Molecular Composition of Nonionic Vesicles Prepared from Span 80 or Span 85 by a Two‐Step Emulsification Method

The molecular compositions of the commercial nonionic surfactants Span 80 and Span 85 were analyzed by reversed phase high performance liquid chromatography (HPLC). Both surfactants are mixtures of fatty acid esters, containing monoesters, diesters, triesters, and tetraesters. While diesters dominate in the case of Span 80, Span 85 contains mainly tetraesters. Vesicles were prepared from Span 80 (or Span 85) by a two‐step emulsification method that involved homogenization and separation steps in which a portion of the surfactants was removed. The composition of the vesicles was analyzed by HPLC with respect to the different esters present. Although commercial Span 80 and Span 85 differ considerably in their molecular compositions, the ester profiles of the vesicles formed were in both cases rather similar and dominated by diesters. Therefore, the particular vesicle preparation method leads to a molecular selection of mainly those components that are prone to form bilayers.     

Preparation of Water-in-Diesel Fuel Nanoemulsions Using High-Energy Emulsification Method and a Study of Some of Their Surface Active Properties

In this work, formations of water-in-diesel fuel nanoemulsions using water/mixed nonionic surfactant/diesel fuel system has been studied. The high-energy emulsification method was used to form three emulsions using different water contents: 5, 10, and 14% (v/v) namely; E1, E2, and E3, respectively. These nanoemulsions were stabilized with emulsifiers having different hydrophilic lipophilic balance (HLB), namely, Span 80 (HLB = 4.3), Emarol 85 (HLB = 11), and their mixture (SE) with HLB = 10. The effect of water on the droplet size formation has been investigated. The interfacial tension and thermodynamic properties of the individual and emulsifiers blends have been studied. The interfacial tension (γ) measurements at 30°C were used to determine the critical micelle concentration (CMC) and surface active properties of these emulsifiers. The water droplet sizes were measured by dynamic light scattering (DLS). From the obtained data, it was found that mean sizes between 19.3 and 39 nm were obtained depending on the water content and concentration of blend emulsifiers (SE). Also, the results show that the interfacial tension (γ) gives minimum value (10.85 mN/m) for SE comparing with individual emulsifier (17.13 and 12.77 mN/m) for Span 80 and Emarol 85, respectively. The visual inspection by transmission electron microscopy showed that the obtained results support the data obtained by dynamic light scattering.     

Flow Injection Analysis System Using Magnetic Beads,Screen Printed Electrodes and Magnets

Here is presented a Flow Injection Analysis (FIA) system using a flow cell with an integrated magnet, applied to biotin determination. The mixture of magnetic beads modified with streptavidin (Strep‐MB), biotin and B‐HRP is left 15 minutes under stirring and then a washing step is performed in an automatic way thanks to the external magnets coupled in the FIA system. After the immobilization of the MBs on the surface of the electrode, 3,3′,5,5′‐Tetramethylbenzidine (TMB) is injected. The linear range obtained is between 0.5 to 10 pM of biotin and the sensitivity is 85 nA/pM.     

Acrylamide as cosurfactant and hydrotrope in the pseudoternary Span 80-Tween 85/isopar M/water emulsion/microemulsion forming system

The aim of this study was to investigate the effects of acrylamide on emulsification of the pseudoternary Span 80-Tween 85/isopar M/water system at 40 °C. It was revealed that acrylamide could act as a surface-active agent to decrease the isopar M/water interfacial tension, and as a hydrotrope to increase the aqueous solubility of Tween 85, and further remarkably influence the emulsification of the investigated pseudoternary Span 80-Tween 85/isopar M/water system. The surface-active role of acrylamide could reduce the minimal weight fraction of the mixture of Span 80 and Tween 85 in pseudoternary systems (X_ST) to form stable water-in-oil (W/O) emulsions when the weight fraction of acrylamide in the aqueous domain (X_AM) is below 0.1; while its hydrotropic role at high X_AM levels (>0.1) could drive more Tween 85 molecules to transfer into aqueous phase and slightly improved the minimal X_ST to form stable W/O emulsions, as compared to that of X_AM at 0.1. Moreover, under a given X_ST, the mean diameter of the droplet size distribution of the W/O emulsion remarkably decreased with the increase in X_AM; while the smaller droplets in the W/O emulsion systems at higher level of X_AM still coalesced rapidly when the compositions of the emulsion was slightly above the visually determined boundary between non-emulsion and stable emulsion regions.     

