The development of Li<Superscript>+</Superscript> conducting polymer electrolyte based on potato starch/graphene oxide blend

Solid polymer electrolytes based on potato starch (PS) and graphene oxide (GO) have been developed in this study. Blending GO with PS has improved the ionic conductivity and mechanical properties of the electrolytes. In this work, series of polymer blend consisting of PS and GO as co-host polymer were prepared using solution cast method. The most amorphous PS-GO blend was obtained using 80 wt% of PS and 20 wt% of GO as recorded by X-ray diffraction (XRD). Incorporation of 40 wt% lithium trifluoromethanesulfonate (LiCF₃SO₃) into the PS-GO blend increases the conductivity to (1.48 ± 0.35) × 10^?5 S cm^?1. Further enhancement of conductivity was made using 1-butyl-3-methylimidazolium chloride ([Bmim][Cl]). The highest conductivity at room temperature is obtained for the electrolyte containing 30 wt% of [Bmim][Cl] with conductivity value of (4.8?0 ± 0.69) × 10^?4 S cm^?1. Analysis of the Fourier transform infrared spectroscopy (FTIR) spectra confirmed the interaction between LiCF₃SO₃, [Bmim][Cl], and PS-GO blend. The variation of the dielectric constant and modulus studies versus frequency indicates that system of PS-GO-LiCF₃SO₃-[Bmim][Cl] obeys non-Debye behavior.     

Preparation and properties of sulfonated polybenzimidazole-polyimide block copolymers as electrolyte membranes

Sulfonated polybenzimidazole-polyimide block copolymers are synthesized through condensation polymerization at high temperature. The length of the polyimide chain is varied to give a series of block copolymers with various block lengths. The as-synthesized block polymers are used to prepare the corresponding membranes through the solvent evaporation method. The structure of the block copolymers is characterized by Fourier transform infrared spectroscopy (FTIR) and nuclear magnetic resonance spectroscopy (NMR). Their mechanical strength, thermal behavior, water uptake, swelling ratio, and proton conductivity, as well as oxidative stability are also investigated. All the block copolymers exhibit good thermal stability, dimensional stability, mechanical strength, and proton conductivity. Compared to the random sulfonated polyimide-containing benzimidazole membranes with the same degree of sulfonation, the membranes prepared from the block copolymers show higher proton conductivities. The proton conductivities of the block copolymer membranes range from 6.2?×?10^?4 to 1.1?×?10^?2?S cm^?1 at 105 °C. The block copolymer membrane doped with phosphoric acid exhibits proton conductivity higher than 0.2 S cm^?1 at 160 °C, indicating its potential applications in proton exchange membrane fuel cells operated under high temperature and low humidity conditions.     

Preparation and characterization of anhydrous polymer electrolyte membranes based on poly(vinyl alcohol-<Emphasis Type="Italic">co</Emphasis>-ethylene) copolymer

Anhydrous polymer electrolyte membranes with cross-linked structure have been prepared based on poly(vinyl alcohol-co-ethylene) (PVA-co-PE) copolymer. The PVA units of copolymer served to induce thermal cross-linking with 4,5-imidazole dicarboxylic acid (IDA) via esterification while PE units controlled the membrane swelling and the mechanical properties of films. Upon doping with phosphoric acid (PA, H₃PO₄) to form imidazole-PA complexes, the proton conductivity of membranes continuously increased with increasing PA content. As a result, proton conductivity reached 0.01 S/cm at 100 °C under anhydrous conditions. X-ray diffraction analysis revealed that both the d-spacing and crystalline peak of membranes were reduced upon introduction of IDA/PA due to the cross-linking effect. The PVA-co-PE/IDA/PA membranes exhibited good mechanical properties, e.g., 150 MPa of Young’s modulus, as determined by a universal testing machine. Thermal gravimetric analysis also represented that the thermal stability of membranes was increased up to 200 °C upon introduction of IDA/PA.     

