Effect of biotite content of hydrogels on enhanced removal of methylene blue from aqueous solution

A series of chitosan-g-poly(acrylic acid)/biotite (CTS-g-PAA/BT) hydrogels with unique clay biotite (BT) were prepared and used to remove cationic dye methylene blue (MB) from aqueous solution by batch adsorption experiments. Variables of the system including BT content, initial pH, contact time, initial concentration, and temperature affecting the adsorption efficiency of MB by CTS-g-PAA/BT hydrogels were investigated. Kinetic studies indicated that the adsorption data well followed pseudo-second-order kinetics. Langmuir and Freundlich isotherm models were applied to experimental equilibrium data of MB adsorption depending on temperature. The adsorption equilibrium data obeyed Langmuir isotherm, and the monolayer adsorption capacity calculated from the Langmuir isotherm was 2,125.70 mg/g for CTS-g-PAA/10% BT at 30 °C. The adsorption capacity was much higher compared with other hydrogels with the same content of other clays. The introduction of BT into the hydrogel could effectively improve its adsorption properties and reduce the cost. Thermodynamic parameters were evaluated for the dye-adsorbent systems and revealed that the adsorption process was spontaneous and exothermic in nature. All the information gave an indication that CTS-g-PAA/10% BT could potentially be applied as an efficient adsorbent for cationic dye removal from aqueous solution.     

Synthesis of magnetic γ-Fe2O3-based nanomaterial for ultrasonic assisted dyes adsorption: Modeling and optimization

γ-Fe₂O₃ nanoparticles were synthesized and loaded on activated carbon. The prepared nanomaterial was characterized by field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectroscopy (EDX), Fourier transforms infrared spectroscopy (FT-IR) and X-ray diffraction (XRD). The γ-Fe₂O₃ nanoparticle-loaded activated carbon (γ-Fe₂O₃-NPs-AC) was used as novel adsorbent for the ultrasonic-assisted removal of methylene blue (MB) and malachite green (MG). Response surface methodology and artificial neural network were applied to model and optimize the adsorption of the MB and MG in their individual and binary solutions followed by the investigation on adsorption isotherm and kinetics. The individual effects of parameters such as pH, mass of adsorbent, ultrasonication time as well as MB and MG concentrations in addition to the effects of their possible interactions on the adsorption process were investigated. The numerical optimization revealed that the optimum adsorption (>99.5% for each dye) is obtained at 0.02 g, 15 mg L⁻¹, 4 min and 7.0 corresponding to the adsorbent mass, each dye concentration, sonication time and pH, respectively. The Freundlich, Langmuir, Temkin and Dubinin–Radushkevich isotherms were studied. The Langmuir was found to be most applicable isotherm which predicted maximum monolayer adsorption capacities of 195.55 and 207.04 mg g⁻¹ for the adsorption of MB and MG, respectively. The pseudo-second order model was found to be applicable for the adsorption kinetics. Blank experiments (without any adsorbent) were run to investigate the possible degradation of the dyes studied in presence of ultrasonication. No dyes degradation was observed.     

Removal of Congo red dye from aqueous solution with nickel-based metal-organic framework/graphene oxide composites prepared by ultrasonic wave-assisted ball milling

Metal-organic frameworks (MOFs) were successfully synthesized by ultrasonic wave-assisted ball milling. In the absence of organic solvent, the coupling effect of ultrasonic wave and mechanical force played an significant role in the synthesis of MOFs. Adsorption of Congo red (CR) was studied in view of adsorption kinetic, isotherm and thermodynamics. The adsorbent was carried out using X-ray diffraction (XRD), thermogravimetric analysis (TGA), N₂ adsorption-desorption isotherms, Raman spectroscopy and scanning electron microscope (SEM) methods. It was found that pseudo-second-order kinetic model and Freundlich adsorption isotherm matched well for the adsorption of CR onto nickel-based metal-organic framework/graphene oxide composites (Ni-MOF/GO). The results of the adsorption thermodynamics indicated that the adsorption process was a spontaneous and endothermic process. The adsorption capacity of graphene oxide/metal-organic frameworks (GO/MOFs) for CR reached 2489 mg/g, much higher than previous reports. It was demonstrated that an increase in the number of active metal sites can dramatically improve the adsorption capacity of dye. A suitable dry temperature is beneficial for the improvement of adsorption capacity for dye. In this paper, the adsorption results indicated that ultrasonic wave-assisted ball milling has a good prospect for synthesis of MOFs with excellent adsorption performance.     

