Generation of MoS<Subscript>2</Subscript> quantum dots by laser ablation of MoS<Subscript>2</Subscript> particles in suspension and their photocatalytic activity for H<Subscript>2</Subscript> generation

MoS₂ quantum dots (QDs) have been obtained in colloidal suspensions by 532 nm laser ablation (7 ns fwhp/pulse, 50 mJ/pulse) of commercial MoS₂ particles in acetonitrile. High-resolution transmission electron microscopy images show a lateral size distribution from 5 to 20 nm, but a more homogeneous particle size of 20 nm can be obtained by silica gel chromatography purification in acetonitrile. MoS₂ QDs obtained by laser ablation are constituted by 3–6 MoS₂ layers (1.8–4 nm thickness) and exhibit photoluminescence whose λ_PL varies from 430 to 530 nm depending on the excitation wavelength. As predicted by theory, the confinement effect and the larger periphery in MoS₂ QDs increasing the bandgap and having catalytically active edges are reflected in an enhancement of the photocatalytic activity for H₂ generation upon UV–Vis irradiation using CH₃OH as sacrificial electron donor due to the increase in the reduction potential of conduction band electrons and the electron transfer kinetics.     

Photodeposition of ultrathin MoS<Subscript>2</Subscript> nanosheets onto cubic CdS for efficient photocatalytic H<Subscript>2</Subscript> evolution

In this work, the photocatalyst composed of ultrathin MoS₂ nanosheets onto the surface of cubic CdS nanoparticles with an average diameter of 7~10 nm has been successfully fabricated through a facile and mild photodeposition route. The ultrathin MoS₂ nanosheets as a cocatalyst were demonstrated to greatly boost photocatalytic H₂ evolution over cubic CdS upon visible light irradiation. It was clearly revealed that both the cubic CdS substrate and structure of ultrathin MoS₂ nanosheets play critical roles in the observed efficient H₂ evolution. The cubic CdS offers a strong adherence for ultrathin MoS₂ nanosheets to form a well contact interface, across which the photogenerated charge transfer and charge separation are achieved. The ultrathin MoS₂ nanosheets introduce a high density of unsaturated active S atoms for H₂ evolution.     

Flower-like MoS<Subscript>2</Subscript> supported on three-dimensional graphene aerogels as high-performance anode materials for sodium-ion batteries

Flower-like MoS₂ supported on three-dimensional graphene aerogel (MoS₂/GA) composite has been prepared by a facile hydrothermal method followed by subsequent heat-treatment process. Each of MoS₂ microflowers is surrounded by the three-dimensional graphene nanosheets. The MoS₂/GA composite is applied as an anode material of sodium-ion batteries (SIBs) and it exhibits high initial discharge/charge capacities of 562.7 and 460 mAh g^?1 at a current density of 0.1 A g^?1 and good cycling performance (348.6 mAh g^?1 after 30 cycles at 0.1 A g^?1). The good Na⁺ storage properties of the MoS₂/GA composite could be attributed to the unique structure which flower-like MoS₂ are homogeneously and tightly decorated on the surface of three-dimensional graphene aerogel. Our results demonstrate that as-prepared MoS₂/GA composite has a great potential prospect as anodes for SIBs.     

Facile growth of monolayer MoS<Subscript>2</Subscript> film areas on SiO<Subscript>2</Subscript>

Areas of single-layer MoS₂ film can be prepared in a tube furnace without the need for temperature control. The films were characterized by means of Raman spectroscopy, photoluminescence, low-energy electron diffraction and microscopy, and X-ray photoelectron spectroscopy and mapping. Transport measurements show n-doped material with a mobility of 0.26 cm² V^-1 s^-1.     