Lithium garnet oxide dispersed polymer composite membrane for rechargeable lithium batteries

Free-standing composite polymer membranes comprising of high molecular weight poly (ethylene oxide) (PEO) complexed with lithium perchlorate (LiClO₄) and Li₆La₂BaTa₂O₁₂ (LLBTO) garnet oxide as filler were developed via standard solution-casting method. The as-synthesized composite membranes were investigated through powder x-ray diffraction (PXRD), differential scanning calorimetry (DSC), scanning electron microscopy (SEM), and impedance spectroscopy techniques for their phase, thermal, morphological, and electrical properties, respectively. The lithium ion conductivity of polymer composite membranes consisting of PEO₈/LiClO₄ with various weight percents (5, 10, 15, 20, 25, and 30) of LLBTO were evaluated. We demonstrated a significant enhancement in Li⁺ conductivity with the addition of LLBTO to the polymer-lithium salt complex. Among the investigated membranes, the composite containing 20 LLBTO wt% garnet oxide exhibits maximized room temperature (30 °C) Li⁺ conductivity of 2.03 × 10^?4 S cm^?1 and electrochemical stability greater than 4.5 V.     

Poly (ethylene oxide) (PEO)-based,sodium ion-conducting‚ solid polymer electrolyte films,dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> filler,for applications in sodium ion cells

The studies on solid polymer electrolyte (SPE) films with high ionic conductivity suitable for the realization of all solid-state Na-ion cells? form the focal theme of the work presented in this paper. The SPE films are obtained by the solution casting technique using the blend solution of poly (ethylene oxide) (PEO) with ethylene carbonate (EC) and propylene carbonate (PC) and complexed with sodium nitrate. Structural and thermal studies of SPE films are done by XRD, FTIR spectroscopy, and TGA techniques. Surface morphology of the films is studied using the FESEM. The ionic conductivity of SPE films is determined from the electrochemical impedance spectroscopy studies. For the SPE film with 16 wt% of NaNO₃ used for reacting with the polymer blend of PEO with EC and PC, the ionic conductivity obtained is around 1.08 × 10^?5 S cm^?1. Addition of the Al₂O₃ as the filler material is found to enhance the ionic conductivity of the SPE films. The studies on the Al₂O₃ modified SPE film show an ionic conductivity of 1.86 × 10^–4 S cm^?1, which is one order higher than that of the SPE films without the filler content. For the SPE film dispersed with 8 wt% of Al₂O₃, the total ion transport number observed is around 0.9895, which is quite impressive from the perspective of the applications in electrochemical energy storage devices. From the cyclic voltammetry studies, a wide electrochemical stability window up to 4 V is observed, which further emphasizes the commendable electrochemical behavior of these SPE films.     

A study on the role of BaTiO<Subscript>3</Subscript> in lithum bis(perfluoroethanesulfonyl)imide-based PVDF-HFP nanocomposites

Lithium bis(perfluoroethanesulfonyl)imide (BETI; guest species)-based polyvinylidenefluoride-hexafluoropropylene (PVDF-HFP) (host matrix) polymer nanocomposites (PNC) films by loading barium titanate (BaTiO₃) as a filler in ascending proportions with plasticizer (mixture of EC + DMC) while keeping host and guest content as constants has been investigated by employing AC impedance, thermal, X-ray diffraction (XRD), phase morphology, and Fourier transform infrared (FTIR) studies. The ionic conductivity measurements on these PNC show that 2.5% BaTiO₃-loaded polymer nanocomposites (PNC) showed mitigation in magnitude of the conductivity compared with that of 0 wt.% loaded PNC; but increase in conductivity is noted thereafter with increase in filler content of up to 7.5 wt.%. The higher conductivity is observed for 7.5% filler-loaded membrane. The XRD study identifies suppression of polymer phase associated with (200) plane. The SEM image illustrates inhomogeneity in surface morphologies for PNCs with the filler dispersed. The thermal profile registers the endothermic changes associated with polymer host indicating a varying heat of fusion ∆Hm with filler increase. FTIR studies confirm possible interaction between various constituents of the PNCs.     

