Specific Features of the Local Structure and Transport Properties of ZrO2–Sc2O3–Y2O3 and ZrO2–Sc2O3–Yb2O3 Crystals

Optics and Spectroscopy - The specific features of the local structure of ZrO2–Sc2O3–Y2O3 and ZrO2–Sc2O3–Yb2O3 crystals are revealed by optical spectroscopy using the Eu3+...     

Crystallization and conductivity of 2CaO–La2O3–5P2O5 glass–ceramic with Al2O3 addition

Al₂O₃ was added to a 2CaO–La₂O₃–5P₂O₅ metaphosphate, to replace 10% of the Ca²⁺ ions by Al³⁺, forming a phosphate with the nominal composition 1.8CaO–0.1Al₂O₃–La₂O₃–5P₂O₅. The effect of Al₂O₃ addition and heat treatment on the microstructure and conductivity of the resulting glass–ceramics was investigated by XRD, SEM, TEM, and AC impedance spectroscopy. Upon transformation from glass to glass–ceramic, conductivities increased significantly. The glasses were isochronally transformed at 700 and at 800 °C for 1 h or 5 h, in air, following heating at 3 or 10 °C/min. With Al₂O₃ addition, after a heat treatment at 700 °C, 100–300 nm nano-domains of LaP₃O₉ crystallized from the glass matrix. Annealing at 800 °C produced a further order of magnitude conductivity increase for the Al-free glass, but less so for the Al-containing glass.     

Structure,dielectric and bioactivity of P2O5–CaO–Na2O–B2O3 bioactive glass

Bioactive phosphate glasses have been widely investigated for bone repair. Phosphate glass system of 47P₂O₅–30.5CaO–(22.5?x)Na₂O–xB₂O₃ has been prepared by melt quenching technique. From the Raman analysis, it is confirmed that phosphate network form metaphosphate structure. Bioactivity of the glass is studied by immersing the prepared glass in simulated body fluid (SBF). All the glasses exhibited bioactivity after soaking in SBF. Addition of B₂O₃ to the glass by replacing the Na₂O produces considerable effect on the dielectric and bioactivity of the glass. Ion dynamics are also analyzed through imaginary modulus and imaginary dielectric permittivity.     

Synthesis and properties of MoO3–V2O5–PbO glasses

Lead vanadate glasses of the system xMoO₃–50V₂O₅–(50-x)PbO (0 ≤ x ≤ 25 mol. %) were synthesized and studied by FTIR and ultrasonic spectroscopy and differential scanning calorimetry to investigate the role of MoO₃ content on their atomic structure. The elastic properties and Debye temperatures of the glasses were investigated using sound velocity measurements at 4 MHz. The activation energy for the glass transition was derived from the dependence of the glass-transition temperature (T_g ) on the heating rate. Similarly, the activation energy of the crystallization process was also determined. According to the IR analysis, the vibrations of the vanadate structural units are shifted towards higher wavenumbers on the formation of bridging oxygens. The change of density and molar volume with MoO₃ content reveals that the molybdinate units are less dense than the lead oxide units. The observed compositional dependence of the elastic moduli is interpreted in terms of the effect of MoO₃ on the coordination number of the vanadate units. A good correlation was observed between the experimentally determined elastic moduli and those computed according to the Makishima–Mackenzie model. It is assumed that MoO₃ plays the role of a glass former by increasing the activation energy for the glass transition and the activation energy for crystallization and by increasing both the thermal stability and the glass formation range of the vanadate glasses.     

Electrical transport characteristics of ZnO–Bi2O3–B2O3 glasses

Optically clear glasses in the ZnO–Bi₂O₃–B₂O₃ (ZBBO) system were fabricated via the conventional melt-quenching technique. Dielectric constant and loss measurements carried out on ZBBO glasses unraveled nearly frequency (1 kHz–10 MHz)-independent dielectric characteristics associated with significantly low loss (D?=?0.004). However, weak temperature response was found with temperature coefficient of dielectric constant 18?±?4 ppm °C^?1 in the 35–250 °C temperature range. The conduction and relaxation phenomena were rationalized using universal AC conductivity power law and modulus formalism respectively. The activation energy for relaxation determined using imaginary parts of modulus peaks was 2.54 eV which was close to that of the DC conduction implying the involvement of similar energy barriers in both the processes. Stretched and power exponents were temperature dependent. The relaxation and conduction in these glasses were attributed to the hoping and migration of Bi³⁺ cations in their own and different local environment.     

