Polybenzimidazoles tethered with N‐phenyl 1,2,4‐triazole units as polymer electrolytes for fuel cells

Polybenzimidazole (PBI) polymers tethered with N‐phenyl 1,2,4‐triazole (NPT) groups were prepared from a newly synthesized aromatic diacid, 3′‐(4‐phenyl‐4H‐1,2,4‐triazole‐3,5‐diyl) dibenzoic acid (PTDBA). The obtained polymers show superior thermal and chemical stability and good solubility in many aprotic solvents. The inherent viscosities of all polymers were around 1 dL/g. They exhibit high thermal stability with initial decomposition temperature ranging from 515 to 530 °C, high glass transition temperature ranging from 375 to 410 °C, and good mechanical properties with tensile stress in the range of 66–98 MPa and modulus 1897–2600 MPa. XRD analysis indicates that these polymers are amorphous in nature. Physicochemical properties such as water and phosphoric acid‐uptake, oxidative stability, and proton conductivity of membranes of these polymers have also been determined. The proton conductivity ranged from 4.7 × 10^?3 to 1.8 × 10^?2 S cm^?1 at 175 °C in dry conditions. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2289–2303, 2009     

Polymer electrolyte membranes based on p‐toluenesulfonic acid doped poly(1‐vinyl‐1,2,4‐triazole): Synthesis,thermal and proton conductivity properties

Throughout this work, the synthesis, thermal as well as proton conducting properties of acid doped heterocyclic polymer were studied under anhydrous conditions. In this context, poly(1‐vinyl‐1,2,4‐triazole), PVTri was produced by free radical polymerization of 1‐vinyl‐1,2,4‐triazole with a high yield. The structure of the homopolymer was proved by FTIR and solid state ¹³C CP‐MAS NMR spectroscopy. The polymer was doped with p‐toluenesulfonic acid at various molar ratios, x = 0.5, 1, 1.5, 2, with respect to polymer repeating unit. The proton transfer from p‐toluenesulfonic acid to the triazole rings was proved with FTIR spectroscopy. Thermogravimetry analysis showed that the samples are thermally stable up to ～250 °C. Differential scanning calorimetry results illustrated that the materials are homogeneous and the dopant strongly affects the glass transition temperature of the host polymer. Cyclic voltammetry results showed that the electrochemical stability domain extends over 3 V. The proton conductivity of these materials increased with dopant concentration and the temperature. Charge transport relaxation times were derived via complex electrical modulus formalism (M*). The temperature dependence of conductivity relaxation times showed that the proton conductivity occurs via structure diffusion. In the anhydrous state, the proton conductivity of PVTri1PTSA and PVTri2PTSA was measured as 8 × 10^?4 S/cm at 150 °C and 0.012 S/cm at 110 °C, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 1016–1021, 2010     

Synthesis and properties of a new fluorine‐containing polybenzimidazole for high‐temperature fuel‐cell applications

An amorphous, organosoluble, fluorine‐containing polybenzimidazole (PBI) was synthesized from 3,3′‐diaminobenzidine and 2,2‐bis(4‐carboxyphenyl)hexafluoropropane. The polymer was soluble in N‐methylpyrrolidinone and dimethylacetamide and had an inherent viscosity of 2.5 dL/g measured in dimethylacetamide at a concentration of 0.5 g/dL. The 5% weight loss temperature of the polymer was 520 °C. Proton‐conducting PBI membranes were prepared via solution casting and doped with different amounts of phosphoric acid. In the methanol permeability measurement, the PBI membranes showed much better methanol barrier ability than a Nafion membrane. The proton conductivity of the acid‐doped PBI membranes increased with increasing temperatures and concentrations of phosphoric acid in the polymer. The PBI membranes showed higher proton conductivity than a Nafion 117 membrane at high temperatures. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 4508–4513, 2006     

Novel anhydrous proton conducting copolymers of 1‐vinyl‐1,2,4‐triazole and diisopropyl‐p‐vinylbenzyl phosphonate

