Na1−xLixNbO3 ceramics studied by X-ray diffraction, dielectric, pyroelectric, piezoelectric and Raman spectroscopy

Na_1−xLi_xNbO₃ ceramics with composition 0.05≤x≤0.30 were prepared by solid-state reaction method and sintered in the temperature range 1100-1150 °C. These ceramics were characterised by X-ray diffraction as well as dielectric permittivity measurements and Raman spectroscopy. Dielectric properties of ceramics belonging to the whole composition domain were investigated in a broad range of temperatures from 300 to 750 K and frequencies from 0.1 to 200 kHz. The Rietveld refinement powder X-ray diffraction analysis showed that these ceramics have a single phase of perovskite structure with orthorhombic symmetry for x≤0.15 and two phases coexistence of rhombohedral and orthorhombic above x=0.20. The evolution of the permittivity as a function of temperature and frequency showed that these ceramics Na_1−xLi_xNbO₃ with composition 0.05≤x≤0.15 present the classical ferroelectric character and the phase transition temperature T_C increases as x content increases. The polarisation state was checked by pyroelectric and piezoelectric measurements. For x=0.05, the piezoelectric coefficient d₃₁ is of 2pC/N. The evolution of the Raman spectra was studied as a function of temperatures and compositions. The results of the Raman spectroscopy study confirm our dielectric measurements, and they indicate clearly the transition from the polar ferroelectric phase to the non-polar paraelectric one.     

Dependence of high electric-field-induced strain on the composition and orientation of Pb(Mg1/3Nb2/3)O3-PbTiO3 crystals

Electric-field-induced strain behavior of (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMNT) crystals with different orientations and compositions was investigated for use as electromechanical actuators. Crystallographically, high strains with low hysteresis were achieved for 〈001〉 oriented rhombohedral crystals (29%≤x≤31%) near a morphotropic phase boundary, rather than 〈110〉 and 〈111〉. Domain instability could explain inferior strain levels and large hysteresis for 〈110〉 and 〈111〉 oriented crystals. Ultrahigh strain levels up to 1.8% could be achieved for 〈001〉 oriented PMNT crystals, being related to an E-field induced phase transition. −2 kV/cm negative E-field can be applied to PMNT ferroelectric material with low hysteresis. High strain with low hysteresis makes PMNT crystals promising candidates for high performance solid-state actuators.     

Effects of composition on phase structure and electrical properties of (K0.5Na0.5)0.90Li0.06Sr0.02Nb(1−x)SbxO3 ceramics

Lead-free (K_0.5Na_0.5)_0.90Li_0.06Sr_0.02Nb_(1−x)Sb_xO₃ (KNLSN-Sb_x) ceramics were synthesized by ordinary sintering technique. The compositional dependence of phase structure and electrical properties of the ceramics was systematically investigated. All samples possessed pure perovskite structure, showing room temperature symmetries of orthorhombic at x<0.01, coexistence of orthorhombic and tetragonal phases at x=0.01, and tetragonal at 0.02≤x≤0.05. The temperature of the polymorphic phase transition (PPT) was shifted to lower temperature and dielectric relaxor behavior was induced by increasing Sb content. The samples near the coexistence region (x=0.01) exhibited enhanced electrical properties: d₃₃∼145 pC/N, k_p∼38% and P_r∼20.4 μC/cm².     

Structural distortion and phase transition studies of Aurivillius type Sr1−xPbxBi2Nb2O9 ferroelectric ceramics

In this paper, effects of lead doping on the lattice response and phase transitions of Sr_1−xPb_xBi₂Nb₂O₉ (x=0.0-0.5 in steps of 0.1) ferroelectric ceramics are reported. It is observed that structure attains more tetragonality with doping of lead up to 40%. Increased orthorhombic distortion is observed for undoped SBN and 50 at.% lead substituted SBN. Phase transitions for all samples were studied using Curie temperature measurements and are explained in terms of lattice response of these ceramics. Sample with x=0.5 shows decreased tetragonal strain and Curie temperature. Relationship of polarization with lattice response is discussed.     

