Thermooxidation rate of diacetate terminated polyoxymethylene with various morphological structures

Thermooxidative degradation of POM films with different morphological structures was investigated in air in the temperature range of 145–160C.The various degrees of crystallinity and different morphologies of POM films were obtained by quenching molten samples to different temperatures. The studies of thermooxidation by IR absorption and weight loss measurements have shown that the process is influenced by sample morphology. The induction period and the advanced states of, chain scission depend on oxygen diffusion into the samples. This process is strongly dependent upon the degree of crystallinity and morphological structure of the polymer.     

The rheological and crystallization behavior of polyoxymethylene

In the polymer melt processing, the solidification has a huge importance on the properties of the resulting part. For a semi-crystalline resin, this phenomenon involves a complex interplay between crystallization and the material rheology. In this work, an investigation is carried out on the influence of thermal conditions on crystallization kinetics and rheology of two commercial polyoxymethylene (POM) copolymers. In particular, isothermal crystallization experiments using differential scanning calorimetry (DSC) and rotational rheometry to measure the dynamic viscosity are performed. The evolution of the relative crystallinity and Normalized Rheological Function (NRF) are correlated by a recent technique which allows simultaneous analysis of several measurements, even if they are not carried out at same temperatures. On this basis, a relationship between the crystallinity and the hardening, i.e. the sharp increase in the viscosity, is obtained.     

Effects of physical aging,crystallinity, and orientation on the enzymatic degradation of poly(lactic acid)

The effects of physical aging, degree of crystallinity, and orientation of poly(lactic acid) (PLA) were studied using differential scanning calorimetry (DSC) and wide angle X-ray scattering (WAXS). The samples of PLA with 96% [L] and 4% [D] contents were prepared by injection molding. The physical aging of PLA strongly depended on time and temperature. The change of rate of physical aging was very fast initially and slowed down as time increased. The enzymatic degradation of PLA was carried out with proteinase K at 37°C at a pH value of 8.6 in a Tris/HCl buffer solution. The enzymatic degradation rate was found to decrease as a function of physical aging (i.e., excess enthalpy relaxation). The rate of enzymatic degradation of PLA decreased with the increase in crystallinity. A threshold was observed when the heat of fusion was less than 20 J/g. The weight loss of PLA with a low level of crystallinity had no apparent change during any period of testing time. The rates of enzymatic degradation of stretched and injection-molded specimens were comparable. © 1996 John Wiley & Sons, Inc.     

Direct ultrasonic agitation for rapid extraction of organic matter from airborne particulate

Direct ultrasonic extraction (DUE) is proposed as simple and rapid sample pretreatment method. This new approach is applied to the extraction of particulate organic matter (POM) from airborne particulate by using dichloromethane (DCM) or DCM/methanol (90/10, v/v) as extractant. The analytical determination was carried out by weighing the extractable POM on an electrobalance. Total recovery for POM could be obtained when the sample was extracted three times with 25–50 mL extractant each for about 5 min at 50 W ultrasonic power. In comparison with conventional Soxhlet extraction, less extraction time (total 15 min only) and solvent consumption(100 mL) were required by DUE. The efficiency of the DUE was similar or even higher than the routine Soxhlet method. Additionally, the new extractor is very simple and easy to use and can accelerate the extraction procedures of organic components from various solid samples.     

Direct ultrasonic agitation for rapid extraction of organic matter from airborne particulate

Direct ultrasonic extraction (DUE) is proposed as simple and rapid sample pretreatment method. This new approach is applied to the extraction of particulate organic matter (POM) from airborne particulate by using dichloromethane (DCM) or DCM/methanol (90/10, v/v) as extractant. The analytical determination was carried out by weighing the extractable POM on an electrobalance. Total recovery for POM could be obtained when the sample was extracted three times with 25-50 mL extractant each for about 5 min at 50 W ultrasonic power. In comparison with conventional Soxhlet extraction, less extraction time (total 15 min only) and solvent consumption (100 mL) were required by DUE. The efficiency of the DUE was similar or even higher than the routine Soxhlet method. Additionally, the new extractor is very simple and easy to use and can accelerate the extraction procedures of organic components from various solid samples.     