Phosphonic acid functional polymers are currently of interest because of their high proton conductivity in humidified and anhydrous systems. In addition, heterocyclic compounds are used in anhydrous proton conducting polymer membranes. In that study, a new copolymer based on 1‐vinyl‐1,2,4‐triazole (VTri) and diisopropyl‐p‐vinylbenzyl phosphonate (VBP) was synthesized, and their thermal, chemical, and proton conducting properties were investigated. The copolymers were synthesized by free radical copolymerization of the corresponding monomers at several monomer feed ratios to obtain P(VTri‐co‐VBP) copolymers. The copolymer samples were then hydrolyzed to produce poly(vinyl triazole‐co‐vinyl phosphonic acid) copolymers. The composition of the copolymers was determined by elemental analysis. The copolymerization and hydrolysis reactions were verified by Fourier transform infrared spectroscopy and ion exchange capacity measurements. Thermogravimetry analysis indicates that the copolymers are thermally stable up to 300°C. In order to increase the proton conductivity, the copolymers were doped with H₃PO₄ at several stoichometric ratios. The proton conductivity increases with triazole and phosphoric acid content. In the absence of humidity, the copolymer electrolyte, P(VTri‐co‐VBPA)1:0.5 X = 2, showed a proton conductivity of 0.005 S/cm at 150°C. Copyright © 2013 John Wiley & Sons, Ltd.     

Investigation of proton conductivity of anhydrous proton exchange membranes prepared via grafting vinyltriazole onto alkaline‐treated PVDF

This work uses a simple “grafting through” approach in the preparation of anhydrous poly(vinylidene fluoride) (PVDF)‐g‐PVTri polymer electrolyte membranes (PEMs). Alkaline‐treated PVDF was used as a macromolecule in conjunction with vinyltriazole in the graft copolymerization. The obtained polymer was subsequently doped with triflic acid (TA) at different stoichiometric ratios with respect to triazole units and the anhydrous PEMs (PVDF‐g‐PVTri‐(TA)_x) were prepared. All samples were characterized by FTIR and ¹H NMR. The composition of PVDF‐g‐PVTri was determined by energy dispersive spectroscopy. Thermal properties of the membranes were examined by thermogravimetric analysis and differential scanning calorimetry. The surface roughness and morphology of the membranes were studied using atomic force microscopy, X‐ray diffraction, and scanning electron microscopy. PVDF‐g‐PVTri‐(TA)₃ (C3‐TA₃) with a degree of grafting of 47.22% showed a maximum proton conductivity of 0.09 S cm^?1 at 150 °C and anhydrous conditions. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1885–1897     

Synthesis and characterization of fluorine‐containing polybenzimidazole for proton conducting membranes in fuel cells

Two new kinds of fluorine‐containing polybenzimidazoles (PBI), poly(2,2′‐(tetrafluoro‐p‐phenylene)‐5,5′‐bibenzimidazole) and poly(2,2′‐tetradecafluoroheptylene‐5,5′‐bibenzimidazole), were synthesized by condensation polymerization of 3,3′‐diaminobenzidine and perfluoroterephthalic acid (or perfluoroazelaic acid), with polyphosphoric acid as solvent. Thermogravimetric analysis results show that the fluorine‐containing polymers synthesized exhibit promising thermal stability. The film‐forming properties of the fluorine‐containing polymers are improved over nonfluorinated PBI. The introduction of fluorine into the backbone of the polymers has significant positive affection on their chemical oxidation stability demonstrated by Fenton test. Compared with poly(2,2′‐(m‐phenylene)‐5,5′‐bibenzimidazole)/phosphoric acid (PA) composite membrane, the resulting fluorinated membranes with a same PA doping level exhibit better flexibility and higher proton conductivity. The maximum proton conductivity gained is 3.05 × 10^?2 S/cm at 150 °C with a PA doping level of 7. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 2115–2122, 2010     

Proton‐conducting polymers based on benzimidazoles and sulfonated benzimidazoles

A sulfonated derivative of polybenzimidazole is reported, and its properties are analyzed in comparison with related polybenzimidazole proton‐conducting materials. Poly(2,5‐benzimidazole), poly(m‐phenylenebenzobisimidazole), and poly[m‐(5‐sulfo)‐phenylenebenzobisimidazole] were prepared by condensation of the corresponding monomers in polyphosphoric acid. Several adducts of these polymers with phosphoric acid were prepared. The resulting materials were characterized by chemical analysis, Fourier transform infrared spectroscopy, and thermogravimetric analysis; also, the dc conductivity of doped and undoped derivatives was measured. Similar to what has been observed for the commercial polybenzimidazole polymer (also examined here for comparison), the title polymers exhibit high thermal stability. Furthermore, their doping with phosphoric acid leads to a significant increase in conductivity from less than 10^?11 Scm^?1 for the undoped polymers to 10^?4 Scm^?1 (both at room temperature) for their acid‐loaded derivatives. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3703–3710, 2002     

