Enhancement of photoluminescence intensity from Si nanodots using Al2O3 surface passivation layer grown by atomic layer deposition

Temperature-dependent photoluminescence (PL) from Si nanodots with Al₂O₃ surface passivation layers was studied. The Si nanodots were grown by low pressure chemical vapor deposition and the Al₂O₃ thin films were prepared by atomic layer deposition (ALD), respectively. The BOE (Buffer-Oxide-Etch) treatment resulted in the damaged surface of Si nanodots and thus caused dramatic reduction in the PL intensity. Significant enhancement of the PL intensity from Si nanodots after the deposition of Al₂O₃ thin films was observed over a wide temperature range, indicating the remarkable surface passivation effect to suppress the non-radiative recombination at the surface of Si nanodots. The results demonstrated that the Al₂O₃ surface passivation layers grown by ALD are effectually applicable to nanostructured silicon devices.     

Silicon surface passivation by atomic‐layer‐deposited Al2O3 facilitated in situ by the combination of H2O and O3 as reactants

We investigate the effect of O₃ and H₂O oxidant pre‐pulse prior to Al₂O₃ atomic layer deposition for Si surface passivation. Interfacial oxide SiO_x formed by the O₃ pre‐pulse is more beneficial than that by H₂O to a high level of surface passivation. The passivation of thinner H₂O–Al₂O₃ films is more improved by this O₃ pre‐pulse. O₃ pre‐pulse for 10 nm H₂O–Al₂O₃ reduces saturation current density in boron emitter to 18 fA cm^–2 by a factor of 1.7. Capacitance–voltage measurements reveal this interfacial oxide plays a role of decreasing interface trap density without detrimental effect to negative charge density of Al₂O₃. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

On the observation of electron–hole liquid luminescence under low excitation in Al2O3‐passivated c‐Si wafers

We report on low‐temperature photoluminescence (PL) from aluminum oxide (Al₂O₃)‐passivated c‐Si wafers, which surprisingly exhibits clear signature of the formation of the so‐called electron–hole liquid (EHL), despite the use of excitation powers for which the condensed phase is not usually observed in bulk Si. The elevated incident photon densities achieved with our micro‐PL setup together with the relatively long exciton lifetimes associated with a good quality, indirect band‐gap semiconductor such as our float‐zone c‐Si, are considered the key aspects promoting photogenerated carrier densities above threshold. Interestingly, we observe a good correlation between the intensity of the EHL feature in PL spectra and the passivation performance of the Al₂O₃ layer annealed at different temperatures. The change in the extension of the sub‐surface space‐charge region that results from the balance between the induced fixed charge in the Al₂O₃ and the defect states at the alumina/Si interface is at the origin of the observed correlation. (© 2014 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Surface passivation of phosphorus‐diffused n+‐type emitters by plasma‐assisted atomic‐layer deposited Al2O3

In recent years Al₂O₃ has received tremendous interest in the photovoltaic community for the application as surface passivation layer for crystalline silicon. Especially p‐type c‐Si surfaces are very effectively passivated by Al₂O₃, including p‐type emitters, due to the high fixed negative charge in the Al₂O₃ film. In this Letter we show that Al₂O₃ prepared by plasma‐assisted atomic layer deposition (ALD) can actually provide a good level of surface passivation for highly doped n‐type emitters in the range of 10–100 Ω/sq with implied‐V_oc values up to 680 mV. For n‐type emitters in the range of 100–200 Ω/sq the implied‐V_oc drops to a value of 600 mV for a 200 Ω/sq emitter, indicating a decreased level of surface passivation. For even lighter doped n‐type surfaces the passivation quality increases again to implied‐V_oc values well above 700 mV. Hence, the results presented here indicate that within a certain doping range, highly doped n‐ and p‐type surfaces can be passivated simultaneously by Al₂O₃. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effective silicon surface passivation by atomic layer deposited Al2O3/TiO2 stacks

