A catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances

A simple and fast catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in natural samples containing high concentrations of humic substances has been developed. The procedure for chromium determination in the presence of DTPA and nitrates was employed as the initial method. In order to enhance the selectivity vs. Cr(III) the measurements were performed at 40°C. Interference from dissolved organic matter such as humic and fulvic acids was drastically decreased by adding Amberlite XAD-7 resin to the voltammetric cell before the deaeration step. The whole procedure was applied to a single cell, which allowed monitoring of the voltammetric scan. Optimum conditions for removing humic and fulvic acids due to their adsorption on XAD-7 resin were evaluated. The use of XAD-7 resin also minimize interferences from various cationic, anionic, and nonionic surfactants. The calibration graph for Cr(VI) for an accumulation time of 30 s was linear in the range 5 × 10⁻¹⁰ to 5 × 10⁻⁸ mol L⁻¹. The relative standard deviation for determination of Cr(VI) at a concentration of 1 × 10⁻⁸ mol L⁻¹ was 3.5% (n = 5). The detection limit estimated from 3 times the standard deviation for low Cr(VI) concentrations and an accumulation time of 30 s was about 1.3 × 10⁻¹⁰ mol L⁻¹. The proposed method was successfully applied to Cr(VI) determination at trace levels in soil samples.     

Determination of Cr(VI) in the Presence of Complexing Agents and Humic Substances by Catalytic Stripping Voltammetry

The voltammetric method of Cr(VI) determination in a flow system is proposed. Determinations can be carried out in the simultaneous presence of an excess of Cr(III), complexing agents, humic substances and surfactants. The method is based on the combination of a selective accumulation of the product of Cr(VI) reduction to the metallic state and a very sensitive voltammetric method of chromium determination in the presence of DTPA and nitrates. The calibration graph is linear from 1×10^?9 to 5×10^?8 mol L^?1 for accumulation time of 30 s. The relative standard deviation is 5.2% (n=5) for Cr(VI) concentration 1×10^?8 mol L^?1. The influence of humic and fulvic acids, complexing agents and surfactants on Cr(VI) and the interfering Cr(III) signal is presented. The method was applied to Cr(VI) determination in certified reference material, soil sample, natural water sample and EDTA extracts from soil certified reference material.     

On-line preconcentration and speciation analysis of Cr(III) and Cr(VI) using baker's yeast cells immobilised on controlled pore glass

A study was undertaken to evaluate Saccharomyces cerevisiae as a substrate for the biosorption of Cr(III) and Cr(VI) aiming to the selective determination of these species in aqueous solutions. The yeast cells were covalently immobilised on controlled pore glass (CPG), packed in a minicolumn and incorporated in an on-line flow injection system. The effect of chemical and physical variables affecting the biosorption process was tested in order to select the optimal analytical conditions for the Cr retention by S. cerevisiae. Cr(III) was retained by the immobilised cells and Cr(VI) were retained by CPG. The speciation was possible by selective and sequential elution of Cr(III) with 0.05 mol L⁻¹ HCl and 2.0 mol L⁻¹ HNO₃ for Cr(VI). The influence of some concomitant ions up to 20 mg L⁻¹ was also tested. Quantitative determinations of Cr were carried out by means of inductively coupled plasma optical emission spectrometry (ICP OES). Preconcentration factors of 12 were achieved for Cr(III) and 5 for Cr(VI) when 1.7 mL of sample were processed reaching detection limits of 0.45 for Cr(III) and 1.5 μg L⁻¹ for Cr(VI). The speciation of inorganic Cr in different kinds of natural waters was performed following the proposed method. Spiked water samples were also analysed and the recoveries were in all cases between 81 and 103%.     

