Synthesis and performance of electroless Ni–P–TiCN composite coatings on Al substrate

Electroless Ni–P and Ni–P–TiCN composite coatings have been deposited successfully on Al substrates. Scanning electron microscopy (SEM) and energy dispersive X‐ray (EDX) techniques were applied to study the surface morphology and the chemical composition of the deposited films. Moreover, X‐ray diffraction (XRD) proved that Ni–P and Ni–P–TiCN deposits have amorphous structures. The properties of Ni–P–TiCN/Al composite films such as hardness, corrosion resistance and electrocatalytic activity were examined and compared with that of Ni–P/Al film. The results of hardness measurements reveal that the presence of TiCN particles with Ni–P matrix improves its hardness. Additionally, the performance against corrosion was examined using Tafel lines and electrochemical impedance spectroscopy techniques in both of 0.6 M NaCl and a mixture of 0.5 M H₂SO₄ with 2 ppm HF solutions. The results indicate that the incorporation of high dispersed TiCN particles into Ni–P matrix led to a positive shift of the corrosion potential and an increase in the corrosion resistance for all aluminum substrates after their coating with Ni–P–TiCN. In addition, Ni–P–TiCN/Al electrodes showed a higher electrochemical catalytic activity and stability toward methanol oxidation in 0.5 M NaOH solution compared with that of Ni–P/Al. Copyright © 2014 John Wiley & Sons, Ltd.     

Sol–Gel Synthesis of Bismuth Molybdate Catalysts for the Selective Oxidation of Propylene to Acrolein: Influence of pH Value and Theoretical Molar Atomic Ratio

Different bismuth molybdate catalysts for the selective oxidation of propylene to acrolein were prepared by the sol–gel method, starting from bismuth nitrate, ammonium molybdate, and citric acid. The influence of pH value and theoretical molar Bi/Mo atomic ratio on the complexation and gelation is surveyed using IR spectroscopy, X‐ray diffraction, and BET. Their catalytic activities for the conversion propylene to acrolein are examined.     

Electrodeposition of nanocrystalline Ni–Cu alloy from environmentally friendly lactate bath

A new environmentally friendly electroplating bath for Ni–Cu alloy deposition was developed. Lactic acid was used as a complexing agent. The influence of bath composition, current density, pH and temperature on cathodic polarization, cathodic current efficiency and alloy composition was studied. Different proportions of the two metals were obtained by using different deposition parameters, but at all [Ni²⁺] / [Cu²⁺] ratios studied, preferential deposition of Cu occurred and regular co‐deposition took place. The Ni content of the deposit increased with Ni²⁺ content and current density and decreased with temperature. The surface morphology of the deposited Ni–Cu alloy was investigated using scanning electron microscopy. The crystal structure was examined using the X‐ray diffraction technique. The results showed that the deposits consisted of a single solid solution phase with a face‐centered cubic structure. The crystallite size lies in the range of 12 to 25 nm for as‐plated alloys. Copyright © 2014 John Wiley & Sons, Ltd.     

Surface analysis and corrosion resistance of new nickel base thin film alloys

Electroless Zn–Ni–P thin films were deposited on low carbon steel from an alkaline non‐cyanide aqueous electrolyte. The newly developed ternary alloys structure and microstructure investigations were carried out via X‐ray diffraction and SEM. Chemical composition of the coatings was investigated via energy dispersive spectroscopy. Polarization tests were used to study the corrosion properties of the coatings in a 3.5 wt.% NaCl solution. The results confirmed the high corrosion resistance of Zn–Ni–P alloy plated steel sheet. The surface analysis of the thin film samples before and after corrosion was performed by XPS. The incorporation of Zn in Ni–P thin film is proven for all initial samples to be as a mixture of zinc and zinc oxide, while nickel exists in +2 and +3 oxidized states. A passive film of a mixture of oxide and hydroxide of zinc and nickel forms on the surface and prevents the Zn–Ni–P thin films from corrosion. Copyright © 2014 John Wiley & Sons, Ltd.     

