-n-butyl phthalate) were extracted from neoprene, nitrile and PVC glove samples using the above four solvents. The extraction level of DEHP from the glove samples was proportional to the Log K_ow values of the extraction solvents. This result implied that PAEs were more soluble in non-polar solvents and were likely to be extracted from the gloves. Increasing the extraction temperature resulted in a higher extraction of DBP and DEHP from the gloves. In the ASTM F739 permeation method, the aromatic solvents permeated through the glove samples and dissolved DEHP. If the permeant and DEHP had similar solubility parameters, DEHP was likely to be leached from the gloves. The modelling results indicated that the permeation behaviour of the organic solvent in the PVC glove was non-Fickian diffusion. It was speculated that the plasticiser increased the diffusion coefficients of the permeants in the PVC gloves. This study suggested that the potential dissolution and leaching of PAEs from chemical protective gloves should be a concern for workers who handle organic solvents.