四甲基氢氧化铵改性聚偏氟乙烯接枝苯乙烯磺化膜的制备和性能

使用四甲基氢氧化铵(TMAH)甲醇溶液在液相中改性聚偏氟乙烯(PVDF),挥发溶剂得到改性聚偏氟乙烯膜(g-PVDF-M),再以过氧化苯甲酰(BPO)为引发剂,将苯乙烯接枝到g-PVDF-M膜中,磺化后制得改性聚偏氟乙烯接枝苯乙烯磺化(PVDF-g-PSSA)膜.利用傅里叶变换红外光谱(FTIR)和能谱仪的扫描电子显微镜分析了PVDF-g-PSSA膜(TMAH-25)的结构、形貌及硫元素分布情况.通过电化学工作站和气相色谱仪研究了TMAH在甲醇中的不同含量对PVDF-g-PSSA膜质子电导率和甲醇渗透率的影响.结果表明,TMAH使PVDF脱去HF生成碳碳双键,并且苯乙烯接枝到改性的聚偏氟乙烯膜中,磺化后S元素在PVDF-g-PSSA膜内部均匀分布;PVDF-g-PSSA膜的质子电导率和甲醇渗透率随TMAH在甲醇溶液中质量分数的增加而增大;TMAH的质量分数为25%时,PVDF-g-PSSA膜的电导率达1.28×10~(-2)S/cm,甲醇渗透率为4.58×10~(-7)cm~2/s.热重分析(TGA)表明,PVDF-g-PSSA膜的热稳性良好,耐热温度高达195℃,PVDF-g-PSSA膜作为电解质材料的直接甲醇燃料单电池(DMFC)功率密度达到16.45 mW/cm~2.     

碱处理PVDF膜对制备高电导率质子交换膜的作用

燃料电池是一种高能量密度、低污染的新型能源. 质子交换膜是燃料电池的核心组件之一. 在对聚偏氟乙烯(PVDF)膜进行了碱处理改性的基础上制备了高电导率的聚偏氟乙烯接枝聚苯乙烯磺酸(PVDF-g-PSSA)质子交换膜, 对碱处理后的PVDF膜进行了傅立叶变换红外光谱(FTIR)、傅立叶变换拉曼光谱(FT-Raman)及电子自旋共振(ESR)分析. 振动光谱显示在处理后的膜中存在共轭碳碳双键. 首次用ESR检测到碱处理后的PVDF膜中形成了自由基, 其浓度在10¹⁶ spin/g. 研究表明碱处理引起的膜结构变化有利于接枝反应的进行, 对提高所合成的质子交换膜的电导率有重要作用, 电导率提高一个数量级, 至6.40×10^－2 S/cm.     

四甲基氢氧化铵改性聚偏氟乙烯一步接枝聚苯乙烯磺酸油水分离膜的制备及性能

利用四甲基氢氧化铵(TMAH)聚偏氟乙烯(PVDF)进行改性,以过氧化苯甲酰(BPO)为引发剂,将苯乙烯磺酸(SSA)接枝到改性的PVDF骨架上,制得聚偏氟乙烯接枝聚苯乙烯磺酸(PSSA-g-PVDF)油水分离膜。 研究了TMAH质量分数对PSSA的接枝率和油水分离膜性能的影响,同时采用傅立叶变换红外光谱(FTIR)、扫描电子显微镜(SEM)和视频光学接触角测量仪测试了膜的结构和表面接触角。 结果表明,TMAH使PVDF脱去部分氟化氢(HF)产生碳碳双键,硫元素均匀地分布在分离膜中。 PSSA的接枝率随着TMAH的质量分数增加而升高,分离膜的水通量随接枝率的升高先增加后降低。 当TMAH质量分数为20%,分离膜的接触角在30 s内降低到37.2°,接枝率和水通量分别为22.1%、643.3 L/(m·h),截留率和水通量恢复率分别达到90.6%和93.7%,衰减率为7.1%。 循环测试显示膜的水通量恢复率和油水通量恢复率均在90%以上。     

