On the inverse miniemulsion copolymerization and terpolymerization of acrylamide, <Emphasis Type="Italic">N,N′</Emphasis>-methylenebis(acrylamide) and methacrylic acid

The kinetics of free-radical copolymerization and terpolymerization of acrylamide (AAm), N, N′-methylenebis(acrylamide) (MBA) and methacrylic acid (MA) in the inverse water/monomer/cyclohexane/Tween 85 miniemulsion was investigated. Polymerizable sterically-stable miniemulsions were formulated in cyclohexane as a continuous medium. Polymerizations are very fast and reach the final conversion within several minutes. The dependence of the polymerization rate vs. conversion is described by a curve with two nonstationary rate intervals. The maximum rate of polymerization slightly increases with increasing concentration of crosslinking monomer (MBA) and strongly decreases by the addition of MA. The rate of polymerization is inversely proportional to the 0.9 ^th and 1.8 ^th power of the particle concentration without and with MA, respectively. The number of polymer particles is inversely proportional to the 0.18 ^th and 0.13 ^th power of MBA concentration. The kinetic and colloidal parameters of the miniemulsion polymerization are discussed in terms of microemulsion polymerization model.     

Adsorption of<Emphasis Type="Italic"> N</Emphasis>-dodecyl-<Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-dimethyl-3-ammonio-1-propanesulfonate (DDAPS), a model zwitterionic surfactant,on the Au(111) electrode surface

Electrochemical measurements including cyclic voltammetry, differential capacity, and chronocoulometry have been used to characterize the adsorption behaviors of the zwitterionic surfactant N-dodecyl-N,N-dimethyl-3-ammonio-1-propanesulfonate (DDAPS) on the Au(111) electrode surface. The thermodynamics of the ideally polarized electrode have been employed to determine the Gibbs excess and the Gibbs energy of adsorption. The results show that the adsorption of DDAPS has a multistate character. The first two states are observed at potentials close to zero charge. At low bulk DDAPS concentrations, it corresponds to the formation of a film of nearly flat adsorbed molecules. At higher concentrations it is converted into a hemimicellar state. The second state is formed at negative potentials and charge densities close to 0 C cm^–2. It corresponds to a film of tilted molecules oriented with the hydrocarbon tail towards the metal and the polar head toward the solution.Dedicated to Professor Zbigniew Galus on the occasion of his 70^th birthday and in recognition of his many contributions to electrochemistry.     

<Superscript>1</Superscript>H NMR spectra of water contained in solutions of poly(<Emphasis Type="Italic">N</Emphasis>-vinylpyrrolidone) and its modification products in CDCl<Subscript>3</Subscript>

¹H NMR spectra in CDCl₃ of poly(N-vinylpyrrolidone), epoxidized poly(N-vinyl-pyrrolidone), and products derived from the latter by modification with amino acids (glycine, β-alanine, γ-aminobutyric acid, and ε-aminocaproic acid) were examined. The ¹H NMR spectra of the modified polymers contain signals for water protons due to different centers of water sorption. These signals differ in chemical shift and integral intensity and indicate a changed spatial packing of the polymer as the result of its modification. Published in Russian in Izvestiya Akademii Nauk. Seriya Khimicheskaya, No. 10, pp. 2377–2380, October, 2005.     

Synthesis of amphiphilic diblock copolymers poly[2-(<Emphasis Type="Italic">N</Emphasis>, <Emphasis Type="Italic">N</Emphasis>-dimethylamino)ethyl methacrylate]-<Emphasis Type="Italic">b</Emphasis>-poly(stearyl methacrylate) and their self-assembly in mixed solvent

Amphiphilic diblock copolymers consisting of 2-(N, N-dimethylamino)ethyl methacrylate (DMAEMA, abbreviated as DMA) and stearyl methacrylate (SMA) with different degrees of polymerization and compositions were prepared by reversible addition–fragmentation chain transfer (RAFT) copolymerization. The composition and chemical structures of (co)polymers were confirmed by the measurements of ¹H NMR spectroscopy and gel permeation chromatography (GPC). The self-aggregating structures of amphiphilic diblock copolymers with the concentration of 0.1~0.3 wt.% in THF/water mixed solvent was investigated by transmission electron microscopy (TEM) and dynamic light scattering (DLS). It was found that both the morphologies and aggregating particle size resulted from the amphiphilic diblock copolymers depended on the variation of pH values, the lengths of the hydrophobic PSMA chains, and the weight ratio of THF/water mixed solvent.     