Influences of interfacial adhesion on gas barrier property of functionalized graphene oxide/ultra-high-molecular-weight polyethylene composites with segregated structure

The segregated graphene oxide(GO)/ultra-high-molecular-weight polyethylene (UHMWPE) composite films with various interfacial adhesion property were prepared by mechanical blending method from UHMWPE, GO, dodecyl amine (DA) functionalized graphene oxide(DA–GO) or uniform DA–GO/high density polyethylene (DA–GO/HDPE) powder. The results of XRD and XPS indicated that DA chain was successfully grafted onto GO sheets via a chemical method, which enhanced the interfacial adhesion between UHMWPE particles and GO sheets. The characterizations of POM and SEM proved that good segregated structure was only obtained in DA–GO/UHMWPE or DA–GO/HDPE/UHMWPE composite. Strong interfacial adhesion between fillers and matrix exhibits positive effect on gas barrier property. Compared to the GO/UHMWPE composite film, dramatic decrease in O₂ permeability coefficient by 42.2 and 48.1%, from 15.4 × 10^?14 to 8.9 × 10^?14 and 8.0 × 10^?14 cm³ cm cm^?2 s^?1 Pa^?1, is achieved upon the addition of only 0.5 wt% fillers, respectively. The DSC results demonstrated that the enhanced gas barrier performance was ascribed to the strong interfacial adhesion between DA–GO/HDPE and UHWMPE matrix, rather than the crystallinity of UHWMPE matrix. Additionally, the decrease in UHMWPE particle size might be conducive to improving the gas barrier property of composite films due to the formation of more isolation layers perpendicular to the film plane.     

Polyethylene-supported poly(methyl methacrylate<Emphasis Type="Italic">-co-</Emphasis>butyl acrylate)-based novel gel polymer electrolyte for lithium ion battery

A new copolymer, poly(methyl methacrylate-co-butyl acrylate) (P(MMA-co-BA)), was synthesized by emulsion polymerization with different mass ratio of methyl methacrylate (MMA) and butyl acrylate (BA). The membranes were prepared by phase inversion and corresponding gel polymer electrolytes (GPEs) were obtained by immersing the membrane into a liquid electrolyte. In this design, the hard monomer MMA provided the copolymer with good electrolyte uptake, while the soft monomer BA provided the GPE with strong adhesion between the anode and cathode of lithium ion battery. The properties of the resulting product were investigated by Fourier transform infrared spectroscopy, nuclear magnetic resonance spectra, scanning electron spectroscopy, linear sweep voltammetry, thermogravimetric analysis, cyclic voltammetry, electrochemical impedance spectroscopy and charge/discharge test. The results show that the obtained GPE based on P(MMA-co-BA) with the mass ratios of MMA and BA = 6:1 exhibits good conductivity (as high as 1.2 × 10^?3 S cm^?1) at room temperature and high electrochemical stability (up to 4.9 V vs. Li/Li⁺). With the application of the polyethylene (PE)-supported GPE in Li/Li(Li_0.13Ni_0.30Mn_0.57)O₂ battery, the battery presents good cyclic stability (maintaining 95.4 % of its initial discharge capacity after 50 cycles) at room temperature.     

Electrochemical performance of CeO<Subscript>2</Subscript> nanoparticle-decorated graphene oxide as an electrode material for supercapacitor

Cerium oxide nanoparticles and cerium oxide nanoparticle-decorated graphene oxide (GO) are synthesized via a facile chemical coprecipitation method in the presence of hexadecyltrimethylammonium bromide (CTAB). Nanostructure studies and electrochemical performances of the as-prepared samples were systematically investigated. The crystalline structure and morphology of the nanocomposites were examined by X-ray diffraction (XRD), scanning electron microscopy (SEM), transition electron microscopy (TEM), Raman spectrum, and X-ray photoelectron spectroscopy (XPS). Electrochemical properties of the CeO₂ electrode, the GO electrode, and the nanocomposites electrodes were investigated by cyclic voltammetry (CV), galvanostatic charge/discharge (GCD), and electrochemical impedance spectroscopy (EIS) measurements. The CeO₂ nanoparticle-decorated GO (at the mole ratio of CeO₂/GO = 1:4) electrode exhibited excellent supercapacitive behavior with a high specific capacitance of 382.94 F/g at the current density of 3.0 A/g. These superior electrochemical features demonstrate that the CeO₂ nanoparticle-decorated GO is a promising material for next-generation supercapacitor systems.     