Application of Voltammetric Method of Total Chromium Determination in the Presence of Cupferron for Selective Determination of Cr(VI) in Water Samples

A voltammetric method of Cr(VI) determination in a flow system based on the combination of selective accumulation of the product of Cr(VI) reduction on hanging mercury drop electrode and a very sensitive method of chromium determination in the presence of cupferron previously described is proposed. The calibration graphs were linear from 3 × 10⁻⁹ to 3 × 10⁻⁸ and from 5 × 10⁻¹⁰ to 5 × 10⁻⁹ mol L⁻¹ for accumulation times of 120 and 600 s, respectively. The detection limit for the accumulation time of 600 s was 9 × 10⁻¹¹ mol L⁻¹. The relative standard deviation was 5.1% (n = 5) for Cr(VI) concentration 1 × 10⁻⁸ mol L⁻¹ and the accumulation time of 120 s. The influence of foreign ions commonly present in water samples is presented. The validation of the method was made by studying the recovery of Cr(VI) from spiked natural water samples.     

Simultaneous, sensitive and selective on-line chemiluminescence determination of Cr(III) and Cr(VI) by capillary electrophoresis

A novel in-capillary reduction and capillary electrophoretic (CE)-chemiluminescence (CL) method was developed for the sensitive and selective determination of chromium(III) and chromium(VI). The proposed method was based on the in-capillary reduction of Cr(VI) with acidic H₂O₂ to form Cr(III) using the zone-passing technique and chemiluminescence detection of Cr(III). The sample [Cr³⁺ and CrO₄²⁻], hydrochloric acid, and H₂O₂ (reductant) solution segments were injected for specified periods of time in this order from the anodic end of a capillary, followed by application of an appropriate running voltage between both ends. As both chromium species have opposite charges, Cr³⁺ migrates to the cathode while CrO₄²⁻ ion, moving oppositely to the anode, reacts with acidic H₂O_2, resulted in formation of Cr³⁺. Based on the migration time difference of both Cr³⁺ ions, they were separated by zone electrophoresis. Running buffer was composed of 0.02 mol l⁻¹ HAc-NaAc (pH 4.7) with 1×10⁻³ mol l⁻¹ EDTA. Parameters affecting CE-CL separation and detection, such as reductant concentration, mixing mode of the analytes with CL reagent, CL reaction reagent pH and concentration, stability of luminol-hydrogen peroxide mixed solution were optimized. The limits of detection for chromium(III) and chromium(VI) (3σ) were 6×10⁻¹³ mol l⁻¹ (mass concentration 12 zmol) and 8×10⁻¹² mol l⁻¹ (160 zmol), respectively. This method offered potential advantages of simplicity, sensitivity, selectivity and applicability to the determination of Cr(III) and Cr(VI) in environmental water.     

A novel flow injection chemiluminescence determination of Cr(VI) with Dichlorotris(1,10-phenanthroline)ruthenium(II)

A selective novel reverse flow injection system with chemiluminescence detection (rFI-CL) for the determination of Cr(VI) in presence of Cr(III) with Dichlorotris (1,10-phenanthroline)ruthenium(II), (Ru(phen)₃Cl₂), is described in this work. This new method is based on the oxidation capacity of Cr(VI) in H₂SO₄ media. First, the Ruthenium(II) complex is oxidized to Ruthenium(III) complex by Cr(VI) and afterwards it is reduced to the excited state of the Ruthenium(II) complex by a sodium oxalate solution, emitting light inside the detector. The intensity of chemiluminescence (CL) is proportional to the concentration of Cr(VI) and, under optimum conditions, it can be determined over the range of 3-300 μg L⁻¹ with a detection limit of 0.9 μg L⁻¹. The RSD was 8.4% and 1.5% at 5 and 50 μg L⁻¹, respectively. For the rFI-CL method various analytical parameters were optimized: flow rate (1 mL min⁻¹), H₂SO₄ carrier concentration (20% w/V), Ru(phen)₃Cl₂ concentration (5 mM) and sodium oxalate concentration (0.1 M). The effect of Cr(III), Fe(III), Al(III), Cd(II), Zn(II), Hg(II), Pb(II), Ca(II) and Mg(II), was studied. The method is highly sensitive and selective, allowing a fast, on-line determination of Cr(VI) in the presence of Cr(III). Finally, the method was tested in four different water samples (tap, reservoir, well and mineral), with good recovery percentage.     