Energy material - the role of silicotungstic acid and fly ash in sulfonated poly (ether sulfone) composites for PEMFC applications

The composite polymer electrolyte membranes were prepared from sulfonated poly (ether sulfone) (SPES), silicotungstic acid (STA) and fly ash (FA). Post sulfonation process was adopted to synthesize SPES using sulphuric and chlorosulfonic acid. The prepared electrolyte membranes were examined by water uptake capacity, swelling ratio, ion-exchange ability, proton conductivity, thermal stability and electrochemical performance for evaluating the pertinence of these membranes in fuel cell applications. As such the pristine membrane restricts with the proton conductivity of 0.042?S cm^?1 at 30?°C and 0.060?S cm^?1 at 90?°C while the polymer composite membrane, SP-STA-FA-10 reveals the maximum conductivity of 0.054?S cm^?1 at 30?°C and 0.073?S cm^?1 at 90?°C. It also exhibits good thermal stability than that of the pure membrane. The membrane electrode assemblies (MEAs) have been successfully developed from SPES as well as SP-STA-FA-10 membranes and their electrochemical performance were studied the wide range of current density. Herein, the composite membranes derived from SPES, STA and FA can be viable candidates for fuel cell applications.     

Effects of different acid functional groups on proton conductivity of polymer‐1,2,4‐triazole blends

Proton transfer reactions under anhydrous conditions have attracted remarkable interest due to chemical energy conversions in polymer electrolyte membrane fuel cells. In this work, 1H‐1,2,4‐triazole (Tri) was used as a proton solvent in different polymer host matrices such as Poly(vinylphosphonic acid) (PVPA), and poly(2‐acrylamido‐2‐methyl‐1‐propane sulfonic acid) (PAMPS). PVPATri_x and PAMPSTri_x electrolytes were investigated where x is the molar ratio of Tri to corresponding polymer repeat unit. The interaction between polymer and Tri was studied via FTIR spectroscopy. Thermogravimetry analysis and differential scanning calorimetry were employed to examine the thermal stability and homogeneity of the materials, respectively. PVPATri_1.5 showed a maximum water‐free proton conductivity of 2.3 × 10^?3 S/cm at 120 °C and that of PAMPSTri₂ was 9.3 × 10^?4 S/cm at 140 °C. The results were interpreted in terms of different acidic functional groups and composition. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 3315–3322, 2006     

The effect of structural variations on aromatic polyethers for high‐temperature PEM fuel cells

Three series of new aromatic polyether sulfones bearing phenyl, p‐tolyl or carboxyl side groups, respectively, and polar pyridine main chain groups were developed. Most of the polymeric materials presented high molecular weights and excellent solubility in common organic solvents. More importantly, they formed stable, self‐standing membranes that were thoroughly characterized in respect to their thermal, mechanical and oxidative stability, their phosphoric acid doping ability and ionic conductivity. Particularly, the copolymers bearing side p‐tolyl or carboxyl groups fulfill all necessary requirements for application as proton electrolyte membranes in high temperature fuel cells, which are glass transition temperatures higher than 220 °C, thermal stability up to 400 °C, oxidative stability, high doping levels (DLs) and proton conductivities of about 0.02 S/cm. Initial single fuel cell results at high temperatures, 160 °C or 180 °C, using a copolymer bearing p‐tolyl side groups with a relatively low DLs around 200 wt % and dry H₂/Air feed gases, revealed efficient power generation with a current density of 0.5 A/cm² at 500 mV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Sulfonated silica‐based electrolyte nanocomposite membranes

