New p–ρ–T measurements up to 70 MPa for the system CO2 + propane between 298 and 343 K at near critical compositions

The vibrating tube densimeter method along with the Forced Path Mechanical Calibration model, is used to measure the high pressure isothermal p–ρ behavior of the CO₂+propane system along 17 isotherms between 293 and 343 K, at pressures up to 70 MPa. The compositions cover the range of mole fractions from x_CO2=0.45 to 1.0. The uncertainty in temperatures is ±0.015 K. The uncertainties in pressures are ±0.0013 MPa from 0.1 to 15.0 MPa and ±0.010 MPa from 5.0 to 70.0 MPa. The precision of the density measurements is ±0.014 kg m⁻³. The minimum global uncertainty is ±0.204 kg m⁻³, based on the calibration of the densimeter with pure water. A generalized Helmholtz energy model for mixtures is used to check the consistency of the new data with respect to previous p–ρ–T studies of this mixture. The average absolute deviation of our data with respect to the model is 0.64% which is fully consistent with the assessed accuracy.     

Equilibrium diagram of KPO3–Y(PO3)3 system, chemical preparation and characterization of KY(PO3)4

Microdifferential thermal analysis (μ-DTA), X-ray diffraction (XRD) and infrared (IR) spectroscopy were used for the first time to investigate the liquidus and solidus relations in the KPO₃–Y(PO₃)₃ system. The only compound observed within the system was KY(PO₃)₄ melting incongruently at 1033 K. An eutectic appears at 13.5 mol% Y(PO₃)₃ at 935 K, the peritectic occurs at 1033 K and the phase transition for potassium polyphosphate KPO₃ was observed at 725 K. Three monoclinic allotropic phases of the single crystals were obtained. KY(PO₃)₄ polyphosphate has the P2₁ space group with lattice parameters: a=7.183(4) Å, b=8.351(6) Å, c=7.983(3) Å, β=91.75(3)° and Z=2 is isostructural with KNd(PO₃)₄. The second allotropic form of KY(PO₃)₄ belongs to the P2₁/n space group with lattice parameters: a=10.835(3) Å, b=9.003(2) Å, c=10.314(1) Å, β=106.09(7)° and Z=4 and is isostructural with TlNd(PO₃)₄. The IR absorption spectra of the two forms show a chain polyphosphates structure. The last modification of KYP₄O₁₂ crystallizes in the C2/c space group with lattice parameters: a=7.825(3) Å, b=12.537(4) Å, c=10.584(2) Å, β=110.22(7)° and Z=4 is isostructural with RbNdP₄O₁₂ and contains cyclic anions. The methods of chemical preparations, the determination of crystallographic data and IR spectra for these compounds are reported.     

Syntheses, crystal structures and electronic properties of a series of copper(II) complexes with 3,5-halogen-substituted Schiff base ligands and their solutions

We have systematically investigated the structural features, electronic properties, thermally-induced structural phase transitions and absorption spectra depending on the solvent for ten Cu(II) complexes with 3,5-halogen-substituted Schiff base ligands. Structural characterization of two new complexes, bis(N-R-1-phenylethyl- and N-R,S-2-butyl-5-bromosalicydenaminato-κ²N,O)copper(II), reveals that they afford a compressed tetrahedral trans-[CuN₂O₂] coordination geometry with trans-N–Cu–N = 159.4(2)° and trans-O–Cu–O = 151.7(3)° for the 1-phenylethyl complex and trans-N–Cu–N = 157.9(3)° and trans-O–Cu–O = 151.0(3)° for the 2-butyl one. All the complexes exhibit a structural phase transition by heating in the solid state regardless of their structures at room temperature. The absorption spectra of a series of ten complexes exhibit a slight shift of the d–d band at 16 000–20 000 cm⁻¹ and remarkable shift of the π–π* band at 24 000–28 000 cm⁻¹, which suggests that the dipole moment of the solvents presumably affects the conformation of the π-conjugated moieties of the ligands rather than the coordination environment. We have also attempted ‘photochromic solute-induced solvatochromism’ by a system of bis(N-R-1-phenylethyl-3,5-dichlorosalicydenaminato-κ²N,O)copper(II) and photochromic 4-hydroxyazobenzene in chloroform solution. We successfully observed a change of the d–d and π–π* bands of the complex in the absorption spectra caused by cis–trans photoisomerization of 4-hydroxyazobenzene.     