Span 80 vesicles have a more fluid, flexible and "wet" surface than phospholipid liposomes

The surface properties of Span 80 vesicles at various cholesterol contents, together with those of various liposomes, were characterized by using fluorescence probes. The membrane fluidity of the Span 80 vesicles was measured by 1,6-diphenyl-1.3.5-hexatriene (DPH) and trimethlyammonium-DPH (TMA-DPH), and the results suggested that the surface of the Span 80 vesicles was fluid due to the lateral diffusion of Span 80 molecules. The depolarization measured by TMA-DPH and the headgroup mobility measured by dielectric dispersion analysis indicated the high mobility of the head group of Span 80 vesicles. This suggested that the surface of Span 80 vesicles was flexible due to the head group structure of Span 80, sorbitol. In addition, spectrophotometric analysis with 6-dodecanoyl-N, N-dimethyl-2-naphthylamine and 8-anilino-1-naphthalenesulfonic acid indicated that the water molecules could easily invade into the interior of the Span 80 vesicle membrane, suggesting that the membrane surface was more wet than the liposome surface. These surface properties indicated that the protein could interact with the interior of vesicle membranes, which was similar to the case of cholesterol. Thus the present results confirmed that the Span 80 vesicle surfaces showed the unique characteristics of fluidity, flexibility, and "wetness", whereas the liposome surfaces did not.     

Application of liquid chromatography in polymer non-ionic antistatic additives analysis

This article investigates the applicability of HPLC-UV, ultra performance LC-evaporative light-scattering detection (UPLC-ELSD), HPLC-ESI(+)-MS and HPLC-hybrid linear ion trap (LTQ) Orbitrap MS for the analysis of different non-ionic antistatic additives, Span 20, Span 60, Span 65, Span 80, Span 85 (sorbitan fatty acid esters), Atmer 129 (glycerol fatty acid ester) and Atmer 163 (ethoxylated alkylamine). Several alkyl chain length or different degrees of esterification of polyol derivatives can be present in commercial mixtures of these polymer additives. Therefore, their identification and quantification is complicated. Qualitative composition of the studied compounds was analysed by MS. HPLC-UV, UPLC-ELSD and HPLC-LTQ Orbitrap MS methods were applied to the quantitative determination of the different Spans, Atmer 129 and Atmer 163, respectively. Quality parameters of these methods were established and no derivatization was necessary.     

Iron cross-linked carboxymethyl cellulose—gelatin complex coacervate beads for sustained drug delivery

The formation and smooth recovery of ibuprofen encapsulated in microcapsules using gelatin and carboxymethyl cellulose (CMC) complex coacervation without glutaraldehyde were the objectives of this investigation. The microcapsules were recovered as ionically cross-linked beads using aqueous ferric chloride in 50 vol.% of 2-propanol. A physical mixture of CMC/gelatin (FP1) and CMC alone (FP2) beads was also prepared for comparison. The drug-entrapment efficiency of complex coacervate beads (FP3-FP5) was dependent on the drug-to-polymer ratio and was in the range of 86–92 mass %. Beads prepared with the highest ratio of the drug (FP5) exhibited the lowest entrapment. FP1 and FP2 beads exhibited an entrapment efficiency of 98.5 mass % and 91.3 mass %, respectively. Infrared spectroscopy (FTIR) revealed different functional groups in complex coacervate, physical mixture and FP2 beads. Optical and scanning electron microscopy revealed the distinct appearance and surface morphology of the various beads. The stable and crystalline nature of ibuprofen in the beads was confirmed by FTIR and differential scanning calorimetry (DSC), respectively. Ibuprofen release from FP1 and FP2 beads was very slow and unsuitable for oral delivery. The bead prepared by complex coacervation (FP5) showed a better release profile over 48 h and could be developed as a sustained drug delivery system.     