In this work atomic layer deposition of Al₂O₃ and TiO₂ has been used to obtain dielectric stacks for passivation of silicon surfaces. Our experiments on n‐ and p‐type silicon wafers deposited by thin Al₂O₃/TiO₂ stacks show that a considerably improved passivation is obtained compared to the Al₂O₃ single layer. For Al₂O₃ films thinner than 20 nm the emitter saturation current density decreases with increasing TiO₂ thickness. Especially the passivation of ultrathin (～5 nm) Al₂O₃ is very effectively enhanced by TiO₂ due to a decreased interface defect density as well as an increased fixed negative charge in the stacks. Hence, the thin Al₂O₃/TiO₂ stacks developed in this work can be used as a passivation coating for Si‐based solar cells. (© 2014 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Excellent Si surface passivation by low temperature SiO2 using an ultrathin Al2O3 capping film

It is demonstrated that the application of an ultrathin aluminum oxide (Al₂O₃) capping film can improve the level of silicon surface passivation obtained by low‐temperature synthesized SiO₂ profoundly. For such stacks, a very high level of surface passivation was achieved after annealing, with S_eff < 2 cm/s for 3.5 Ω cm n‐type c‐Si. This can be attributed primarily to a low interface defect density (D_it < 10¹¹ eV^–1 cm^–2). Consequently, the Al₂O₃ capping layer induced a high level of chemical passivation at the Si/SiO₂ interface. Moreover, the stacks showed an exceptional stability during high‐temperature firing processes and therefore provide a low temperature (≤400 °C) alternative to thermally‐grown SiO₂. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Effective surface passivation of crystalline silicon using ultrathin Al2O3 films and Al2O3/SiNx stacks

We measure surface recombination velocities (SRVs) below 10 cm/s on p‐type crystalline silicon wafers passivated by atomic–layer–deposited (ALD) aluminium oxide (Al₂O₃) films of thickness ≥10 nm. For films thinner than 10 nm the SRV increases with decreasing Al₂O₃ thickness. For ultrathin Al₂O₃ layers of 3.6 nm we still attain a SRV < 22 cm/s on 1.5 Ω cm p‐Si and an exceptionally low SRV of 1.8 cm/s on high‐resistivity (200 Ω cm) p‐Si. Ultrathin Al₂O₃ films are particularly relevant for the implementation into solar cells, as the deposition rate of the ALD process is extremely low compared to the frequently used plasma‐enhanced chemical vapour deposition of silicon nitride (SiN_x). Our experiments on silicon wafers passivated with stacks composed of ultrathin Al₂O₃ and SiN_x show that a substantially improved thermal stability during high‐temperature firing at 830 °C is obtained for the Al₂O₃/SiN_x stacks compared to the single‐layer Al₂O₃ passivation. Al₂O₃/SiN_x stacks are hence ideally suited for the implementation into industrial‐type silicon solar cells where the metal contacts are made by screen‐printing and high‐temperature firing of metal pastes. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Structure of Al2O3 thin layers synthesized on the silicon surface by atomic layer deposition

The distribution of the phase and chemical composition at an Al₂O₃/Si interface is studied by depth-resolved ultrasoft x-ray emission spectroscopy. The interface is formed by atomic layer deposition of Al₂O₃ films of various thicknesses (from several to several nanometers to several hundreds of nanometers) on the Si(100) surface (c-Si) or on a 50-nm-thick SiO₂ buffer layer on Si. L _2,3 bands of Al and Si are used for analysis. It is found that the properties of coatings and Al₂O₃/Si interfaces substantially depend on the thickness of the Al₂O₃ layer, which is explained by the complicated character of the process kinetics. At a small thickness of coatings (up to 10–30 nm), the Al₂O₃ layer contains inclusions of oxidized Si atoms, whose concentration increases as the interface is approached. As the thickness increases, a layer containing inclusions of metallic Al clusters forms. A thin interlayer of Si atoms occurring in an unconventional chemical state is found. When the SiO₂ buffer layer is used (Al₂O₃/SiO₂/Si), the structure of the interface and the coating becomes more perfect. The Al₂O₃ layer does not contain inclusions of metallic aluminum, does not vary with the sample thickness, and has a distinguished boundary with silicon.     