New functionalized particles were prepared by attaching sulfonated aromatic bishydroxy compounds onto fumed silica surface. First, a bromophenyl group was introduced onto the silica surface by reaction of bromophenyltrimethoxysilane with fumed silica. Then, sulfonated bishydroxy aromatic compounds were chemically attached to the silica surface by nucleophilic substitution reactions. The structure of the modified silica was characterized by elemental analysis: ¹³C‐NMR, ²⁹Si‐NMR, and FTIR. Afterward, novel inorganic–organic electrolyte composite membranes based on sulfonated poly(ether ether ketone) have been developed using the sulfonated aromatic bishydroxy compounds chemically attached onto the fumed silica surface. The composite membrane prepared using silica with sulfonated hydroxytelechelic, containing 1,3,4‐oxadiazole units, has higher proton conductivity values in all range of temperatures (40–140 °C) than the membrane containing only the plain electrolyte polymer, while the methanol permeability determined by pervaporation experiment was unchanged. A proton conductivity up to 59 mS cm^?1 at 140 °C was obtained. The combination of these effects may lead to significant improvement in fuel cells (fed with hydrogen or methanol) at temperatures above 100 °C. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2278–2298, 2006     

Poly(tetrafluorostyrenephosphonic acid)–polysulfone block copolymers and membranes

A series of ionic ABA triblock copolymers having a central polysulfone (PSU) block and poly(2,3,5,6,‐tetrafluorostyrene‐4‐phosphonic acid) (PTFSPA) outer blocks with different lengths were prepared and studied as electrolyte membranes. PSU with terminal benzyl bromide was used as a bifunctional macroinitiator for the formation of poly(2,3,4,5,6‐pentafluorostyrene) (PPFS) blocks by atom transfer radical polymerization. Selective and complete phosphonation of the PPFS blocks was achieved via a Michaelis?Arbuzov reaction using tris(trimethylsilyl)phosphite at 170 °C. Copolymer films were cast from solution and subsequently fully hydrolyzed to produce transparent flexible proton conducting PTFSPA‐b‐PSU‐b‐PTFSPA membranes with a thermal stability reaching above 270 °C under air, and increasing with the PTFSPA content. Studies of thin copolymer electrolyte membranes by tapping mode atomic force microscopy showed phase separated morphologies with continuous proton conducting PTFSPA nano scale domains. Block copolymer membranes reached a proton conductivity of 0.08 S cm^?1 at 120 °C under fully hydrated conditions, and 0.8 mS cm^?1 under 50% relative humidity at 80 °C. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4657–4666     

Preparation and characterization of layer‐by‐layer self‐assembly membrane based on sulfonated polyetheretherketone and polyurethane for high‐temperature proton exchange membrane

A concept of preparing high‐temperature proton exchange membranes with layer‐by‐layer (LBL) self‐assembly technique was proposed and the sulfonated polyetheretherketone (SPEEK) and polyurethane (PU) with 200 LBL deposition cycles denoting (SPEEK/PU)₂₀₀ membrane was prepared in this research. Owing to the strong electrostatic interaction between ? group in SPEEK and ? C? N⁺ group in PU, (SPEEK/PU)₂₀₀ membrane with LBL self‐assembly structure showed a favorable structural stability. The phosphoric acid (PA)‐doped (SPEEK/PU)₂₀₀ membrane showed a higher proton conductivity relative to PA doped SPEEK/PU membrane by solution casting method (SPEEK/PU)₂₀₀/40%PA membrane possessed a proton conductivity value of 2.90 × 10^?2 S/cm at 150 °C under anhydrous conditions. The LBL self‐assembly structure provided a possibility to reduce the negative effect from polymer skeleton blocking charge carrier species even immobilizing protons. Moreover, the (SPEEK/PU)₂₀₀ membrane presented the particularly noteworthy mechanical property even with PA doping. The tensile stress values at break were 72.8 and 24.1 MPa, respectively, for (SPEEK/PU)₂₀₀ and (SPEEK/PU)₂₀₀/40%PA membrane at room temperature, which were obviously higher than the reported values of 15.9 and 2.81 MPa for SPEEK/PU and SPEEK/PU/60%PA membrane. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55 , 3446–3454     

Preparation and characterization of polybenzimidazole membranes prepared by gelation in phosphoric acid