High-efficiency preparation of oil-dispersible MoS<Subscript>2</Subscript> nanosheets with superior anti-wear property in ultralow concentration

Molybdenum disulfide (MoS₂) nanosheets are a promising lubricant additive for enhanced engine efficiency in cars. However, high-cost production methods and poor dispersion have limited their application in industry. In this study, the ball milling process is demonstrated as a low-cost and high-efficient method for fabrication of oil-dispersible MoS₂ nanosheet, and the ball milling parameters are optimized. Moreover, the lubrication effectiveness of ball-milled MoS₂ nanosheet was also evaluated. Results indicated that well-dispersed MoS₂ nanosheets with a size of 250 nm can be manufactured with optimized surfactants of zinc dialkyldithiphosphates (ZDDP) and polyisobutylene succinimide (PIBS) after being ball milled for 36 h. Tribological results revealed that a friction coefficient of white oil with 0.25% MoS₂ nanosheets reached 0.075, much lower than that of lubricant without nanosheets (0.16). The wear scar radius of 0.015% MoS₂ nanosheets was similar with that of Hertz contact, and the wear scar radius reduction reached 20% compared with that of 1% ZDDP. In addition, EDS and XPS results indicated the formation of a MoS₂ and FeS tribofilm on the wear surface.     

CeO<Subscript>2</Subscript> coating to improve the performance of Li[Li<Subscript>0.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>]O<Subscript>2</Subscript>

The Li[Li_0.2Mn_0.54Ni_0.13Co_0.13]O₂ coated with CeO₂ has been fabricated by an ionic interfusion method. Both the bare and the CeO₂-coated samples have a typical layered structure with R-3m and C2/m space group. The results of XRD and TEM images display that the CeO₂ coating layer on the precursor could enhance the growth of electrochemically active surface planes ((010), (110), and (100) planes) in the following ionic interfusion process. The results of galvanostatic cycling tests demonstrate that the CeO₂-coated sample has a discharge capacity of 261.81 mAh g^?1 with an increased initial Coulombic efficiency from 62.4 to 69.1% at 0.05 °C compared with that of bare sample and delivers an improved capacity retention from 71.7 to 83.4% after 100 cycles at 1 °C (1 °C?=?250 mA g^?1). The results of electrochemical performances confirm that the surface modification sample exhibits less capacity fading, lower voltage decay, and less polarization.     

Roles of Al-doped ZnO (AZO) modification layer on improving electrochemical performance of LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> thin film cathode

Al-doped ZnO (AZO) was sputtered on the surface of LiNi_1/3Co_1/3Mn_1/3O₂ (NCM) thin film electrode via radio frequency magnetron sputtering, which was demonstrated to be a useful approach to enhance electrochemical performance of thin film electrode. The structure and morphology of the prepared electrodes were characterized by X-ray diffraction, scanning electron microscopy, energy dispersive spectrometer, and transmission electron microscopy techniques. The results clearly demonstrated that NCM thin film showed a strong (104) preferred orientation and AZO was uniformly covered on the surface of NCM electrode. After 200 cycles at 50 μA μm^?1 cm^?2, the NCM/AZO-60s electrode delivered highest discharge capacity (78.1 μAh μm^?1 cm^?2) compared with that of the NCM/AZO-120s electrode (62.4 μAh μm^?1 cm^?2) and the bare NCM electrode (22.3 μAh μm^?1 cm^?2). In addition, the rate capability of the NCM/AZO-60s electrode was superior to the NCM/AZO-120s and bare NCM electrodes. The improved electrochemical performance can be ascribed to the appropriate thickness of the AZO coating layer, which not only acted as HF scavenger to keep a stable electrode/electrolyte interface but also reduced the charge transfer resistance during cycling.     

Synthesis and electrochemical properties of Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> cathode material for lithium-ion battery

The layered Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ lithium-rich manganese-based solid solution cathode material has been synthesized by a simple solid-state method. The as-prepared material has a typical layered structure with R-3m and C2/m space group. The synthesized Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has an irregular shape with the size range from 200 to 500 nm, and the primary particle of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ has regular sphere morphology with a diameter of 320 nm. Electrochemical performances also have been investigated. The results show that the cathode material Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ prepared at 900 °C for 12 h has a good electrochemical performance, which can deliver a high initial discharge capacity of 233.5, 214.2, 199.3, and 168.1 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. After 50 cycles, the capacity retains 178.0, 166.3, 162.1, and 155.9 mAh g^?1 at 0.1, 0.2, 0.5, and 1 C, respectively. The results indicate that the simple method has a great potential in synthesizing manganese-based cathode materials for Li-ion batteries.     