Hybrid mesoporous materials for on-line preconcentration of Cr(VI) followed by one-step scheme for elution and colorimetric determination at ultratrace levels

An hybrid mesoporous material synthesised in our laboratories for solid phase extraction (SPE) in flow through systems has been used for analytical purposes. The solid was obtained from mesoporous silica MCM-41 functionalized with 3-aminopropyltriethoxy silane by Sol-Gel methodology. In order to exploit the large sorption capacity of the material together with the possibility of modeling it for anions retention, a microcolumn (MC) filled with the solid was inserted in a flow system for preconcentration of Cr(VI) and its determination at ultratrace levels in natural waters. The analytical methodology involved a reverse flow injection system (rFI) holding a MC filled with the solid for the analyte extraction. Elution and colorimetric detection were carried out with 1-5 diphenylcarbazide (DPC) in sulfuric acid. DPC produced the reduction of Cr(VI) to Cr(III) together with the generation of a cationic red complex between Cr(III) and 1-5 diphenylcarbazone which was easily eluted and detected with a visible spectrophotometer. Moreover, the filling material got ready for the next sample loading remaining unspoiled for more than 300 cycles.The effect of several variables on the analytical signal as well as the influence of cationic and anionic interferences were discussed. Particular attention was given to sulfuric acid interference since it is the required media for the complex generation.Under optimal conditions, 99.8% of Cr(VI) recovery was obtained for a preconcentration time of 120 s (sample and DPC flow rates = 1 mL min⁻¹) and an elution volume of 250 μL. The limit of detection (3 s) was found to be 0.09 μg L⁻¹ Cr(VI) with a relative standard deviation (n = 10, 3 μg L⁻¹) of 1.8.Since no Cr(III) was retained by the solid material and Cr(VI) was completely adsorbed, electrothermal atomic absorption spectrometry (ET AAS) determinations of Cr(III) were also performed by simply measuring its concentration at the end of the microcolumn after Cr(VI) retention by the mesoporous solid.Applications to the determination of Cr(VI) and Cr(III) in natural waters and the validation of the methodology were also studied.     

Preconcentration and speciation of chromium using a melamine based polymeric sequestering succinic acid resin: its application for Cr(VI) and Cr(III) determination in wastewater

A new melamine based polymeric sequestering resin was prepared for preconcentration and separation of hexavalent chromium from water, and its sequestering action was investigated. The water-insoluble, cross-linked sequestering resin was formed by reaction with bromosuccinic acid and cross-linking of melamine. The active sequestering group on the resin is NH-(Succinic acid) or salt thereof. The resulting chelating resin was characterized by infrared spectra. The newly prepared resin quantitatively retained Cr(VI) at pH 2.0-4.0 when the flow rate was maintained between 1 and 5 ml min⁻¹. The retained Cr(VI) was instantaneously eluted with 25 ml of 0.1 M NaOH. The chromium species were determined by a flame atomic absorption spectrometer. The limits of detection for Cr(VI) and Cr(III) were found to be 5.3 and 4.2 μg l⁻¹, respectively. The precision and accuracy of the proposed procedure was checked by the use synthetic and reference steel samples. The established preconcentration method was successfully applied to the determination and selective separation of Cr(VI) in electroplating industry wastewater. Total concentrations determined by the spectrophotometric method (110.3±0.6 g l⁻¹ Cr(VI) and 1.2±0.3 g l⁻¹ Cr(III)) are compared with those found by FAAS and the obtained results (110.4±1.8 g l⁻¹ Cr(VI) and 1.4±0.5 g l⁻¹ Cr(III)) show good agreement.     