One-step fabricated Fe3O4@C core–shell composites for dye removal: Kinetics,equilibrium and thermodynamics

B-Fe₃O₄@C core–shell composites were synthesized via one-pot hydrothermal carbonization (HTC) process and used as an adsorbent for the removal of methylene blue (MB) from aqueous solution. By using sodium borate as the catalyst, the hydrothermal carbonization process of B-Fe₃O₄@C core–shell composites was optimized and a higher surface area was obtained. The adsorbent was characterized by XRD, Raman spectra, SEM, TEM and N₂ adsorption/desorption isotherms. We studied the dye adsorption process at different conditions and analyzed the data by employing the Langmuir and Freundlich models, and the equilibrium data fitted well with both models. Kinetic analyses were conducted by using the Lagergren pseudo-first-order and pseudo-second-order model and the results showed that the adsorption process was more consistent with the pseudo-second-order kinetics. To better understand the dye adsorption process from the thermodynamics perspective, we also calculated ΔH^ο, ΔS^ο, ΔG^ο and E_a, the results suggesting that the MB adsorption process was physisorption endothermic process, and spontaneous at room temperature. The as-synthesized B-Fe₃O₄@C showing high magnetic sensitivity provides a facile and efficient way to recycle from aqueous solution.     

Improved adsorption performance of nanostructured composite by ultrasonic wave: Optimization through response surface methodology,isotherm and kinetic studies

In this work, ultrasound-assisted adsorption of an anionic dye, sunset yellow (SY) and cationic dyes, malachite green (MG), methylene blue (MB) and their ternary dye solutions onto Cu@ Mn-ZnS-NPs-AC from water aqueous was optimized by response surface methodology (RSM) using the central composite design (CCD). The adsorbent was characterized using Field emission scanning electron microscopy (FESEM), X-ray diffraction (XRD), Energy-dispersive X-ray spectroscopy (EDX) and EDX mapping images. The effects of various parameters such as pH, sonication time, adsorbent mass and initial concentrations of SY, MG and MB were examined. A total 33 experiments were conducted to establish a quadratic model. Cu@ Mn-ZnS-NPs-AC has the maximum adsorption efficiency (>99.5%) when the pH, sonication time, adsorbent mass and initial concentrations of SY, MG and MB were optimally set as 6.0, 5 min, 0.02 g, 9, 12 and 12 mg L⁻¹, respectively. Sonication time has a statistically significant effect on the selected responses. Langmuir isotherm model was found to be best fitted to adsorption and adsorption capacities were 67.5 mg g⁻¹ for SY, 74.6 mg g⁻¹ for MG and 72.9 mg g⁻¹ for MB. Four kinetic models (pseudo-first order, pseudo-second order, Weber–Morris intraparticle diffusion rate and Elovich) were tested to correlate the experimental data and the sorption was fitted well with the pseudo-second order kinetic model.     

Removal of Brilliant Green from wastewater using conventional and ultrasonically prepared poly(acrylic acid) hydrogel loaded with kaolin clay: A comparative study

The present work deals with the removal of Brilliant Green dye from wastewater using a poly(acrylic acid) hydrogel composite (PAA-K hydrogel) prepared by incorporation of kaoline clay. The composite has been synthesized using ultrasound assisted polymerization process as well as the conventional process, with an objective of showing the better effectiveness of ultrasound assisted synthesis. It has been observed that the hydrogel prepared by ultrasound assisted polymerization process showed better results. The optimum conditions for the removal of dye are pH of 7, temperature of 35 °C, initial dye concentration of 30 mg/L and hydrogel loading of 1 g. The extent of removal of dye increased with an increase in the contact time and initial dye concentration. A pseudo-second-order kinetic model has been developed to explain the adsorption kinetics of dye on the PAA-K hydrogel. Thermodynamic and kinetic parameters indicate that the adsorption process is spontaneous in nature and the PAA-K hydrogel prepared by ultrasound process is a promising adsorbent compared to conventional process. The obtained adsorption data has also been fitted into commonly used adsorption isotherms and it has been found that Freundlich as well as Langmuir adsorption isotherm models fits well to the experimental results.     