A lithium salt additive Li<Subscript>2</Subscript>ZrF<Subscript>6</Subscript> for enhancing the electrochemical performance of high-voltage LiNi<Subscript>0.5</Subscript>Mn<Subscript>1.5</Subscript>O<Subscript>4</Subscript> cathode

In this work, Li₂ZrF₆, a lithium salt additive, is reported to improve the interface stability of LiNi_0.5Mn_1.5O₄ (LNMO)/electrolyte interface under high voltage (4.9 V vs Li/Li⁺). Li₂ZrF₆ is an effective additive to serve as an in situ surface coating material for high-voltage LNMO half cells. A protective SEI layer is formed on the electrode surface due to the involvement of Li₂ZrF₆ during the formation of SEI layer. Charge/discharge tests show that 0.15 mol L^?1 Li₂ZrF₆ is the optimal concentration for the LiNi_0.5Mn_1.5O₄ electrode and it can improve the cycling performance and rate property of LNMO/Li half cells. The results obtained by electrochemical impedance spectroscopy (EIS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and X-ray photoelectron spectroscopy (XPS) demonstrate that Li₂ZrF₆ can facilitate the formation of a thin, uniform, and stable solid electrolyte interface (SEI) layer. This layer inhibits the oxidation decomposition of the electrolyte and suppresses the dissolution of the cathode materials, resulting in improved electrochemical performances.     

Thermoeletrochemical study on LiNi<Subscript>0.8</Subscript>Co<Subscript>0.1</Subscript>Mn<Subscript>0.1</Subscript>O<Subscript>2</Subscript> with in situ modification of Li<Subscript>2</Subscript>ZrO<Subscript>3</Subscript>

To improve the electrochemical performance of Nickel-rich cathode material LiNi_0.8Co_0.1Mn_0.1O₂, an in situ coating technique with Li₂ZrO₃ is successfully applied through wet chemical method, and the thermoelectrochemical properties of the coated material at different ambient temperatures and charge-discharge rates are investigated by electrochemical-calorimetric method. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) tests demonstrate that the Li₂ZrO₃ coating decreases the electrode polarizatoin and reduces the charge transfer resistance of the material during cycling. Moreover, it is found that with the ambient temperatures and charge-discharge rates increase, the specific capacity decreases, the amount of heat increases, and the enthalpy change (ΔH) increases. The specific capacity of the cells at 30 °C are 203.8, 197.4, 184.0, and 174.5 mAh g^?1 at 0.2, 0.5, 1.0, and 2.0 C, respectively. Under the same rate (2.0 C), the amounts of heat of the cells are 381.64, 645.32, and 710.34 mJ at 30, 40, and 50 °C. These results indicate that Li₂ZrO₃ coating plays an important role to enhance the electrochemical performance of LiNi_0.8Co_0.1Mn_0.1O₂ and reveal that choosing suitable temperature and current is critical for solving battery safety problem.     

Improved electrochemical properties of YF<Subscript>3</Subscript>-coated Li<Subscript>1.2</Subscript>Mn<Subscript>0.54</Subscript>Ni<Subscript>0.13</Subscript>Co<Subscript>0.13</Subscript>O<Subscript>2</Subscript> as cathode for Li-ion batteries

Yttrium fluoride YF₃ layer with different coating contents is successfully covered on the surface of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂ via a common wet chemical approach. The XRD, SEM, TEM, and charge-discharge tests are applied to investigate the influence of YF₃ layer on the micro-structural, morphology, and electrochemical properties of Li_1.2Mn_0.54Ni_0.13Co_0.13O₂. And the electrochemical test results demonstrate that the YF₃-coated LMNCO samples exhibit the improved electrochemical properties. The 2wt.%YF₃-coated LMNCO delivers a discharge capacity of 116.6 mAh g^?1 at 5 C rate, much larger than that (95.6 mAh g^?1) of the pristine one. Besides, the electrochemical impedance spectroscopy (EIS) and cyclic voltammetric results indicate that the YF₃ coating layer can promote the optimization formation of SEI film and reversibility of the electrochemical redox.     