改性聚偏氟乙烯接枝共混聚苯乙烯磺酸膜的制备与性能

将苯乙烯添加到溶有原硅酸钠改性的聚偏氟乙烯(PVDF)N-甲基吡咯烷酮溶液中, 以过氧化苯甲酰(BPO)作引发剂, 苯乙烯直接接枝到原硅酸钠改性的PVDF链上, 成膜后磺化制备了聚偏氟乙烯接枝苯乙烯(PVDF-g-PSSA)膜. 采用傅立叶变换红外光谱(FT-IR)、扫描电镜(SEM)、能量扩散X射线(EDX)和多功能材料实验机表征了膜的结构、形貌及硫和硅的分布、机械强度、溶胀度, 使用阻抗分析和气相色谱仪研究了苯乙烯含量(w)对PVDF-g-PSSA膜的质子导电性能和阻醇性能的影响. 结果表明, 苯乙烯加入后, 原硅酸钠改性的PVDF与苯乙烯进行接枝共聚反应, 苯乙烯磺化反应不只是在膜表面进行, 同时渗入到膜中进行, 机械性能得到了改善. 质子电导率(σ)随苯乙烯质量分数的提高而升高. Na4SiO4为8%和苯乙烯为20%的PVDF-g-PSSA膜, 在25 ℃时溶胀度仅为20.4%, 甲醇透过系数在10-7 cm2·s-1数量级上, 比Nafion115膜的低一个数量级. 该膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.     

掺杂纳米SiO2的PVDF-g-PSSA质子交换膜

以聚偏氟乙烯(PVDF)为骨架, 采用溶液接枝苯乙烯磺酸, 合成了掺杂纳米SiO₂颗粒的复合质子交换膜(PVDF/xSiO₂-g-PSSA). 利用红外光谱、热失重分析方法、扫描电镜, 对膜的结构、热稳定性、表面及断面形态进行了表征. 考察了膜的吸水率、电导率、甲醇渗透性等性质. 结果表明, 纳米SiO₂颗粒能提高膜的阻醇性能, 掺杂质量分数10%的适量SiO₂颗粒所得的复合膜的甲醇渗透系数达1.0×10^－7 cm²/s, 低于聚偏氟乙烯接枝苯乙烯磺酸(PVDF-g-PSSA)膜的1.7×10^－7 cm²/s, 仅为Nafion-117的渗透系数的二十分之一. PVDF/10% SiO₂-g-PSSA复合膜具有较高的选择性, 在直接甲醇燃料电池中具有良好的应用前景.     

改性聚偏氟乙烯接枝磺化聚(苯乙烯-co-丙烯酸)膜的研制

以过氧化苯甲酰(BPO)作引发剂,通过溶液接枝聚合法把苯乙烯/丙烯酸同时接枝到原硅酸钠改性的聚偏氟乙烯(PVDF)膜上,磺化后得到聚偏氟乙烯接枝磺化聚(苯乙烯-co-丙烯酸)膜(PVDF-g-P(SSA-co-AA)).研究了苯乙烯和丙烯酸的不同比例对膜的接枝反应及其相对湿度对膜电导率和含水量的影响.用傅立叶变换红外光谱(FTIR)检测原硅酸钠改性的PVDF膜经过接枝和磺化后所发生的结构变化,并用扫描电镜(SEM)观察PVDF膜接枝前后的形貌以及接枝磺化后产物PVDF-g-P(SSA-co-AA)膜的形貌及硫和硅分布.结果表明,原硅酸钠改性的PVDF膜与苯乙烯/丙烯酸同时发生接枝聚合反应,环境的相对湿度在20%～80%范围,对添加10wt%Na4SiO4的PVDF-g-P(SSA-co-AA)膜的电导率的影响基本不变,并达到0.0198S·cm-1.原硅酸钠改性的PVDF膜结构在接枝前后和磺化前后发生变化,确认磺化反应不只是在膜表面,同时渗入膜中进行.     