Effect of nitrogen on mechanical,oxidation and structural behaviour of Ti–Si–B–C–N nanocomposite hard coatings deposited by DC sputtering

Ti–Si–B–C–N film was deposited by DC magnetron sputtering at different argon and nitrogen ratios such as N₂/Ar = 1 : 5, 2 : 4, 3 : 3, 4 : 1 and 5 : 0. The formation of TiN and TiB phases was observed because of incorporation of nitrogen. The hardness, modulus, microstructure, structure and bond formation with different nitrogen contents during the deposition were studied by nanoindentation, scanning electron microscope, X‐ray diffraction and X‐ray photoelectron spectroscopy, respectively. The oxidation kinetics of Ti–Si–B–C–N was investigated. The nitrogen incorporation during deposition influences different properties of the coating. Hardness and modulus decreased, and microstructure showed very fine grain presence, and film changes to fully amorphous because of incorporation of nitrogen in the film. Copyright © 2016 John Wiley & Sons, Ltd.     

Studies on Structure and Electrocatalytic Hydrogen Evolution of Nanocrystyalline Ni—Mo—Fe Alloy Electrodeposit Electrodes

Nanocrystalline Ni‐Mo‐Fe alloy deposits were obtained by electrode‐position. The structures of the alloy deposits were analyzed by X‐ray diffraction (XRD) and X‐ray photoelectron spectroscopy (XPS). The XRD results of nanocrystalline Ni‐Mo‐Fe alloy deposit show that many diffraction lines disappear, and that there is only one diffraction peak at 44.0°. The XPS results of nanocrystalline Ni‐Mo‐Fe alloy deposits indicate that the nickel, molybdenum and iron of the deposits exist in metallic state, and that the binding energy of the alloyed elements increases to some extent. The nanocrystalline Ni‐Mo‐Fe alloy deposit electrode may offer better electrocatalytic activity than the polycrystalline nickel electrode and the nanocrystalline Ni‐Mo alloy electrode. The electrochemical impedance spectra from the nanocrystalline Ni‐Mo‐Fe alloy electrode indicate that hydrogen evolution in 30% (m/m) KOH at lower overpotential is in accordance with the Vohner‐Tafel mechanism, but with the Vohner‐Heyrovsky mechanism at higher overpotential.     

Corrosion behavior of electroless Ni–P/TiO2 nanocomposite coatings

Composite Ni–P/nano‐TiO₂ coatings were prepared by simultaneous electroless deposition of Ni–P and nano‐TiO₂ on a low carbon steel substrate. The deposition was carried out from stirred solutions containing suspended nano‐TiO₂ particles. The Ni–P and Ni–P/nano‐TiO₂ coatings before and after heat treatment were characterized by X‐ray diffraction, scanning electron microscopy and energy dispersive X‐ray spectroscopy. The micro‐structural morphologies of the coatings significantly varied with the nano‐TiO₂ content. The corrosion resistance of as‐plated and heat‐treated Ni–P and Ni–P/nano‐TiO₂ coatings was investigated by anodic polarization, Tafel plots and electrochemical impedance spectroscopic (EIS) studies in 3.5% NaCl solution. Ni–P/nano‐TiO₂ coating exhibited superior corrosion resistance over Ni–P coating. Copyright © 2015 John Wiley & Sons, Ltd.     

碳电极上电沉积的Ni-MgO纳米复合物催化甲醇和乙醇电氧化反应

在细小MgO增强颗粒的存在下,采用电沉积法在碳阳极上经瓦特镍制得Ni–MgO纳米复合物,考察了它在碱性介质中电催化氧化甲醇和乙醇反应性能,并与碳涂覆的纯Ni催化剂(Ni/C)性能进行了比较。运用能量散射谱、X射线衍射和扫描电镜分别表征了沉积的纳米复合物的化学组成、相结构和表面形貌,并采用循环伏安法(CV)、计时电流法和电化学阻抗谱(EIS)等电化学技术考察了所制电催化剂阳极的催化活性。结果表明, Ni/C催化剂在电氧化反应中表现出很低的催化活性和稳定性,而MgO的引入显著增加了Ni催化剂在醇氧化反应中的催化活性和抗中毒性能。 EIS和CV结果证实Ni–MgO/C纳米复合物电极具有比Ni/C更低的电荷转移阻力和更高的抗中毒性能。     