Optimization of the ultrasonic assisted removal of methylene blue by gold nanoparticles loaded on activated carbon using experimental design methodology

The present study was focused on the removal of methylene blue (MB) from aqueous solution by ultrasound-assisted adsorption onto the gold nanoparticles loaded on activated carbon (Au-NP-AC). This nanomaterial was characterized using different techniques such as SEM, XRD, and BET. The effects of variables such as pH, initial dye concentration, adsorbent dosage (g), temperature and sonication time (min) on MB removal were studied and using central composite design (CCD) and the optimum experimental conditions were found with desirability function (DF) combined response surface methodology (RSM). Fitting the experimental equilibrium data to various isotherm models such as Langmuir, Freundlich, Tempkin and Dubinin–Radushkevich models show the suitability and applicability of the Langmuir model. Analysis of experimental adsorption data to various kinetic models such as pseudo-first and second order, Elovich and intraparticle diffusion models show the applicability of the second-order equation model. The small amount of proposed adsorbent (0.01 g) is applicable for successful removal of MB (RE > 95%) in short time (1.6 min) with high adsorption capacity (104–185 mg g⁻¹).     

Ultrasound assisted synthesis of polyacrylic acid–nanoclay nanocomposite and its application in sonosorption studies of malachite green dye

Synthesis of nanoclay nanocomposite has been undertaken by using polyacryalic acid (PAA) in aqueous medium and ultrasound environment and its application in dye removal has been investigated. The synthesized product was characterized by using FTIR and XRD techniques. The sonosorption capacity of the product namely PAA–nanoclay composite was determined by choosing malachite green (MG) dye as a model pollutant. The effects of various parameters such as nanocomposite loading, pH, various process conditions etc. have been studied. On comparing the results obtained with that of nanoclay as an adsorbent, it was found for an initial concentration of 500 mg/l, the PAA–nanoclay nanocomposite exhibited higher percentage of pollutant removal (68%) and for nanoclay it was 54%. The adsorption data has been correlated using Langmuir and Freundlich models. The fit of the Freundlich isotherm model was found to be good in the entire range of concentration for the experimental sorption data obtained on the nanoclay nanocomposite. A plausible reaction mechanism for use of PAA–nanoclay nanocomposite as an adsorbent is also proposed.     

Probing the role of hydrolytically stable, 3-aminopropyl triethoxysilane crosslinked chitosan/graphene oxide membrane towards Congo red dye adsorption

In this investigation, the practicability of utilizing 3-aminopropyl triethoxysilane (3-APTES) crosslinked chitosan (Ch)/graphene oxide (GO) membranes were explored for adsorptive removal of anionic dyes from aqueous medium. Membranes were successfully fabricated through solution casting technique. Strong interactions amongst matrix (chitosan), 3-APTES, polyvinylpyrrolidone (PVP) and GO were confirmed by Infrared spectroscopy. Thermal stability of the chitosan was improved by adding graphene oxide and results were verified via thermogravimetric (TGA) analysis. Swelling and hydrolytic results confirmed that 2 %-Ch/PVP was a stable membrane while increasing the amount of 3-APTES in the chitosan nanocomposites membrane decreased its stability in aqueous medium. The adsorption characteristics of the membranes were evaluated by the adsorption of Congo red (CR) dye from aqueous medium. The adsorbent can remove 80% of CR from aqueous medium and follows second order kinetics. This study outlines the possibility of exploring green membranes which can be easily fit in various flow systems.     