The efficacy of nitrosonaphthol functionalized XAD-16 resin for the preconcentration/sorption of Ni(II) and Cu(II) ions

Amberlite XAD-16 resin has been functionalized using nitrosonaphthol as a ligand and characterized employing elemental, thermogravimetric analysis and FT-IR spectroscopy. The sorption of Ni(II) and Cu(II) ions onto this functionalized resin is investigated and optimized with respect to the sorptive medium (pH), shaking speed and equilibration time between liquid and solid phases. The monitoring of the influence of diverse ions on the sorption of metal ions has revealed that phosphate, bicarbonate and citrate reduce the sorption up to 10–14%. The sorption data followed Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherms. The Freundlich parameters computed are 1/n = 0.56 ± 0.03 and 0.49 ± 0.05, A = 9.54 ± 1.5 and 6.0 ± 0.5 mmol g⁻¹ for Ni(II) and Cu(II) ions, respectively. D–R isotherm yields the values of X_m = 0.87 ± 0.07 and 0.35 ± 0.05 mmol g⁻¹ and of E = 9.5 ± 0.23 and 12.3 ± 0.6 kJ mol⁻¹ for Ni(II) and Cu(II) ions, respectively. Langmuir characteristic constants estimated are Q = 0.082 ± 0.005 and 0.063 ± 0.003 mmol g⁻¹, b = (4.7 ± 0.2) × 10⁴ and (7.31 ± 0.11) × 10⁴ l mol⁻¹ for Ni(II) and Cu(II) ions, respectively. The variation of sorption with temperature gives thermodynamic quantities of ΔH = −58.9 ± 0.12 and −40.38 ± 0.11 kJ mol⁻¹, ΔS = −183 ± 10 and −130 ± 8 J mol⁻¹ K⁻¹ and ΔG = −4.4 ± 0.09 and −2.06 ± 0.08 kJ mol⁻¹ at 298 K for Ni(II) and Cu(II) ions, respectively. Using kinetic equations, values of intraparticle transport and of first order rate constant have been computed for both the metal ions. The sorption procedure is utilized to preconcentrate these ions prior to their determination in tea, vegetable oil, hydrogenated oil (ghee) and palm oil by atomic absorption spectrometry using direct and standard addition methods.     

Synthesis and characterization of [chloro{2(1H)-pyridinethione-S}{tris(pyridin-2-ylthiolato)methyl-C,N,N′,N″]}nickel(II)], [Ni(TPTM)(SPyH)Cl]

The compound, [chloro{2(1H)-pyridinethione-S}{tris(pyridin-2-ylthiolato)methyl-C,N,N′,N″]}nickel(II)], [Ni(TPTM)(SPyH)Cl], was isolated from the reaction between NiCl₂ · 6H₂O and tris(pyridin-2-ylthiolato)methane in aqueous EtOH. X-ray crystallography at 120 K revealed an octahedral arrangement about Ni with a tetradentate tris(pyridin-2-ylthio)methyl-C,N,N,N ligand, a monodentate 2(1H)-pyridinethione-S ligand and a chloride. The 2(1H)-pyridinethione-S ligand was derived from tris(pyridin-2-ylthio)methane probably via an acid catalysed hydrolysis reaction. Intramolecular N–H–Cl and C–H–Cl interactions help to cement the molecular structure. Weak C–H–Cl and C–H–S hydrogen bonding interactions link molecules of [Ni(TPTM)(SPyH)Cl] into a 3D array. EPR and UV spectra, and Hartree–Fock theoretical calculations are reported.     