Synthesis and electrochemical properties of P2-Na<Subscript>2/3</Subscript>Ni<Subscript>1/3</Subscript>Mn<Subscript>2/3</Subscript>O<Subscript>2</Subscript>

The pure phase P2-Na_2/3Ni_1/3Mn_2/3O₂ was synthesized by a solid reaction process. The optimum calcination temperature was 850 °C. The as-prepared product delivered a capacity of 158 mAh g^?1 in the voltage range of 2–4.5 V, and there was a phase transition from P2 to O2 at about 4.2 V in the charge process. The P2 phase exhibited excellent intercalation behavior of Na ions. The reversible capacity is about 88.5 mAh g^?1 at 0.1 C in the voltage range of 2–4 V at room temperature. At an elevated temperature of 55 °C, it could remain as an excellent capacity retention at low current rates. The P2-Na_2/3Ni_1/3Mn_2/3O₂ is a potential cathode material for sodium-ion batteries.     

Enhanced lithium-ion storage and hydrogen evolution reaction catalysis of MoS<Subscript>2</Subscript>/graphene nanoribbons hybrids with loose interlaced three-dimension structure

Molybdenum disulfide hybridized with graphene nanoribbon (MoS₂/GNR) was prepared by mild method. MoS₂/GNR hybrids interlace loosely into a three-dimension structure. GNR hybridization can improve the dispersity of MoS₂, reduce the grain size of MoS₂ to 3–6 nm, increase the specific surface area, and broaden the interlamellar spacing of MoS₂ (002) plane to 0.67–0.73 nm, which facilitates the transportation of Li⁺ ions for lithium-ion battery. MoS₂/GNR hybrids have better cyclic durability, higher specific discharge capacity, and superior rate performance than MoS₂. The electrocatalytic activity in hydrogen evolution reaction shows that MoS₂/GNR hybrids have the lower overpotential and the larger current density with a negligible current loss after 2000 cycles. Hybridizing with GNRs enhances both the lithium-ion electrochemical storage and the electrocatalytic activity of MoS₂.

Open image in new window

Graphical abstract MoS₂/GNR hybrid prepared by a mild method is interlaced loosely into a three-dimension structure. Superior electrochemical performances of MoS₂/GNR hybrids than MoS₂ have been highlighted for the potential application for long- term durability energy-storage devices and HER electrocatalytic materials.

     

Templated synthesis of plate-like MoS<Subscript>2</Subscript> nanosheets assisted with HNTs and their tribological performance in oil

Two-dimensional MoS₂ nanosheets were synthesized by using halloysite nanotubes (HNTs) as template under the hydrothermal synthesis. The structure and morphology of the as-synthesized MoS₂ nanosheets were determined by a series of characterizations. The results showed that the as-synthesized MoS₂ nanosheets were of the plate-like structure with about five layers, and the basal spacing was about 0.63 nm. It was demonstrated that HNTs played a crucial template role in the formation of the plate-like MoS₂ nanosheets. The formation mechanism was proposed. Furthermore, the tribological performance of the as-prepared MoS₂ nanosheets in oil was intensively examined on the ball-on-ball wear tester. The testing results verified that the as-prepared MoS₂ nanosheets as additive could significantly improve the friction performance of oil, which exhibited the good antifriction, antiwear, and load-carrying properties.     

