Highly sensitive determination of 1,1-dimethylhydrazine by high-performance liquid chromatography–tandem mass spectrometry with precolumn derivatization by phenylglyoxal

A new highly sensitive and rapid approach to the determination of 1,1-dimethylhydrazine in natural water is developed (determination range is 0.03–1 μg/L). It is based on the use of high-performance liquid chromatography–tandem mass spectrometry with precolumn derivatization by phenylglyoxal and does not require any preconcentration. Derivatization, chromatographic separation conditions, and tandem mass spectrometry detection parameters are chosen. Intra-day precision of the results of measurements of 1,1- dimethylhydrazine in natural water is 12–16%, and inter-day precision is 16–22%. The lowest limit of detection and the lowest limit of quantification are 0.010 μg/L and 0.030 μg/L, respectively.     

The determination of hydrazine and 1,1-dimethylhydrazine,separately or in mixtures,by high-pressure liquid chromatography

A rapid, sensitive liquid chromatographic method for the determination of hydrazine and 1,1-dimethylhydrazine, separately or in mixtures of varying proportions, is described. The procedure involves salicylaldehyde derivative formation followed by chromatography on a reversed phase (octadecylsilane) column with acetonitrile (52%)—0.14 M potassium dihydrogenphosphate (48%) as a mobile phase and u.v. (254 nm) detection. This system is sensitive to 2 μg ml^-1 of hydrazine and 5 μg ml^-1 of 1,1-dimethylhydrazine and has a relative standard deviation of less than 1%. Monomethylhydrazine forms an unstable salicylaldehyde hydrazone; although it cannot be determined, it can be detected (sensitivity 5 μg ml^-1 ) and does not interfere with quantitative measurement of either hydrazine or 1,1-dimethylhydrazine.     

Spectrophotometric determination of hydrazine and 1,1-dimethylhydrazine,separately or in admixture

A rapid, sensitive spectrophotometric method for the determination of hydrazine and 1,1-dimethylhydrazine, separately or in mixtures of varying proportions, is described. The analysis is based on the well-known reaction of these compounds with salicylaldehyde to form, in the case of hydrazine, a symmetrical azine, or with 1,l-dimethylhydrazine, a hydrazone. Absorbance measurements were made in the ultraviolet at wavelengths characteristic of the derivatives and of salicylaldehyde; the results were calculated by means of simultaneous equations. The procedure is sensitive to concentrations of hydrazine as low as 0.3 μg/ml and of 1,1-dimethylhydrazine as low as 0.25 μg/ml. This corresponds to initial sample solutions having a concentration of 3.0 mg of hydrazine and 1.25 mg of 1,1-dimethyl hydrazine per ml.     

Simultaneous Determination of Hydrazine,Methylhydrazine, and 1,1-Dimethylhydrazine by High-Performance Liquid Chromatography with Pre- and Post-Column Derivatization by 5-Nitro-2-Furaldehyde

Approaches to the chromatographic determination of 1,1-dimethylhydrazine and two main products of its degradation (hydrazine and methylhydrazine) on their simultaneous presence are proposed using derivatization by 5-nitro-2-furaldehyde and multi-wavelength spectrophotometric detection of the formed derivatives in the visible spectral region. A combination of preliminary derivatization with separation in the reversed-phase HPLC mode and also ion-chromatographic separation with post-column derivatization allowed us to reach the limits of detection for analytes lower than 1 μg/L and to determine 1,1-dimethylhydrazine at the level of the maximum permissible concentration without preconcentration. The developed approaches were tested on an acid extract of a sample of peat bog soil collected at the place of impact of the first stage of a carrier rocket. The identity of the results obtained by different methods and the high level of soil pollution by hydrazines are shown.     