Determination of epoxides by high-performance liquid chromatography following derivatization with <Emphasis Type="Italic">N</Emphasis>,<Emphasis Type="Italic">N</Emphasis>-diethyldithiocarbamate

A reversed-phase, high-performance liquid chromatography (RP-HPLC) method that allows quantitation of low levels of epoxides has been described. The method involved derivatization of epoxides using 100- to 1,000-fold excess N,N-diethyldithiocarbamate (DTC) at 60 °C for 20 min at neutral pH. The unreacted DTC was then decomposed to CS₂ and diethyl amine by acidification of the reaction mixture to pH 2 using orthophosphoric acid. The first two steps could be performed in the same reaction vessel by sequential addition of reagents. In the final step, an aliquot (20 μL) of the derivatized sample was analyzed for the presence of stable esters of DTC by RP-HPLC using a Supelcosil LC-18-S (150 × 4.6-mm) column and a mobile phase consisting of 40% (v/v) acetonitrile in water at a flow of 1 mL min⁻¹. Using UV detection at 278 nm, the epoxides gave linear responses in the concentration range of 0.25 to 50 μM. The method is robust, and as low as 5 pmol of the analyte could be successfully detected and quantified with recoveries of ≥94%. Following a minimal pretreatment such as ultrafiltration (molecular weight cutoff 5,000 Da), the method is suitable for analysis of epoxides in complex physiological fluids (e.g., fetal bovine serum). The method has been rigorously evaluated and adapted in our laboratory for routine analysis and determination of stability of epoxides of 1,3-butadiene and other alkenes added to cell cultures.     

A small-angle neutron scattering study of the ethyl (n-octyl) phosphate micelles in water

Summary Mixed-double chain anionic surfactants, barium- and lithium-salts of ethyl(n-octyl) phosphate (EOP), which are asymmetric in the molecular shape, and a series of identical chain di-n-alkyl phosphate lithium salts have been synthezized. The limiting partial molar volume of a PO ₄ ^– group (23.43±0.41 cm³ mol^–1) for use in small-angle neutron scattering analysis was determined by density measurements of a series of identical chain di-n-alkyl phosphate lithium salts. For lithium EOP-D₂O system, a critical micellar concentration (2.3 wt%) was determined by³¹P NMR spectra. The micellar shape and size in the EOP-water binary system has been investigated by using small-angle neutron scattering (SANS) spectra. It has been found that the micelles of barium EOP in water have the shape of a prolate spheroid and aggregation numbers (n) equal to 48 at 23°C and 52 at 50°C. For the lithium EOP-micellar system, it has been found that the minimum micelle with an aggregation numbern=21 is spherical and micellar growth and variation from the spherical to the prolate shape might occur with an increase in concen tration above the CMC.     

Synthesis,structural and conformational study of selected <Emphasis Type="Italic">N</Emphasis>-substituted phthalimides

This paper synthesizes N-substituted phthalimides derived from nitrogen heterocycles as potential 5-HT₄ ligands by using the Mitsunobu reaction. Conformational studies of some of the new compounds have been conducted using ¹H and ¹³C-NMR spectroscopy. Proton and carbon resonances were achieved through the application of one-dimensional selective NOE, two-dimensional NMR techniques-homonuclear COSY-45, NOESY and heteronuclear ¹H-¹³C HMQC correlated spectroscopy- and double resonance experiments. The crystal structure of compound 1 was determined by X-ray diffraction.     