Effect of Cu in electroless Ni–Cu–P coating on passivation process

Electroless Ni–P and Ni–Cu–P coatings were passivated by chromate conversion treatment respectively. The anticorrosive performances of passivated coatings were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy measurements. The passivated Ni–Cu–P coating exhibited a high corrosion resistance with the i_corr of 0.236 μA/cm,² while the value of passivated Ni–P coating was only 1.030 μA/cm,² indicating the passive film could improve the corrosion resistance of Ni–Cu–P coating to a significant extent. High‐resolution X‐ray photoelectron spectroscopy was used to determine the chemical states of elements detected in the passive film. Compared with passivated Ni–P coating, the passive film on Ni–Cu–P coating exhibited a higher ratio of Cr₂O₃ to Cr(OH)₃ with the value of 72:28, which was the main factor for passivated Ni–Cu–P coating showing excellent corrosion resistance. The effect of Cu in electroless Ni–Cu–P coating on passivation process was discussed by the contrast experiment. Copyright © 2016 John Wiley & Sons, Ltd.     

Intermediate molybdenum oxides involved in binary and ternary induced electrodeposition

The first stages of Co–Ni and Co–Ni–Mo deposition in sulphate–citrate medium at pH 4.0 were analysed. In both cases, the formation of non-hydrogenated nickel on the electrode before alloy deposition was detected by linear sweep voltammetry and inductively coupled plasma mass spectrometry. Co–Ni electrodeposition was anomalous since the Co/Ni ratio in the alloy was higher than the corresponding [Co(II)]/[Ni(II)] ratio in solution. The adsorption of Co(II) over the initial nickel could explain the anomalous codeposition, which persisted with the addition of molybdate to the Co–Ni bath. However, the formation of intermediate molybdenum oxides also took place. A mechanism has been proposed to describe the sequence of steps for Co–Ni–Mo electrodeposition. Under our conditions, the alloy is formed mainly from free Co²⁺ and Ni²⁺ cations, whereas molybdate is reduced firstly to molybdenum oxide from MoO₄(H₃Cit)²⁻ and, secondly, NiCit⁻ catalyses the subsequent reduction to molybdenum metal of the intermediate [MoO₂–NiCit⁻]_ads species.     

C–C bridged Ni(II) complexes bearing β‐keto‐9‐fluorenyliminato ligands prepared by different in situ bonding mechanisms and their use in catalytic (co)polymerization of norbornene and styrene

Two C–C bridged Ni(II) complexes bearing β‐keto‐9‐fluorenyliminato ligands with electron‐withdrawing groups (─CF₃), Ni{PhC(O)CHC[N(9‐fluorenyl)]CF₂}₂ (Ni 1 ) and Ni{CF₃C(O)CHC[N(9‐fluorenyl)]Ph}₂ (Ni 2 ), were synthesized by metal coordination reaction and different in situ bonding mechanisms. The C–C bridged bonds of Ni 1 were formed by in situ intramolecular trifluoromethyl and 9‐fluorenyl carbon–carbon cross‐coupling reaction and those of Ni 2 were formed by in situ intramolecular 9‐fluorenyl carbon–carbon radical coupling reaction mechanism. The obtained complexes were characterized using ¹H NMR spectroscopy and elemental analyses. The crystal and molecular structures of Ni 1 and Ni 2 with C–C bridged configuration were determined using X‐ray diffraction. Ni 1 and Ni 2 were used as catalysts for norbornene (NB) polymerization after activation with B(C₆F₅)₃ and the catalytic activities reached 10⁶ g_polymer mol_Ni^?1 h^?1. The copolymerization of NB and styrene catalyzed by the Ni 1 /B(C₆F₅)₃ system showed high activity (10⁵ g_polymer mol_Ni^?1 h^?1) and the catalytic activities decreased with increasing feed content of styrene. All vinyl‐type copolymers exhibited high molecular weight (10⁴ g mol^?1), narrow molecular weight distribution (M_w/M_n = 1.71–2.80), high styrene insertion ratios (11.13–50.81%) and high thermal stability (T_d > 380°C) and could be made into thin films with high transparency in the visible region (400–800 nm).     