Application of double-spike isotope dilution for the accurate determination of Cr(III), Cr(VI) and total Cr in yeast

A method is presented for the simultaneous determination of Cr(III) and Cr(VI) in yeast using species-specific double-spike isotope dilution (SSDSID) with anion-exchange liquid chromatography (LC) separation and sector field inductively coupled plasma mass spectrometric (SF-ICP-MS) detection. Total Cr is quantitated using ID SF-ICP-MS. Samples were digested on a hot plate at 95±2 °C for 6 h in an alkaline solution of 0.5 M NaOH and 0.28 M Na₂CO₃ for the determination of Cr(III) and Cr(VI), whereas microwave-assisted decomposition with HNO₃ and H₂O₂ was used for the determination of total Cr. Concentrations of 2,014±16, 1,952±103 and 76±48 mg kg⁻¹ (one standard deviation, n=4, 3, 3), respectively were obtained for total Cr, Cr(III) and Cr(VI) in the yeast sample. Significant oxidation of Cr(III) to Cr(VI) (24.2±7.6% Cr(III) oxidized, n=3) and reduction of Cr(VI) to Cr(III) (37.6±6.5% Cr(VI) reduced, n=3 ) occurred during alkaline extraction and subsequent chromatographic separation at pH 7. Despite this significant bidirectional redox transformation, quantitative recoveries for both Cr(III) and Cr(VI) were achieved using the SSDSID method. In addition, mass balance between total Cr and the sum of Cr(III) and Cr(VI) concentrations was achieved. Method detection limits of 0.3, 2 and 30 mg kg⁻¹ were obtained for total Cr, Cr(VI) and Cr(III), respectively, based on a 0.2-g sub-sample.     

Chromium(III) ion selective electrode based on glyoxal bis(2-hydroxyanil)

A poly(vinyl chloride) membrane based on glyoxal bis(2-hydroxyanil) as membrane carrier was prepared and investigated as a Cr(III)-selective electrode. The electrode has a linear dynamic range of 3.0×10⁻⁶-1.0×10⁻² mol l⁻¹, with a Nernstian slope of 19.8±0.5 mV per decade and a detection limit of 6.3×10⁻⁷ mol l⁻¹. It has a fast response time of <20 s and can be used for at least 3 months without any considerable divergence in potential. The proposed electrode revealed good sensitivities for Cr(III) over a wide variety of metal ions and could be used in a pH range of 2.7-6.5. Above all, the membrane sensor has been used very successfully for the analysis of some food materials and alloys for the determination of Cr(III) ion.     

Ultraselective and Sensitive Determination of Cr(VI) in the Presence of a High Excess of Cr(III) in Natural Waters with a Complicated Matrix

In the present work, the catalytic adsorptive stripping voltammetric procedure for trace determination of Cr(VI) in the presence of a high excess of Cr(III) in natural waters with a complicated matrix has been developed. The influence from potentially interfering substances such as organic matter was successfully eliminated by exploiting adsorptive properties of polymeric resin. The detection limit estimated from 3 times the standard deviation for a low Cr(VI) concentration in the simultaneous presence of a 2×10³ fold excess of Cr(III), 50 mg L^?1 surfactants, 50 mg L^?1 humic substances and the accumulation time of 30 s was about 5.3×10^?10 mol L^?1.     