Detection of <Emphasis Type="Italic">N</Emphasis>-monomethyl-lysine generated by metabolic transmethylation

Administration of radiolabelled deprenyl to rats resulted in the urinary elimination of a ¹⁴C-labelled N-monomethyl-lysine. An increased level of N-monomethyl-lysine was found following an oral dose of another drug, also containing an N-methyl group. The urine sample was treated with 9-fluorenylmethoxycarbonyl chloride and then subjected to high-performance liquid chromatography (HPLC); the radioactive fraction was identified as N-monomethyl-lysine by using HPLC-MS in electrospray mode. Identification of N-monomethyl-lysine in the radioactive fraction gives experimental proof of transmethylation from a well-known drug to an endogenous compound.     

Using the reversible addition–fragmentation chain transfer process to synthesize core‐crosslinked micelles

Poly(2‐hydroxyethyl acrylate)–poly(n‐butyl acrylate) block copolymers were synthesized with the reversible addition–fragmentation chain transfer (RAFT) process. The block copolymers were synthesized successfully with either poly(2‐hydroxyethyl acrylate) or poly(n‐butyl acrylate) macro‐RAFT agents. The resulting block copolymers had narrow molecular weight distributions (polydispersity index = 1.3–1.4). Copolymer self‐aggregation in water yielded micelles, with the hydrodynamic diameter (D_h) values of the aggregates dependent on the length of both blocks according to D_h ～ N_BA^1.17N_HEA^0.57, where N_BA is the number of repeating units of n‐butyl acrylate and N_HEA is the number of repeating units of 2‐hydroxyethyl acrylate. The micelles were subsequently stabilized via chain extension of the block copolymer with a crosslinking agent. The successful chain extension in a micellar system was confirmed by an increase in the molecular weight, which was detected with membrane osmometry. The crosslinked particles showed noticeably different aggregation behavior in diverse solvent systems. The uncrosslinked micelles formed by the block copolymer (N_HEA = 260, N_BA = 75) displayed a definite critical micelle concentration at 5.4 × 10^?4 g L^?1 in aqueous solutions. However, upon crosslinking, the critical micelle concentration transition became obscure. © 2006Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2177–2194, 2006     

Interfacial and aggregation properties of aqueous sodium <Emphasis Type="Italic">N</Emphasis>-dodecanoylsarcosinate solutions at different pH

The pH dependence of an anionic surfactant, sodium N-dodecanoylsarcosinate (SLAS), has been studied by measuring interfacial tension, fluorescence, dynamic light scattering, etc., in aqueous solutions with phosphate and borate buffers. The interfacial tension (γ) of SLAS decreases remarkably with a pH decrease and is constant at pH > 7.3. The observed values for the critical micelle concentration (cmc) and the surfactant concentration at which its γ value is reduced by 20 mN/m from that of pure water (C ₂₀) decrease with a pH decrease, while those also become constant at pH > 6.5 and >7.3, respectively. On the other hand, the interfacial excess of SLAS increases at pH < 7.3. These interfacial behaviors have been further investigated by the addition of Tl⁺ which replaces Na⁺ of SLAS. The observed γ values of LAS⁻ with the different counter cations are in the order of H⁺ < Tl⁺ < Na⁺. In order to reveal aggregation properties of SLAS, the aggregation number (N _agg), the micropolarity, the hydrodynamic radius (R _h) of micelle, and the fluorescence anisotropy of Rhodamine B (r) have been evaluated at various pHs. The N _agg value shows a decreasing tendency with a pH increase. The I ₁/I ₃ ratio and the R _h values do not strongly depend on pH. The r value decreases until pH 7 and remains constant at pH > 7.0. These interfacial and micelle properties have been discussed in detail considering the electrostatic interaction and the molecular structures of the hydrophilic headgroup.     

Voltammetric determination of the trace amounts of bromate in drinking water after pre-concentration on hydrous γ-Al<Subscript>2</Subscript>O<Subscript>3</Subscript>

A differential pulse voltammetric (DPV) method for the determination of bromate in drinking water, after pre-concentration on γ-Al₂O₃, is proposed. The reduction peak of bromate has been observed at the potential E _p -−1.6 V in an ammonia buffer as a supporting electrolyte. The method has been successfully applied to determine a bromate concentration of 2.5 μg·l⁻¹ in drinking water (RSD=6.1%, n=7). A sample pre-treatment with a column filled with mixed cation-exchange resin in Ag, Ba and H forms was needed before pre-concentration of bromate on alumina.     

