Grafting of commercially available amines bearing aromatic rings onto poly(vinylidene‐co‐hexafluoropropene) copolymers

The grafting of poly(VDF‐co‐HFP) copolymers with different amines containing aromatic rings, such as aniline, benzylamine, and phenylpropylamine, is presented. ¹⁹F NMR characterization enabled us to show that the sites of grafting of aromatic‐containing amines were first difluoromethylene of vinylidene fluoride (VDF) in the hexafluoropropene (HFP)/VDF/HFP triad and then that of VDF adjacent to HFP. The kinetics of grafting of benzylamine, monitored by ¹H NMR spectroscopy, confirmed those sites of grafting and showed that all VDF units located between two HFPs were grafted in the first 150 min, whereas those adjacent to one HFP unit were grafted in the remaining 3000 min. Parameters such as the temperature or the molar percentage of HFP in the copolymer had an influence on the maximum rate of grafted benzylamine. The higher the temperature, the higher the molar percentage of grafted benzylamine. Furthermore, the higher the molar percentage of HFP in the copolymer, the higher the molar percentage of VDF in the HFP/VDF/HFP triad, and the higher the molar percentage of grafted benzylamine. The spacer length between the aromatic ring and the amino group had an influence on the kinetics of grafting: aniline (pK_a = 4.5) could not add onto the polymeric backbone, whereas phenylpropylamine was grafted in the first 150 min, and benzylamine required 3000 min to reach the maximum amount of grafting. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1855–1868, 2006     

Synthesis and self‐assembly of thymine‐ and adenine‐containing homopolymers and diblock copolymers

Atom transfer radical polymerizations (ATRPs) of 1‐(4‐methacryloyloxy‐benzyl)thymine (MAT) and 9‐(2‐methacryloyloxyethyl)adenine (MAA) were conducted for the synthesis of DNA‐base functionalized polymers. The association equilibrium constant K_asso between MAT and MAA and the complexation equilibrium constant K_comp between the corresponding polymers PMAT and PMAA were determined. A zipper‐like diblock copolymer, PMAT‐b‐PMAA, was prepared by anchoring the PMAT and PMAA blocks on the ortho‐positions of a pyridine ring via a successive two‐step ATRP. Dynamic light scattering and atom force microscopy confirmed that the block copolymer had a V‐shaped configuration in dimethylsulfoxide/N,N‐dimethylformamide. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5995–6006, 2006     

Preparation and morphological,electrical, and mechanical properties of polyimide‐grafted MWCNT/polyimide composite

Precursor of polyimide, polyamic acid has been prepared sucessfully. Acid‐modified carbon nanotube (MWCNT) was grafted with soluble polyimide then was added to the polyamic acid and heated to 300 °C to form polyimide/carbon nanotube composite via imidation. Morphology, mechanical properties and electrical resistivity of the MWCNT/polyimide composites have been studied. Transmission electron microscope microphotographs show that the diameter of soluble polyimide‐grafted MWCNT was increased from 30–60 nm to 200 nm, that is a thickness of 70–85 nm of the soluble polyimide was grafted on the MWCNT surface. PI‐g‐MWCNT was well dispersed in the polymer matrix. Percolation threshold of MWCNT/polyimide composites has been investigated. PI‐g‐MWCNT/PI composites exhibit lower electrical resistivity than that of the acid‐modified MWCNT/PI composites. The surface resistivity of 5.0 phr MWCNT/polyimide composites was 2.82 × 10⁸ Ω/cm² (PI‐g‐MWCNT) and 2.53 × 10⁹ Ω/cm² (acid‐modified MWCNT). The volume resistivity of 5.0 phr MWCNT/polyimide composites was 8.77 × 10⁶ Ω cm (PI‐g‐MWCNT) and 1.33 × 10¹³ Ω cm (acid‐modified MWCNT).Tensile strength and Young's modulus increased significantly with the increase of MWCNT content. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3349–3358, 2007     