聚偏氟乙烯接枝甲基丙烯酸甲酯油水分离膜的研究

使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF),以过氧化苯甲酰(BPO)为引发剂,将甲基丙烯酸甲酯(MMA)接枝到改性PVDF骨架上,合成聚偏氟乙烯接枝聚甲基丙烯酸甲酯(PVDF-gPMMA)共聚物,通过浸没沉淀法制备PVDF-g-PMMA亲水性油水分离膜.通过傅里叶红外光谱(FTIR)、扫描电镜(SEM)和过滤试验分析了膜的结构和性能.同时研究了TEAH浓度和改性时间对PVDF-g-PMMA膜表面接触角的影响.结果表明,TEAH使PVDF脱去HF产生碳碳双键且MMA成功接枝到改性的PVDF骨架上,膜内外孔隙分布均匀;PVDF-g-PMMA膜的接触角随着TEAH浓度的增加、改性时间的加长而减小.TEAH浓度为2.0 wt%,改性20 min制备的PVDF-g-PMMA膜,接枝率为27.1%,孔隙度为71.6%,平均孔径为78.9 nm,接触角降至55.9°,且在50 s内降为0;纯水通量提高到665.34 L/(m2·h),截留率和水通量恢复率分别达到95.6%和90.1%.与纯PVDF膜相比,PVDF-g-PMMA膜的分离性能显著提高.     

Ba0.6Sr0.4TiO3/聚偏氟乙烯-聚甲基丙烯酸甲酯复合材料的制备及其介电性能

采用流延热压工艺制备Ba_0.6Sr_0.4TiO₃(BST)/聚偏氟乙烯(PVDF)?聚甲基丙烯酸甲酯(PMMA)复合薄膜,研究了PMMA含量对复合材料微观组织结构和介电性能的影响规律。结果表明,BST相能够均匀分散在聚合物基体中,归因于PMMA与PVDF良好的相容性,2种聚合物之间的界面不分明;随着PMMA含量的增加,复合材料的介电常数先降低后升高,耐击穿强度和介电可调性先增加后减少。PMMA含量(体积分数)为15%的BST/PVDF?PMMA₁₅复合材料的综合性能最佳:介电常数为23.2,介电损耗为0.07,耐击穿强度为1412 kV·cm^-1,在550 kV·cm^-1偏压场下,介电可调性为26.2%。     

四乙基氢氧化铵改性聚偏氟乙烯接枝聚丙烯酸油水分离膜的制备

使用四乙基氢氧化铵(TEAH)液相本体改性聚偏氟乙烯(PVDF), 以过氧化苯甲酰(BPO)为引发剂, 将丙烯酸(AA)接枝到改性PVDF骨架上, 合成了聚偏氟乙烯接枝聚丙烯酸(PVDF-g-PAA)共聚物, 通过浸没沉淀法制备了PVDF-g-PAA亲水性油水分离膜. 通过傅里叶变换红外光谱(FTIR)、 扫描电子显微镜(SEM)和过滤试验分析了膜的结构和分离性能. 研究了不同接枝条件对PVDF-g-PAA膜接枝率的影响. 同时, 通过膜接枝率与膜表面接触角的关系确定最佳接枝条件. 结果表明, TEAH使PVDF脱去HF产生碳碳双键且PAA接枝到改性的PVDF骨架上, 膜内外孔隙分布均匀; PVDF-g-PAA膜的接触角随着接枝率的提高而降低. 接枝单体AA含量为45%, 接枝温度为85 ℃, 接枝4 h制备的PVDF-g-PAA膜的接枝率为20.1%, 孔隙度为65.3%, 平均孔径为78.0 nm, 接触角为57.5°, 且在60 s内接触角降至14.3°; 纯水通量提高到571.33 L/(m²·h), 截留率和水通量恢复率分别达到94.3%和88.7%, 且通量衰减率仅为9.8%. 与纯PVDF膜相比, PVDF-g-PAA膜的分离性能显著提高.     

表面引发的原子转移自由基聚合法在聚偏二氟乙烯表面制备可控的聚甲基丙烯酸甲酯刷

采用表面引发的原子转移自由基聚合法(ATRP)在聚偏二氟乙烯(PVDF)表面制备结构可控的聚甲基丙烯酸甲酯刷。通过碱处理和紫外光照溴代的方法,将ATRP引入到PVDF表面; 然后采用ATRP法将甲基丙烯酸甲酯接枝到溴代的PVDF表面。采用傅里叶变换红外光谱和X-射线光电子能谱对改性前后PVDF表面的结构进行了表征。结果表明甲基丙烯酸甲酯成功地接枝到了PVDF表面。     