Volume phase transition and structure of poly(N-isopropylacrylamide) microgels studied with 1H-NMR spectroscopy in D2O

Thermoresponsive colloidal microgels were prepared by polymerisation of N-isopropylacrylamide (NIPAM) with varying concentration of a cross-linking monomer, N,N-methylenebisacrylamide (MBA), in water with either 0.4 or 6.7 mM concentration of an anionic surfactant, sodium dodecylsulphate (SDS). Volume phase transitions of the prepared microgels were studied in D₂O by ¹H-NMR spectroscopy including the measurements of spin–lattice (T1) and spin–spin (T2) relaxation times for the protons of poly(N-isopropylacrylamide) (PNIPAM) at temperature range 22–50 °C. In addition, microcalorimetry, turbidometry, dynamic light scattering and electrophoretic mobility measurements were used to characterise the aqueous microgels. The results from the different characterisation methods indicated that PNIPAM microgels prepared in 6.7 mM SDS concentration are structurally different compared to their correspondences prepared in 0.4 mM concentration. Increasing MBA concentration in the microgel synthesis appears to increase the structural heterogeneity in both cases of SDS concentration. PNIPAM structures with significantly higher molecular mobilities at temperatures above 35 °C were observed in the microgels prepared in 0.4 mM SDS concentration, as indicated by the ¹H NMR relaxation times of different PNIPAM protons. We conclude that the high mobilities measured with NMR at elevated temperatures and also the clearly negative values of zeta potential are in connection to a fairly mobile surface layer with polyelectrolyte nature and a consequent high local lower critical solution temperature.     

Intensification of Biocatalytical Processes by Synergistic Substrate Conversion. Fungal Peroxidase Catalyzed <Emphasis Type="Italic">N</Emphasis>-Hydroxy Derivative Oxidation in Presence of 10-Propyl Sulfonic Acid Phenoxazine

Many industrial pollutants, xenobiotics, and industry-important compounds are known to be oxidized by peroxidases. It has been shown that highly efficient peroxidase substrates are able to enhance the oxidation of low reactive substrate by acting as mediators. To explore this effect, the oxidation of two N-hydroxy derivatives, i.e., N-hydroxy-N-phenyl-acetamide (HPA) and N-hydroxy-N-phenyl-carbamic acid methyl ester (HPCM) catalyzed by recombinant Coprinus cinereus (rCiP) peroxidase has been studied in presence of efficient substrate 3-(4a,10a-dihydro- phenoxazin-10-yl)-propane-1-sulfonic acid (PPSA) at pH 8.5. The bimolecular constant of PPSA cation radical reaction with HPA was estimated to be (2.5 ± 0.2)·10⁷ M⁻¹ s⁻¹ and for HPCM was even higher. The kinetic measurements show that rCiP-catalyzed oxidation of HPA and HPCM can increase up to 33,000 times and 5,500 times in the presence of equivalent concentration of high reactive substrate PPSA. The mathematical model of synergistic rCiP-catalyzed HPA–PPSA and HPCM–PPSA oxidation was proposed. Experimentally obtained rate constants were in good agreement with those calculated from the model confirming the synergistic scheme of the substrate oxidation. In order to explain the different reactivity of substrates, the docking of substrates in the active site of the enzyme was calculated. Molecular dynamic calculations show that the enzyme–substrate complexes are structurally stable. The high reactive PPSA exhibited higher affinity to enzyme active site than HPA and HPCM. Furthermore, the orientation of HPA and HPCM was not favorable for proton transfer to the distal histidine, and different substrate reactivity was explained by these diversities.     

Controlled hydrophobic/hydrophilic chitosan: colloidal phenomena and nanosphere formation

N-Phthaloylchitosan-grafted poly(ethylene glycol) methyl ether (mPEG) gives a milky solution when dispersed in water and a series of solvents. The appearance of turbidity depends on the types of solvents, i.e., protic and aprotic solvents. N-Phthaloylchitosan-grafted mPEG shows an aggregation of sphere-like particles as observed by scanning electron microscopy. Transmission electron microscopy indicates that the spheres are at the nano level. When the chain length of mPEG is as high as 5×10³ Da the sphere size becomes as small as 80–100 nm on average as observed by transmission electron microscopy. By simply adjusting the hydrophobicity/hydrophilicity of the chitosan chain, a stable nanosphere can be obtained directly.     