Preparation and characterization of ferroelectric SrBi2Ta2O9 thin films on Si using Al2O3 buffer layers

SrBi₂Ta₂O₉ (SBT) thin films were prepared on p-type Si(100) substrates with Al₂O₃ buffer layers. Both the SBT films and the Al₂O₃ buffer layers were deposited by a pulsed laser deposition technique using a KrF excimer laser. An Al prelayer was used to prevent Si surface oxidization in the initial growth stage. It is shown that Al₂O₃ buffer layers effectively prevented interdiffusion between SBT and Si substrates. Furthermore, the capacitance–voltage (C-V) characteristics of the SBT/Al₂O₃/Si heterostructures show a hysteresis loop with a clockwise trace, demonstrating the ferroelectric switching properties of SBT films and showing a memory window of 1.6 V at 1 MHz. Received: 17 July 2000 / Accepted: 16 August 2000 / Published online: 30 November 2000     

Passivation of black silicon boron emitters with atomic layer deposited aluminum oxide

The nanostructured surface – also called black silicon (b‐Si) – is a promising texture for solar cells because of its extremely low reflectance combined with low surface recombination obtained with atomic layer deposited (ALD) thin films. However, the challenges in keeping the excellent optical properties and passivation in further processing have not been addressed before. Here we study especially the applicability of the ALD passivation on highly boron doped emitters that is present in crystalline silicon solar cells. The results show that the nanostructured boron emitters can be passivated efficiently using ALD Al₂O₃ reaching emitter saturation current densities as low as 51 fA/cm². Furthermore, reflectance values less than 0.5% after processing show that the different process steps are not detrimental for the low reflectance of b‐Si. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Al2O3 thin films by plasma-enhanced chemical vapour deposition using trimethyl-amine alane (TMAA) as the Al precursor

2 O₃ thin films by plasma-enhanced chemical vapour deposition (PECVD) using trimethyl-amine alane (TMAA) as the Al precursor. The thin films were deposited on both Si and quartz silica (SiO₂) substrates. Deposition rates were typically 60 Å min^-1 keeping the TMAA temperature constant at 45 °C. The deposited Al₂O₃ thin films were stoichiometric alumina with low carbon contamination (0.7–1.3 At%). The refractive index ranged from 1.54 to 1.62 depending on the deposition conditions. The deposition rate was studied as a function of both the RF power and the substrate temperature. The structure and the surface of the deposited Al₂O₃ thin films were studied using X-ray diffraction, atomic force microscopy (AFM) and scanning electron microscopy (SEM). Received: 20 May 1997/Accepted: 12 June 1997     

Investigation of interface characteristics of Al2O3/Si under various O2 plasma exposure times during the deposition of Al2O3 by PA-ALD

Plasma-assisted atomic layer deposition (PA-ALD) is more suitable than thermal atomic layer deposition (ALD) for mass production because of its faster growth rate. However, controlling surface damage caused by plasma during the PA-ALD process is a key issue. In this study, the passivation characteristics of Al₂O₃ layers deposited by PA-ALD were investigated with various O₂ plasma exposure times. The growth per cycle (GPC) during Al₂O₃ deposition was saturated at approximately 1.4?Å/cycle after an O₂ plasma exposure time of 1.5?s, and a refractive index of Al₂O₃ in the range of 1.65–1.67 was obtained. As the O₂ plasma exposure time increased in the Al₂O₃ deposition process, the passivation properties tended to deteriorate, and as the radio frequency (RF) power increased, the passivation uniformity and the thermal stability of the Al₂O₃ layer deteriorated. To study the Al₂O₃/Si interface characteristics, the capacitance-voltage (C-V) and the conductance-voltage (G-V) were measured using a mercury probe, and the fixed charge density (Q_f) and the interface trap density (D_it) were then extracted. The Q_f of the Al₂O₃ layer deposited on a Si wafer by PA-ALD was almost unaffected, but the D_it increased with O₂ plasma exposure time. In conclusion, as the O₂ plasma exposure time increased during Al₂O₃ layer deposition by PA-ALD, the Al₂O₃/Si interface characteristics deteriorated because of plasma surface damage.     