Synthesis,Voltammetric and Analytical Applications of Some Fluorine Substituted Spirosteroidalthiazolidin‐4‐one Derivatives of Sulfa Drugs

A new 5‐arylidene‐4‐oxo‐(sulfonamoyl phenyl)‐spiro[thiazolidinone‐2,2′‐steroids] series (7–10) was prepared by condensation of sulfanilamide, sulfapyridine and sulfadiazine sulfa drugs with testosterone, epiandrosterone and progesterone steroids, respectively. The resultant imino derivatives 1–3 upon cycloaddition with thioacetic acid in dry 1,4‐dioxane afforded 3‐sulfo‐namoylphenylspiro[4‐oxo‐thiazolidin‐2,2′steroids] (4–6). The latter compounds (4–6) upon condensation with p‐fluorobenzaldehyde in ethanol‐piperidine yielded the corresponding 4‐fluoroarylidene derivatives 7, 8 & 9, respectively. All the newly synthesized compounds were confirmed by UV, IR, ¹H NMR, ¹³C NMR, mass spectral data, elemental analysis and molecular weight determination. In vitro antimicrobial screening of some of the synthesized compounds showed good antimicrobial activities towards some pathogenic Gram‐positive, Gram‐negative bacteria and fungi vs. piperacillin and mycostatine antibiotics as standard antibacterial and antifungal agents, respectively. The voltammetric behavior of two newly spirothiazolidinone steroids ( 2a & 5a ) was critically studied. Compound 5a physically immobilized polyurethane foam solid sorbent was successfully used for removal and/or separation of bismuth(III) from water.     

Novel 7‐Nitro‐1‐(Piperidin‐4‐yl)‐4,5‐Dihydro‐[1,2,4] Triazolo[4,3‐a]Quinoline‐Sulphonamide Derivatives as Antimicrobial Agents: Design,Synthesis, and Bio‐Activity

In attempt to search for more potent antimicrobial agents, a series of 7‐nitro‐1‐(piperidin‐4‐yl)‐4,5‐dihydro‐[1,2,4]triazolo[4,3‐a]quinoline‐derived sulphonamides were synthesized. Their structures were established by elemental analyses, IR, and NMR (¹H and ¹³C) spectral data. The antibacterial activity of the obtained compounds was investigated against different Gram‐negative (Escherichia coli and Pseudomonas aeruginosa) and Gram‐positive (Bacillus subtilis and Staphylococcus aureus) bacteria and antifungal activity against two fungal strains (Aspergillus niger and Aspergillus clavatus) using disk diffusion method at various concentrations (20, 40, 60, and 80 μg/mL). The study reveals that most of the title compounds showed significant antibacterial and fungal activity when compared with their respective standards streptomycin and griseofulvin.     

Syntheses and self‐assembly of poly(benzyl ether)‐b‐poly(N‐isopropylacrylamide) dendritic–linear diblock copolymers

This article describes the syntheses and solution behavior of model amphiphilic dendritic–linear diblock copolymers that self‐assemble in aqueous solutions into micelles with thermoresponsive shells. The investigated materials are constructed of poly(benzyl ether) monodendrons of the second generation ([G‐2]) or third generation ([G‐3]) and linear poly(N‐isopropylacrylamide) (PNIPAM). [G‐2]‐PNIPAM and [G‐3]‐PNIPAM dendritic–linear diblock copolymers have been prepared by reversible addition–fragmentation transfer (RAFT) polymerizations of N‐isopropylacrylamide with a [G‐2]‐ or [G‐3]‐based RAFT agent, respectively. The critical micelle concentration (cmc) of [G‐3]‐PNIPAM₂₂₀, determined by surface tensiometry, is 6.3 × 10^?6 g/mL, whereas [G‐2]‐PNIPAM₂₃₅ has a cmc of 1.0 × 10^?5 g/mL. Transmission electron microscopy results indicate the presence of spherical micelles in aqueous solutions. The thermoresponsive conformational changes of PNIPAM chains located at the shell of the dendritic–linear diblock copolymer micelles have been thoroughly investigated with a combination of dynamic and static laser light scattering and excimer fluorescence. The thermoresponsive collapse of the PNIPAM shell is a two‐stage process; the first one occurs gradually in the temperature range of 20–29 °C, which is much lower than the lower critical solution temperature of linear PNIPAM homopolymer, followed by the second process, in which the main collapse of PNIPAM chains takes place in the narrow temperature range of 29–31 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1357–1371, 2006     