Heat capacity and thermodynamic properties of N-(2-cyanoethyl) aniline (C9H10N2)

The low temperature heat capacities of N-(2-cyanoethyl)aniline were measured with an automated adiabatic calorimeter over the temperature range from 83 to 353 K. The temperature corresponding to the maximum value of the apparent heat capacity in the fusion interval, molar enthalpy and entropy of fusion of this compound were determined to be 323.33 ± 0.13 K, 19.4 ± 0.1 kJ mol⁻¹ and 60.1 ± 0.1 J K⁻¹ mol⁻¹, respectively. Using the fractional melting technique, the purity of the sample was determined to be 99.0 mol% and the melting temperature for the tested sample and the absolutely pure compound were determined to be 323.50 and 323.99 K, respectively. A solid-to-solid phase transition occurred at 310.63 ± 0.15 K. The molar enthalpy and molar entropy of the transition were determined to be 980 ± 5 J mol⁻¹ and 3.16 ± 0.02 J K⁻¹ mol⁻¹, respectively. The thermodynamic functions of the compound [H_T − H_298.15] and [S_T − S_298.15] were calculated based on the heat capacity measurements in the temperature range of 83–353 K with an interval of 5 K.     

Kinetics study of the gas-phase reactions of C2F5OC(O)H and n-C3F7OC(O)H with OH radicals at 253–328 K

The rate constants, k₁ and k₂ for the reactions of C₂F₅OC(O)H and n-C₃F₇OC(O)H with OH radicals were measured using an FT-IR technique at 253–328 K. k₁ and k₂ were determined as (9.24 ± 1.33) × 10⁻¹³ exp[−(1230 ± 40)/T] and (1.41 ± 0.26) × 10⁻¹² exp[−(1260 ± 50)/T] cm³ molecule⁻¹ s⁻¹. The random errors reported are ±2 σ, and potential systematic errors of 10% could add to the k₁ and k₂. The atmospheric lifetimes of C₂F₅OC(O)H and n-C₃F₇OC(O)H with respect to reaction with OH radicals were estimated at 3.6 and 2.6 years, respectively.     

Biphasic asymmetric hydroformylation and hydrogenation by water-soluble rhodium and ruthenium complexes of sulfonated (R)-2,2′-bis(diphenylphosphino)-1,1′-binaphthyl in ionic liquids

A biphasic catalytic system with water-soluble rhodium complexes of sulfonated (R)-2,2′-bis(diphenylphosphino)-1,1′-binaphthyl (labeled as (R)-BINAPS) in ionic liquid BMI·BF₄ has been developed for the asymmetric hydroformylation of vinyl acetate under mild conditions. The corresponding ruthenium complexes have been investigated for the biphasic asymmetric hydrogenation of dimethyl itaconate. The biphasic asymmetric hydroformylation of vinyl acetate provided 28.2% conversion and 55.2% enantiomeric excess when BMI·BF₄–toluene was used as the reaction medium at 333 K and 1.0 MPa for 24 h. The biphasic asymmetric hydrogenation of dimethyl itaconate in BMI·BF₄–ⁱPrOH at 333 K and 2.0 MPa afforded 65% enantiomeric excess with an activity similar to the homogenous analogs. Both biphasic catalytic systems with (R)-BINAPS ligand could be reused several times without significantly decrease in the activity, enantio- and regio-selectivities. The effects of properties of ionic liquid, molar ratio of ligand to rhodium, temperature, pressure and reaction time have been discussed.     

Synthesis and crystal structure of two novel nickel (imidazole) complexes having hydrogen-bonded networks

Two nickel (imidazole) complexes, Ni(im)₆Cl₂·4H₂O (1) and Ni(im)₆(NO₃)₂ (2) (im=imidazole) have been synthesized and characterized by elemental analysis, IR, UV, TG and single crystal X-ray diffraction. 1 crystallizes in the triclinic space group P-1 with a=8.800(6) Å, b=9.081(6) Å, c=10.565(7) Å, =75.058(9)°, β=83.143(8)°, γ=61.722(8)°, V=718.3(8) Å³, Z=1 and R₁ (wR₂)=0.0469 (0.1497). 2 crystallizes in the trigonal space group R-3 with a=12.370(6) Å, b=12.370(6) Å, c=14.782(14) Å, =90.00°, β=90.00°, γ=120.00°, V=1959(2) Å³, Z=3 and R₁ (wR₂)=0.0358 (0.0955). 1 and 2 exhibit different supramolecular network due to their different counter anions and different hydrogen bonding connection. In compound 1, [Ni(im)₆]²⁺ cation and counter anions Cl⁻ alternatively array in an ABAB fashion via N–HCl hydrogen bonding. In compound 2, the plane of each NO₃²⁻ is almost parallel and each NO₃²⁻ connect three different [Ni(im)₆]²⁺ cations via N–HO hydrogen bonding.     