Properties of hydrophobically-modified graphene oxide (HG)/butyl rubber (IIR) nanocomposites prepared by shear mixing process

Abstract

Butyl rubber (IIR)/hydrophobically modified graphene oxide (GO) (HG) nanocomposites were prepared via shear-induced compounding. Hydrophilic GO was synthesized through the chemical oxidation of graphite (GP) and modified hydrophobically by octadecylamine which has a hydrophobic long alkyl chain. The obtained HG was characterized by Fourier transform infrared and wide-angle X-ray diffraction (WAXD) patterns. It was well dispersed in toluene for more than 30 days under stationary condition. The IIR/HG nanocomposites were prepared by the shear mixing process and followed by thermal vulcanization process through compression molding. Their properties were studied using oscillating disk rheometer, universal testing machine, differential scanning calorimetry, thermogravimetric analysis, WAXD patterns, and scanning electron microscope analysis. The hydrophobic HG was dispersed at the nanoscale within IIR matrix, and the resulting nanocomposites had significantly reduced curing time. The overall tensile properties were enhanced.     

Preparation of TEMPO-contained pyrrole copolymer by in situ electrochemical polymerization and its electrochemical performances as cathode of lithium ion batteries

Composite electrodes based on the nitroxide free radical-contained pyrrole copolymer (PPy-co-PPy-C-TEMPO) as active material were one-step synthesized by in situ electrochemical polymerization, which was then directly applied as the cathode of lithium ion batteries. The structure, morphology, electrochemical property, and charge-discharge performances of prepared copolymers were characterized by FTIR, SEM, cyclic voltammogram, electrochemical impedance spectroscopy, and galvanostatic charge-discharge testing, respectively. The results demonstrated that PPy-co-PPy-C-TEMPO-based composite cathodes have been successfully prepared by in situ electrochemical method, and the introduction of the nitroxide free radical (TEMPO) could obviously affect the morphology and electrochemical characteristics of the obtained electroactive polymers. And the charge/discharge tests showed that with the introduction of the TEMPO, PPy-co-PPy-C-TEMPO-based composite cathodes exhibited an improved specific capacity of 70.9 mAh g^?1 for PPy-co-PPy-C-TEMPO (4:1) and 62.6 mAh g^?1 for PPy-co-PPy-C-TEMPO (8:1) as measured at 20 mA g^?1 between 2.5 and 4.2 V, which were remarkably higher than that of the pure PPy cathode of 41.0 mAh g^?1 under the same experimental conditions. Also, the obtained PPy-co-PPy-C-TEMPO copolymers demonstrated an acceptable cycling stability during the charge-discharge process. These obtained cell performances for the composite cathodes were attributed to the application of the in situ electrochemical polymerization technology, which enhanced the intimate integration between conductive polymer film and electrode. Furthermore, the introduction of TEMPO-contained pyrrole (Py-C-TEMPO) improved the morphology of the composite cathode, which was in favor of the utilization of active materials and the improved electrochemical performances.     

Synthesis and Characterization of Poly(vinyl pyrrolidone)/Reduced Graphene Oxide Nanocomposite

Poly(vinyl pyrrolidone) (PVP)/reduced graphene oxide (RGO) nanocomposites were synthesized by reducing graphene oxide in the polymer matrix at different temperatures. The effects of the GO content on the properties of the nanocomposites were investigated by Fourier-transform infrared (FTIR) spectroscopy and thermogravimetric analysis (TGA). The degree of dispersion of GO in the PVP matrix was examined by field-emission scanning electron microscopy. The results showed that both GO and RGO were well dispersed in the PVP matrix. Under low filler content, the improvement of onset decomposition temperatures of PVP nanocomposites was not obviously observed, but the amounts of residual char of the PVP nanocomposites were clearly increased. In addition, the decomposition temperature peak values of the PVP nanocomposites were increased, while the peak was broadened.     

Excellent electromagnetic interference shielding effectiveness of chemically reduced graphitic oxide paper at 101 GHz*

Graphitic oxide (GO) was synthesized by oxidation of graphite powder using Hummer’s method and the formed GO is solution processed into paper-like macroscopic form. Subsequently, chemically reduced graphitic oxide paper (CRGOP) is prepared by hydrazine vapours induced reduction of formed GO precursor based paper. The formation of GO and its successful reduction to RGO phase is confirmed by FTIR, Raman Spectroscopy and X-ray diffraction. It has been observed that due to high electrical conductivity ~200 micron thick CRGOP display excellent EMI shielding performance at very high frequency of 101 GHz frequency with total shielding effectiveness (SE) value of ?35.49 dB (i.e. >99.97% blocking of incident EM radiation) which is much higher compared to pristine GO paper (?1.55 dB) or comparable to expanded graphite (EG) sheet (?35.61 dB). Due to their lightweight nature, these freestanding CRGOPs display average specific SE value of ?221.8 dB cm³/g. Besides, their excellent flexibility and makes them potential candidate for lightweight EMI gasketing material compared to other forms of flexible carbons like EG.     