Hairy polymeric nanocapsules with ph‐responsive shell and thermoresponsive brushes: Tunable permeability for controlled release of water‐soluble drugs

The hairy poly(methacrylic acid‐co‐divinylbenzene)‐g‐poly(N‐isopropylacrylamide) (P(MAA‐co‐DVB)‐g‐PNIPAm) nanocapsules with pH‐responsive P(MAA‐co‐DVB) inner shell and temperature‐responsive PNIPAm brushes were prepared by combined distillation–precipitation copolymerization and surface thiol‐ene click grafting reaction using 3‐(trimethoxysilyl)propyl methacrylate‐modified silica (SiO₂‐MPS) nanospheres as a sacrificial core material. The well‐defined PNIPAm was synthesized by a reversible addition fragmentation chain transfer (RAFT) polymerization. The chain end was converted to a thiol by chemical reduction. The PNIPAm was integrated into the nanocapsules via thiol‐ene click reaction. The surface thiol‐ene click reaction conduced to tunable grafting density of PNIPAm brushes. The grafting densities decreased from 0.70 chains nm^?2 to 0.15 chains nm^?2 with increasing the molecular weight of grafted PNIPAm chains. Using water soluble doxorubicin hydrochloride (DOX·HCl) as a model molecular, the tunable shell permeability of the nanocapsule was investigated in detail. The permeability constant can be tuned by controlling the thickness of the P(MAA‐co‐DVB) inner shell, the grafting density of PNIPAm brushes, and the environmental pH and temperature. The tunable shell permeability of these nanocapsules results in the release of the loaded guest molecules with manipulable releasing kinetics. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2202–2216     

The preparation and characterization of carboxylic acid‐coated silica nanoparticles

The preparation of carboxylic acid‐coated silica nanoparticles was investigated. A monolayer of carboxylic acid residues with controllable graft density was anchored to the nanoparticle by a ring‐opening reaction with succinic anhydride. Poly(methacrylic acid) [poly(MAA)] grafted nanoparticles were prepared via a polymerization–deprotection strategy. Tert‐butyl methacrylate was polymerized from the surface of silica nanoparticles in a predictable manner and with excellent control over the molecular weight distribution. Subsequent removal of the tert‐butyl group resulted in poly (MAA) grafted nanoparticles. The polymer nanoparticles were also functionalized with dyes, which may be useful in tracking the particles in biological systems. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Silver(I)‐N‐heterocyclic carbene complexes of bis‐imidazol‐2‐ylidenes having different aromatic‐spacers: synthesis,crystal structure,and in vitro antimicrobial and anticancer studies

A series of Ag(I) complexes ( 6 , 7 , 8 , 9 ) derived from imidazol‐2‐ylidenes was synthesized by reacting Ag₂O with an o‐, m‐, p‐xylyl or 1,3,5‐triazine‐linked imidazolium salts ( 1 , 2 , 3 , 4 ) and then characterizing these using various spectro‐analytical techniques. Additionally, triazine‐linked bis‐imidazolium salt 5 was characterized using the single‐crystal X‐ray diffraction method. Complexes 6–9 were formed from the N‐heterocyclic carbene ligand precursors 1–3 as PF₆^‐ salts in good yields. Conversely, salt 5 does not form Ag(I) complex even under various reaction conditions. Using ampicillin as a standard, complexes 6–9 were tested against bacteria strains Escherichia coli and Staphylococcus aureus as Gram‐negative and Gram‐positive bacteria, respectively, showing potent antimicrobial activities against the tested bacteria even at minimum inhibition concentration and bacterial concentration levels. Furthermore, the potential anticancer activities of the reported complexes were evaluated against the human colorectal cancer (HCT 116) cell lines, using 5‐fluorouracil as a standard drug. The highest anticancer activities were observed for complex 8 with an IC₅₀ value of 3.4 μm , whereas the lowest was observed for complex 9 with an IC₅₀ value of 18.1 μm . Copyright © 2013 John Wiley & Sons, Ltd.     