Thermal sensors based on Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> and (Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>70</Subscript>(Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>30</Subscript> thin films

Thin films of Sb₂Te₃ and (Sb₂Te₃)₇₀(Bi₂Te₃)₃₀ alloy and have been deposited on precleaned glass substrate by thermal evaporation technique in a vacuum of 2?×?10^?6 Torr. The structural study was carried out by X-ray diffractometer, which shows that the films are polycrystalline in nature. The grain size, microstrain and dislocation density were determined. The Seebeck coefficient was determined as the ratio of the potential difference across the films to the temperature difference. The power factor for the (Sb₂Te₃)₇₀ (Bi₂Te₃)₃₀ and (Sb₂Te₃) is found to be 19.602 and 1.066 of the film of thickness 1,500 Å, respectively. The Van der-Pauw technique was used to measure the Hall coefficient at room temperature. The carrier concentration was calculated and the results were discussed.     

High-temperature complex impedance and modulus spectroscopic studies of doped Na<Subscript>0.5</Subscript>Bi<Subscript>0.5</Subscript>TiO<Subscript>3</Subscript>-BaTiO<Subscript>3</Subscript> ferroelectric ceramics

Lead-free Na_0.5Bi_0.5TiO₃ (NBT) and (1 ? x)Na_0.5Bi_0.5TiO₃ + xBaTiO₃ with x = 0.1 and 0.2 (where x = 0.1 and 0.2 are named as NBT1 and NBT2, respectively), (1 ? y)Na_0.5Bi_0.5TiO₃ + yBa_0.925Nd_0.05TiO₃ with y = 0.1 and 0.2 (where y = 0.1 and 0.2 are named as NBT3 and NBT4, respectively)-based relaxor ferroelectric ceramics were prepared using the sol-gel method. The crystal structure was investigated by X-ray diffraction (XRD) at room temperature (RT). The XRD patterns confirmed the presence of the rhombohedral phase in all the samples. The electrical properties of the present NBT-based samples were investigated by complex impedance and the modulus spectroscopy technique in the temperature range of RT–600 °C. The AC conductivity was found to increase with the substitution of Ba²⁺ ions to the NBT sample whereas it significantly decreased with the addition of Nd³⁺ ions. The more anion vacancies in Ba-added samples and the lower anion vacancies in Nd-added samples were found to be responsible for higher and lower conductivities, respectively.     

An investigation on the unsatisfactory rate capability of spherical LiNi<Subscript>1/3</Subscript>Co<Subscript>1/3</Subscript>Mn<Subscript>1/3</Subscript>O<Subscript>2</Subscript> particles prepared by using Na<Subscript>2</Subscript>CO<Subscript>3</Subscript> as a precipitant

Spherical LiNi_1/3Co_1/3Mn_1/3O₂ particles were successfully synthesized using Na₂CO₃ as a precipitant. Electrochemical measurements indicate that the as-synthesized spherical particles deliver a high reversible capacity of above 180 mAh g^?1 at 0.1 C in the voltage range of 2.8–4.4 V and display an excellent cyclic performance at 0.5 C. However, unsatisfactory rate capability was detected for the as-prepared spherical particles. The reason for the unsatisfactory rate capability was investigated through a comparison of the properties of the as-synthesized spherical particles versus the ball-milled samples via a combination of specific surface areas test, electronic conductivity measurement, and electrochemical impedance spectroscopy. The results show that both the rate capabilities of cathode materials and the electronic conductivities of the mixtures of active material, conductive additive, and binder are highly improved when the secondary spherical particles were broken, indicating that the poor electronic conductivity of electrode caused by the large secondary spherical particles with a great amount of nano-pores is a significant factor for the unsatisfactory rate capability.     