Aerosol assisted synthesis of silica/phenolic resin composite mesoporous hollow spheres

Hollow spheres of phenolic resin/silica composite are synthesized by macroscopic phase separation of a sorbitan monooleate surfactant Span 80 during aerosol-assisted spraying. The cavity can be evolved from multiple compartments to single hollow cavity with the increase of Span 80 content. The composite shell becomes mesoporous due to the release of small molecules after thermal treatment above 350 °C. After further thermal treatment at a higher temperature for example 900 °C in nitrogen or 1,450 °C in argon, the carbon/silica composite hollow spheres or crystalline silicon carbide hollow spheres are derived, respectively. Compared to the pure phenolic resin-based carbon spheres, thermal stability of the carbon-based composite spheres in air is essentially improved by the introduction of inorganic component silica. The carbon-based composite hollow spheres combine both performances of easy mass transportation through macropores and high specific surface area of mesopores, which will be promising to support catalysts for fuel cells. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Cationic liposomes modified with non-ionic surfactants as effective non-viral carrier for gene transfer

A defined change in formulation components affects the physical and chemical characteristics of cationic liposomes (CLs) carriers in many ways. Therefore, a great degree of control can be exercised over the structure by modifying the CLs with various materials, leading to new innovations for carrier improvement. In the present study, surface modifications of cationic liposomes with non-ionic surfactants—sorbitan monoesters serials (Span 85, 80, 40 and 20) were carried out for developing a new gene transfer carrier. Span modified cationic liposomes (Sp-CLs) were prepared by reverse phase evaporation method (RPV) and self-assemble complexes of antisense oligonucleotides/surfactant modifying cationic liposomes were prepared by auto-coacervation through electrostatic effect. Characterization of Sp-CLs and the self-assembled complex was performed by electron microscope, particle size, zeta potential, turbidity and agarose electrophoresis. Furthermore, in vitro cellular uptake experiment showed that Span plays a role in enhancing the cellular uptake of encapsulated oligonucleotides mediated by Sp-CLs by the endocytosis-dependent route. CLs modified with Span 40 significantly facilitated the cellular uptake by COS-7 cells and HeLa cells; also showed some positive effect on gene expression. That suggests it is a potential non-viral carrier for efficient gene transfer.     

Monodisperse polymer beads as packing material for high-performance liquid chromotography: Effect of divinylbenzene content on the porous and chromatographic properties of poly(styrene-co-divinylbenzene) beads prepared in presence of linear polystyrene as a porogen

The effect of concentration of divinylbenzene on pore size distribution and surface areas of micropores, mesopores, and macropores in uniformly sized porous poly(styrene-co-divinylbenzene) beads prepared in the presence of linear polystyrene as a component of the porogenic mixture has been studied. While the total specific surface area was clearly determined by the content of divinylbenzene, the sum of pore volumes for mesopores and macropores as well as their size distribution does not change within a broad range of DVB concentrations. Consequently, the size exclusion chromatography calibration curves are almost identical for all the beads prepared with different percentages of crosslinking monomer. However, the more crosslinked beads have better mechanical and hydrodynamic properties. © 1994 John Wiley & Sons, Inc.     

Distribution of Sorbitan Monooleate in poly(l-lactide-co--caprolactone) nanofibers from emulsion electrospinning

The aim of this study was to investigate the distribution of Sorbitan Monooleate (Span80) in poly(l-lactide-co--caprolactone) (PLLACL) nanofibers from emulsion electrospinning. The hypothesis was that PLLACL/Span80 nanofibrous mats would have some Span80 on the surface of the composite nanofibers. To test the hypothesis, the electrospinning of emulsions made of PLLACL, chloroform, Span80, and distilled water to prepare PLLACL/Span80 nanofibers was systematically investigated. The morphology of PLLACL/Span80 nanofibers was investigated by atomic force microscopy. The surface hydrophilicity of the nanofibrous mats were examined by water contact angle test. The distribution of Span80 on the surface of nanofibrous mats was also confirmed by the performance of pig iliac endothelium cells on the nanofibrous mats.     

带羧基单分散彩色微球的制备

采用两步活性溶胀种子聚合法, 制备了可用于免疫检测的3种不同颜色的表面带有羧基功能基的粒径在400—800 nm之间的彩色单分散微球. 先用无皂乳液聚合法制备出单分散聚苯乙烯种子, 然后用邻苯二甲酸二正丁酯(DBP)作为溶胀剂对微球进行溶胀, 溶涨后的种子模板再用混溶的苯乙烯、二乙烯苯、丙烯酸、双键彩色染料以及引发剂(BPO)溶胀, 升温聚合后得到理想的单分散微球. 考察了DBP和单体用量、各单体配比及染料对微球的形貌和单分散性的影响.     