Synthesis and crystal structures of two new lead(II) hexafluoroarsenates(V)

In the system PbF₂/AsF₅/anhydrous hydrogen fluoride (aHF) two new lead(II) hexafluoroarsenates(V) Pb(HF)(AsF₆)₂ and PbFAsF₆ were isolated. Pb(HF)(AsF₆)₂ is formed when the molar ratio AsF₅:PbF₂ is 2 or higher. It crystallizes in the space group Pbcn with a=1058.3(3) pm, b=1520.9(6) pm, c=1079.4(3) pm, V=1.7374(10) nm³ and Z=8. The HF molecule is directly connected to the Pb center, eight fluorine atoms from three different AsF₆⁻ ions (Pb–F distances ranging from 248(4) to 276(2) pm) and one further fluorine at 306(3) pm complete the coordination sphere. PbFAsF₆ is obtained when equimolar amounts of PbF₂ and AsF₅ react in aHF. PbFAsF₆ crystallizes in the space group P with: a=466.10(10) pm, b=723.70(10) pm, c=747.40(10) pm, =105.930(10)°, β=101.49(2)°, γ=90.660(10)°, V=0.23698(7) nm³ and Z=2. The basic unit in the structure of PbF(AsF₆) consists of a four-membered ring of two Pb and two F atoms. The Pb atoms in the ring are further connected by two AsF₆⁻ units via cis-fluorine bridges, thus forming a [PbF(AsF₆)]₂ cluster, which interacts by additional Pb–F bonds thus forming a ribbon-like polymer.     

Thermal stability and related thermodynamic properties of N-ethylthiourea

The enthalpy and entropy of sublimation of N-ethylthiourea were obtained from the temperature dependence of its vapour pressure measured by both the torsion–effusion and the Knudsen effusion method in the temperature range 360–380 K. The compound undergoes no solid-to-solid phase transition or decomposition below 380 K. The pressure against reciprocal temperature resulted in lg(p, kPa) = (13.40 ± 0.27) − (6067 ± 102) /T(K). The molar sublimation enthalpy and entropy at the mid interval temperature were Δ_subH_m(370 K) = (116.1 ± 2.0) kJ mol⁻¹ and Δ_subS_m(370 K) = (218.0 ± 5.2) J mol⁻¹ K⁻¹, respectively. The same quantities derived at 298.15 K were (118.8 ± 2.1) kJ mol⁻¹ and (226.1 ± 5.5) J mol⁻¹ K⁻¹, respectively.     

Structural and theoretical studies of Xe(OChF5)2 and [XeOChF5][AsF6] (Ch = Se, Te)

The XeOSeF₅⁺ cation has been synthesized for the first time and characterized in solution by ¹⁹F, ⁷⁷Se and ¹²⁹Xe NMR spectroscopy and in the solid state by X-ray crystallography and Raman spectroscopy with AsF₆⁻ as its counter anion. The X-ray crystal structures of the tellurium analogue and of the Xe(OChF₅)₂ derivatives have also been determined: [XeOChF₅][AsF₆] crystallize in tetragonal systems, P4/n, a=6.1356(1) Å, c=13.8232(2) Å, V=520.383(14) Å³, Z=2 and R₁=0.0453 at −60°C (Te) and a=6.1195(7) Å, c=13.0315(2) Å, V=488.01(8) Å³, Z=2 and R₁=0.0730 at −113°C (Se); Xe(OTeF₅)₂ crystallizes in a monoclinic system, P2₁/c, a=10.289(2) Å, b=9.605(2) Å, c=10.478(2) Å, β=106.599(4)°, V=992.3(3) Å³, Z=4 and R₁=0.0680 at −127°C; Xe(OSeF₅)₂ crystallizes in a triclinic system, , a=8.3859(6) Å, c=12.0355(13) Å, V=732.98(11) Å³, Z=3 and R₁=0.0504 at −45°C. The energy minimized geometries and vibrational frequencies of the XeOChF₅⁺ cations and Xe(OChF₅)₂ were calculated using density functional theory, allowing for definitive assignments of their experimental vibrational spectra.     