Spectrophotometric determination of hydrazine,methylhydrazine, and 1,1-dimethylhydrazine with preliminary derivatization by 5-nitro-2-furaldehyde

5-Nitro-2-furaldehyde, a new derivatizing agent for the spectrophotometric determination of hydrazine, methylhydrazine, and 1,1-dimethylhydrazine is proposed. It is characterized by high solubility in water and by a substantial difference in the positions of absorption bands of the formed colored derivatives. The kinetics of the reaction of analyte derivatization is studied, and reaction conditions (pH 5, concentration of derivatizing agent 2 mM, 60° C, duration 40 min) are optimized. The limits of detection are 5, 3, and 1.5 μg/L for hydrazine, methylhydrazine, and 1,1-dimetlhydrazine, respectively. A possibility of the spectrophotometric determination of analytes in their simultaneous presence using the Firordt method is shown. The developed approach is successfully applied to the analysis of polluted peat bog soil selected at a place of impact of the first step of a carrier rocket.     

Rapid Test Determination of Iron(II) in Aqueous Media by Reagent Indicator Paper

A reagent indicator paper with immobilized zirconyl hexacyanoferrate(III) is prepared for the preconcentration and determination of 0.05–500 mg/L of iron(II) in the presence of more than 100-fold amount of iron(III). The paper is stable in the presence of up to 200 mg/L of 1,1-dimethylhydrazine. The test method is successfully verified using a color comparator or a minireflectometer with a red light-emitting diode as applied to samples of natural water from drilling mud flows and aqueous solutions containing 1,1-dimethylhydrazine.     

Determination of 1,1-Dimethylhydrazine by Reversed-Phase High-Performance Liquid Chromatography with Spectrophotometric Detection as a Derivative with 4-Nitrobenzaldehyde

A procedure was developed for the determination of 1,1-dimethylhydrazine by reversed-phase high-performance liquid chromatography with spectrophotometric detection and preliminary derivatization by the reaction with 4-nitrobenzaldehyde. Conditions were selected for the chromatographic separation and the detection of the peaks of the reagent and 4-nitrobenzaldehyde dimethylhydrazone. The optimum conditions were found for the derivatization of 1,1-dimethylhydrazine with 4-nitrobenzaldehyde. The determination limit of 1,1-dimethylhydrazine in aqueous solutions was 120 g/L (2 M/L).     

Sorption-chromatographic determination of hydrazine and its substituted derivatives in air

Working conditions were found for the chemisorption preconcentration of hydrazine, phenylhydrazine, and 1,1-dimethylhydrazine from air with tubes containing silica gel with immobilized 4-chloro-5,7-dinitrobenzofurazan and the subsequent determination by high-performance liquid chromatography with diode array detection. A recovery of 98% (hydrazine), 90% (phenylhydrazine), and 97% (1,1-dimethylhydrazine) is attained at a thickness of the sorbent layer of 2 cm, an aspiration rate of 0.2–0.8 L/min, and a volume of aspirated air of 10 L. Silica gel with a particle size of 0.1–0.3 mm impregnated with 4-chloro-5,7-dinitrobenzofurazan (2 wt %) was used as the sorbent. The detection limits of compounds without regard for preconcentration after their desorption are 0.01 (hydrazine), 0.017 (1,1-dimethylhydrazine), and 0.015 mg/m³ (phenylhydrazine).     

Application of the localized surface plasmon resonance of gold nanoparticles for the determination of 1,1-dimethylhydrazine in water: Toward green analytical chemistry

Localized surface plasmon resonance (LSPR) is an optical phenomena generated by light when it interacts with conductive nanoparticles that are smaller than the incident wavelength. In this work, we proposed a simple, fast, and green method for spectrophotometric determination of unsymmetrical 1,1-dimethylhydrazine (UDMH) based on LSPR property of gold nanoparticles (AuNPs). An LSPR band is produced via reduction of Au³⁺ ions in solution by UDMH as active reducing agent in the presence of cetyltrimethylammonium chloride as a capping agent. Some important parameters in the formation of LSPR including Au(III) concentration, pH, concentration of stabilizer, and reaction time were studied and optimized. Under optimum conditions, the LSPR intensity displays linear response with the increasing UDMH concentration in the range from 0.5–10 μg/mL at 550 nm with a detection limit of 0.2 μg/mL. Also, the relative standard deviation for ten replicate determination of 5.0 μg/mL of UDMH was 3%. Usage of AuNPs as new nontoxic reagent instead of hazardous reagents in the spectrophotometric determination of UDMH is a step toward green analytical chemistry. The proposed method was successfully applied for determination of UDMH in water and wastewater samples.     