Effects of ultrasonic treatment on unfilled butadiene rubber

The ultrasonic treatment of unfilled butadiene rubber (BR) gum with a grooved‐barrel ultrasonic reactor was carried out, leading to changes in the structure and physical properties. The ultrasonic treatment of BR gum led to gel formation, with the amount dependent on the amplitude. The rheological and mechanical properties of the ultrasonically treated samples and their vulcanizates were measured and compared with those of the virgin samples. Gel permeation chromatography measurements of the sol part of the virgin and the treated samples were carried out. Rheological property and molecular weight measurements indicated the creation of a branched structure and the occurrence of degradation in ultrasonically treated BR gum. Because of degradation, the tensile strength and Young's modulus of treated BR were lower than those of untreated BR, whereas the elongation at break was practically intact. Differential scanning calorimetry (DSC) curves at a high‐temperature range showed exothermic peaks with enthalpy reduction in the treated BR, indicating a decrease in the number of double bonds due to gel formation. DSC curves at a low‐temperature range indicated increased crystallinity in the treated samples. Competing reactions of gel formation, branching, and degradation occurred during the ultrasonic treatment. © 2003 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 41: 2959–2968, 2003     

Effect of ionomers on mechanical properties, morphology, and rheology of polyoxymethylene and its blends with methyl methacrylate-styrene-butadiene copolymer

Two ionomers, ethylene-methacrylic acid copolymer ionized with sodium cation (EMA-Na) and zinc cation (EMA-Zn), were employed as impact modifiers to prepare blends with polyoxymethylene (POM) via a melt extrusion. A copolymer of methyl methacrylate-styrene-butadiene (MBS) used as a co-impact modifier was also incorporated into the blends. The mechanical properties, thermal properties, morphology, and rheology were studied. A moderate toughening was observed for POM/ionomer binary blends, which was attributable to the rubbery natural and good adhesion of the ionomers. EMA-Zn exhibited a much better toughening effect than EMA-Na because of its higher elasticity and stronger interaction with POM. The incorporation of the ionomers into POM/MBS blends resulted in an improvement of mechanical properties, which was attributable to the compatibilizing effect of ionomer on POM/MBS blending system. The observation of scanning electron microscopy demonstrated that the finer phase domains were caused by incorporation of ionomers, which, acting as a compatibilizer as well as an impact modifier, reduced the interfacial tension and improved the interfacial adhesion between the phases. Differential scanning calorimetry investigation indicated that the presence of ionomer in the blends disturbed the crystallization of POM and resulted in a decrease in the crystallinity of POM. The evaluation of melt flow index revealed an increase in viscosity of the blends by incorporation of the ionomers, which was caused the ionic interaction between POM and the ionomers.     

Control of thermal cross‐linking reactions and the degree of crystallinity of syndiotactic 1,2‐polybutadiene

Thermal stability, crystallization, morphological development, subsequently melting, and crystallinity control of a syndiotactic 1,2‐polybutadiene sample were carefully carried out by thermogravimetry (TGA), polarized optical microscopy (POM), differential scanning calorimetry (DSC), temperature‐modulated differential scanning calorimetry (TMDSC), and wide‐angle X‐ray diffraction (WAXD), respectively. The experiments indicate that thermal cross‐linking reaction rates under nitrogen protection and in air are different for this polymer at temperature above 155 °C. Under nitrogen protection, the thermal cross‐linking reaction rate is delayed and the mechanism of melt crystallization obtained from the DSC results is in good accordance with that from POM observation. TMDSC results indicate that melting–recrystallization–melting model is more proper to explain the double melting events of this sample. At the same time, the evolution of the degree of crystallinity as the function of the time was investigated by WAXD profiles for the samples firstly crystallized at 145 °C for 1 h and then kept at 163 °C mediated between the temperatures of the double peaks. It shows that as prolonging the annealing time at 163 °C thermal cross‐linking reactions possibly occur, leading to gradual reduction of the apparent crystallite sizes, evaluated by Scherrer equation and the degree of crystallinity. The changing sequence of the relative intensity of the stronger four diffraction peaks with time due to thermal cross‐linking reactions is (111)/(201) > (210) > (010) > (200)/(110). © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 2885–2897, 2005     