Phosphoric acid doped poly (2, 2′‐(m‐phenylene)‐5, 5′‐bibenzimidazole) (PBI) membranes were prepared by dissolving PBI powders in 85% phosphoric acid at 190–200°C and then promoting gelation of the PBI by cooling the solutions to ?18°C. The extent of acid doping of the PBI membranes was controlled by immersing the membrane in aqueous phosphoric acid solutions of different concentrations (acid de‐doping). The process of the acid de‐doping was faster than acid doping of membrane cast from N,N‐dimethylacetamide (DMAc). The de‐doping process caused shrinkage of the PBI membrane and thus an increase in the membrane strength due to the packing of PBI chains according to the X‐ray diffraction analysis. The tensile stress and proton conductivity of the obtained PBI membranes with different acid doping levels were measured. For a PBI (η_IV: 0.58 dL · g^?1) membrane with an acid doping level of 7.0 (molar number of doped acid per mole repeat unit of PBI), the stress at break and proton conductivity at 120°C without humidification were 2.6 MPa and 5.1 × 10^?2 S · cm^?1, respectively. These results were comparable to those of the membranes cast from PBI solutions in DMAc. Copyright © 2009 John Wiley & Sons, Ltd.     

Studies on sulfonic acid functionalized hollow silica spheres/Nafion® composite proton exchange membranes

In this work, sulfonic acid functionalized hollow silica spheres (SAFHSS)/Nafion® composite membranes were prepared by a recasting procedure. The influences of temperature on water uptake, swelling degree, and proton conductivity of the composite membranes were studied. In comparison with the pure recast Nafion® membrane, it was found that water uptake of composite membranes increased with increasing SAFHSS loading at all temperature studied. The swelling degree of SAFHSS/Nafion® composite membranes with 10～15 wt % SAFHSS loading was lower than that of the pure recast Nafion® at all temperatures in the study. The proton conductivity of SAFHSS/Nafion® composite membranes was constantly higher than that of the pure recast Nafion® at all temperatures (50～130 °C). In a range from 50 to 130 °C, the highest conductivity of composite membranes was obtained when 10 wt % SAFHSS was loaded. The maximum conductivity reached 0.1 S cm^?1 at 100% relative humidity and 100 °C, even the temperature reached to 130 °C, the conductivity of the composite membranes with 10 wt % SAFHSS was still as high as 4.4 × 10^?2 S cm^?1 at 100% relative humidity, whereas the conductivity of the pure recast Nafion® was only 2.2 × 10^?3 S cm^?1. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2647–2655, 2009     

Synthesis and characterization of anhydrous conducting polyimide/ionic liquid complex membranes via a new route for high‐temperature fuel cells

The paper deals with the synthesis and characterization of a new series of anhydrous conducting acid‐doped complex membranes based on polyimide (PI) and ionic liquid (IL) for high‐temperature fuel cells via a new route. For this purpose, three imidazolium‐based ILs (RIm⁺BF₄^?) with different alkyl chain lengths (R=methyl, ethyl, and butyl) are added into polyamic acid (PAA) intermediate prepared from the reaction of benzophenonetetracarboxylic dianhydride and diaminodiphenylsulfone in different –COOH/imidazolium molar ratios (n = 0.5, 1, and 2). Then, the thermally imidized complex membrane was doped with H₂SO₄. The conductivities of acid‐doped PI/IL complex membranes prepared by taking n of 1 are found to be in the range of 10^?4?10^?5 S cm^?1 at 180°C, whereas the acid‐free PI/IL complex membranes show the conductivity at around 10^?9?10^?10 S cm^?1. Thermogravimetric analysis results reveal that the acid‐doped PI/IL complex membranes are thermally stable up to 250°C. Dynamic mechanical analysis results of the acid‐doped ionically interacted complex membrane show that the mechanical strengths of the PI/IL complex membranes including 1‐methyl imidazolium tetrafluoroborate (MeIm‐BF₄) and 1‐ethyl 3‐methyl imidazolium tetrafluoroborate (EtIm‐BF₄) are comparable with those of pristine PI until 200°C. Furthermore, it can be clearly emphasized that the ionic interaction between carboxylic acid groups of PAA's and IL's cations offers a positive role in long‐term conductivity stability by preventing the IL migration at high temperatures. On the other hand, preliminary methanol permeability tests of the acid‐doped membranes show that they can also be considered as an alternative for direct methanol fuel cells. Copyright © 2011 John Wiley & Sons, Ltd.     