顶空固相微萃取-气相色谱-质谱法同时测定饮用水源水中24种VOCs

建立了同时测定饮用水源水中24种挥发性有机物(VOCs)的顶空固相微萃取-气相色谱-质谱法.用75 μm CarboxenTM-Polydimethylsiloxane(CAR-PDMS)固相微萃取柱顶空萃取水样中的VOCs,VOCs用气相色谱-质谱联用仪检测,采用内标法定量.对萃取柱涂层、样品盐度、萃取温度和萃取时间等样品前处理条件进行了优化,VOCs的检出限在0.03～0.31 μg/L之间,线性相关系数r＞0.996(二氯甲烷和三氯甲烷除外).对饮用水源水实际水样0.50μg/L和1.00 μg/L两个加标浓度水平的回收率进行了测定,三氯甲烷回收率均值分别为104％和142％,其余VOCs回收率分别为90.0％～120％和88.0％～110％,除二氯甲烷和三氯甲烷外,其余VOCs测定结果的相对标准偏差均小于15.0％(n=6).该方法适用于饮用水源水中挥发性有机物的监测分析.     

A flow injection chemiluminescence system for the determination of isoniazid

A chemiluminescence (CL) flow system is described for the determination of isoniazid based on its enhancement on the chemiluminescence (CL) emission produced upon mixing a hexacyanoferrate(III) solution with an alkaline luminol solution. The system responds linearly to isoniazid concentration in the range 0–1 mg/L with a detection limit (3σ) of 0.03 μg/L, relative standard deviation (RSD) of 1.2% for 0.1 mg/L isoniazid (n = 11). The system has been successfully applied to the determination of isoniazid in pharmaceutical preparations.     

Anodic Stripping Potentiometric Determination of Cu,Pb, Cd and Zn In Natural Waters on a Novel Combined Electrode System

Abstract

A method is described for the reliable determination of copper, lead, cadmium and zinc in natural waters by anodic stripping potentiometry with the use of a novel combined electrode. The method involves two stripping cycles during which copper is initially determined on its own, followed by simultaneous determination of lead, cadmium and zinc after addition of gallium (III) ions. The optimum conditions include 0.01 M HCl as supporting electrolyte, 10 mg/L Hg (II) as chemical oxidant; E_dep(Cu) -700 mV vs Ag/AgCl; E_{dep(Pb,Cd,Zn)} -1200 mV vs Ag/AgCl; t_dep 10s; 150 μg/L Ga (III); sample rotation rate 5 and rest period 30s. Under these conditions, as low as 0.06 μg/L Cu (0.7% RSD); 0.2 μg/L Pb (13% RSD); 0.04 μg/L Cd (7.8% RSD) and 0.06 μg/L Zn (5.5% RSD) can be determined reliably. A linear concentration range of 0–110 μg/L was obtained for the four metals. The successful application of the method to reference fresh water, creek water and tap water is demonstrated.     

The use of glyoxal and glyoxylic acid to determine N- and N,N-alkyl-substituted hydrazines by liquid chromatography

Using chromatography and spectrophotometry, it has been shown that the reaction of 1,1-dimethylhydrazine (UDMH), methylhydrazine (MH), and 2-hydroxyethylhydrazine (HEH) with excess of glyoxal (Gl) and glyoxylic acid (GlA) in aqueous solutions yields corresponding monohydrazones as single derivatization products. The derivatization reaction occurs in a quantitative yield for 20 min at 25 or 40°C for Gl and GlA, respectively (pH 3.5). The electronic absorption spectra of the derivatives have maxima in the range of 275–305 nm. The conditions for the simultaneous determination of hydrazines in waters by reversed-phase HPLC coupled with UV detection in aqueous solutions with preliminary derivatization are proposed. The derivatives are separated on a Zorbax SB-C18 (150 × 4.6 mm) column with a mobile phase of 20 mM phosphate buffer solution (pH 3.5) and 2–5% acetonitrile. The detection limits are 0.25–0.5 or 0.4–0.7 μg/L for the derivative of Gl and GlA, respectively.     