Cobalt titanate–cobalt oxide composite thin films deposited from heterobimetallic precursor

A single molecular heterobimetallic complex, [Co₂Ti(μ₃‐O)(TFA)₆(THF)₃] (1) [TFA = trifluoroacetate, THF = tetrahydrofuran], was synthesized, structurally and spectroscopically characterized and implemented as a single‐source precursor for the preparation of CoTiO₃–CoO composite thin films by aerosol‐assisted chemical vapour deposition (AACVD). The precursor complex was prepared by interaction of Co(OAc)₂.4H₂O [OAc = (CH₃COO^?)] with Ti(iso‐propoxide)₄ in the presence of trifluoroacetic acid in THF, and was analysed by melting point, CHN, FT‐IR, single‐crystal X‐ray diffraction and thermogravimetric analysis. The precursor complex thermally decomposed at 480 °C to give a residual mass corresponding to a CoTiO₃–CoO composite material. Good‐quality crystalline CoTiO₃–CoO composite thin films deposited at 500 °C by AACVD and characterized through powder X‐ray diffraction and scanning electron microscopy/energy‐dispersive X‐ray spectroscopy show that the crystallites have a rose‐flower‐like morphology with an average petal size in the range of 2–6 µm. Copyright © 2012 John Wiley & Sons, Ltd.     

Generation of Photocurrent by Visible‐Light Irradiation of Conjugated Dawson Polyoxophosphovanadotungstate–Porphyrin Copolymers

Four hybrid polyoxometalate–porphyrin copolymer films were obtained by the electrooxidation of zinc octaethylporphyrin in the presence of four different Dawson‐type polyoxometalates bearing two pyridyl groups (POM(py)₂) with various spacers. The POM monomers were designed around 1,3,5‐trisubstituted benzene rings. Two of the substituents of the benzene ring are linked to the pyridyl groups, and the third is connected to the POM subunit. The four monomers vary in the relative positions of the nitrogen atoms of the pyridine rings or in the distance from the carbonyl group. The monomers were fully characterized by ¹H, ³¹P, and ¹³C NMR spectroscopy, electrospray mass spectrometry, IR and UV/Vis spectroscopy, and electrochemistry. The copolymers were characterized by UV/Vis spectroscopy, X‐ray photoelectron spectroscopy, electrochemistry, and AFM. Their photovoltaic performance under visible light irradiation was investigated by photocurrent transient measurements under visible illumination.     

Electrodeposition and characterization of Zn–Sn alloy coatings from a deep eutectic solvent based on choline chloride for corrosion protection

With the aim of obtaining high corrosion resistant Zn–Sn alloy coatings from an ionic liquid, the effects of electrodeposition potential and electrolyte composition on the electrodeposition behavior, film composition, morphology and corrosion performance were investigated. Cyclic voltammograms indicate that Zn and Sn were co‐deposited at distinct reduction potentials as pure Zn and Sn elements. In addition, the phase composition analysis also showed that the obtained Zn–Sn alloy deposits (8 wt.%–45 wt.% Zn) consist of a two‐phase mechanical mixture of small aggregates of Zn and Sn metals. The Zn content of the alloy significantly increases as the electrodeposition potential and electrolyte Zn (II)/Sn (II) ratio increase. The corrosion performance study of the obtained Zn–Sn coatings showed that they have a passivation behavior and their corrosion resistance increases as the alloy‐Sn content increases. To improve their morphological properties, ethylene diamine tetraacetic acid additive was introduced into the electrolyte and greatly improved the morphology and corrosion resistance of the deposits. For the first time, it was shown that high corrosion resistance Zn–Sn coatings can be obtained from ionic liquids. Copyright © 2014 John Wiley & Sons, Ltd.     