Synthesis and properties of novel sulfonated polyimides containing binaphthyl groups as proton‐exchange membranes for fuel cells

A novel sulfonated diamine monomer, 2,2′‐bis(p‐aminophenoxy)‐1,1′‐binaphthyl‐6,6′‐disulfonic acid (BNDADS), was synthesized. A series of sulfonated polyimide copolymers containing 30–80 mol % BNDADS as a hydrophilic component were prepared. The copolymers showed excellent solubility and good film‐forming capability. Atomic force microscopy phase images clearly showed hydrophilic/hydrophobic microphase separation. The relationship between the proton conductivity and degree of sulfonation was examined. The sulfonated polyimide copolymer with 60 mol % BNDADS showed higher proton conductivity (0.0945–0.161 S/cm) at 20–80 °C in liquid water. The membranes exhibited methanol permeability from 9 × 10^?8 to 5 × 10^?7 cm²/s at 20 °C, which was much lower than that of Nafion (2 × 10^?6cm²/s). The copolymers were thermally stable up to 300 °C. The sulfonated polyimide copolymers with 30–60 mol % BNDADS showed reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 40 mol % BNDADS was 80.6 MPa under high moisture conditions. The optimum concentration of BNDADS was found to be 60 mol % from the viewpoint of proton conductivity, methanol permeability, and membrane stability. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 222–231, 2007     

Preliminary evaluation of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid composite membranes for direct methanol fuel cell applications

A series of sulfonated poly(ether ether ketone)/monoethanolamine/adipic acid (SPEEK/MEA/AA) composite membranes are prepared and investigated to assess their possibility as proton exchange membranes in direct methanol fuel cells (DMFCs). A preliminary evaluation shows that introducing MEA and AA into SPEEK matrix decreases the thermal stability of membrane. However, the degradation temperatures are still above 260 °C, satisfying the requirement for fuel cell operation. Compared with the pure SPEEK membrane, the composite membranes exhibit not only lower water uptake and swelling ratios but also better mechanical property and oxidative stability. Noticeably, the methanol diffusion coefficient of the composite membranes decrease significantly from 3.15 × 10^?6 to 0.76 × 10^?6 cm²/s with increasing MEA and AA content, accompanied by only a small sacrifice in proton conductivity. Although both the methanol diffusion coefficient and the proton conductivity of composite membranes are lower than those of pure SPEEK and Nafion® 117 membranes, their selectivity (conductivity/methanol diffusion coefficient) are higher. In addition, the composite membranes show excellent stability in aqueous methanol solution. The good thermal and chemical stability, low swelling ratio, excellent mechanical property, low methanol diffusion coefficient, and high selectivity make the use of these composite membranes in DMFCs quite attractive. © 2007 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 45: 2871–2879, 2007     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Property improvement of nanocellulose‐reinforced proton exchange nanocomposite membrane coated with tetraethyl orthosilicate

Study on proton exchange membrane (PEM) with the aim toward excellent battery performance of PEM for fuel cells has attracted increasing attention. In this work, nanocellulose (CNC) aminated by KH792 noted as NN was prepared. CNC or NN/sulfophenylated poly(ether ether ketone ketone) (sPEEKK) nanocomposite membrane (SN) or (SNN) were produced by solution mixing. SNN was further coated with tetraethyl orthosilicate (TEOS) to obtain SNNT. The properties of sPEEKK, SN, SNN, and SNNT membranes were thoroughly investigated. The proton conductivity of SN4 was 0.22 S·cm^?1 at 90 °C, while a proton conductivity of 0.30 S·cm^?1 was obtained for SNN4, and an even higher value of 0.36 S·cm^?1 at 90 °C was obtained for the TEOS‐coated SNN4 (SNN4T). Meanwhile, SNN4T showed high thermal stability, and its T_d5 was as high as 318.2 °C. Furthermore, the composite membrane coated with TEOS also presented excellent oxidative stability. The mass of SNN2T after treated in Fenton agent for 1 h at 80 °C was still retained 96.2%, and it was not fully dissolved until 11 h. It was illustrated that aminated CNC/sPEEKK nanocomposite membranes coated with TEOS is a kind of promising materials as PEMs for fuel cells. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 2190–2200