Synthesis and application of poly(ethylene glycol)-cholesterol (Chol-PEGm) conjugates in physicochemical characterization of nonionic surfactant vesicles

Vesicles possessing poly(ethylene glycol) (PEG) chains on their surface have been described as a blood-persistent drug delivery system with potential applications for intravenous drug administration. In this research with different molecular weights (400–10,000 g/mol) of PEG, a series of Chol–PEG^m conjugates were generated by the DCC (N,N′-dicyclohexylcarbodiimide, DCC)/(4-dimethylaminopyridine, 4-DMAP) esterification method, and confirmed by FT-IR and ¹H NMR spectrum. Then their properties in aqueous solution were studied by electron microscopy images, associative behavioral and systematic tensiometric studies over a wide concentration range. In order to elucidate the application of this Chol–PEG^m in vesicles, conventional nonionic surfactant vesicles (niosomes) composed of span 60 and cholesterol were prepared and the influence of various hydrophilic chains of the Chol–PEG^m conjugates was investigated. Results indicated that all the niosomes prepared, with or without Chol–PEG^m composition were similar in micrograph with diameter between 120 nm and 180 nm. The fixed aqueous layer thickness (FALT) around niosomes increased as Chol–PEG^m chain length increase, particularly in the Chol–PEG^10,000 modified niosomes with 9.33 ± 0.67 nm. In vitro release experiments indicated that release rate of nimodipine from Chol–PEG^m modified niosomes was enhanced. Chol–PEG^m modified niosomes showed greater accumulative release than that of plain niosomes over a period of 24 h. These studies have shed some light on the suitability of Chol–PEG^m containing niosome preparation.     

Structural and spectroscopic properties of Hexamethylenetetramine cobalt(II) complex: [Co(NCS)2(hmt)2(H2O)2][Co(NCS)2(H2O)4] (H2O)

Synthesis, structure, spectroscopy and thermal properties of complex [Co(NCS)₂(hmt)₂(H₂O)₂][Co(NCS)₂(H₂O)₄] (H₂O) (I), assembled by hexamethylenetetramine and octahedral Co(II) metal ions, are reported. Crystal data for I: F_w 387.34, a=9.020(8), b=12.887(9), c=7.95(1) Å, =96.73(4), β=115.36(5), γ=94.16(4)°, V=820(1) Å³, Z=2, space group=P−1, T=173 K, λ(Mo-K)=0.71070 Å, ρ_calc=1.718567 g cm⁻³, μ=17.44 cm⁻¹, R=0.088, R_w=0.148. An interesting two-dimensional network is assembled via hydrogen bonds through coordinated and free water molecules. The d–d transition energy levels of Co(II) ion are determined by UV–vis spectroscopy and calculated by ligand field theory. The calculated results agree well with experiment ones.     

Ribosome kinetics and aa-tRNA competition determine rate and fidelity of peptide synthesis