Simultaneous determination of three organophosphorus pesticides in different food commodities by gas chromatography with mass spectrometry

A sensitive and selective gas chromatography with mass spectrometry method was developed for the simultaneous determination of three organophosphorus pesticides, namely, chlorpyrifos, malathion, and diazinon in three different food commodities (milk, apples, and drinking water) employing solid‐phase extraction for sample pretreatment. Pesticide extraction from different sample matrices was carried out on Chromabond C₁₈ cartridges using 3.0 mL of methanol and 3.0 mL of a mixture of dichloromethane/acetonitrile (1:1 v/v) as the eluting solvent. Analysis was carried out by gas chromatography coupled with mass spectrometry using selected‐ion monitoring mode. Good linear relationships were obtained in the range of 0.1–50 μg/L for chlorpyrifos, and 0.05–50 μg/L for both malathion and diazinon pesticides. Good repeatability and recoveries were obtained in the range of 78.54–86.73% for three pesticides under the optimized experimental conditions. The limit of detection ranged from 0.02 to 0.03 μg/L, and the limit of quantification ranged from 0.05 to 0.1 μg/L for all three pesticides. Finally, the developed method was successfully applied for the determination of three targeted pesticides in milk, apples, and drinking water samples each in triplicate. No pesticide was found in apple and milk samples, but chlorpyrifos was found in one drinking water sample below the quantification level.     

超高效液相色谱-串联质谱联用法同步检测抗生素生产废水中螺旋霉素与新螺旋霉素残留

采用超高效液相色谱-串联质谱法同步测定了抗生素生产废水中残留的螺旋霉素(SPM-Ⅰ)和新螺旋霉素(NSPM-Ⅰ)。考察了萃取溶剂种类、水样pH值、萃取次数、水样与萃取溶剂的体积比等因素对目标物回收率的影响。以ACQUITY UPLC BEH C18(100 mm×2.1 mm i.d.,1.7 μm)为分析柱,0.1%甲酸水溶液和乙腈为流动相梯度淋洗,流速0.2 mL/min,电喷雾正离子多重反应监测模式检测。标准曲线在0.02~1.00 mg/L范围内线性关系良好,r2均大于0.999。方法回收率为70% ~ 88%,相对标准偏差小于10%,检出限(S/N=3)分别为0.03 μg/L(SPM-Ⅰ)和0.06 μg/L(NSPM-Ⅰ)。该方法应用于无锡市某制药厂抗生素生产废水中SPM-Ⅰ和NSPM-Ⅰ的检测,检出质量浓度分别为（115.6±2.7） mg/L和（5.3±0.4） mg/L。     

Determination of hydrazines by chip electrophoresis with contactless conductivity detection

In this report, a new approach for the fast determination of hydrazine compounds (hy) in complex matrices is presented. The experimental protocol is based on poly(methylmethacrylate) (PMMA) microchip separations with contactless conductivity detection using a compact portable device, which integrates all separation and detection components. Three hy (hydrozine (Hy), methylhydrazine (MH), and 1,1-dimethylhydrazine (UDMH)) were separated within < 30 s at a separation voltage of 3.8 kV using a L(-)-histidine/2-(N-morpholinoethanesulfonic acid) (His/MES) buffer (25:50 mM, pH 5.87). The contactless conductivity detection enables detection limits for Hy, MH, and UDMH of 11.9, 35.5, and 337.8 ng/mL, respectively, with linear concentration dependence up to 10 μg/mL. In complex matrices such as soil samples or river water, interferences were eliminated by implementing ultrasound-assisted headspace single-drop microextraction of hy under strongly alkaline conditions, using an aqueous drop of His/MES buffer as the extractant phase. The incorporation of this miniaturized sample preparation step led to improved limits of detection for Hy, MH, and UDMH of 6.5, 15.3, and 11.4 ng/mL, respectively. The overall protocol demonstrates a promising approach for interfacing chip electrophoresis with real-world applications.     