Electrical characterization of PVA-based nanocomposite electrolyte nanofibre mats doped with a multiwalled carbon nanotube

An attempt has been made to prepare and characterise ammonium thiocyanate (NH₄SCN) salt and a multiwall carbon nanotube (MWNT)-doped polyvinyl alcohol-based nanofibre mats using an electrospinning process. The X-ray diffraction result shows an improvement in the amorphous nature of composite electrolyte fibre mats with increasing concentrations of the MWNT filler. The DSC behaviour of these nanofibre mat exhibits better thermal response upon dispersal of the filler. Composite electrolyte nanofibre mat doped with 6 wt% MWNT shows optimum conductivity, viz., 5.8?×?10^?4 Scm^?1. The temperature dependence of the bulk electrical conductivity displays a combination of Arrhenius and Vogel–Tammam–Fulcher nature. Dielectric loss studies have also been used to understand the conduction process in the system. Jonscher power law seems to be obeyed during ac conductivity measurements of the fibre mats.     

Effect of liquid crystal ionomer intercalated montmorillonite nanocomposites on PEO/PLA solid polymer electrolytes

A series of solid polymer electrolytes (SPEs) based on poly (ethylene oxide)/polylactic acid (PEO/PLA) with liquid crystal ionomer (LCI) intercalated montmorillonite (MMT) nanocomposites (LCI-MMT) has been prepared by solution blending method. The effects of LCI-MMT on the structural, crystallization, thermal, and ionic conductivity properties of solid polymer electrolytes have been analyzed. It is demonstrated that the incorporation of LCI-MMT into the blend suppressed the crystallinity of PEO and increased the crystallinity of PLA. The maximum ionic conductivity is found to be in the range of 1.05?×?10^?5 S/cm for 0.5 wt% LCI-MMT, which is higher than that of the LCI-MMT-free polymer electrolyte (5.36?×?10^?6 S/cm) at room temperature.     

Preparation and Rheological Characteristics of Ethylene‐Vinyl Acetate Copolymer/Organoclay Nanocomposites

Ethylene‐vinyl acetate copolymer (EVA) with 40 wt.% vinyl acetate content (EVA40)/organoclay nanocomposites were prepared using a melt intercalation method with several different clay concentrations (2.5, 5.0, 7.5, and 10.0 wt.%). X‐ray diffraction confirmed the formation of exfoliated nanocomposite in all cases with disappearance of the characteristic peak corresponding to the d‐spacing of the pristine organoclay. Transmission electron microscopy studies also showed an exfoliated morphology of the nanocomposites. Morphology and thermal properties of the nanocomposites were further examined by means of scanning electron microscopy (SEM) and thermo gravimetric analysis (TGA), respectively. Rheological properties of the EVA40/organoclay nanocomposites were investigated using a rotational rheometer with parallel‐plate geometry in both steady shear and dynamic modes, demonstrating remarkable differences with the clay contents in comparison to that of pure EVA40 copolymer.     

Ultrasonic-microwave assisted synthesis of three-dimensional polyvinyl alcohol carbonate/graphene oxide sponge and studies of surface resistivity and thermal stability

In the article, graphene oxide (GO) was prepared by flake graphite, nitric acid and peroxyacetic acid via the sonochemical method and characterized, and polyvinyl alcohol carbonate/GO composite (PVAC/GO composite) was synthesized by polyvinyl alcohol (PVA), dimethyl carbonate (DMC) and GO via the approach of transesterification in the case of ultrasonic-microwave synergistic effects and characterized, and three-dimensional PVAC/GO sponge (3D PVAC/GO sponge) was manufactured by PVAC/GO composite via the foaming approach and characterized, and the thermal stability and surface resistivity of 3D PVAC/GO sponge were investigated. Based on those, it had been attested that PVAC polymer was structured by DMC and PVA and had the six-membered lactone rings and the ether bonds, and PVAC/GO composite was constituted by 2D GO lattice and PVAC polymer, and 3D PVAC/GO sponge was constructed by PVAC/GO composite, and the surface resistivity of 3D PVAC/GO sponge with 0.00, 0.60, 1.20, 1.80 and 2.40 g of GO were 9.07 × 10⁷, 6.02 × 10⁷, 4.65 × 10⁷, 2.47 × 10⁷ and 1.06 × 107 O/sq, and the thermal stability of 3D PVAC/GO sponge had improved.     