SPES/PWA/SiO_2复合质子交换膜的性能

以磺化聚醚砜(SPES)为基体,以不同比例的SiO2溶胶与磷钨酸(PWA)为掺杂物,制备了一种有望用于直接甲醇燃料电池(DMFC)的新型SPES/PWA/SiO2有机-无机复合膜,并经热失重分析(TGA)、差示扫描量热仪(DSC)、扫描电镜(SEM)-X射线能谱分析(EDX)等对膜的结构和性能进行了表征,探讨了复合膜用作质子交换膜的可能性.结果表明:复合膜较纯SPES膜具有更高的热稳定性、玻璃化转变温度和吸水率;虽然在室温和电池操作温度(80℃)下,复合膜的拉伸强度均低于纯SPES膜,但即使当SiO2含量高达20%(w)时,复合膜的拉伸强度仍高于Nafion112膜的;SEM图片显示SiO2和PWA在膜中分布均匀,这将有利于连续质子传输通道的形成.对于SiO2含量为15%(w),PWA含量为6%(w)的复合膜,其室温质子传导率达到了0.034S·cm-1,与Nafion112膜的相当,但其甲醇渗透率明显降低,仅为商用Nafion112膜的七分之一左右,这表明该复合膜在直接甲醇燃料电池中具有良好的应用前景.     

Synthesis and Characterization of Novel Sulfonated Polyimides from 4,6-Bis（4-aminophenoxy）-naphthalene-2-sulfonic Acid

A novel sulfonated diamine monomer, 4,6-bis（4-arninophenoxy）-naphthalene-2-sulfonic acid（BAPNS）, was synthesized. A series of sulfonated polyimide copolymers was prepared from BAPNS, 1,4,5,8-naphthalenetetracarboxylic dianhydride（NTDA） and nonsulfonated diamine 4,4＇-diaminodiphenyl ether（ODA）. Flexible, transparent, and mechanically strong membranes were obtained. The novel sulfonated polyimide（SPI） membranes show higher conductivity, for example, SPI-100 shows a conductivity of 0.0698 S/cm at 80℃（SPI-X： Xrefers to molar fraction of BAPNS）. The membranes exhibit the permeability of methanol from 2.18×10^-7 cm2/s to 2.57×10^-7 cm2/s, which is much lower than that of Nafion（2.00×10 6 cm^2/s）. The copolymers were thermally stable up to 330℃. The sulfonated polyimide copolymers also show reasonable mechanical strength; for example, the maximum tensile strength at break of the sulfonated polyimide copolymer with 100%（molar fraction） BAPNS is 1.35 GPa under high moisture condi- tions. The optimum concentration of BAPNS was found to be 100%（molar fraction） from the view point of proton conductivity, methanol permeability, and membrane stability.     

全钒液流电池的隔膜研究与应用

研究全钒液流电池的质子传导膜制备过程,提出高分子亲水/疏水相互作用诱导溶液相分离的成膜原理,进行制膜工艺放大,满足全钒液流电池的电堆制造与储能工程应用需要. 突破现有“离子交换”传质机理的限制,利用电解液中不同价态钒离子与氢离子相比,存在体积和荷电量的差异,通过离子“筛分”和“静电排斥”效应进行离子选择性渗透. 制成孔径分布在4 ~ 7 nm的聚偏氟乙烯质子传导膜,电导率为3.5×10-2 S•cm^-1,爆破强度高于0.3 MPa,面积800 mm × 900 mm. 利用扩散实验测定膜对H⁺/VO²⁺离子选择性,选择性系数达到306. 利用该质子传导膜组装的15 kW电堆,充电/放电循环性能稳定,电流密度达到100 mA•cm^-2,在700多个循环过程电流效率为93%,能量效率超过72%,具备产业化应用前景.     