Voltammetric determination of isoprenaline in pharmaceutical preparations using a copper(II) hexacyanoferrate(III) modified carbon paste electrode

The electroanalytical determination of isoprenaline in pharmaceutical preparations of a homemade carbon paste electrode modified with copper(II) hexacyanoferrate(III) (CuHCF) was studied by cyclic voltammetry. Several parameters were studied for the optimization of the sensor such as electrode composition, electrolytic solution, pH effect, potential scan rate and interferences in potential. The optimum conditions were found in an electrode composition (in mass) of 15% CuHCF, 60% graphite and 25% mineral oil in 0.5 mol l⁻¹ acetate buffer solution at pH 6.0. The analytical curve for isoprenaline was linear in the concentration range from 1.96×10⁻⁴ to 1.07×10⁻³ mol l⁻¹ with a detection limit of 8.0×10⁻⁵ mol l⁻¹. The relative standard deviation was 1.2% for 1.96×10⁻⁴ mol l⁻¹ isoprenaline solution (n=5). The procedure was successfully applied to the determination of isoprenaline in pharmaceutical preparations; the CuHCF modified carbon paste electrode gave comparable results to those results obtained using a UV spectrophotometric method.     

Flow injection solid phase extraction electrothermal atomic absorption spectrometry for the determination of Cr(VI) by selective separation and preconcentration on a lab-made hybrid mesoporous solid microcolumn

A lab-made hybrid mesoporous solid was employed in a flow injection solid phase extraction electrothermal atomic absorption spectrometric (FI–SPE–ETAAS) system for the selective retention of Cr(VI). The solid was prepared by co-condensation of sodium tetraethylortosilicate and 3-aminopropyltriethoxysilane by sol–gel methodology and one-pot synthesis and characterized by Fourier transform infrared spectroscopy, X ray diffraction spectroscopy, and scanning electronic microscopy. Adsorption capacities at different pH values of both, Cr(VI) and Cr(III), were also measured in order to obtain the optimum retention for Cr(VI) with no interference of Cr(III). The maximum capacity of adsorption (4.35 mmol g^− 1) was observed for pH values between 2–3, whilst Cr(III) was found to remain in solution (adsorption capacity = 0.007 mmol g^− 1). Then, a microcolumn (bed volume: 7.9 µL) was filled with the solid and inserted in the FI–ETAAS system for analytical purposes. Since the analyte was strongly retained by the filling in the anionic form, 0.1 mol L^− 1 hydroxylammonium chloride in 1 mol L^− 1 hydrochloric acid was selected as eluent due to its redox characteristics. In this way, the sorbed Cr(VI) was easily released in the cationic form. The enrichment factor (EF) was found as a compromise between sensitivity and sample throughput and a value of 27 was obtained under optimized conditions: pH 2, sample loading 2 mL min^− 1 (60 s), elution flow rate 0.5 ml min^− 1 (eluent volume: 75 μL).     

Determination of Cr(VI) by Catalytic Adsorptive Stripping Voltammetry with Application of Nitrilotriacetic Acid as a Masking Agent

A selective and sensitive method for determination of traces of Cr(VI) in the presence of a large excess of Cr(III) by differential pulse catalytic adsorptive stripping voltammetry is presented. For minimization of Cr(III) interference nitrilotriacetic acid was used as a masking agent. The determinations were performed in a flow system. The calibration plot was linear from 1×10⁻¹⁰ to 1×10⁻⁸ mol L⁻¹ for accumulation time 60 s. The relative standard deviation for 3×10⁻⁹ mol L⁻¹ Cr(VI) was 4.1% (n=5). The detection limit for an accumulation time of 60 s was 4×10⁻¹¹ mol L⁻¹. The influence of common foreign ions is also presented. The performance of the method was verified by analysis of certified reference material for Cr(VI) and comparing the results of analyses of natural water samples with those obtained by another accepted electrochemical method.     