It is generally accepted that the translation rate depends on the availability of cognate aa-tRNAs. In this study it is shown that the key factor that determines translation rate is the competition between near-cognate and cognate aa-tRNAs. The transport mechanism in the cytoplasm is diffusion, thus the competition between cognate, near-cognate and non-cognate aa-tRNAs to bind to the ribosome is a stochastic process. Two competition measures are introduced; C(i) and R(i) (i = 1, 64) are quotients of the arrival frequencies of near-cognates vs. cognates and non-cognates vs. cognates, respectively. Furthermore, the reaction rates of bound cognates differ from those of bound near-cognates. If a near-cognate aa-tRNA binds to the A site of the ribosome, it may be rejected at the anti-codon recognition step or proofreading step or it may be accepted. Regardless of its fate, the near-cognates and non-cognates have caused delays of varying duration to the observed rate of translation. Rate constants have been measured at a temperature of 20 °C by (Gromadski, K.B., Rodnina, M.V., 2004. Kinetic determinants of high-fidelity tRNA discrimination on the ribosome. Mol. Cell 13, 191–200). These rate constants have been re-evaluated at 37 °C, using experimental data at 24.5 °C and 37 °C (Varenne, S., et al., 1984. Translation in a non-uniform process: effect of tRNA availability on the rate of elongation of nascent polypeptide chains. J. Mol. Biol. 180, 549–576). The key results of the study are: (i) the average time (at 37 °C) to add an amino acid, as defined by the ith codon, to the nascent peptide chain is: τ(i) = 9.06 + 1.445 × [10.48C(i) + 0.5R(i)] (in ms); (ii) the misreading frequency is directly proportional to the near-cognate competition, E(i) = 0.0009C(i); (iii) the competition from near-cognates, and not the availability of cognate aa-tRNAs, is the most important factor that determines the translation rate – the four codons with highest near-cognate competition (in the case of E. coli) are [GCC] > [CGG] > [AGG] > [GGA], which overlap only partially with the rarest codons: [AGG] < [CCA] < [GCC] < [CAC]; (iv) based on the kinetic rates at 37 °C, the average time to insert a cognate amino acid is 9.06 ms and the average delay to process a near-cognate aa-tRNA is 10.45 ms and (vii) the model also provides estimates of the vacancy times of the A site of the ribosome – an important factor in frameshifting.     

Extraction of Pb(II), Cd(II), and Hg(II) from aqueous solution by nitrogen and thiol functionality grafted to silica gel measured by calorimetry

The reaction of ethylene sulfide with 3-aminopropyltrimethoxysilane gave a new silylating agent, which was anchored onto a silica surface via the sol–gel procedure. This surface displayed a chelating moiety containing nitrogen and two sulfur basic centers potentially capable of extracting cations from aqueous solutions. The process of metal extraction was followed by a batch method, and fitted to a modified Langmuir equation. The maximum adsorption capacities found were: 2.06 ± 0.01, 3.72 ± 0.02, and 5.14 ± 0.02 mmol g⁻¹ for Pb(II), Cd(II), and Hg(II), respectively. The enthalpies of bending are: −1.16 ± 0.04, −3.60 ± 0.10, and −8.94 ± 0.03 kJ mol⁻¹ for Cd(II), Pb(II), and Hg(II), respectively. The Gibbs free energies of binding agree with the spontaneity of the proposed reactions between cations and basic centers.     

Hydrogenmaleato bridged supramolecular double chains via π–π stacking interactions: syntheses, crystal structures and magnetic properties of ∞[Cu(phen)X(HL)2/2] with X=Cl (1), NO3 (2) and H2L=maleic acid

Two novel hydrogen maleato (HL) bridged Cu(II) complexes _∞¹[Cu(phen)Cl(HL)_2/2] 1 and _∞¹[Cu(phen)(NO₃)(HL)_2/2] 2 were obtained from reactions of 1,10-phenanthroline, maleic acid with CuCl₂·2H₂O and Cu(NO₃)₂·3H₂O, respectively, in CH₃OH/H₂O (1:1 v/v) at pH=2.0 and the crystal structures were determined by single crystal X-ray diffraction methods. Both complexes crystallize isostructurally in the monoclinic space group P2₁/n with cell dimensions: 1 a=8.639(2) Å, b=15.614(3) Å, c=11.326(2) Å, β=94.67(3)°, Z=4, D_calc=1.720 g/cm³ and 2 a=8.544(1) Å, b=15.517(2) Å, c=12.160(1) Å, β=90.84(8)°, Z=4, D_calc=1.734 g/cm³. In both complexes, the square pyramidally coordinated Cu atoms are bridged by hydrogen maleato ligands into 1D chains with the coordinating phen ligands parallel on one side. Interdigitation of the chelating phen ligands of two neighbouring chains via π–π stacking interactions forms supramolecular double chains, which are then arranged in the crystal structures according to pseudo 1D close packing patterns. Both complexes exhibit similar paramagnetic behavior obeying Curie–Weiss laws χ_m(T−θ)=0.414 cm³ mol⁻¹ K with the Weiss constants θ=−1.45, −1.0 K for 1 and 2, respectively.     