X-ray analysis of the influence of various nucleating agents on the crystallinity of poly-α-butene

The influence of various nucleating agents on the crystallinity of poly-α-butene form I has been studied. The nucleating agents were: adipic acid, salicylic acid, p-aminobenzoic acid, sodium benzoate and sorbic acid; their influences on the lattice parameters, degree of crystallinity, size of crystallites and texture have been examined. The analysis was carried out by wide-angle X-ray diffraction. The relative degrees of crystallinity in poly-α-butene samples containing nucleating agents were measured using the Hermans-Weidinger procedure; in order to obtain the size of crystallites, the Debye-Scherrer method was applied. The lattice parameters show no change but the relative degree of crystallinity, the size of crystallites and their texture depend on the nucleating agent used.     

Synergistic effect of thermoplastic phenolic resin and multiwalled carbon nanotubes on the crystallization of polyoxymethylene

To reduce the crystallization rate of polyoxymethylene (POM) to meet the requirement of thick-walled and large-sized articles production, and maintain high crystallinity as well as obtain refined crystalline grains to ensure the strength and stiffness simultaneously, thermoplastic phenolic resin (PF) and multiwalled carbon nanotubes (MWCNTs) were used as crystal growth inhibitor and nucleating agent, respectively, and their effects on the crystallization of POM were studied in details. The results showed that PF is an effective inhibitor and MWCNTs exhibits excellent nucleation effect on POM. Based on the obtained results, their synergistic influences on the crystallization process of POM were investigated. It is found that the objective of decreasing the crystallization rate while maintaining high crystallinity and forming fine crystalline grains can be realized. The 97/3/1 wt% POM/PF/MWCNTs, compared with those of neat POM, The T _c shifts by 3.3°C to a lower temperature, the crystallization enthalpy increases by 16.1 J/g and the full width at half-maximum widens by 48.5%. The modulation effect of PF and MWCNTs on the crystallization is closely related to the PF content and dispersion, the distribution and dispersion of MWCNTs in the PF and POM phases.     

The effect of morphology on thermal stability of isotactic polypropylene in air

Summary The studies on thermooxidative degradation of isotactic polypropylene films with different morphological structure were carried out in the air in temperature range 85–145 °C. The various crystallinity degrees and morphologies of PP films were obtained by cooling the melt and crystallization at different temperatures. The studies on structural changes going together with degradation and on the kinetics of chain scission have shown that this reaction occurs in two stages. The first is connected with consumption of oxygen dissolved in the initial films and the second is controlled by its diffusion into the films. The rates of degradation and structural changes occurring simultaneously depend not only on the initial crystallinity but also on morphology of the systems under study.With 8 figures and 1 tableDedicated to Prof. G. Rehage on occasion of his 60th birthday     

聚己内酯在聚己内酯/聚乙烯基甲基醚共混体系中的结晶研究

通过示差扫描量热(DSC)、广角X射线衍射(WAXD)、小角X射线散射(SAXS)研究了聚己内酯(PCL)/聚乙烯基甲基醚(PVME)共混体系中PCL的结晶行为.研究结果表明,共混聚合物中PCL的结晶度几乎不随体系的组成而发生变化.共混物中PVME的存在没有改变PCL的晶体结构,但是随着PVME含量的增加,片晶之间的距离则大,这主要是由于非晶层增厚引起的.     

