Thermal degradation and their kinetics of biodegradable poly(butylene succinate-co-butylene terephthate)s under nitrogen and air atmospheres

In this study, thermal degradation and their related kinetics have been investigated mainly by means of thermal gravimetrical analyzer (TGA) under the dynamic nitrogen and air atmospheres for the chemically prepared biodegradable aliphatic-aromatic copolyesters of poly(butylene succinate-co-butylene terephthalate) (PBST). To further shed new lights on the comonomer molar composition and experimental condition dependences of thermal degradation kinetics, the as-known Friedman model was at first applied to quantitatively evaluate the kinetic parameters in terms of activation energy (E), degradation reaction order (n) and the frequency factor (Z). The results clearly demonstrated that thermal stabilities of these PBST copolyesters were substantially enhanced with the incorporation of more rigid butylene terephthalate comonomer, and tended to be much better in nitrogen than in air. Furthermore, the Friedman, Freeman-Carroll and Chang models were concurrently employed to quantitatively evaluate the thermal degradation kinetic parameters of the PBST copolyesters in nitrogen at different heating rates of 1, 2 and 5 K/min. It was found that the thermal degradation kinetic parameters for the PBST copolyesters were strongly dependent on the heating rate and calculating models. In addition, life-time parameters of the biodegradable PBST copolyesters were first calculated to predict the maximum usable temperatures, and this would be useful for practical application of these new bio-based green plastics.     

Multiple melting behavior of biodegradable poly(butylene succinate-co-terephthalate) (PBST) copolyester

The multiple melting behavior of biodegradable poly(butylene succinate-co-terephthalate) (PBST) copolyester with 70 mol% aromatic units isothermally crystallized at various temperatures was investigated by wide angle X-ray diffraction, differential scanning calorimetry (DSC) and modulated DSC (MDSC). PBST copolyester exhibited at most three melting peaks in the DSC heating traces and the dual lamellar population model was utilized for interpreting the origin of the multiple melting behavior. Multiple melting peaks were observed even at high heating rates and the co-existence of the melting-recrystallization-remelting model was suggested. The MDSC results gave the direct evidences to the conclusion that the combination of the two models mentioned above was able to explain the multiple melting behavior of PBST copolyester properly.     

Characterization and enzymatic degradation of microbial copolyester P(3HB-co-3HV)s produced by metabolic reaction model-based system

The two types of poly(3-hydroxybutyrate-co-3-hydroxyvalerate)s [P(3HB-co-3HV)s] were produced by Paracoccus denitrificans ATCC 17741 using two different feeding methods. The produced P(3HB-co-3HV)s were fractionated and the copolymer sequence distributions were analyzed by ¹H and ¹³C NMR spectroscopy. It was found that the P(3HB-co-3HV) samples produced by conventional feeding method were statistically random copolymers. The sequence distributions of P(3HB-co-3HV) samples produced by optimization method were different from random P(3HB-co-3HV)s. The thermal properties and melting behaviors were analyzed by differential scanning calorimetry (DSC). These results demonstrated that P(3HB-co-3HV) samples produced by optimization method are close in nature to P(3HB-co-3HV)s rich in long-sequence of block 3HB units, but less in 3HV random regions. The enzymatic degradation profile of P(3HB-co-3HV) films was investigated in the presence of 3-hydroxybutyrate depolymerase from Pseudomonase lemoignei. The degradation process was observed by monitoring the time-dependent change in the weight loss of copolymer films. The surface erosion of copolymer films was qualitatively monitored by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The highest degradation rate of 2.6% per day was observed for random P(3HB-co-38%3HV) produced by conventional method. In comparison, the hydrolysis degradation rates of random P(3HB-co-3HV)s were about one time faster than those of P(3HB-co-3HV)s produced by optimization method.     