Studies on the removal of As(III) and As(V) through their adsorption onto granular activated carbon/MnFe2O4 composite: isotherm studies and error analysis

The granular activated carbon/MnFe₂O₄ composite with a mass ratio of 2:1 was synthesized using a simple chemical coprecipitation procedure and used for the removal of As(III) and As(V) from synthetically prepared wastewater. Physicochemical analysis of the composite was carried out through Brunauer, Emmett and Teller surface area and total pore volume, Fourier Transform Infrared Spectroscopy (FT-IR) and Scanning Electron Micrograph and Energy-Dispersive X-Ray Spectroscopy (SEM-EDX). The impact of various adsorption parameters such as the initial pH, adsorbent dose, contact time, temperature and initial arsenic concentration were systematically investigated to evaluate the optimum operating conditions. Nonlinear regression analysis was employed to identify the best-fit isotherm on the basis of three correlation coefficients and three error functions and also to predict the parameters involved in one one-parameter, six two-parameter, nineteen three-parameter, three four-parameter and one five-parameter isotherms. The maximum adsorption capacities estimated using the Langmuir model were 1253 mg/g for As(III) and 1314 mg/g for As(V) at 30 °C temperature and 70 min contact time. The results showed that As(III) and As(V) removal was strongly pH-dependent with an optimum pH value of 7.0 and 4.0, respectively. The mean adsorption energy (E) calculated from the D–R model indicated the nature of adsorption being ion exchange type.     

Preparation, characterization and dye adsorption properties of γ-Fe2O3/SiO2/chitosan composite

A γ-Fe₂O₃/SiO₂/chitosan composite was prepared by water-in-oil emulsification, and characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). Effects of various factors, including adsorbent dosage, initial dye concentration, solution pH, and competing anions, on the adsorption of methyl orange from aqueous solutions by the resulting composite were studied by batch adsorption experiments. The adsorption kinetics was found to follow the pseudo-second-order kinetic model, and intraparticle diffusion was related to the adsorption, but not as a sole rate-controlling step. The equilibrium adsorption data were well described by the Freundlich isotherm model. Evaluation of the thermodynamic parameters ΔG°, ΔH°, and ΔS° revealed that the adsorption process was naturally feasible, spontaneous, and exothermic. The composite was proven to be efficient, suitable and promising for the removal of methyl orange from aqueous solutions since it has a relatively higher adsorption capacity than other low-cost adsorbents.     

Adsorption and photocatalytic degradation of methylene blue using high surface area titanate nanotubes (TNT) synthesized via hydrothermal method

Removal of methylene blue (MB) via adsorption and photocatalysis using titanate nanotubes (TNTs) with different surface areas were investigated and compared to commercial titanium dioxide (TiO₂) P25 Degussa nanoparticles. The TNTs with surface area ranging from 20 m²/g to 200 m²/g were synthesized via hydrothermal method with different reaction times. TEM imaging confirmed the tubular structure of TNT while XRD spectra indicated all TNTs exhibited anatase crystallinity. Batch adsorption rate showed linearity with surface properties of TNTs, where materials with higher surface area showed higher adsorption rate. The highest MB adsorption (70%) was achieved by TNT24 in 60 min whereas commercial TiO₂ exhibited the lowest adsorption of only 10% after 240 min. Adsorption isotherm studies indicated that adsorption using TNT is better fitted into Langmuir adsorption isotherm than Freundlich isotherm model. Furthermore, TNT24 was able to perform up to 90% removal of MB within 120 min, demonstrating performance that is 2-fold better compared to commercial TiO₂. The high surface area and surface Bronsted acidity are the main reasons for the improvement in MB removal performance exhibited by TNT24. The improvement in surface acidity enhanced the adsorption properties of all the nanotubes prepared in this study.     