Determination of hexavalent chromium (Cr(VI)) in plastics using organic-assisted alkaline extraction

An organic-assisted alkaline extraction method was developed for the determination of hexavalent chromium (Cr(VI)) in plastics. The solubilization of polymer as a pre-step of the alkaline extraction provided good extraction efficiency of Cr(VI) from the sample. The optimization of the experimental conditions affecting the extraction and UV–vis spectrophotometric analysis was accomplished by evaluating the recovery rate of Cr(VI) through the analysis of Cr(VI) in in-house polymer reference materials (RMs). With the proposed method, most of the Cr(VI) in polymers was released within a short extraction time of 30 min and the Cr(III)-DPCO complex can be kept stable for 24 h. The heating for the extraction of the Cr(VI) was not necessary. The optimal pH of the final solution was fixed at 2.0. The proposed extraction method was applied successfully for the determination of Cr(III) and Cr(VI) in spiked samples. The practical applicability of this new method was evaluated through the analysis of Cr(VI) in in-house polymer RMs. The good linearity was demonstrated at desired concentrations of the range 0–3.3 mg L⁻¹. The detection limits were quite low, varying from 0.0061 to 0.0285 mg L⁻¹. The recovery of Cr(VI) was between 97 and 106%, and the relative standard deviation (R.S.D.) was below 6%.     

Flow-injection analysis of two fluoquinolones by the sensitizing effect of terbium(III) on chemiluminescence of the potassium permanganate-sodium sulfite system

A simple, rapid and sensitive method for the determination of two fluoquinolones (FQs), enoxacin (ENX) and ofloxacin (OFLX) is described by using flow injection analysis with potassium permanganate-sodium sulfite chemiluminescence detection. The calibration graphs for ENX and OFLX are linear in the range of 8.0×10⁻¹⁰-1.0×10⁻⁵ and 1.0×10⁻⁹-1.0×10⁻⁶ mol l⁻¹, respectively. The 3σ limits of detection are 2.4×10⁻¹⁰ mol l⁻¹ for ENX and 5.6×10⁻¹⁰ mol l⁻¹ for OFLX. The method is applied satisfactorily to the determination of the two FQs in dosage form and urine sample. The possible mechanism is also proposed.     

Simultaneous determination of lead(II) and cadmium(II) at a diacetyldioxime modified carbon paste electrode by differential pulse stripping voltammetry

A simple and effective chemically modified carbon paste electrode (CMCPE) for the simultaneous determination of lead(II) and cadmium(II) was developed in this work. The electrode was prepared by the addition of diacetyldioxime into a carbon paste mixture. Pb²⁺ and Cd²⁺ were preconcentrated on the surface of the modified electrode by complexing with diacetyldioxime and reduced at a negative potential (−1.10 V). Then the reduced products were oxidized by differential pulse stripping. The fact that two stripping peaks appeared on the voltammograms at the potentials of −0.65 V (Cd²⁺) and −0.91 V (Pb²⁺) demonstrates the possibility of simultaneous determination of Pb²⁺ and Cd²⁺. Under the optimized working conditions, calibration graphs were linear in the concentration ranges of 1.0×10⁻⁷-1.5×10⁻⁵ mol l⁻¹ (Pb²⁺) and 2.5×10⁻⁷-2.5×10⁻⁵ mol l⁻¹ (Cd²⁺), respectively. For 5 min preconcentration, detection limits of 1×10⁻⁸ mol l⁻¹ (Pb²⁺) and 4×10⁻⁸ mol l⁻¹ (Cd²⁺) were obtained at the signal noise ratio (SNR) of 3. To evaluate the reproducibility of the newly developed electrode, the measurements of 5×10⁻⁷ mol l⁻¹ Pb²⁺ and Cd²⁺ were parallel carried out for six times at different electrodes and the relative standard deviations were 2.9% (Pb²⁺) and 3.2% (Cd²⁺), respectively. Interferences by some metals were investigated. Only Ni²⁺ and Hg²⁺ apparently affected the peak currents of Pb²⁺ and Cd²⁺. The diacetyldioxime modified carbon paste electrode was applied to the determination of Pb²⁺ and Cd²⁺ in water samples. The results indicate that this electrode is sensitive and effective for the simultaneous determination of Pb²⁺ and Cd²⁺.     