Preparation of nanostructured Co–Mo alloy electrodes and investigation of their electrocatalytic activity for hydrazine oxidation in alkaline medium

Cobalt and cobalt–molybdenum alloy electrodes are prepared by galvanic deposition on copper substrates. In this paper, we report a study on the influence of alloying cobalt with molybdenum for the oxidation of hydrazine in 1 M NaOH aqueous solutions. The electrocatalytic properties of the electrodes are studied by cyclic voltammetry (CV), chronoamperometry (CA), and electrochemical impedance spectroscopy (EIS). Scanning electron microscopy (SEM), X‐ray diffraction (XRD), energy‐dispersive X‐ray spectroscopy (EDS,) and inductively coupled plasma (ICP) analysis demonstrate that the structural features and compositions of the as‐prepared Co–Mo coatings vary with the deposition conditions. Electrochemical characterization indicates that the electrochemical properties and the electrocatalytic activity of the investigated alloys were strongly dependent on the microstructural features obtained under different deposition conditions. The overall experimental data indicate that alloying cobalt with molybdenum metal leads to an increase of the electrocatalytic activity in hydrazine electroxidation compared to when using the pure cobalt electrode. High catalytic efficiencies were achieved on Co/25 at.% Mo and Co/33 at.% Mo electrodes, the latter being the best electrocatalyst for hydrazine electroxidation.     

Efficient and recyclable novel Ni‐based metal–organic framework nanostructure as catalyst for the cascade reaction of alcohol oxidation–Knoevenagel condensation

A novel Ni‐based metal–organic framework (Ni‐MOF) with a Schiff base ligand as an organic linker, Ni₃(bdda)₂(OAc)₂?6H₂O (H₂bdda = 4,4′‐[benzene‐1,4‐diylbis(methylylidenenitrilo)]dibenzoic acid), was synthesized and characterized using powder X‐ray powder diffraction, thermogravimetric analysis, Brunauer–Emmett–Teller measurements, inductively coupled plasma atomic emission spectroscopy, transmission electron microscopy, elemental analysis and Fourier transform infrared spectroscopy. The synthesized Ni‐MOF exhibited a high catalytic activity in benzyl alcohol oxidation using tert‐butyl hydroperoxide under solvent‐free conditions. Also, the efficiency of the catalyst was investigated in the cascade reaction of oxidation–Knoevanagel condensation under mild conditions. The Ni‐MOF catalyst could be recovered and reused four times without significant reduction in its catalytic activity.     

A highly active multi‐usable palladium pyridylfluorene film‐based catalyst for C–C cross‐coupling reactions

The two terminal pyridyl nitrogen atoms of 2,7‐bis(4‐pyridyl)fluorene ( 1 ) were coordinated to Pd(II) ions to give self‐assembled, multilayer films using the layer‐by‐layer (LbL) method. The films were prepared by alternately dipping the substrate, pre‐coated with a polyethyleneimine layer, in aqueous solutions of PdCl₂ and ethanol solutions of 1 . The resulting films were characterized using UV–visible absorption spectroscopy, atomic force microscopy (AFM), X‐ray photoelectron spectroscopy, scanning electron microscopy (SEM) and inductively coupled plasma atomic emission spectroscopy (ICP‐AES). UV–visible spectra and SEM images show almost uniform growth of the film in a near ideal LbL manner. AFM images show that nanostructured aggregates of Pd(II) complexes form on the surface. With an increase in the number of Pd(II)/ 1 bilayers, more particulate aggregates are distributed on the surface. When released from the substrate, the Pd(II) complex nanostructure shows high catalytic activity for Suzuki–Miyaura and Mizoroki–Heck cross‐coupling reactions. The catalyst loading is as low as 9.1 × 10^?3 mol% Pd, as measured using ICP‐AES, and high turnover numbers of up to 1.08 × 10⁴ are obtained. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of Ni–Ru Alloy Nanoparticles and Their High Catalytic Activity in Dehydrogenation of Ammonia Borane