Adsorption of methylene blue onto sonicated sepiolite from aqueous solutions

The aim of the present study is to enhance the methylene blue (MB) adsorption of sepiolite by ultrasonic treatment. The natural sepiolite was pretreated by sonication to improve the surface characteristics and enhance the dye uptake capacity. Sonication process resulted in a significant increase in the specific surface area (SSA) of sepiolite. The FTIR spectrum of the sonicated sepiolite indicates that the tetrahedral sheet is probably distorted after sonication process. The effect of various parameters such as sonication, pH, initial dye concentration and temperature on dye adsorption has been investigated. The adsorbed amount of MB on sepiolite increased after sonication as well as with increasing pH and temperature. The experimental data were evaluated by applying the pseudo-first- and second-order, and the intraparticle diffusion adsorption kinetic models. Adsorption process of MB onto sepiolite followed the pseudo-second-order rate expression. The experimental data were analyzed by Langmuir and Freundlich isotherms, and found that the isotherm data were reasonably well correlated by Langmuir isotherm. Maximum monolayer adsorption capacity of sepiolite for MB increased from 79.37 to 128.21 mg/g after the sonication. Various thermodynamic parameters, such as ΔG⁰, ΔH⁰ and ΔS⁰ were calculated. The thermodynamics of MB/sepiolite system indicated spontaneous and endothermic nature of the process. Adsorption measurements showed that the process was very fast and physical in nature.     

纸质活性炭纤维的制备及性能表征

通过KOH活化纸巾制备活性炭纤维, 比表面积高达1388 m²/g. 用制得的活性炭纤维作为吸附剂进行亚甲基蓝吸附实验研究,用Langmuir和Freundlich吸附模型分析实验数据,并研究pH值对活性炭纤维吸附亚甲基蓝影响. 活性炭纤维吸附速率更适于Pseudo-second-order动力学模型,相关系数高达0.998. 整个浓度变化区间Langmuir吸附等温线比Freundlich吸附等温线更适合实验数据. 所制备活性炭纤维对亚甲基蓝最大平衡吸附量为520 mg/g,实验发现,pH值越高活性炭纤维对亚甲基蓝吸附量越大.     

Adsorption kinetics,isotherms, and thermodynamic studies for the adsorption of Pb<Superscript>2+</Superscript> and Hg<Superscript>2+</Superscript> metal ions from aqueous medium using Ti(IV) iodovanadate cation exchanger

In the current study, Ti(IV) iodovanadate cation exchanger (TIV) was synthesized and applied for the removal of Pb²⁺ and Hg²⁺ metal ions from the aqueous medium. The adsorption studies were performed by the batch techniques and adsorption parameters viz. contact time, pH, initial metal ion concentration, and temperature were also investigated. The optimum adsorption of Pb²⁺ (95 %) and Hg²⁺ (65 %) were observed at pH 6. The pseudo-second order equation represented the adsorption kinetics with high correlation coefficient. Langmuir model showed the best fitting to the isotherm equilibrium data, with a maximum adsorption capacity of 18.8 mg g^?1 for Pb²⁺ and 17.2 mg g^?1 for Hg²⁺. Furthermore, thermodynamic factors, i.e., ΔG, ΔH, and ΔS, indicated that adsorption of Pb²⁺ and Hg²⁺ onto TIV were spontaneous, endothermic, and feasible in the temperature range of 293–323 K.     

Ultrasound-assisted adsorption of 4-dodecylbenzene sulfonate from aqueous solutions by corn cob activated carbon

This study was aimed at removal of 4-dodecylbenzene sulfonate (DBS) ions from aqueous solutions by ultrasound-assisted adsorption onto the carbonized corn cob (AC). The main attention was focused on modeling the equilibrium and kinetics of adsorption of DBS onto the AC. The AC was prepared from ground dried corn cob by carbonization and activation by carbon dioxide at 880 °C for 2 h in a rotary furnace. The adsorption isotherm data were fitted by the Langmuir model in both the absence and the presence of ultrasound (US). The maximum adsorption capacities of the adsorbent for DBS, calculated from the Langmuir isotherms, were 29.41 mg/g and 27.78 mg/g in the presence of US and its absence, respectively. The adsorption process in the absence and the presence of US obeyed the pseudo second-order kinetics. The intraparticular diffusion model indicated that the adsorption of DBS ions on the AC was diffusion controlled as well as that US promoted intraparticular diffusion. The ΔG° values, ?24.03 kJ/mol, ?25.78 kJ/mol and ?27.78 kJ/mol, were negative at all operating temperatures, verifying that the adsorption of DBS ions was spontaneous and thermodynamically favorable. The positive value of ΔS° = 187 J/mol K indicated the increased randomness at the adsorbent–adsorbate interface during the adsorption of DBS ions by the AC.     