Embedded polymerization driven asymmetric PEM for direct methanol fuel cells

This work reports the fabrication of proton exchange membranes (PEM) with stronger resistance to methanol penetration than Nafion^®117. A three-component acrylic polymer blend (TCPB) consisting of a copolymer of 4-vinylphenol-methyl methacrylate, poly(butyl methacrylate) (PBMA) and a copolymer of methyl methacrylate-ethyl acrylate is used as the methanol barrier. In order to implant a proton source phase within the membrane as homogeneously as possible, the hydrophilic monomers, 2-acrylamido-2-methyl propanesulfonic acid (AMPS), 2-hydroxyethyl methacrylate (HEMA) and poly(ethylene glycol) dimethylacrylate (PEGDMA), are polymerized only after they have been embedded in the TCPB matrix. The embedded polymerization has resulted in an asymmetric membrane structure, in which the hydrophilic network is sandwiched by two layers of matrixes with high percentages of TCPB. As expected, this asymmetric membrane structure exhibits lower methanol uptake than Nafion^®117; and a proton conductivity in the range of 10⁻³–10⁻⁴ S/cm, which is dependent on the concentration of the sulfonic acid content. It is suggested that the two external layers in this asymmetric membrane provide primarily methanol-blocking and supporting proton-conducting properties; while the middle layer supplies protons and conserves water. This unique sandwiched PEM structure from embedded polymerization is confirmed by microstructure characterizations and by physical property measurements.     

基于磷钨酸功能化纳米纤维的超高质子/钒选择性的聚苯并咪唑膜在全钒液流电池中的应用

Proton exchange membrane (PEM) is a key component of vanadium redox flow battery (VRB), and its proton/vanadium selectivity plays an important role in the performance of a VRB single cell. Commercially available perfluorosulfonic acid (Nafion) membranes have been widely used due to their excellent proton conductivity and favorable chemical resistance. However, the large pore size micelle channels formed by the pendant sulfonic acid groups lead to the excessive penetration of vanadium ions, which seriously affects the coulombic efficiency (CE) of the single cell and accelerates the self-discharge rate of the battery. Additionally, the expensive cost of Nafion is also an important reason to limit its large-scale application. In this paper, the dense and low-cost hydrocarbon polymer polybenzimidazole (PBI) is used as the matrix material of the PEM, which is doped with phosphotungstic acid (PWA) to acquire excellent proton conductivity, and the intrinsic high resistance of PBI for vanadium ions is helpful to obtain high proton/vanadium selectivity. Considering the enormous water solubility of PWA and its easy leaching from membrane, organic polymer nano-Kevlar fibers (NKFs) are utilized as the anchoring agent of PWA, which achieves good anchoring effect and solves the problem of the poor compatibility between inorganic anchoring agent and the polymer matrix. The formation of PWA functionalized NKFs was characterized by scanning electron microscope (SEM) and Fourier transform infrared (FT-IR) spectroscopy. The anchoring stability of NKFs for PWA was evaluated by UV-Vis spectroscopy. The characterizations including water uptake, swelling ratio, ion exchange capacity, proton conductivity, vanadium ion permeability and ion selectivity were performed to evaluate the basic properties of the membranes. At the same time, the charge-discharge, self-discharge and cycle performance of single cell assembled with the composite membrane and recast Nafion were tested at various current densities from 40 to 100 mA∙cm^-2. Simple tuning for the filling amount of NKFs@PWA gives the composite membrane superior ion selectivity including an optimal value of 3.26 × 10⁵ S∙min∙cm^-3, which is 8.5 times higher than that of recast Nafion (0.34 × 10⁵ S∙min∙cm^-3). As a result, the VRB single cell assembled with the composite membrane exhibits higher CE and significantly lower self-discharge rate compared with recast Nafion. Typically, the CE of the VRB based on PBI-(NKFs@PWA)-22.5% membrane is 97.31% at 100 mA∙cm^-2 while the value of recast Nafion is only 90.28%. The open circuit voltage (V_OC) holding time above 0.8 V of the single cell assembled with the composite membrane is 95 h, which is about 2.4 times as long as that of recast Nafion-based VRB. The utilization of PBI as a separator for VRB can effectively suppress the penetration of vanadium ions, achieve higher proton/vanadium selectivity and superior battery performance as well as reduce the cost of the PEM, which will play an active role in the promotion of VRB applications.     

磺化聚芳醚酮砜/聚芳醚砜噁二唑复合型质子交换膜的制备与性能

为了降低质子交换膜(PEM)的甲醇渗透系数和改善PEM在中高温(80~120 ℃)时的质子传导率, 以自制的磺化度(SD)为100%的磺化聚芳醚酮砜(SPAEKS)与聚芳醚砜噁二唑(PAESO)为原料, 采用溶液共混法制备了SPAEKS/PAESO复合膜, 并用傅里叶变换红外光谱(FTIR)和热重分析(TGA)对其进行了表征. 结果表明, 该复合膜具有较好的化学稳定性和热稳定性. 扫描电子显微镜(SEM)照片显示, 复合膜具有较好的致密结构, 其甲醇渗透系数为3.9×10^-7~6.6×10^-7 cm²/s, 低于SPAEKS的8.7×10^-7 cm²/s. 在100 ℃时复合膜的质子传导率达到0.074 S/cm, 高于SPAEKS膜的0.066 S/cm.     