Lithium diffusion in Li<Subscript>3</Subscript>V<Subscript>2</Subscript>(PO<Subscript>4</Subscript>)<Subscript>3</Subscript>-based electrodes: a joint analysis of electrochemical impedance,cyclic voltammetry,pulse chronoamperometry,and chronopotentiometry data

In order to establish the mechanism and to determine the parameters of lithium transport in electrodes based on lithium-vanadium phosphate (Li₃V₂(PO₄)₃), the kinetic model was designed and experimentally tested for joint analysis of electrochemical impedance (EIS), cyclic voltammetry (CV), pulse chronoamperometry (PITT), and chronopotentiometry (GITT) data. It comprises the stages of sequential lithium-ion transfer in the surface layer and the bulk of electrode material’s particles, including accumulation of lithium in the bulk. Transfer processes at both sites are of diffusion nature and differ significantly, both by temporal (characteristic time, τ) and kinetic (diffusion coefficient, D) constants. PITT data analysis provided the following D values for the predominantly lithiated and delithiated forms of the intercalation material: 10^?9 and 3 × 10^?10 cm² s^?1, respectively, for transfer in the bulk and 10^?12 cm² s^?1 for transfer in the thin surface layer of material’s particles. D values extracted from GITT data are in consistency with those obtained from PITT: 3.5–5.8 × 10^?10 and 0.9–5 × 10^?10 cm² s^?1 (for the current and currentless mode, respectively). The D values obtained from EIS data were 5.5 × 10^?10 cm² s^?1 for lithiated (at a potential of 3.5 V) and 2.3 × 10^?9 cm² s^?1 for delithiated (at a potential 4.1 V) forms. CV evaluation gave close results: 3 × 10^?11 cm² s^?1 for anodic and 3.4 × 10^?11 cm² s^?1 for cathodic processes, respectively. The use of complex experimental measurement procedure for combined application of the EIS, PITT, and GITT methods allowed to obtain thermodynamic E,c dependence of Li₃V₂(PO₄)₃ electrode, which is not affected by polarization and heterogeneity of lithium concentration in the intercalate.     

Nanocrystalline Li<Subscript>2</Subscript>TiO<Subscript>3</Subscript> electrodes for supercapattery application

Nanocrystalline Li₂TiO₃ was successfully synthesized using solid-state reaction method. The microstructural and electrochemical properties of the prepared material are systematically characterized. The X-ray diffraction pattern of the prepared material exhibits predominant (002) orientation related to the monoclinic structure with C2/c space group. HRTEM images and SAED analysis reveal the well-developed nanostructured particles with average size of ～40 nm. The electrochemical properties of the prepared sample are carried out using cyclic voltammetry (CV) and chronopotentiometry (CP) using Pt//Li₂TiO₃ cell in 1 mol L^?1 Li₂SO₄ aqueous electrolyte. The Li₂TiO₃ electrode exhibits a specific discharge capacity of 122 mAh g^?1; it can be used as anode in Li battery within the potential window 0.0–1.0 V, while investigated as a supercapacitor electrode, it delivers a specific capacitance of 317 F g^?1 at a current density of 1 mA g^?1 within the potential range ?0.4 to +0.4 V. The demonstration of both anodic and supercapacitor behavior concludes that the nanocrystalline Li₂TiO₃ is a suitable electrode material for supercapattery application.     

Magnetoelectric Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> and relativity theory

Based on the dielectric continuum phonon model, uniaxialmodel and force balance equation the mobility of two dimensional electrongas in wurtzite Al_xGa_1-xN/GaN/Al_xGa_1-xN quantum wells isdiscussed theoretically within the temperature range dominated by opticalphonons. The dependences of the electron mobility on temperature, Al molarfraction and electron sheet density are presented including hydrostaticpressure effect. The built-in electric field is also taken into account. Itis found that under normal pressure the main contribution to the mobility isfrom the scattering of interface optical phonons in narrow (for well widthd < 12 Å) and wide (for d > 117 Å and d > 65 Å for finitelythick barriers and infinitely thick ones, respectively) wells, whereas thatis from the scattering of confined optical phonons in a well with anintermediate width. It is shown that the electron mobility decreases withincreasing Al molar fraction and temperature, whereas increases obviouslywith increasing electron sheet density. The theoretical calculated electronmobility is 978 cm²/V?s which is higher than an available experimentaldata 875 cm²/V?s when x equals to 0.58 at room temperature. Theresults under hydrostatic pressure considering the modification of strainindicate that the mobility increases slightly as hydrostatic pressureincreases from 0 to 10 GPa.