Selective voltammetric determination of chromium (VI) with DTPA and nitrate

A voltammetric determination of Cr(VI) in a flow system is described based on the selective accumulation of the reduction product of Cr(VI) on an HMDE, its complexation with DTPA and subsequent reduction of the complex in presence of nitrate. The calibration graphs were linear up to 100 and 5 nmol/L for deposition times 120 and 600 s, respectively. The relative standard deviation was 2.8% (n = 5) for Cr(VI) concentrations of 5 × 10^–8 mol/L. The detection limits (3 σ) for Cr(VI) were 1.0 and 0.12 nmol/L at deposition times of 120 and 600 s, respectively. Typical interferences derived from real water samples are discussed. The method has been applied for the determination of Cr(VI) in spiked natural water samples. Received: 18 June 1998 / Revised: 28 September 1998 / Accepted: 5 October 1998     

Sensitive assay for oxygen solubility in molten alkali metal carbonates by indirect flame atomic absorption spectrometric Cr(VI) determination

A precise and accurate indirect analytical method for the assessment of O₂ solubility in molten (Li_0.62K_0.38)₂CO₃ and (Li_0.52Na_0.48)₂CO₃ is described. The method is based on the oxidation of Cr₂(SO₄)₃ (added in excess to the melt) by the oxygenate species, which are formed inside the melt when it is in contact with oxygen gas, and subsequent determination of trace amount of Cr(VI) in withdrawn frozen melts by flame atomic absorption spectrometry (FAAS). The samples (1.0-2.0 g) are dissolved in dilute hydrochloric acid at room temperature. The speciation of Cr(VI) is carried out by complexation with ammonium pyrrolidine dithiocarbamate (APDC), followed by extraction into methyl isobutyl ketone (MIBK), which is introduced directly into the flame. Optimisation of the flame composition provided maximum Cr signal in organic phase under lean acetylene-air flame. The separation and preconcentration parameters such as sample volume/extractant volume ratio, pH sample solution, chelating concentration and extraction time are evaluated. Under the optimised conditions Cr(VI) is efficiently separated from Cr(III), which exceeded 200-folds. The results of the analysis of synthetic samples using standards in MIBK medium give rise to recoveries of 98-99%. The Cr(VI) detection limit of 4×10⁻⁶ g L⁻¹ using 12.5-fold preconcentration and relative standard deviation of 1% at the 0.10 mg L⁻¹ level are obtained. The sampling-to-sampling reproducibility was typically 3-5% relative standard deviation. By changing the preconcentration factor and the dilution of the sample melt, it is possible to analyse oxygen concentrations in molten alkali metal carbonates as low as 1.5×10⁻⁹ mol O₂ per gram melt.     

Flow injection direct spectrophotometric assay for the speciation of trace chromium(III) and chromium(VI) using chromotropic acid as chromogenic reagent

A new rapid and sensitive FI assay is reported for the simultaneous direct spectrophotometric determination of trace Cr(VI) and Cr(III) in real samples. The method is based upon the reaction of Cr(VI) with chromotropic acid (CA) in highly acidic medium to form a water-soluble complex (λ_max = 370 nm). Cr(III) reacts with CA only after its on-line oxidation to Cr(VI) by alkaline KIO₄. The determination of each chromium species in the sample was achieved by absorbance differences. The calibration curves were linear over the range 3-4000 μg l⁻¹ and 30-1200 μg l⁻¹ for Cr(VI) and Cr(III), respectively, while the precision close to the quantitation limit was satisfactory in both cases (s_r = 3.0% for Cr(VI) and 4.0% for Cr(III) (n = 10) at 10 and 50 μg l⁻¹ level, respectively). The method developed proved to be adequately selective and sensitive (c_L = 1 and 10 μg l⁻¹ for Cr(VI) and Cr(III), respectively). The application of the method to the analysis of water samples (tap and mineral water) gave accurate results based on recovery studies (93-106%). Analytical results of real sample analysis were in good agreement with certified values.