Fungal degradation of poly(ethylene succinate)

Twenty fungi, which all formed a clear zone around the colony on a poly(ethylene succinate) (PESu)-containing medium, were isolated from various environmental samples. Mesophilic strain NKCM1003, with the highest PESu hydrolytic activity among all the isolates, degraded a PESu film at the rate of 21 ± 2 μg/cm²/h when it was aerobically incubated at 30 °C on a medium containing PESu as the sole carbon source. SEM observations showed that the strain gradually degraded the film starting from the amorphous regions of the surface. Phylogenetic analysis revealed that the strain was closely related to the species Aspergillus clavatus. Zymogram analysis suggested that the secreted enzyme with PESu hydrolytic activity is a P(3HB) depolymerase. The strain also utilized the enzymatic products of PESu, permitting it to grow well. These results indicate that the strain NKCM1003 plays an important role in the PESu-degrading process in the field.     

Electrochemical synthesis and investigation of poly(1,4-bis(2-(3,4-ethylenedioxy)thienyl)benzene) and its application in an electrochromic device

1,4-Bis(2-(3,4-ethylenedioxy)thienyl)benzene, prepared by Stille cross-coupling reaction was successfully electrochemically polymerized to give polymer 1,4-bis(2-(3,4-ethylenedioxy)thienyl)benzene (PEBE). Characterizations of the resulting polymer PEBE were performed by cyclic voltammetry (CV), UV–vis, Fourier transform infrared spectroscopy and scanning electron microscopy. Moreover, the spectroelectrochemical and electrochromic properties of the polymer film were investigated. The resulting polymer film has distinct electrochromic properties and shows three different colors (deep red, gray, and light blue) under various potentials. At the dedoped state of the polymer, the π–π* transition absorption peak is located at 510?nm and the optical band gap (E _g) was calculated as 1.92?eV. The PEBE film shows a maximum optical contrast (ΔT%) of 31.0?% at 500?nm with a response time of 0.85?s. The coloration efficiency of PEBE film was calculated to be 182.2?cm²C^?1. An electrochromic device (ECD) based on PEBE and poly(3,4-ethylenedioxythiophene) was also constructed and characterized. The response time was measured as 0.4?s, and the coloration efficiency of the device was calculated to be 225.4?cm²C^?1. Furthermore, this ECD exhibited satisfactory optical memories and redox stability.     

Thermal properties and degradability of poly(propylene carbonate)/poly(β-hydroxybutyrate-co-β-hydroxyvalerate) (PPC/PHBV) blends

Poly(propylene carbonate)/poly(β-hydroxybutyrate-co-β-hydroxyvalerate) (PPC/PHBV) blends were prepared via the solution casting method at different proportions. Their thermal characteristics were studied by means of differential scanning calorimetry (DSC) and thermogravimetry (TG). The degradability of the blends was investigated in soil suspension cultivation and in vitro degradation testing. The changes of structure and molecular weight for blends were also studied by ¹H nuclear magnetic resonance spectroscopy (¹H NMR), scanning electron microscopy (SEM) and gel permeation chromatography (GPC) before and after degradation. Although the PPC/PHBV blends were immiscible, the addition of PHBV could improve the thermal stability of PPC. PHBV was degraded mainly by the action of microbial enzymes in the soil suspension, which biodegraded it more rapidly than PPC in a natural environment. PPC was degraded mainly by chemical hydrolysis and random hydrolytic scission of chains in the PBS solution in vitro, and degradation of PPC was more rapid than that of PHBV in a simulated physiological environment.     

The assessment of miscibility and morphology of poly(ε-caprolactone) and poly(para-chlorostyrene) blends

The miscibility and morphology of poly(ε-caprolactone) (PCl) and poly(para-chlorostyrene) (PpClS) blend were investigated by using thermal analysis, morphological analysis, viscometry, and the study of melting point depression. A single glass transition temperature was observed by differential scanning calorimetry (DSC) for PCl/PpClS blends in the whole compositional range (0/100, 25/75, 50/50, 62.5/37.5, 75/25, 90/10). Morphology of the polymers and their blends was studied by scanning electron microscopy (SEM). The Fourier transform infrared spectra of the samples were obtained by spectrometer. Up to 12 cm⁻¹ shifts in carbonyl stretching band of PCl was detected in the spectra of PpClS rich blends. The viscosity of PCl, PpClS and their blends has also been studied to investigate the miscibility according the miscibility criteria Δb, and Δ[η]. Using this data, the interaction parameters α and μ, based on the Chee and Sun et al. approaches were determined. These criteria indicated that the blend is miscible in all proportions up to 90% of PCl content in the blends. The melting point depression of PCl in the blends was examined to obtain the interaction parameter, χ₁₂ for this system. The parameter, χ₁₂ was found to be composition dependent. Negative values of the obtained interaction parameter also support the miscibility of this system up to the 90% PCl in the blend.     