Fluorination of Al2O3 blocking layer for improving the performance of metal‐oxide‐nitride‐oxide‐silicon flash memory

The characteristics of Al₂O₃ film grown by atomic‐layer deposition as blocking layer with and without fluorine plasma treatment were investigated based on a capacitor structure of Al/Al₂O₃/TaON/SiO₂/Si. The physical structure was studied by transmission electron microscopy, and the chemical composition of the blocking layer was analyzed by X‐ray photoelectron spectroscopy and secondary ion mass spectroscopy. Moreover, the surface roughness of the blocking layer was investigated by atomic force microscopy. Compared with a capacitor with Al₂O₃ blocking layer, the one with fluorinated Al₂O₃ displayed higher programming/erasing speeds, better endurance property and better charge retention characteristic because the fluorination could reduce excess oxygen and traps in the blocking layer, thus forming a larger barrier height at the interface between the charge‐trapping layer and the blocking layer. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Al2O3钝化及其在晶硅太阳电池中的应用

介绍了Al₂O₃的材料性质及其原子层沉积制备方法, 详细阐述了该材料的钝化机制(化学钝化和场效应钝化), 并从薄膜厚度、热稳定性及叠层钝化等角度阐释其优化方案. 概述了Al₂O₃钝化在晶体硅太阳电池中的应用, 主要包括钝化发射极及背面局部扩散电池和钝化发射极及背表面电池. 最后, 对Al₂O₃钝化工艺的未来研究方向和大规模的工业应用进行了展望.     

Mechanism for crystalline Si surface passivation by the combination of SiO2 tunnel oxide and µc‐SiC:H thin film

This work demonstrates that the combination of a wet‐chemically grown SiO₂ tunnel oxide with a highly‐doped microcrystalline silicon carbide layer grown by hot‐wire chemical vapor deposition yields an excellent surface passivation for phosphorous‐doped crystalline silicon (c‐Si) wafers. We find effective minority carrier lifetimes of well above 6 ms by introducing this stack. We investigated its c‐Si surface passivation mechanism in a systematic study combined with the comparison to a phosphorous‐doped polycrystalline‐Si (pc‐Si)/SiO₂ stack. In both cases, field effect passivation by the n‐doping of either the µc‐SiC:H or the pc‐Si is effective. Hydrogen passivation during µc‐SiC:H growth plays an important role for the µc‐SiC:H/SiO₂ combination, whereas phosphorous in‐diffusion into the SiO₂ and the c‐Si is operative for the surface passivation via the Pc‐Si/SiO₂ stack. The high transparency and conductivity of the µc‐SiC:H layer, a low thermal budget and number of processes needed to form the stack, and the excellent c‐Si surface passivation quality are advantageous features of µc‐SiC:H/SiO₂ that can be beneficial for c‐Si solar cells. (© 2016 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)     

Properties of an Al<Subscript>2</Subscript>O<Subscript>3</Subscript>/Si interface

The phase chemical composition of an Al₂O₃/Si interface formed upon molecular deposition of a 100-nm-thick Al₂O₃ layer on the Si(100) (c-Si) surface is investigated by depth-resolved ultrasoft x-ray emission spectroscopy. Analysis is performed using Al and Si L_{2, 3} emission bands. It is found that the thickness of the interface separating the c-Si substrate and the Al₂O₃ layer is approximately equal to 60 nm and the interface has a complex structure. The upper layer of the interface contains Al₂O₃ molecules and Al atoms, whose coordination is characteristic of metallic aluminum (most likely, these atoms form sufficiently large-sized Al clusters). The shape of the Si bands indicates that the interface layer (no more than 10-nm thick) adjacent to the substrate involves Si atoms in an unusual chemical state. This state is not typical of amorphous Si, c-Si, SiO₂, or SiO_x (it is assumed that these Si atoms form small-sized Si clusters). It is revealed that SiO₂ is contained in the vicinity of the substrate. The properties of thicker coatings are similar to those of the 100-nm-thick Al₂O₃ layer and differ significantly from the properties of the interfaces of Al₂O₃ thin layers.     