Large pyroelectric response in (Pb0.87La0.02Ba0.1)(Zr0.7Sn0.3−x Ti x )O3 antiferroelectric ceramics under DC bias field

(Pb_0.87La_0.02Ba_0.1)(Zr_0.7Sn_0.3−x Ti _x )O₃ (PLBZST, 0.06≤x≤0.09) antiferroelectric ceramics were fabricated by conventional solid state reaction process, and their ferroelectric, dielectric, and pyroelectric properties were systemically investigated. PLBZST with different Ti content were all confirmed to be in an antiferroelectric phase at T=50°C, which is close to the lowest phase transition temperature. Compared with conventional FE ceramics, PLBZST antiferroelectric ceramics exhibited higher electric field induced pyroelectric coefficient (p). As the content of Ti increased from 0.06 to 0.09, the pyroelectric coefficient increased from 1000 to 6500 μC/m²K under a 500 V/mm DC bias field. The maximum pyroelectric coefficient of 8400 μC/m²K was obtained at x=0.09 when an 850 V/mm DC bias field was applied, which is far larger than that of conventional phase transition pyroelectric materials. Large pyroelectric response is beneficial for the development of infrared detectors and thermal imaging sensors.     

Dielectric and pyroelectric activities in Pb(Zr1−xTix)O3 ceramics: The role of the phase transition effects

Pure and Nb-doped Pb(Zr_1−xTi_x)O₃ (x = 0.47, 0.48, 0.50) ceramics were prepared by conventional solid-state reaction technique. Dielectric anomalies are observed in both kinds of samples near room temperature. The anomalies could be depressed by donor doping and prefer to be significant in ceramics with tetragonal crystallographic phase. Phase transition mechanism and domain wall pinning effect are proposed to explain this anomaly, and the former is considered as the dominated reason. Further results of the pyroelectric measurements confirm the existence of the ferroelectric–ferroelectric phase transition.     

Magnetic study of phase separation and charge ordering in La1−xSrxMnO3 near x=0.5

We have investigated the magnetic phase diagram of polycrystalline and single-crystal La_1−xSr_xMnO₃ near 0.46≤x≤0.50. It turns out that for x<0.48, the polycrystalline material is ferromagnetic (FM), but for x≥0.48, incipient charge ordering takes place along with antiferromagnetism. At x=0.48, the ferromagnetic-antiferromagnetic phase transition in ceramics occurs at less than 85 kOe but requires significantly larger field for increasing x. These observations are in contrast to what is found in the single crystals, which are all FM.     

Investigations of structural, dielectric and ferroelectric behavior of europium substituted SrBi2Ta2O9 ferroelectric ceramics

Europium substituted samples of the compositions Sr_1−xEu_xBi₂Ta₂O₉ (x=0.0,0.025,0.050,0.10 and 0.20) were synthesized by solid state reaction method and studied for their structural, dielectric and ferroelectric properties. The X-ray diffractograms confirmed the formation of single phase layered perovskite structure in all the samples. The temperature variation of dielectric constant shows that the Curie temperature (T_c) decreases on increasing concentration of europium. The dielectric loss reduces significantly with europium addition. The P-E studies of the Eu-substituted SBT ceramics show that the remanent polarization increases with increasing concentration of europium.     

Structural and magnetic phase diagram and room temperature CMR effect of La1−xAgxMnO3

The study of the structural and magnetic phase diagram of the manganites La_1−xAg_xMnO₃ shows similarity with the La_1−x′Sr_x′MnO₃ series, involving a metallic ferromagnetic domain at relatively high temperature (≈300 K). The Ag-system differs from the Sr-one by a much smaller homogeneity range (x≤1/6) and the absence of charge ordering. But the most important feature of the Ag-manganites deals with the exceptionally high magnetoresistance (−25%) at room temperature under 1.2 T, that appears for the composition x=1/6. The latter is interpreted as the coincidence of the optimal double exchange condition (Mn³⁺:Mn⁴⁺=2) with T_max=300 K (maximum of the ρ(T) curve in zero field).     