Poly(ϵ‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(ϵ‐caprolactone) triblock copolymers: Synthesis and self‐assembly in aqueous solutions

Nontoxic and biodegradable poly(?‐caprolactone)‐b‐poly(ethylene glycol)‐b‐poly(?‐caprolactone) triblock copolymers were synthesized by the solution polymerization of ?‐caprolactone in the presence of poly(ethylene glycol). The chemical structure of the resulting triblock copolymer was characterized with ¹H NMR and gel permeation chromatography. In aqueous solutions of the triblock copolymers, the micellization and sol–gel‐transition behaviors were investigated. The experimental results showed that the unimer‐to‐micelle transition did occur. In a sol–gel‐transition phase diagram obtained by the vial‐tilting method, the boundary curve shifted to the left, and the gel regions expanded with the increasing molecular weight of the poly(?‐caprolactone) block. In addition, the hydrodynamic diameters of the micelles were almost independent of the investigated temperature (25–55 °C). The atomic force microscopy results showed that spherical micelles formed at the copolymer concentration of 2.5 × 10^?4 g/mL, whereas necklace‐like and worm‐like shapes were adopted when the concentration was 0.25 g/mL, which was high enough to form a gel. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 605–613, 2007     

Facile Heterocyclic Synthesis and Antibacterial Activity of Substituted Isoxazol‐5(4H)‐ones

An efficient, simple, and green procedure for the synthesis of isoxazol‐5(4H)‐one derivatives are described here through a convenient one‐pot, three‐component reaction at room temperature. The title compounds are isolated in high to excellent yields and after short reaction times, and are characterized by various spectroscopic methods such as IR, ¹H NMR, and ¹³C NMR. The synthesized compounds 4a–c and 4e–i were tested for their in vitro activity against a panel of Gram‐positive and Gram‐negative bacteria, demonstrating their ability to inhibit microorganisms with a zone of inhibition ranging from 15 to 30 mm, minimum inhibitory concentration between 250 and 900 μg/mL, and minimum bacterial concentration between 700 and 1000 μg/mL.     

Surface modification of multiwalled carbon nanotubes via nitroxide‐mediated radical polymerization

The nitroxide‐mediated radical polymerization of styrene was carried out on the surfaces of multiwalled carbon nanotubes (MWNTs) initiated by an MWNT‐supported initiator multiwalled carbon nanotube–2″,2″,6″,6″‐tetramethylpiperidinyloxy (MWNT–Tempo). The content of polystyrene grafted from the surface was controlled by changes in the polymerization conditions, such as the reaction times or the ratios of monomers to initiators. The obtained polystyrene‐grafted multiwalled carbon nanotubes (MWNT–PSs) were further used to initiate the polymerization of 4‐vinylpyridine to get polystyrene‐b‐poly(4‐vinylpyridine)‐grafted multiwalled carbon nanotubes (MWNT–PS‐b‐P4VPs). In contrast to unmodified MWNTs, MWNT–PSs had relatively good dispersibility in various organic solvents, such as tetrahydrofuran, CHCL₃, and o‐dichlorobenzene. The structures and properties of MWNT–PSs and MWNT–PS‐b‐P4VPs were characterized and studied with several methods, including thermogravimetric analysis, Fourier transform infrared, ultraviolet–visible, and transmission electron microscopy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4656–4667, 2006     

Functionalized multi‐walled carbon nanotubes with poly(N‐(2‐hydroxypropyl)methacrylamide) by RAFT polymerization