Bacteriophage-amplified bioluminescent sensing of <Emphasis Type="Italic">Escherichia coli</Emphasis> O157:H7

Escherichia coli O157:H7 remains a continuous public health threat, appearing in meats, water, fruit juices, milk, cheese, and vegetables, where its ingestion at concentrations of perhaps as low as 10 to 100 organisms can result in potent toxin exposure and severe damage to the lining of the intestine. Abdominal pain and diarrhea develop, which in the very young or elderly can progress towards hemolytic uremic syndrome and kidney failure. To assist in the detection of E. coli O157:H7, a recombinant bacteriophage reporter was developed that uses quorum sensing (luxI/luxR) signaling and luxCDABE-based bioluminescent bioreporter sensing to specifically and autonomously respond to O157:H7 serotype E. coli. The bacteriophage reporter, derived from phage PP01, was tested in artificially contaminated foodstuffs including apple juice, tap water, ground beef, and spinach leaf rinsates. In apple juice, detection of E. coli O157:H7 at original inoculums of 1 CFU mL⁻¹ occurred within approximately 16 h after a 6-h pre-incubation, detection of 1 CFU mL⁻¹ in tap water occurred within approximately 6.5 h after a 6-h pre-incubation, and detection in spinach leaf rinsates using a real-time Xenogen IVIS imaging system resulted in detection of 1 CFU mL⁻¹ within approximately 4 h after a 2-h pre-incubation. Detection in ground beef was not successful, however, presumably due to the natural occurrence of quorum sensing autoinducer (N-3-(oxohexanoyl)-l-homoserine lactone; OHHL), which generated false-positive bioreporter signals in the ground beef samples.     

Synthesis and self-assembly of comb-like amphiphilic copolymer poly(maleic anhydride-<Emphasis Type="Italic">alt</Emphasis>-stearyl methacrylate)-<Emphasis Type="Italic">b</Emphasis>-poly(stearyl methacrylate)

Comb-like amphiphilic block copolymers of maleic anhydride (MA) and stearyl methacrylate (SMA) were prepared through the reversible-addition-fragmentation-transfer polymerization. The resultant copolymers were characterized by gel permeation chromatograph and ¹H NMR. The aggregation behaviors of P(MA-alt-SMA)-b-PSMA were investigated in tetrahydrofuran/water. It is of great interest that the aggregates with different morphologies and dimensions could be obtained by adjusting the polymer concentration, water content, and pH. The dimension and structure of these aggregates were investigated by transmission electron microscopy and dynamic light scattering. The effect of the copolymer–solvent interaction on these aggregations was discussed.     

Thallium-205 NMR spectroscopy. Solvation of the thallous ion in dilute aqueous-amide and amide-amide binary solvent systems of formamide,N-methylformamide,andN-ethylformamide

Solvation of the thallous ion in dilute solutions of six binary solvent systems (formamide/water,N-methylformamide/water,N-ethylformamide/water, formamide/N-methylformamide, formamide/N-ethylformamide, andN-methylformamide/N-ethylformamide) was studied with²⁰⁵Tl NMR spectroscopy. An attempt was made to separate solvation effects related to the electrondonating ability (Lewis basicity) of the solvents from effects resulting from structural changes in the solvation sphere. Structural effects were found to be greatest in theN-methylformamide/water system and least in theN-methylformamide/formamide system.     