Effect of electric field on electrocaloric effect in Pb(Zr1 − xTix)O3 solid solution

A thermodynamic analysis is employed to investigate the intrinsic electrocaloric effect of Pb(Zr_1 − xTi_x)O₃ solid solution system under the different electric field. Theoretical analysis indicates that Pb(Zr_1 − xTi_x)O₃ system has the giant electrocaloric coefficient and the large adiabatic temperature change near its ferroelectric Curie temperature. The applied electric field decreases not only the electrocaloric coefficient but also its temperature dependence. Furthermore, it increases the adiabatic temperature change as well as its dependence of temperature. The temperature corresponding to the maximum of electrocaloric coefficient and adiabatic temperature change increases with the enhancement of electric field because of its first-order phase transition between ferroelectric phase and paraelectric phase.     

Structural and dielectric properties in the (Ba1−xCax)(Ti0.95Zr0.05)O3 ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.95Zr_0.05)O₃ (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 ≤ x ≤ 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x ≥ 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T_c.     

The pressure influence on the incommensurate-commensurate ferroelectric phase transition in [4-NH2C5H4NH][SbCl4]

The dielectric properties of the [4-NH₂C₅H₄NH] SbCl₄ (abbreviated as 4-APCA) crystal were investigated under hydrostatic pressure up to 300 Mpa. The pressure-temperature phase diagram was given. The paraelectric-ferroelectric phase transition (II→III) temperature (T_c) increases linearly with increasing pressure with a slope dT_c/dp=21×10⁻² K/MPa. The pressure dependence of Curie-Weiss constants has been evaluated also. In the paraelectric phase (II) the Curie constant (C₊) was pressure dependent whereas the C₋ constant over the ferroelectric phase (III) was almost constant. The results are interpreted in terms of improper and displacive type phase transition model with a soft phonon at a zone boundary.     

Hyperfine characterization of Bi1.9Te0.1SrNb1.9Hf0.1O9

The Aurivillius type oxide Bi_1.9Te_0.1SrNb_1.9Hf_0.1O₉ has been studied by Perturbed Angular Correlations spectroscopy using ¹⁸¹Ta probes. The spin precession curves were measured from room temperature up to 873 K. Two sites are occupied by probes and the temperature dependence of both indicates a continuous phase transition at about 625 K. One site is ordered while the other is disordered. This situation is analyzed in terms of simple models already applied to perovskites. The transition temperature of the solid solution Bi_2−xTe_xSrNb_2−xHf_xO₉ (with 0≤x≤0.5) shows a strong dependence on composition.     

Structural relaxation and rigidity transition in aged and rejuvenated AsxSe100−x glasses

Differential scanning calorimetry (DSC) measurements were performed to investigate the kinetics of the structural relaxation in aged and unaged (rejuvenated) As_xSe_100−x glasses with 0≤x≤40. The activation energy of the glass transition (E_a) of the aged and rejuvenated glasses was determined from the variation of the glass transition temperature (T_g) with the heating rates (β). Significant effect of prolonged aging of the glasses on the values E_a was observed. Evidence of transition from floppy to rigid phase is presented. The observed significant physical aging in samples with composition x<40 indicates the absence of the intermediate phase. The compositional dependence of T_g for aged and rejuvenated data was analyzed using the stochastic agglomeration theory.     

Study of relaxor-like behaviour of laser ablated (Pb, La)Tio3 thin films

Lanthanum modified lead titanate (PLT) thin films are one of the potential candidates for the pyroelectric and memory applications due to their excellent dielectric, pyroelectric and ferroelectric properties. PLT thin films with 25 at.% of La were deposited on platinum coated Si substrates by the laser ablation technique. The phase transition studies were done in the temperature range of −40 to 150 °C as a function of frequency and ac field. A diffused phase transition with the shifting of the maximum dielectric permittivity (?_max) to higher temperatures with the increase of frequency and dielectric dispersion with frequency at the lower temperatures were observed. The variation of the temperature corresponding to maximum dielectric constant T_m, with frequency follows the Vogel-Fulcher relation, which is the characteristic of the relaxor-like behavior of the material. With the increase of ac drive, the T_max was shifted to lower value.     