A hyper-cross-linked polystyrene with nano-pore structure

Chloromethylated polystyrene (CMPS) beads were prepared by suspension polymerization of vinylbenzyl chloride (VBC), divinylbenzene (DVB) and styrene (St) in the presence of porogen. The same feed volume ratio of DVB leads to similar cross-linking degree for all CMPS, but decreasing VBC content provided a progressively reduced content of chloromethyl groups in each CMPS. Hyper-cross-linked polystyrene (HCLPS) beads were obtained by post cross-linking reaction of CMPS in dichloroethane (DCE) containing Friedel-Crafts catalyst. The role of porogen and its influence on nano-pore structure of HCLPS were investigated. The results showed that different types of porogen had significant effect on the nano-pore structure of the final products, such as specific surface area, average pore size and total pore volume. Using the mixture of toluene and cyclohexanol as inner porogen can yield the highest specific surface area for HCLPS beads. Moreover, higher amount of VBC lead to greater specific surface area and total pore volume. It was therefore indicated that nano-pore structure of HCLPS can be controllably prepared via changing porogen type and VBC concentration. Finally, the unprecedented swelling capacity was found for the hyper-cross-linked species derived from different porogen types.     

Effects of sorbitan monooleate on the interactions between cyclopentane hydrate particles and water droplets

The effects of a typical anti-agglomerant, sorbitan monooleate (Span80), on the interactions between cyclopentane (CyC5) hydrate particles and water droplets were investigated using a micromechanical force (MMF) apparatus. The concentration of Span80 in CyC5 was ranged from 0.01?wt% to 1?wt%, and the experimental temperature was set at 1.5°C and 7°C, respectively. The results indicate that the absorption of Span80 on the droplet surface can render the interfaces more stable, preventing hydrate agglomeration. When the preload/contact force exceeds the strength of the interface (相似文献   

Preparation and control of surface properties of monodisperse micrometer size beads by dispersion copolymerization of styrene and butyl methacrylate in polar media

The dispersion copolymerization of styrene and butyl methacrylate in ethanol-water medium to afford micrometer-size monodisperse beads has been investigated. Hydroxypropyl cel-lulose, poly (acrylic acid), and poly (vinylpyrrolidone) have been used as steric stabilizers, benzoyl peroxide and azobisisobutyronitrile as initiators. A novel steric stabilizing system consisting of a mixture of poly (acrylic acid) and hydroxypropyl cellulose has also been shown to lead to monodisperse beads for which the surface charge can be controlled by the relative ratio of steric stabilizers. The effect of several variables, such as the solvency of the medium, the concentration of co-monomers, the reaction temperature, and the type of steric stabilizer and initiator used on the bead size and size distribution are discussed. © 1995 John Wiley & Sons, Inc.     

Using hierarchical self-assembly to form three-dimensional lattices of spheres

This paper describes an approach to the fabrication of three-dimensional (3-D) structures of millimeter-scale spherical beads having a range of lattices-tetragonal, cubic, and hexagonal-using hierarchical self-assembly. The process has five steps: (i) metal-coated beads are packed in a rod-shaped cavity in an elastomeric polymer (poly(dimethylsiloxane), PDMS); (ii) the beads are embedded in a second polymer (PDMS or polyurethane, PU) using a procedure that leaves the parts of the beads in contact with the PDMS exposed; (iii) the exposed areas of the beads are coated with a solder having a low melting point; (iv) the polymer rods-with embedded beads and exposed solder drops-are suspended in an approximately isodense medium (an aqueous solution of KBr) and allowed to self-assemble by capillary interactions between the drops of molten solder; and (v) the assembly is finished by several procedures, including removing the beads from the polymer matrix by dissolution, filling the voids left with another material, and dissolving the matrix. The confinement of the beads in regular structures in polymer rods makes it possible to generate self-assembled structures with a variety of 3-D lattices; the type of the lattice formed can be controlled by varying the size of the beads, and the size and shape of the cross-section of the rods.     