Induced crystallization and the physical properties of PbO–Sb2O3–As2O3: MoO3 glass system

PbO–Sb₂O₃–As₂O₃ glasses mixed with different concentrations of MoO₃ (ranging from 0 to 1.0 mol%) were crystallized. The samples were characterized by X-ray diffraction, scanning electron microscopy and differential thermal analysis techniques. The X-ray diffraction and the scanning electron microscopic studies have revealed the presence of Pb₅Sb₂O₈, PbSb₂O₆, SbAsO₄, Sb₂MoO₆, Sb₄Mo₁₀O₃₁, As₄Mo₃O₁₅, Pb₅Sb₄O₁₁ crystalline phases in these samples. The differential thermal analysis indicated that the surface crystallization prevails over the bulk crystallization as the concentration of the crystallizing agent is increased. The infrared (IR) spectral studies exhibit bands due to MoO₄ structural units in addition to the conventional bands due to various antimonate and arsenate structural groups. The studies on PbO–Sb₂O₃–As₂O₃: MoO₃ glass-ceramics with respect to various physical properties viz., dielectric properties over a range of frequency and temperature, optical absorption, electron spin resonance (ESR) and magnetic susceptibility at room temperature have also been reported. The optical absorption, ESR and magnetic susceptibility studies indicated that the molybdenum ions exist in Mo⁵⁺ state in addition to Mo⁶⁺ state in these samples. The redox ratio found to increase as the concentration of the MoO₃ is increased. The variations observed in all these properties with the concentration of the crystallizing agent have been analyzed in the light of different oxidation states and environment of molybdenum ions in the glass ceramic network.     

Ultrasonic and FT-IR studies on Bi2O3–Er2O3–PbO glasses

Glasses in the 90Bi₂O₃–(10?x)Er₂O₃?xPbO (x = 3, 5, 7, 9 and 10 mol%) system have been prepared by the melt-quenching technique. Elastic properties and FT-IR spectroscopic studies have been employed to study the role of PbO in the structure of the investigated system. Elastic properties and Debye temperature were recorded using sound wave velocity measurements at 4 MHz at room temperature. The results showed that density increased and molar volume decreased, while both sound velocities increased with an increase in x. Infrared spectra of the glasses revealed that the bismuthate network is affected by an increase in PbO content. The results are interpreted in terms of the conversion of [BiO₆] into [BiO₃] structural units, indicating that Pb ions have been substituted for erbium ions as tetrahedral network formers. The elastic moduli increased with increasing PbO content due to the increased average bond strength and degree of connectivity, as a direct effect of the increase in [BiO₃] structural units.     

Characterization and tribological investigation of SiO2 and La2O3 sol–gel films

Thin films of SiO₂ and La₂O₃ were prepared on a glass substrate by a dip-coating process from specially formulated sols. The tribological properties of the resulting thin films sliding against a Si₃N₄ ball were evaluated on a one-way reciprocating friction and wear tester. The morphologies of the unworn and worn surfaces of the films were examined by an atomic force microscope (AFM) and a scanning electron microscope (SEM). La₂O₃ shows the best tribological performance. The coefficient of friction is about 0.1 and the wear life is over 5000 sliding passes both under higher (3 N) and lower load (1 N). The SiO₂ film derived from a specially formulated aqueous solution shows much better performance in resisting wear and reducing friction than the one derived from an ethanol solution. The wear mechanisms of the films are discussed based on SEM observation of the worn surface morphologies. SEM observation of the morphologies of worn surfaces indicates that the worn surface of La₂O₃ is too slight to be observed by SEM. The wear of SiO₂ derived from TEOS solution is the characteristic of delaminating, which is responsible for the abrupt failure of the film. The wear of SiO₂ derived from aqueous solution is the characteristic of fracture. Brittle fracture and severe abrasion dominate the wear of glass substrate.     

Influence of different Fe2O3 content on crystallization of MgO–Al2O3–SiO2–TiO2 system glass-ceramics

The crystallization behaviors of MgO–Al₂O₃–SiO₂–TiO₂ system glasses doping with different content Fe₂O₃ were investigated by means of differential thermal analysis and X-ray diffraction. The kinetic parameter of activation energy for crystallization (E) was obtained by the Owaza Johnson–Mehl–Avrami method. The results show that during the heat treatment, the intermediate phase of µ-cordierite initially precipitated from the glass matrix, and with the increasing temperature, it transformed to α-cordierite. The more the Fe₂O₃ content, the lower the crystallization peak temperature (T _p).But the lowering of T _p value did not mean that the value of E decreases correspondingly. The experimental results suggest that only with appropriate content (about 4.2 wt%), Fe₂O₃ can promote the crystallization of this glass effectively.     