In this study, we grafted water‐soluble biocompatible polymer, poly(N‐(2‐hydroxypropyl)methacrylamide) (PHPMA), onto the surface of multi‐walled carbon nanotubes (MWNTs). The reversible addition‐fragmentation chain transfer (RAFT) agents, dithioesters, were successfully immobilized onto the surface of MWNTs first, PHPMA chains were then subsequently grafted onto MWNTs via RAFT polymerization by using dithioesters immobilized on MWNTs as RAFT agent. FTIR, XPS, ¹H NMR, Raman and TGA were used to characterize the resulting products and to determine the content of water‐soluble PHPMA chains in the product. The MWNTs grafted with PHPMA chains have good solubility in distilled water, PBS buffer, and methanol. TEM images of the samples provide direct evidence for the formation of a nanostructure that MWNTs coated with polymer layer. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 2419–2427, 2006     

Synthesis and characteristics of poly(N‐isopropylacrylamide‐co‐methacrylic acid)/Fe3O4 thermosensitive magnetic composite hollow latex particles

In this study, the poly(NIPAAm–MAA)/Fe₃O₄ hollow latex particles were synthesized by three steps. The first step was to synthesize the poly(methyl methacrylate‐co‐methylacrylate acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. Following the first step, the second step was to polymerize N‐isopropylacrylamide (NIPAAm), MAA, and crosslinking agent (N,N'‐methylene‐bisacrylamide (MBA)) in the presence of poly(MMA‐MAA) latex particles to form the linear poly(MMA‐MAA)/crosslinking poly (NIPAAm‐MAA) core‐shell latex particles. After the previous processes, the core‐shell latex particles were heated in the presence of NH₄OH to dissolve the linear poly(MMA‐MAA) core in order to form the poly(NIPAAm‐MAA) hollow latex particles. In the third step, Fe²⁺ and Fe³⁺ ions were introduced to bond with the ? COOH groups of MAA segments in the poly(NIPAAm‐MAA) hollow polymer latex particles. Further by a reaction with NH₄OH and then Fe₃O₄ nanoparticles were generated in situ and the poly(NIPAAm‐MAA)/Fe₃O₄ magnetic composite hollow latex particles were formed. The concentrations of MAA, crosslinking agent (N,N'‐methylene bisacrylamide), and Fe₃O₄ nanoparticles were important factors to influence the morphology of hollow latex particles and lower critical solution temperature of poly(NIPAAm–MAA)/Fe₃O₄ magnetic composite hollow latex particles. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Development and validation of a UPLC‐MS/MS method for the determination of 7‐hydroxymitragynine,a μ‐opioid agonist,in rat plasma and its application to a pharmacokinetic study

A simple, sensitive and specific ultra‐performance liquid chromatography–tandem mass spectrometry (UPLC‐MS/MS) method was developed and validated to determine the concentrations of 7‐hydroxymitragynine in rat plasma. Following a single‐step liquid–liquid extraction of plasma samples using chloroform, 7‐hydroxymitragynine and the internal standard (tryptoline) were separated on an Acquity UPLC^TM BEH C₁₈ (1.7 µm, 2.1 × 50 mm) column using an isocratic elution at a flow rate of 0.2 mL/min. The mobile phase consisted of 0.1% acetic acid in water and 0.1% acetic acid in acetonitrile (10:90, v/v). The run time was 2.5 min. The analysis was carried out under the multiple reaction‐monitoring mode using positive electrospray ionization. Protonated ions [M + H]⁺ and their respective product ions were monitored at the following transitions: 415 → 190 for 7‐hydroxymitragynine and 173 → 144 for the internal standard. The calibration curve was linear over the range of 10–4000 ng/mL (r² = 0.999) with a lower limit of quantification of 10 ng/mL. The extraction recoveries ranged from 62.0 to 67.3% at concentrations of 20, 600 and 3200 ng/mL). Intra‐ and inter‐day assay precisions (relative standard deviation) were <15% and the accuracy was within 96.5–104.0%. This validated method was successfully applied to quantify 7‐hydroxymitragynine in rat plasma following intravenous administration. Copyright © 2013 John Wiley & Sons, Ltd.     