高分子量聚对二氧环己酮体外降解研究

对高分子量(Mν=2.8×105)的聚对二氧环己酮条状样品在37℃磷酸缓冲溶液(PBS)中的降解行为进行了研究,通过定期观察其吸水率与质量损失,pH,特性黏数,降解过程中样品形态与晶体结构,热力学性能与机械性能的改化,发现此高分子量的聚对二氧环己酮在体外降解过程中质量损失与吸水率变化不大,但分子量下降明显,同时样品表面缺陷逐渐增加;结晶度与玻璃化温度随之改变,但其晶体结构基本保持不变;到第6周时,其力学强度基本消失.证明高分子量PPDO具有较慢的降解速度,显示出很好的稳定性.     

Transition metal ion-substituted polyoxometalates entrapped in polypyrrole as an electrochemical sensor for hydrogen peroxide

A conducting polymer was used for the immobilization of various transition metal ion-substituted Dawson-type polyoxometalates (POMs) onto glassy carbon electrodes. Voltammetric responses of films of different thicknesses were stable within the pH domain 2-7 and reveal redox processes associated with the conducting polymer, the entrapped POMs and incorporated metal ions. The resulting POM doped polypyrrole films were found to be extremely stable towards redox switching between the various redox states associated with the incorporated POM. An amperometric sensor for hydrogen peroxide detection based upon the POM doped polymer films was investigated. The detection limits were 0.3 and 0.6 μM, for the Cu(2+)- and Fe(3+)-substituted POM-doped polypyrrole films respectively, with a linear region from 0.1 up to 2 mM H(2)O(2). Surface characterization of the polymer films was carried out using atomic force microscopy, X-ray photoelectron spectroscopy and scanning electron microscopy.     

End-life Prediction of Commercial PLA Used for Food Packaging through Short Term TGA Experiments： Real Chance or Low Reliability？

A long-term(about nine months) isothermal degradation experiment of two different commercial polylactide(PLA) samples used for food packaging was carried out at a relatively low temperature(423 K). Thermooxidative degradations of the same polymers were carried out in a thermogravimetric(TG) analyser, at higher temperatures(453 K ≤ T ≤ 523 K), under isothermal heating conditions. The obtained set of experimental TG data was used to determine the apparent activation energy(Ea) of degradation through two isothermal kinetic methods. The results from long-term experiment evidenced considerable mass loss for both PLA samples in the investigated period, but the experimental data were not in agreement with those from the short-term degradations at higher temperatures, thus suggesting a different degradation kinetics, and, then a low reliability of the lifetime predictions for polymers in service or degradation forecasts for the end of their life based on experiments at higher temperatures.     

Properties of cellulose pulps from acidic and basic processes

Research has intensified in recent years on organic solvent pulping processes to supplement or replace conventional pulping processes. One of the main problems with organosolv pulps is the inferior tear strength compared to kraft pulps. An investigation of the properties of two acidic (acetic acid organosolv and acid sulfite) and one basic white spruce pulp (kraft) was carried out to determine factors affecting differences in tear strength. Properties evaluated were lignin and sugar content, mineral composition, ESCA oxygen-to-carbon ratios, acid-base characteristics, water wettabilities, degree of polymerization and crystallinity of cellulose, fiber length and coarseness, and physical properties of the various pulps. Differences in tear strength have been attributed to degradation and changes in the cellulose structure, the hemicellulose-lignin matrix in which the degree of polymerization of hemicelluloses plays the most important role in low yield pulps, and finally, the bonding capacity of the fiber surfaces.     

Design of modified plastic surfaces for antimicrobial applications: Impact of ionizing radiation on the physical and mechanical properties of polypropylene

Surface modification of polypropylene (PP) sheets was carried out by radiation induced graft polymerization of hydrophilic functional molecules such as N,N-dimethylacrylamide (DMA) and [2-methacryloyloxy)ethyl] trimethylammonium chloride, which is a quaternary ammonium salt (QAS).Polypropylene sheets were activated prior to the grafting reaction by using electron beam radiation. The changes in morphology, crystallinity and tensile parameters like deformation and stress at yield and deformation at break of PP after irradiation were investigated. The results showed that a minor crystalline reorganization takes place during the irradiation of PP at 100 kGy.The grafting has been observed to be strongly dependent on the monomer dilution in the reaction medium. After grafting of QAS (40%) and DMA (20%) it was possible to develop highly hydrophilic surfaces (water contact angle comprised between 30 and 41°). The surfaces of virgin, irradiated and grafted PP were studied using polarized optical microscopy (POM) and scanning electron microscopy (SEM). Spherical particles (i.e. polystyrene or silica beads) adhering to the modified samples were studied according to the surface parameters. Adhesion tests confirmed the strong influence of substrate type (mainly hydrophilicity and roughness) and to a lesser extent underlined the role of electrostatic interactions for the design of plastic surfaces for antimicrobial applications.     