Spectroscopic Properties of Er3+/Yb3+-codoped PbO–Bi2O3–Ga2O3–GeO2 Glasses

We investigate the spectroscopic properties of the 1.5-μm emission from the ⁴I_13/2 → ⁴I_15/2 transition of Er³⁺ ions in PbO–Bi₂O₃–Ga₂O₃–GeO₂ glasses for applications in broadband fiber amplifiers. The measured emission peak locates at 1,532 nm with a full width at half-maximum of ∼45 nm. The glasses exhibit a large stimulated emission cross-section of 0.89 × 10⁻²⁰ cm² and a large product of 40.0. Infrared-to-green upconversion occurs simultaneously upon excitation of the 1.5-μm emission with a commercially available 980 nm laser diode. The green-upconversion intensity has a quadratic dependence on incident pump laser power, indicating a two-photon process. Energy transfer processes and nonradiative phonon-assisted decays could account for the population of the ²H_11/2 of Er³⁺. The results indicate the possibility towards the development of lead–bismuth–gallate–germanate based glasses as photonics devices.     

Heat Transfer and Hydrodynamic Performance Analysis of a Miniature Tangential Heat Sink Using Al2O3–H2O and TiO2–H2O Nanofluids

In this article, thermal and hydrodynamic performances of a miniature tangential heat sink are investigated experimentally by using Al₂O₃–H₂O and TiO₂–H₂O nanofluids. The effects of flow rate and volume concentration on the thermal performance have been investigated for the Reynolds number range of 210 to 1,100. Experimental results show that the average convective heat transfer coefficient increases 14 and 11% and the bottom temperature of the heat sink decreases 2.2°C and 1.6°C by using Al₂O₃–H₂O and TiO₂–H₂O nanofluid instead of pure distilled water, respectively.     

Optical and IR study of Li2O–CuO–P2O5 glasses

Infrared (IR) and UV spectra of ternary Li₂O–CuO–P₂O₅ glasses in two series Li₂O(65−X)%–CuO(X%)–P₂O₅(35%), X = 20, 30, 40 and Li₂O(55−X)%–CuO(X%)–P₂O₅(45%), X = (10, 20, 30) were studied. Infrared (IR) investigations showed the metaphosphate and pyrophosphate structures and with increase of CuO content in metaphosphate glass, the skeleton of metaphosphate chains is gradually broken into short phosphate groups such as pyrophosphate. IR spectra showed one band at about 1,220 and 1,260 cm⁻¹ for P₂O₅(35%) and P₂O₅(45%) series, respectively, assigned to P=O bonds. For CuO additions ≤20 mol%, the glasses exhibit two bands in the frequency range 780–720 cm⁻¹ which are attributed to the presence of two P–O–P bridges in metaphosphate chain. But for CuO addition ≥30 mol%, the glasses exhibit only a single band at 760 cm⁻¹ which is assigned to the P–O–P linkage in pyrophosphate group. In optical investigations, absorption coefficient versus photon energy showed three regions: low energy side, Urbach absorption, and high energy side. In Urbach’s region, absorption coefficient depends exponentially on the photon energy. At high energy region, optical gap was calculated and investigations showed indirect transition in compounds and decreases in optical gap with increases of copper oxides contents that is because of electronic transitions and increasing of nonbridging oxygen content.     

Spectral dispersion of linear optical properties for Sm2O3 doped B2O3–PbO–Al2O3 glasses

Glasses having composition (B₂O₃)₂₅ (PbO)₇₀ (Al₂O₃)₅ (Sm₂O₃)_x ,where x=0, 0.5, 1, 2, 3 and 5 g were prepared using the normal melt quench technique. Spectral reflectance and transmittance at normal incidence of the glass samples are recorded with a spectrophotometer in the spectral range 220–2200 nm. These measured values are introduced into analytical expressions to calculate the real and imaginary parts of the refractive indices. Wemple–DiDomenico single oscillator model and one-term Sellmeier dispersion relations are used to model the real refractive indices. Dispersion parameters such as: single oscillator energy, dispersion energy, lattice oscillating strength, average oscillator wavelength, average oscillator strength and Abbe's number are deduced and compared. Absorption dispersion parameters such as: Fermi energy, optical energy gap for direct and indirect transitions, Urbach energy and steepness parameter are calculated. Effects of doping Sm₂O₃ on these linear optical parameters are investigated and interpreted.     