Reinforcement effect of MAA on nano‐CaCo3‐filled EPDM vulcanizates and possible mechanism

Methacrylic acid (MAA) was used as in situ surface modifier to improve the interface interaction between nano‐CaCO₃ particle and ethylene–propylene–diene monomer (EPDM) matrix, and hence the mechanical properties of nano‐CaCO₃‐filled EPDM vulcanizates. The results showed that the incorporation of MAA improved the filler–matrix interaction, which was proved by Fourier transformation infrared spectrometer (FTIR), Kraus equation, crosslink density determination, and scanning electron microscope (SEM). The formation of carboxylate and the participation of MAA in the crosslinking of EPDM indicated the strong filler–matrix interaction from the aspect of chemical reaction. The results of Kraus equation showed that the presence of MAA enhanced the reinforcement extent of nano‐CaCO₃ on EPDM vulcanizates. Crosslink density determination proved the formation of the ionic crosslinks in EPDM vulcanizates with the existence of MAA. The filler particles on tensile fracture were embedded in the matrix and could not be observed obviously, indicating that a strong interfacial interaction between the filler and the matrix had been achieved with the incorporation of MAA. Meanwhile, the presence of MAA remarkably increased the modulus and tensile strength of the vulcanizates, without negative effect on the high elongation at break. Furthermore, the ionic bond was thought to be formed only on filler surface because of the absolute deficiency of MAA, which resulted in the possible structure where filler particles were considered as crosslink points. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1226–1236, 2006     

新型5-(对氯苯基)-3-(邻，对-二氯苯基)-4，5-二氢吡唑肟酯衍生物的合成，结构表征及抗菌活性

合成了10个未见文献报道的1-(5-(2-氯苯基)-3-(2,4-二氯苯基)-4,5-二氢-N-吡唑肟酯类衍生物,并经过元素分析、HRMS、核磁共振氢谱对其结构进行了表征。对新合成的化合物进行了初步抗Bacillus subtilis, Staphylococcus aureus, Escherichia coli 和 Pseudomonas aeruginosa生物活性测试,结果表明:化合物7c 和7f对供试病菌具有较好的体外杀灭活性,其MIC值达到1.562 μg/mL;化合物7c ,7d和7f 具有中等的抑制DNA回旋酶活性(IC₅₀ = 1.6~2.5 µg/mL)。在生物活性结果的基础上对系列化合物的构效关系进行了初步的探讨。     

Synthesis and characteristics of poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles and their application as drug carriers

In this work, the poly(methacrylic acid‐co‐N‐isopropylacrylamide) thermosensitive composite hollow latex particles was synthesized by a three‐step reaction. The first step was to synthesize the poly(methyl methacrylate‐co‐methacrylic acid) (poly(MMA‐MAA)) copolymer latex particles by the method of soapless emulsion polymerization. The second step was to polymerize methacrylic acid (MAA), N‐isopropylacrylamide (NIPAAm), and N,N′‐methylenebisacrylamide in the presence of poly(MMA‐MAA) latex particles to form the linear poly(methyl methacrylate‐co‐methacrylic acid)/crosslinking poly(methacrylic acid‐co‐N‐isopropylacrylamide) (poly(MMA‐MAA)/poly(MAA‐NIPAAm)) core–shell latex particles. In the third step, the core–shell latex particles were heated in the presence of ammonia solution to form the crosslinking poly(MAA‐NIPAAm) thermosensitive hollow latex particles. The morphologies of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were observed. The influences of crosslinking agent and shell composition on the lower critical solution temperature of poly(MMA‐MAA)/poly(MAA‐NIPAAm) core–shell latex particles and poly(MAA‐NIPAAm) hollow latex particles were, respectively, studied. Besides, the poly(MAA‐NIPAAm) thermosensitive hollow latex particles were used as carriers to load with the model drug, caffeine. The effect of various variables on the amount of caffeine loading and the efficiency of caffeine release was investigated. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 5203–5214     