Determination of volatile chlorinated hydrocarbons in water samples by static headspace gas chromatography with electron capture detection

A simple, efficient, solvent‐free, and commercial readily available approach for determination of five volatile chlorinated hydrocarbons in water samples using the static headspace sampling and gas chromatography with electron capture detection has been described. The proposed static headspace sampling method was initially optimized and the optimum experimental conditions found were 10 mL water sample containing 20% w/v sodium chloride placed in a 20 mL vial and stirred at 50ºC for 20 min. The linearity of the method was in the range of 1.2–240 μg/L for dichloromethane, 0.2–40 μg/L for trichloromethane, 0.005–1 μg/L for perchloromethane, 0.025–5 μg/L for trichloroethylene, and 0.01–2 μg/L for perchloroethylene, with coefficients of determination ranging between 0.9979 and 0.9990. The limits of detection were in the low μg/L level, ranging between 0.001 and 0.3 μg/L. The relative recoveries of spiked five volatile chlorinated hydrocarbons with external calibration method at different concentration levels in pure, tap, sea water of Jiaojiang Estuary, and sea water of waters of Xiaomendao were in the range of 91–116, 96–105, 86–112, and 80–111%, respectively, and with relative standard deviations of 1.9–3.6, 2.3–3.5, 1.5–2.7, and 2.3–3.7% (n = 5), respectively. The performance of the proposed method was compared with traditional liquid–liquid extraction on the real water samples (i.e., pure, tap, and sea water, etc.) and comparable efficiencies were obtained. It is concluded that this method can be successfully applied for the determination of volatile chlorinated hydrocarbons in different water samples.     

化学修饰丝网印刷薄片碳电极测定痕量铜

采用丝网印刷技术制备一次性薄片碳电极,并在此电极上进行了化学修饰,于邻苯二酚－甲醛－NaOH溶液中的,在－0．1V~1.2V电位范围内,循环发法进行电聚合,可获得性能良好的修饰电极,该电极可用于阳极深出伏安法测量痕量铜,其响应灵敏度较裸碳电极提高50倍以上,线笥范围为2．5~50μg/L;测量的RSD为2．7％,用该电极可直接测定当是自来水中铜的含量为6．27μg/L。     

Fluorometric determination of formaldehyde

A simple, selective and sensitive fluorometric method is presented for the determination of formaldehyde in water based on its reaction with 3,4-diaminoanisole in alkaline ethanol-water solution to give a strongly fluorescing Schiff base. The dependence of the fluorescence intensity on the solvent composition, quenching by acetic and sulphuric acid, heating time and interference by other compounds is discussed. The detection limit of the method is 0.6 μg/L. The recovery of formaldehyde spiked into river water is 93% with an R.S.D of 6.05% at a concentration level of 10 μg/L.     

Electrothermal Atomic Absorption Spectrometric Determination of Cobalt,Copper and Nickel in Fresh Water After Their Preconcentration by Precipitate Flotation

Abstract

A method is developed for simultaneous separation and determination of μg/L levels of Co(II), Cu(II) and Ni(II) in fresh water by precipitate flotation. The optimal conditions of the experimental procedure with hydrated iron(III) oxide and iron(III) tetramethylenedithiocarbamate as collectors were investigated. The pH interval of the working medium, within which Co(II), Cu(II) and Ni(II) can be successfully separated, was determined from the aspect of collectors and surfactant stability. The amounts of the elements investigated were determined by electrothermal atomic absorption spectrometry. The detection limit of the method is 0.15 μg/L for cobalt, 0.03 μg/L for copper and 0.79 μg/L for nickel.