Effect on ion dissociation in MWCNT-based polymer nanocomposite

Polymer nanocomposite has been proven to improve the property of polymer salt complex. Organo-modified clay and inorganic oxides are the most commonly used filler for polymer nanocomposite (PNC). However, single wall carbon nanotube (SWCNT)/multiwall carbon nanotube (MWCNT) are becoming popular filler for PNC for their high surface area and high mechanical stability. In this work, a series of PNC sample has been prepared by using polyethylene oxide (PEO)-polydimethylsiloxane (PDMS) blend as polymer matrix, an optimized salt stoichiometry of Ö/Li ~15, and surface-modified MWCNT as filler. The effect of ion-polymer and ion-MWCNT interaction in the polymer nanocomposite has been investigated by using XRD, SEM, FTIR, and electrical study. X-ray diffraction pattern confirms the dispersion of MWCNT inside the polymer chain and modifies the structural parameter of the polymer matrix. FTIR spectra indicate inclusion of MWCNT inside the polymer salt complex which changes the ion dissociation/association in the polymer host matrix. Further, the changes in structural, thermal, and electrical property of the polymer salt complex system have been studied by using SEM, DSC, and impedance analysis. Dc conductivity study shows that optimized PNC sample has conductivity of 8.04 × 10⁻⁵ S cm⁻¹. This is almost two order enhancement from pure polymer salt system (10⁻⁶ S cm⁻¹).

     

A Study on Compatibility and Properties of POE/PS/SEBS Ternary Blends

Ethylene‐α‐olefin copolymer (POE)/polystyrene (PS)/poly(styrene‐b‐ethylene‐co‐butylene‐b‐styrene) (SEBS) blends were prepared via melt blending in a co‐rotating twin‐screw extruder. The effects of SEBS copolymer on the morphology and rheological and mechanical properties of the blends were studied. Scanning electron microscopy (SEM) photos showed that the addition of SEBS copolymer resulted in finer dispersion of PS particles in the POE matrix and better interfacial adhesion between POE and PS compared with POE/PS blends, which exhibited a very coarse morphology due to the immiscibility between them. Interestingly, the tensile strength increased from 12.5 MPa for neat POE to 23.5 MPa for the POE/PS/SEBS (60/10/30) blend, whereas the tensile strengths of POE/PS (85.7/14.3) blend and POE/SEBS (66.7/33.3) blend were only 10.5 and 16.5 MPa, respectively. This indicates that both SEBS copolymer and PS have a synergistic reinforcing effect on POE. Dynamic mechanical thermal analysis (DMTA) and dynamic rheological property measurement also revealed that there existed some interactions between POE and SEBS as well as between SEBS and PS. DMTA results also showed that the storage modulus of POE increased when PS and SEBS were incorporated, especially at high temperature, which means that the service temperature of POE was improved.     

Synthesis and characterization of graphene oxide,reduced graphene oxide and their nanocomposites with polyethylene oxide

This work describes the synthesis of GO, rGO and their nanocomposites with PEO. GO and rGO were prepared by the modified Hummers method and in-situ reduction of GO utilizing green reductant L (+) Ascorbic acid. The nanocomposites were characterized by Fourier-transform infrared spectroscopy (FT-IR), X-ray powder diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Thermogravimetric Analysis (TGA), and Universal Testing Machine (UTM). FT-IR and XRD confirmed the synthesis of GO and rGO. FE-SEM confirmed the uniformly exfoliated GO and rGO nanosheets in the polymer matrix. Hydrogen bonding was the main interaction mechanism for GO with PEO while no interaction was detected by FT-IR for rGO. Enhanced thermal stability was observed for both GO/PEO and rGO/PEO nanocomposites. The mechanical analysis showed an increase in Young's modulus, tensile strength, and elongation at break for GO/PEO nanocomposites, which is attributed to the homogeneous dispersion and hydrophilic hydrogen bonding interaction of GO with PEO.