聚苯并咪唑/聚乙烯吡咯烷酮复合质子交换膜的制备及钒液流电池性能

将聚苯并咪唑(PBI)与聚乙烯吡咯烷酮(PVP)共混, 制备了一系列PBI/PVP复合质子交换膜, 研究了不同PVP含量对PBI/PVP复合质子交换膜性能的影响. 研究结果表明, PVP的加入可有效提高PBI/PVP复合质子交换膜的吸水率及硫酸吸附量, 从而提高质子电导率, 与PBI原膜相比, PBI-PVP-5复合质子交换膜的结合酸含量可达2.47 mmol/g, 质子电导率达4.81 mS/cm, 选择性(3.12×10⁵ S·min/cm³)远高于原膜(1.12×10⁵ S·min/cm³). 电流密度为120 mA/cm²时, 电池的电压效率(VE)和能量效率(EE)均较PBI原膜提高了10%, 电池自放电时间长达307 h. PVP的加入为PBI系列钒液流电池隔膜提供了一个提高质子电导率的新思路.     

填充型具有微孔结构的磺化聚芳醚砜/聚醚砜复合质子交换膜的制备及性能

制备了基于磺化聚芳醚砜(SPAES)及聚醚砜(PES)的填充型复合质子交换膜, 研究了其吸水率、 尺寸变化、 热-机械特性、 质子电导率、 甲醇透过性及稳定性等性能. 通过浸入沉淀相转化法, 采用磺化度分别为30%(S30), 40%(S40)及50%(S50)的SPAES与PES制备了系列微孔型复合质子交换膜 Sx-y(x为SPAES的磺化度, y为SPAES的质量分数); 然后利用真空抽滤法在微孔中填充S50制备了相应的填充型复合质子交换膜Sx-y+F50. 结果表明, 由于微孔的引入及皮层结构的存在, Sx-y膜在低离子交换容量(IEC)条件下仍具有较高的电导率、 优良的机械强度、 优异的化学稳定性及较低的甲醇透过性. 经S50填充后, Sx-y+F50膜的IEC及电导率明显提升, 甲醇透过率大幅下降, 但机械强度及化学稳定性未见劣化. 其中S30-40+F50膜(IEC=0.69 mmol/g)的综合性能最佳, 其质子电导率在90 ℃水中达到50.4 mS/cm; 经140 ℃水处理24 h后失重率仅为8.2%, 质子电导率降低仅9%; 经过芬顿试剂(3% H₂O₂, 20 mg/L FeSO₄, 80 ℃, 1 h)处理后失重率仅为0.66%; 甲醇透过率仅为6.8×10^-8 cm²/s.     

Polymer blend membranes of sulfonated poly(arylene ether ketone) for direct methanol fuel cell

The blend membranes of sulfonated poly(arylene ether ketone) (sPAEK) (IEC = 1.0 mequiv./g)/Nafion^® and the blend membranes of sPAEK (IEC = 1.0 mequiv./g)/sPAEK (IEC = 1.7 mequiv./g) were prepared. sPAEK with low IEC was introduced to reduce the methanol permeability through the membrane. Morphology, water uptake, proton conductivity and methanol permeability of the blend membranes were investigated by SEM, AFM, AC impedance spectroscopy and permeability measuring instrument. The cross-sections of blend membranes showed phase-separated morphologies. The effect of phase-separated morphology on the properties of blend membranes was investigated. The properties like water uptake, proton conductivity, and methanol permeability of sPAEK/Nafion^® blend membranes showed similar values with sPAEK and properties of sPAEK/sPAEK blend membranes showed intermediate values of two polymers due to the difference in morphology of the blend membranes. sPAEK/sPAEK blend membranes showed relatively high proton conductivity and lowered methanol permeability compared to Nafion^®. sPAEK/sPAEK blend membranes could be a competent substitution for Nafion^®.