Crystalline properties and decomposition kinetics of cellulose fibers in wood pulp obtained by two pulping processes

In this study two cellulose fibers, Eucalyptus grandis (CEG) and Pinus taeda (CPT), obtained through the kraft and sulfite pulping processes, respectively, were characterized. Fourier transform infrared (FTIR) spectroscopy, X-ray diffraction (XRD) and thermogravimetric analysis (TGA) were carried out. From the XRD analysis the interplanar distance, crystallite size and crystallinity index were calculated and the degradation kinetics parameters were determined by TGA at heating rates of 5, 10, 20 and 40 °C min⁻¹ using the Avrami, Flynn-Wall-Ozawa (FWO) and Criado methods. The results obtained by FTIR showed that the composition of the fibers is similar, while from the XRD analysis slight differences in the crystallinity were observed. The thermogravimetric analysis showed higher thermal stability for CPT than CEG while the values for the activation energy (E_a) were higher for CEG than CPT. The results obtained by Avrami and Criado methods showed that the degradation mechanism in the CEG samples involves a diffusion process while in the case of CPT the degradation process is a phase boundary controlled reaction. The degradation mechanisms demonstrated that the difference between thermal stability and E_a may be due to differences in the type of crystalline structure of the samples obtained through the two pulping processes.     

A comparative analysis of mass losses of some aliphatic polyesters upon enzymatic degradation

Results of investigation of mass losses, geometrical surface structure changes and variations in crystallinity of poly(lactic acid) (PLA), poly(?-caprolactone) (PCL) and commercially available material (PHB) consisting of poly(3,4-hydroxybutyrate) and poly(lactic acid) are presented. These structural changes occurred due to degradation of these polymers in the presence of the following enzymes: proteinase K, protease, esterase or lipase. Independently of the enzyme type, the largest mass loss was found for PLA and the smallest for PHB. Thus, under the experimental conditions, the processes of enzymatic degradation proceeded most rapidly in PLA, more slowly in PCL, and the most slowly in PHB. It was also found that proteinase K caused the largest mass losses, protease caused smaller mass losses, and both esterase and lipase produced the least mass losses, while lipase did not bring about mass loss in PHB. Images of surfaces of individual samples, obtained by scanning electron microscopy (SEM), indirectly confirmed the results of the mass loss examination. Crystallinity of the studied polyesters increased with degradation in the presence of proteinase K and protease, while changes in the crystallinity due to esterase and lipase were not observed. The presented results illustrate well the relative susceptibilities of the individual polyesters toward degradation induced by various enzymes.     

On-line solid-phase extraction-short-column liquid chromatography combined with various tandem mass spectrometric scanning strategies for the rapid study of transformation of pesticides in surface water.

The applicability of solid-phase extraction-short-column liquid chromatography using two short columns (i.e., 10 and 20 mm long) coupled on-line with tandem mass spectrometric detection is demonstrated for the rapid degradation study of pesticides and their transformation products in water at the low-microgram/l level. Photolysis was used as a means to transform the parent compounds into their degradation products and the experiments were carried out at environmentally relevant concentrations. The use of on-line sample enrichment/separation in photodegradation studies allows the rapid analysis of aqueous samples directly after irradiation without further transformation of the compounds of interest. The versatility of MS allows various selective screening strategies to be employed, i.e., full-scan mode, neutral loss, precursor-ion and product-ion scan modes. This allows the identification of possible degradation products and the calculation of the rates of disappearance of the parent compound and appearance of transformation products.