Interface state density and barrier height improvement in ammonium sulfide treated Al2O3/Si interfaces

The HF treatment removes the native oxide and lays behind the dangling bonds over the Si surface which causes the increment in density of interface traps (D_it) through the direct deposition of high-k dielectric on Si. Here, we propose the facile method for reduction of interface traps and improvement in barrier height with the (NH₄)₂S treatment on Al₂O₃/Si interfaces, which can be used as the base for the non-volatile memory device. The AFM was used to optimize the treatment time and surface properties, while XPS measurements were carried out to study the interface and extract the barrier height (Φ_B). The short period of 20 s treatment shows the improvement in the barrier height (1.02 eV), while the one order reduction in the D_it (0.84 × 10¹² cm²/eV) of sulfur passivated Al/Al₂O₃/Si MOS device. The results indicate the favorable passivation of the dangling bonds over the Si surfaces covered by sulfur atoms.     

Enhanced rear‐side reflection and firing‐stable surface passivation of silicon solar cells with capping polymer films

Low refractive index polymer materials have been investigated with a view to form the back surface mirror of advanced silicon solar cells. SiO_x:H or AlO_y SiO_x:H polymer films were spun on top of an ultra‐thin (<10 nm) atomic‐layer‐deposited (ALD) Al₂O₃ layer, itself deposited on low‐resistivity (1 Ω cm) p‐type crystalline silicon wafers. These double‐layer stacks were compared to both ALD Al₂O₃ single layers and ALD Al₂O₃/plasma‐enhanced chemical vapour deposited (PECVD) SiN_x stacks, in terms of surface passivation, firing stability and rear‐side reflection. Very low surface recombination velocity (SRV) values approaching 3 cm/s were achieved with ALD Al₂O₃ layers in the 4–8 nm range. Whilst the surface passivation of the single ALD Al₂O₃ layer is maintained after a standard firing step typical of screen printing metallisation, a harsher firing regime revealed an enhanced thermal stability of the ALD Al₂O₃/SiO_x:H and ALD Al₂O₃/AlO_y SiO_x:H stacks. Using simple two‐dimensional optical modelling of rear‐side reflection it is shown that the low refractive index exhibited by SiO_x:H and AlO_y SiO_x:H results in superior optical performance as compared to PECVD SiN_x, with gains in photogenerated current of ～0.125 mA/cm² at a capping thickness of 100 nm. (© 2013 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

XPS study of the surface chemistry on AZ31 and AZ91 magnesium alloys in dilute NaCl solution

The surface chemistry on AZ31 and AZ91 magnesium alloys was characterized by X-ray photoelectron spectroscopy (XPS) in the corrosion and the passivation zones. In the corrosion zone, the presence of Mg(OH)₂ and MgCO₃ species was found in the outer surface, whereas, in the inner layer, the co-existence of Mg(OH)₂, MgO and MgCO₃ species was observed for both alloys. The presence of Al³⁺ in the surface electrolyte to form Al₂O₃/Al(OH)₃ and the formation of carbonate product provide a better passivation on the surfaces and retard the chloride-induced corrosion on the materials in the passivation zone.     

Stacked and nanolaminated Al2O3/TiO2 for surface passivation and encapsulation of silicon

Silicon solar cells passivated with Al₂O₃ require a capping layer that protects the passivation layer from humidity because of sensitivity of Al₂O₃ to moisture. Al₂O₃/TiO₂ stacks obtained by atomic layer deposition have been known to provide a high level of passivation layers because of their excellent field‐effect passivation. In this work, degradation of this Al₂O₃/TiO₂ stack, when exposed to humidity, is examined, and an attempt is made for a humidity‐resistant encapsulation layer by adding Al₂O₃/TiO₂ nanolaminates that can be deposited in‐situ without breaking vacuum. Placing the nanolaminate on top of the TiO₂ and Al₂O₃ stack is found to lead to almost no degradation even after 10 days of humidity exposure. (© 2015 WILEY‐VCH Verlag GmbH &Co. KGaA, Weinheim)