Understanding the role of surfactants on the preparation of ZnS nanocrystals

We have synthesized surface modified ZnS nanoparticles of size 2-3 nm using non-ionic surfactant-stabilized reverse emulsions. The non-ionic surfactants in the Span series, i.e. sorbitan monolaurate (Span 20) and sorbitan monooleate (Span 80) of hydrophilic-lipophilic balance (HLB) values of 8.6 and 4.3, respectively, have been used for the stabilization of emulsions. The role of these surfactants in controlling the size and properties of the ZnS nanoparticles has been discussed. The triethylamine (TEA) has been proved to be the effective surface modifying (capping) agent for the preparation of free-standing ZnS nanoparticles. The Span 20 with the higher HLB value of 8.6 has been found to be highly suitable in synthesizing TEA-capped ZnS nanoparticles of smaller size and higher photophysical characteristics compared to that of the Span 80 of lower HLB value of 4.3. A mechanism for the formation of TEA-capped ZnS nanoparticles from the surfactant-stabilized reverse emulsions has been proposed.     

Incomplete phase inversion W/O/W emulsion and formation mechanism from an interfacial perspective

Water-in-oil-in-water (W/O/W) double emulsion can be prepared by incomplete phase inversion method using both medium chain triglycerides (MCT) and isopropyl myristate (IPM) as oil phase, Span 85-Tween 80 (HLB values of 2.5-3.0) as mixed emulsifiers. The preparation method was simple, and the final double emulsions were proved of good microstructure and particle size distribution. Owning to the addition of Tween 80 to Span 85, interfacial tension, interfacial viscosity and modulus decreased, which contributed to the phase inversion. Furthermore, formation of reverse micelles under high-speed dispersion may be a hypothesis to explain the incomplete phase inversion phenomenon.     

Monodisperse polymer beads as packing material for high-performance liquid chromatography. Preparation of macroporous poly(2,3-epoxypropyl vinylbenzyl ether-co-divinylbenzene) beads,their properties,and application to HPLC separations

In search for HPLC separation media with new surface chemistries, a styrene-based monomer, 2,3-epoxypropyl vinylbenzyl ether, containing reactive epoxide groups has been syn-thesized and copolymerized with divinylbenzene in a suspension polymerization. The process involves the use of size monodisperse particles that are swollen with monomer and then polymerized in the presence of a porogenic diluent consisting of a mixture of 4-methyl-2-pentanol and octane. The effect of concentration of divinylbenzene on the pore size dis-tribution and the specific surface area of the resulting uniformly sized porous poly(2,3-epoxypropyl vinylbenzyl ether-co-divinylbenzene) beads has been studied. The epoxide groups of the copolymer have been hydrolyzed and the beads used for reversed-phase chro-matography of both small molecules and proteins to show the effect of hydrophobicity of the matrix on the separation properties. Reversed-phase chromatography of alkylbenzenes follows the expected pattern while for proteins the hydrolyzed beads with the highest content of the crosslinking monomer exhibit a remarkable deviation from the predicted retention characteristics. © 1995 John Wiley & Sons, Inc.     

Preparation and functionalization of reactive monodisperse macroporous poly(chloromethylstyrene-co-styrene-co-divinylbenzene) beads by a staged templated suspension polymerization

Reactive monodisperse porous poly(chloromethylstyrene-co-styrene-co-divinylbenzene) beads have been prepared by a staged templated suspension polymerization method with different concentrations of linear polystyrene porogen and chloromethylstyrene in the polymerization mixture. The presence of a small amount of linear polystyrene in the polymerization mixture leads to a dramatic increase in both the pore size and the pore volume of the resulting beads. In contrast, addition of chloromethylstyrene leads to lower surface areas and smoother surfaces due to the reduced compatibility between the polystyrene porogen and the newly formed crosslinked chains. The modification of chloromethylstyrene beads by Gabriel synthesis to obtain aminated beads has also been studied. The final number of primary amino groups is related to the starting concentration of functional benzyl chloride moieties rather than to the porous properties. Both π-basic and π-acidic type chiral selectors, (R)-1-(1-naphthyl)-ethylamine and (R)-N-(3,5-dinitrobenzoyl)phenylglycine, respectively, have been attached to the amino functionalized beads, and the resulting chiral beads have been used in the model HPLC separations of enantiomers. © 1997 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 35: 2631–2643 1997