Synthesis,hole mobility,and photovoltaic properties of two alternating poly[3‐(hex‐1‐enyl)thiophene‐co‐thiophene]s

Two alternating poly[3‐(hex‐1‐enyl)thiophene‐co‐thiophene]s, Pa (with 77% trans‐isomer and 23% cis‐isomer) and Pb (with 100% trans‐isomer), were synthesized by the coupling of 2,5‐dibromo‐3‐hex‐1‐enyl‐thiophene to 2,5‐bis(tributylstannyl)thiophene via a Stille reaction and compared with poly(3‐hexylthiophene‐co‐thiophene) ( P1 ) to study the effect of changing the carbon(α)–carbon(β) single bond into a carbon–carbon double bond on the properties of the polymers. From P1 to Pb and to Pa , the ultraviolet–visible absorption peaks of the polymers were slightly redshifted, and their electrochemical bandgaps decreased by 0.05–0.1 eV. X‐ray diffraction analysis indicated that Pa had a better lamellar structure than Pb . The hole mobilities of the three polymers, determined with the space‐charge‐limited current model, were 5.23 × 10^?6 ( P1 ), 2.34 × 10^?4 ( Pb ), and 7.02 × 10^?4 cm²/V s ( Pa ). The power conversion efficiencies (PCEs) of polymer solar cells based on the three polymers were 0.87 ( P1 ), 1.16 ( Pb ), and 1.70% ( Pa ). The increase in the hole mobility and PCE revealed the important effect of changing the carbon(α)–carbon(β) single bond into a carbon–carbon double bond on the properties of polythiophene derivatives containing 3‐alkylthiophene. The strategy used in this work enlarges the thinking to obtain novel, efficient donor polymers for optoelectronic applications. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 629–638, 2007     

Synthesis and characteristics of poly(N‐isopropylacrylamide‐co‐methacrylic acid)/Fe3O4/poly(N‐isopropylacrylamide‐co‐methacrylic acid) two‐shell thermosensitive magnetic composite hollow latex particles

In this study, the poly(N‐isopropylacrylamide‐methylacrylate acid)/Fe₃O₄/poly(N‐isopropylacrylamide‐methylacrylate acid) (poly(NIPAAm‐MAA)/Fe₃O₄/poly(NIPAAm‐MAA)) two‐shell magnetic composite hollow latex particles were synthesized by four steps. The poly(methyl methacrylate‐co‐methylacrylate acid) (poly(MMA‐MAA)) copolymer latex particles were synthesized first. Then, the second step was to polymerize NIPAAm, MAA, and crosslinking agent in the presence of poly(MMA‐MAA) latex particles to form the linear poly(MMA‐MAA)/crosslinking poly(NIPAAm‐MAA) core–shell latex particles. Then, the core–shell latex particles were heated in the presence of NH₄OH to dissolve the linear poly(MMA‐MAA) core to form the poly(NIPAAm‐MAA) hollow latex particles. In the third step, the Fe₃O₄ nanoparticles were generated in the presence of poly(NIPAAm‐MAA) hollow polymer latex particles and formed the poly(NIPAAm‐MAA)/Fe₃O₄ magnetic composite hollow latex particles. The fourth step was to synthesize poly(NIPAAm‐MAA) in the presence of poly(NIPAAm‐MAA)/Fe₃O₄ latex particles to form the poly(NIPAAm‐MAA)/Fe₃O₄/poly(NIPAAm‐MAA) two‐shell magnetic composite hollow latex particles. The effect of various variables such as reactant concentration, monomer ratio, and pH value on the morphology and volume‐phase transition temperature of two‐shell magnetic composite hollow latex particles was studied. Moreover, the latex particles were used as carriers to load with caffeine, and the caffeine‐loading characteristics and caffeine release rate of latex particles were also studied. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2880–2891