Optimization parameters for adsorption and desorption of Zn(II) and Se(IV) using rice husk ash: kinetics and equilibrium

An attempt at the use of rice husk ash, an agricultural waste, as an adsorbent of Zn(II) and Se(IV) from their aqueous solution is studied. Studies are carried out as a function of contact time, metal ion concentration, adsorbent dose, and pH at 25 °C. Its adsorption capability and adsorption rate are considerably higher and faster for Zn(II) ions than for Se(IV) ions. Zn(II) adsorption was found fast reaching equilibrium within ≃1 h while Se(IV) adsorption was slow reaching equilibrium within ≃100 h. The Bangham equation can be used to express the mechanism for adsorption. The experimental isotherm data were analyzed using Langmiur, Freundlich, and Temkin models. Desorption experiments were carried out using different media with a view to regenerate the spent adsorbent and to recover the adsorbed metal ion.     

Adsorption behavior of a textile dye of Reactive Blue 19 from aqueous solutions onto modified bentonite

The aim of this study is to evaluate adsorption kinetics, isotherms and thermodynamic parameters of Reactive Blue 19 (RB19) onto modified bentonite from aqueous solutions. The effects of pH, contact time, initial dye concentration and temperature were investigated in the experimentally. Natural bentonite was modified by using 1,6-diamino hexane (DAH) as a modifying agent. The characterization of modified bentonite (DAH-bentonite) was accomplished by using FTIR, TGA, BET and elemental analysis techniques. The optimum pH value for the adsorption experiments was found to be 1.5 and all the experiments were carried out at this pH value. The pseudo-second-order kinetic model agrees very well with the experimental results. Equilibrium data were also fitted well to the Langmuir isotherm model in the studied concentration range of RB19 at 20 °C. The results indicate that DAH-modified bentonite is a suitable adsorbent for the adsorption of textile dyes.     

Kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain from aqueous solutions

Spent grain, a main by-product of the brewing industry, is available in large quantities, but its main application has been limited to animal feeding. Nevertheless, in this study, spent grain modified with 1 M NaCl solution as a novel adsorbent has been used for the adsorption of Pb(II) in aqueous solutions. Isotherms, kinetics and thermodynamics of Pb(II) adsorption onto modified spent grain were studied. The equilibrium data were well fitted with Langmuir, Freundlich and Dubinin-Radushkevick (D-R) isotherm models. The kinetics of Pb(II) adsorption followed pseudo-second-order model, using the rate constants of pseudo-second-order model, the activation energy (E_a) of Pb(II) adsorption was determined as 12.33 kJ mol⁻¹ according to the Arrhenius equation. Various thermodynamic parameters such as ΔG^ads, ΔH^ads and ΔS^ads were also calculated. Thermodynamic results indicate that Pb(II) adsorption onto modified spent grain is a spontaneous and endothermic process. Therefore, it can be concluded that modified spent grain as a new effective adsorbent has potential for Pb(II) removal from aqueous solutions.     

Adsorptive removal of congo red dye from aqueous solution using bael shell carbon

This study investigates the potential use of bael shell carbon (BSC) as an adsorbent for the removal of congo red (CR) dye from aqueous solution. The effect of various operational parameters such as contact time, temperature, pH, and dye concentration were studied. The adsorption kinetics was modeled by first-order reversible kinetics, pseudo-first-order kinetics, and pseudo-second-order kinetics. The dye uptake process obeyed the pseudo-second-order kinetic expression at pH 5.7, 7 and 8 whereas the pseudo-first-order kinetic model was fitted well at pH 9. Langmuir, Freundlich and Temkin adsorption models were applied to fit adsorption equilibrium data. The best-fitted data was obtained with the Freundlich model. Thermodynamic study showed that adsorption of CR onto BSC was endothermic in nature and favorable with the positive ΔH° value of 13.613 kJ/mol.