Synthesis and characterization of alkylated N‐vinylformamide monomers and their polymers

N‐alkyl‐N‐vinylformamide monomers (alkyl: n‐butyl, hexyl, decyl, and dodecyl) are synthesized in two steps: first, preparation of N‐vinylformamide potassium salt by the reaction of N‐vinylformamide (NVF) with potassium t‐butoxide, then reaction with alkyl bromide. All four monomers are liquid and are characterized by IR, ¹H NMR, ¹³C NMR, and mass spectra. They exist as rotomers in solution and a 2D NOE experiment on the N‐hexyl containing polymer shows the E isomer to be favored. The polymerizability of the four monomers is from good to fair, depending upon the length of alkyl chain on the N‐atom‐‐the longer the chain length, the lower lower the polymerizability of monomer. The hydrolysis of poly(N‐hexyl‐N‐vinylformamide) and poly(N‐dodecyl‐N‐vinylformamide) under acidic and basic conditions was examined. Studies show that hydrolytic cleavage of formyl groups of poly (N‐alkylated‐N‐vinylformamide) depends on the hydrophobicity of the alkyl substituent on the N‐atom under acidic conditions; both polymers were hydrolyzed to only a minor extent under alkaline conditions. The N‐alkylated monomers can copolymerize with NVF and demonstrate amphiphilic properties. The copolymers demonstrate a critical aggregation concentration above which they can solubilize a water insoluble dye; the N‐hexyl containing copolymer stabilizes a castor oil‐in‐water emulsion. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 4994–5004, 2004     

Convenient synthesis and NMR spectral studies of variously substituted <Emphasis Type="Italic">N</Emphasis>-methylpiperidin-4-one-<Emphasis Type="Italic">O</Emphasis>-benzyloximes

Abstract  A series of variously substituted N-methylpiperidin-4-one-O-benzyloximes were synthesized by three different methods. Among them, the direct conversion of 2,6-diarylpiperidin-4-ones into the corresponding oxime ethers (method A) was proved to be better than the other two methods in the sense of good yield, convenience, easy work-up and quick reaction time. All the synthesized compounds are characterized by IR, Mass and NMR (¹H NMR, ¹³C NMR, ¹H-¹H COSY, ¹H-¹³C COSY and HMBC) spectral studies. The conformational preference of the synthesized oxime ethers with/without alkyl and aryl substituents at C-3/C-5 and C-2/C-6 is discussed using the spectral data. The observed chemical shifts and coupling constants suggest that the synthesized oxime ethers adopt chair conformation with equatorial orientation of all the substituents, whereas 1-methyl-3-isopropyl-2,6-diphenylpiperidin-4-one-O-benzyloxime also exists in boat conformation. Based on the NMR data, the effects of oximination on ring carbons and their associated protons and alkyl substituents are discussed. In addition, the effect of NMe group on the 2,6-diarylpiperidin-4-one-O-benzyloximes was also studied. Graphical abstract        

Synthesis and self‐assembling of poly(N‐isopropylacrylamide‐block‐poly(L‐lactide)‐block‐poly(N‐isopropylacrylamide) triblock copolymers prepared by combination of ring‐opening polymerization and atom transfer radical polymerization

Novel thermo‐responsive poly(N‐isopropylacrylamide)‐block‐poly(l ‐lactide)‐block‐poly(N‐isopropylacylamide) (PNIPAAm‐b‐PLLA‐b‐PNIPAAm) triblock copolymers were successfully prepared by atom transfer radical polymerization of NIPAAm with Br‐PLLA‐Br macroinitiator, using a CuCl/tris(2‐dimethylaminoethyl) amine (Me₆TREN) complex as catalyst at 25 °C in a N,N‐dimethylformamide/water mixture. The molecular weight of the copolymers ranges from 18,000 to 38,000 g mol^?1, and the dispersity from 1.10 to 1.28. Micelles are formed by self‐assembly of copolymers in aqueous medium at room temperature, as evidenced by ¹H NMR, dynamic light scattering (DLS) and transmission electron microscopy (TEM). The critical micelle concentration determined by fluorescence spectroscopy ranges from 0.0077 to 0.016 mg mL^?1. ¹H NMR analysis in selective solvents confirmed the core‐shell structure of micelles. The copolymers exhibit a lower critical solution temperature (LCST) between 32.1 and 32.8 °C. The micelles are spherical in shape with a mean diameter between 31.4 and 83.3 nm, as determined by TEM and DLS. When the temperature is raised above the LCST, micelle size increases at high copolymer concentrations due to aggregation. In contrast, at low copolymer concentrations, decrease of micelle size is observed due to collapse of PNIPAAm chains. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 3274–3283