Structures of 3,3′-dicarbometoxy-2,2′-bipyridine complexes with silver(I) and copper(II) cations

The structures of 3,3′-dicarbometoxy-2,2′-bipyridine (dcmbpy) complexes with copper(II) and silver(I) cations have been determined using single crystal X-ray-diffraction. The crystals of Cu(dcmbpy)Cl₂ are monoclinic, C2/c, a = 16.966(3), b = 18.373(3), c = 13.154(2) Å, β = 126.543(3)°. The crystals of Ag(dcmbpy)NO₃ · H₂O are also monoclinic, C2/c, a = 16.7547(13), b = 11.0922(9), c = 18.7789(18) Å, β = 100.228(7)°. The results have been compared with the literature data on the complexes of dcmbpy and its precursors: 2,2′-bipyridine (bpy) and 3,3′-dicarboxy-2,2′-bipyridine (dcbpy). Two types of complexes of 3,3′-carboxy derivatives of bpy are distinguished: (1) with metal atom bonded to two N atoms of the same molecule and (2) with metal atom bonded to two N atoms of two different molecules. The Cu(dcmbpy)Cl₂ complex belongs to the first type, whereas Ag(dcmbpy)NO₃ · H₂O belongs to the second type.     

Structure and conformational properties of carbonylbisimidosulfuryl fluoride, O=C(N=S(O)F2)2

The molecular structure and conformational properties of O=C(N=S(O)F₂)₂ (carbonylbisimidosulfuryl fluoride) were determined by gas electron diffraction (GED) and quantumchemical calculations (HF/3-21G* and B3LYP/6-31G*). The analysis of the GED intensities resulted in a mixture of 76(12)% syn–syn and 24(12)% syn–anti conformer (ΔH⁰=H⁰(syn–anti)−H⁰(syn–syn)=1.11(32) kcal mol⁻¹) which is in agreement with the interpretation of the IR spectra (68(5)% syn–syn and 32(5)% syn–anti, ΔH⁰=0.87(11) kcal mol⁻¹). syn and anti describe the orientation of the S=N bonds relative to the C=O bond. In both conformers the S=O bonds of the two N=S(O)F₂ groups are trans to the C–N bonds. According to the theoretical calculations, structures with cis orientation of an S=O bond with respect to a C–N bond do not correspond to minima on the energy hyperface. The HF/3-21G* approximation predicts preference of the syn–anti structure (ΔE=−0.11 kcal mol⁻¹) and the B3LYP/6-31G* method results in an energy difference (ΔE=1.85 kcal mol⁻¹) which is slightly larger than the experimental values. The following geometric parameters for the O=C(N=S)₂ skeleton were derived (r_a values with 3σ uncertainties): C=O 1.193 (9) Å, C–N 1.365 (9) Å, S=N 1.466 (5) Å, O=C–N 125.1 (6)° and C–N=S 125.3 (10)°. The geometric parameters are reproduced satisfactorily by the HF/3-21G* approximation, except for the C–N=S angle which is too large by ca. 6°. The B3LYP method predicts all bonds to be too long by 0.02–0.05 Å and the C–N=S angle to be too small by ca. 4°.     

Structure analysis and the standard molar enthalpy of formation of a coordination polymer [Co(TO)2Cl2]n (TO = 1,2,4-triazole-5-one)

A coordination polymer was synthesized by the reaction of CoCl₂ with 1,2,4-triazole-5-one (TO) and charaterized by means of IR and TG–DTG. Single-crystal structure analysis showed that the complex crystallized in the monoclinic space group C2/c: a = 23.105(9) Å, b = 3.5683(2) Å, c = 13.589(6) Å,  = 90°, β = 124.038(4)°, γ = 90°, V = 928.4(7) Å³, Z = 4. The standard molar enthalpy of formation of the complex was determined to be (−1034.28 ± 0.95) kJ mol⁻¹.