We report the synthesis and characterization of new Ni_xRu_1?x (x=0.56–0.74) alloy nanoparticles (NPs) and their catalytic activity for hydrogen release in the ammonia borane hydrolysis process. The alloy NPs were obtained by wet‐chemistry method using a rapid lithium triethylborohydride reduction of Ni²⁺ and Ru³⁺ precursors in oleylamine. The nature of each alloy sample was fully characterized by TEM, XRD, energy dispersive X‐ray spectroscopy (EDX), and X‐ray photoelectron spectroscopy (XPS). We found that the as‐prepared Ni–Ru alloy NPs exhibited exceptional catalytic activity for the ammonia borane hydrolysis reaction for hydrogen release. All Ni–Ru alloy NPs, and in particular the Ni_0.74Ru_0.26 sample, outperform the activity of similar size monometallic Ni and Ru NPs, and even of Ni@Ru core‐shell NPs. The hydrolysis activation energy for the Ni_0.74Ru_0.26 alloy catalyst was measured to be approximately 37 kJ mol^?1. This value is considerably lower than the values measured for monometallic Ni (≈70 kJ mol^?1) and Ru NPs (≈49 kJ mol^?1), and for Ni@Ru (≈44 kJ mol^?1), and is also lower than the values of most noble‐metal‐containing bimetallic NPs reported in the literature. Thus, a remarkable improvement of catalytic activity of Ru in the dehydrogenation of ammonia borane was obtained by alloying Ru with a Ni, which is a relatively cheap metal.     

Effect of P codeposition on the structure and microhardness of Co–W coatings electrodeposited from gluconate bath

Effects of addition of P to Co–W coatings from gluconate bath using direct current (DC) and pulse current (PC) methods have been investigated in this study. Co–W–P coatings with different P concentrations are prepared by varying hypophosphite concentration in the bath. Current efficiency of the Co–W–P electrodeposition is lower than that for Co–W coatings. Increase in NaH₂PO₂ concentration increases the cobalt content significantly and decreases the tungsten content drastically. Co–W–P coatings display ‘cauliflower‐like’ morphology and roughness of the coatings increases with increasing P content. As‐deposited Co–W–P deposits are amorphous while heat treatment at different temperatures has rendered them crystalline with the precipitation of stable species like, Co₃W, Co₂P, etc. Unlike Co–W coatings, Co–W–P shows two‐step crystallization in differential scanning calorimetry (DSC) and on heat treatment, which is similar to the behavior of Co–P electrodeposited from gluconate baths. Moreover, inclusion of phosphorous and heat treatment have led to significant increase in microhardness of the Co–W–P coatings. X‐ray photoelectron spectroscopy (XPS) studies provide a detailed insight into the nature of Co, W and P species in as‐deposited and sputtered coatings. Microhardness of the heat‐treated coatings is higher than the as‐deposited counterparts and is comparable with that of hard chromium. Copyright © 2016 John Wiley & Sons, Ltd.     

Metal–Metal Interactions in Heterobimetallic Complexes with Dinucleating Redox‐Active Ligands

The tuning of metal–metal interactions in multinuclear assemblies is a challenge. Selective P coordination of a redox‐active PNO ligand to Au^I followed by homoleptic metalation of the NO pocket with Ni^II affords a unique trinuclear Au–Ni–Au complex. This species features two antiferromagnetically coupled ligand‐centered radicals and a double intramolecular d⁸–d¹⁰ interaction, as supported by spectroscopic, single‐crystal X‐ray diffraction, and computational data. A corresponding cationic dinuclear Au–Ni analogue with a stronger d⁸–d¹⁰ interaction is also reported. Although both heterobimetallic structures display rich electrochemistry, only the trinuclear Au–Ni–Au complex facilitates electrocatalytic C?X bond activation of alkyl halides in its doubly reduced state. Hence, the presence of a redox‐active ligand framework, an available coordination site at gold, and the nature of the nickel–gold interaction appear to be essential for this reactivity.