Broadband 1.5-μm emission of high erbium-doped Bi2O3–B2O3–Ga2O3 glasses

High Erbium-doped glass showing the wider 1.5-μm emission band is reported in the Bi₂O₃–B₂O₃–Ga₂O₃ system and its thermal stability and optical properties such as absorption, emission spectra, absorption and stimulated emission cross-sections and fluorescence lifetime are investigated. Compared with other glass hosts, the gain bandwidth properties of high Er³⁺ content in BBG glass are better than those of tellurite, germanate, silicate and phosphate glasses. The broad and flat ⁴I_13/2→⁴I_15/2 emission and the larger stimulated emission cross-section of Er³⁺ ions around 1.5 μm enable it to be used as a host material for potential broadband optical amplifiers at C and L bands in the microchip configuration.     

EPR and Magnetic Susceptibility of Na2O–CuO–P2O5 Glasses

Abstract

(50?x/2)Na₂O–xCuO–(50?x/2)P₂O₅ glasses (x=1, 5, 15, or 30 mol%) have been prepared and characterized by electron paramagnetic resonance (EPR) and magnetic susceptibility measurements. The shape of the Cu²⁺ EPR spectrum depends on the Cu content, and the corresponding computer simulations suggest that the Cu²⁺ ions occupy two different sites in these glasses: one of them is preponderant at low Cu content and the other is preponderant at high content, in which the Cu²⁺–Cu²⁺ interactions are more important. From EPR parameters, it was found that for the site at low content, the covalency of copper ion bonding with the surrounding ligands is appreciable. The magnetic susceptibility data appear to follow the Curie–Weiss law (χ=C/(T?θ_p)) with negative paramagnetic Curie temperature θ_p indicating antiferromagnetic interactions between Cu²⁺ ions that are more significant in the samples with high Cu content, in agreement with EPR results.     

Study of electrical conductivity and phase transition in Bi2O3–V2O5 system

The solid solutions of bismuth–vanadate were prepared by the conventional solid-state reaction. The sample characterization and the study of phase transition were done by using FT-IR, X-ray diffraction (XRD) and DSC measurements. AC impedance measurements proved that the oxide ion conductivity predominantly arises from the grain and grain boundary contributions as two well-defined semicircles are clearly seen along with an inclined spike. The electrical conductivity of Bi₂O₃–V₂O₅ has been studied at different temperatures for various molar ratios. The isothermal conductivity increases with an increase in the concentration of V₂O₅ due to the vacancy migration phenomenon. It has been found that the conductivity of different compositions of Bi₂O₃–V₂O₅ increases and shows a jump in the temperature range 230–260°C due to the phase transition of BiVO₄ from monoclinic scheelite type to that of tetragonal scheelite type. The endothermic peak in DSC at around 260°C reveals the phase transition, which is also confirmed by the XRD and FT-IR analysis. The XRD patterns confirmed the monoclinic structure of BiVO₄.     

Optical,thermal, and structural properties of Nb2O5–TeO2 and WO3–TeO2 glasses

Glass samples from two systems, Nb₂O₅–TeO₂ and WO₃–TeO₂, were prepared at two melt quenching rates and characterized by density, DSC, UV-visible, and Raman spectroscopy. Addition of Nb₂O₅ decreased the density while increase in the WO₃ concentration increased the density. Glasses prepared at higher quenching rates had smaller densities than glasses of the same composition prepared at lower quenching rate although the short-range structure of both glasses were identical, as revealed by Raman spectroscopy. Optical studies found an intense absorption band just below the absorption edge in both the glass series. This band was attributed to electronic transitions of Nb⁵⁺ and W⁶⁺ ions and a lone pair of electrons on Te atoms. Glass transition temperature increased with increase in Nb₂O₅ and WO₃ mol% due to the increase in average bond strength in the glass network. Raman spectroscopy showed that the concentration of TeO₄ units decreased with the increase in Nb₂O₅ and WO₃ concentrations.