Phase transformation behavior and dielectric characteristics of BaTi1−x(Al1/2Nb1/2)xO3 (0.01≤x≤0.40) ceramics

Microstructure, phase transformation behavior and dielectric properties of BaTi_1−x(Al_1/2Nb_1/2)_xO₃ (0.01≤x≤0.40) ceramics were investigated. A high level of (Al_1/2Nb_1/2)⁴⁺ substitution for Ti⁴⁺ ions was not conducive to the stability of the perovskite structure and resulted in the formation of BaAl₂O₄. As x was increased, lattice constants and unit cell volume decreased, reached a minimum at x=0.10 and then increased. The BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics at room temperature experienced a transformation from ferroelectric to paraelectric phase with increasing (Al_1/2Nb_1/2)⁴⁺ concentration. Meanwhile, permittivity of the BaTi_1−x(Al_1/2Nb_1/2)_xO₃ ceramics was markedly reduced, while Q value was slightly increased. Frequency dispersion of dielectric peak was obviously increased as x was increased from 0.01 to 0.10. It is of great interest that a dielectric abnormity represented by a broad dielectric peak at 200-400 K was observed for the composition with x=0.40.     

Carbon doping in MgB2: role of boron and carbon px(y) bands

We have studied the changes in the electronic structure and the superconducting transition temperature T_c of Mg(B_1−xC_x)₂ alloys as a function of x with 0≤x≤0.3. Our density-functional-based approach uses the coherent-potential approximation to describe the effects of disorder, the Gaspari-Gyorffy formalism to estimate the electron-phonon matrix elements and the Allen-Dynes equation to calculate T_c in these alloys. We find that the changes in the electronic structure of Mg(B_1−xC_x)₂ alloys, especially near the Fermi energy E_F, come mainly from the outward movement of E_F with increasing x, and the effects of disorder in the B plane are small. In particular, our results show a sharp decline in both B and C p_x(y) states for 0.2≤x≤0.3. Our calculated variation in T_c of Mg(B_1−xC_x)₂ alloys is in qualitative agreement with the experiments.     

The suppression of structural phase transformation in LaVO3 and La1−xSrxVO3 thin films fabricated by pulsed laser deposition

Highly oriented (100) thin films of LaVO₃ and La_1−xSr_xVO₃ have been fabricated by pulsed laser deposition in a reducing atmosphere. The films show a transition from insulating to metallic behaviour in the composition region of x, 0.175<x<0.200. In the single crystals of the antiferromagnetic insulating phase, a first-order structural phase transition is observed few degrees below the magnetic transition, which manifests itself as a kink in the temperature dependence of resistivity. In the highly oriented thin films of LaVO₃ and La_1−xSr_xVO₃ fabricated on lattice matched substrates in this study, the structural phase transformation in the insulating phase has been suppressed. The electrical conduction is found to take place via hopping through localized states at low temperatures. The metallic compositions show a non-linear (T^1.5) behaviour in the temperature dependence of resistivity. V (2p) core level spectra of these films show a gradual change in the relative intensities of V³⁺ and V⁴⁺ ions as the value of x increases.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.     

Effect of composition and thermal annealing on the absorption and electrical conduction of Se85−xTe15Sbx glasses

The optical absorption of the as-prepared and thermally annealed Se_85−xTe₁₅Sb_x (0≤x≤9) thin films was measured. The mechanism of the optical absorption follows the rule of non-direct transition. The optical energy gap (E₀) decreased from 1.12 to 0.84 eV with increasing Sb content of the as-prepared films from 0 to 9 at.%. The as-prepared Se₇₆Te₁₅Sb₉ films showed an increase in (E₀) with increasing the temperature of annealing in the range above T_g (363 K). The electrical conductivity of the as-prepared and annealed films was found to be of Arrhenius type with temperature in the range 300-360 K. The activation energy for conduction was found to decrease with increasing both the Sb content and temperature of annealing. The results were discussed on the basis of the lone-pair electron effect and of amorphous crystalline transformation.