Probing trace Pb(2+) using electrodeposited N,N'-(o-phenylene)-bis-benzenesulfonamide polymer as a novel selective ion capturing film

A novel film modified electrode for the determination of trace lead was developed in this work. The modified electrode was prepared by the electropolymerization of N,N′-(o-phenylene)-bis-benzenesulfonamide (PBSA) as the ion capturing reagent to create the functional film. The modified electrode shows a high selectivity towards Pb²⁺ over interfering cations, e.g. Cu²⁺, Cd²⁺, Co²⁺, Ni²⁺, Zn²⁺, Cr²⁺, and the calibration curve was linear in the concentration range of 2.0 × 10⁻⁹ to 1.0 × 10⁻⁷ M with correlation coefficient of 0.999. For 20 min accumulation, detection limit of 1.0 × 10⁻⁹ M was obtained at the signal to noise ratio of 3. Analytical availability of the modified electrode was demonstrated by the application for samples from pond water.     

Synthesis and applications of surface-grafted Th(IV)-imprinted polymers for selective solid-phase extraction of thorium(IV)

A new functional monomer N-(o-carboxyphenyl)maleamic acid (CPMA) was synthesized and chosen for the preparation of surface-grafted ion-imprinted polymers (IIPs) specific for thorium(IV). Polymerizable double bond was introduced to silica gel surface by amidation reaction between -NH₂ and maleic anhydride. In the ion-imprinting process, thorium(IV) was complexed with the carboxyl groups, then was imprinted in the polymers grafted to the silica gel surface. The imprinted Th(IV) was removed with 3 mol L⁻¹ HCl. The obtained imprinted particles exhibited excellent selectivity and rapid kinetics process for Th(IV). The relatively selective factor (α_r) values of Th(IV)/La(III), Th(IV)/Ce(III), Th(IV)/Nd(III), Th(IV)/U(VI), and Th(IV)/Zr(IV) were 85.7, 88.9, 26.6, 64.4, and 433.8, respectively, which were greater than 1. The precision (R.S.D.), the detection limit (3σ), and the quantification limit (10σ) of the method were 1.9%, 0.51 ng mL⁻¹ and 1.19 ng mL⁻¹, respectively. The prepared IIPs as solid-phase extractants were successfully applied for the preconcentration of trace thorium in natural and certified samples prior to its determination by inductively coupled plasma atomic emission spectrometry (ICP-AES) with satisfactory results.     

Biosorption of copper(II), lead(II), iron(III) and cobalt(II) on Bacillus sphaericus-loaded Diaion SP-850 resin

The biosorption of copper(II), lead(II), iron(III) and cobalt(II) on Bacillus sphaericus-loaded Diaion SP-850 resin for preconcentration-separation of them have been investigated. The sorbed analytes on biosorbent were eluted by using 1 mol L⁻¹ HCl and analytes were determined by flame atomic absorption spectrometry. The influences of analytical parameters including amounts of pH, B. sphaericus, sample volume etc. on the quantitative recoveries of analytes were investigated. The effects of alkaline, earth alkaline ions and some metal ions on the retentions of the analytes on the biosorbent were also examined. Separation and preconcentration of Cu, Pb, Fe and Co ions from real samples was achieved quantitatively. The detection limits by 3 sigma for analyte ions were in the range of 0.20-0.75 μg L⁻¹ for aqueous samples and in the range of 2.5-9.4 ng g⁻¹ for solid samples. The validation of the procedure was performed by the analysis of the certified standard reference materials (NRCC-SLRS 4 Riverine Water, SRM 2711 Montana soil and GBW 07605 Tea). The presented method was applied to the determination of analyte ions in green tea, black tea, cultivated mushroom, boiled wheat, rice and soil samples with successfully results.     

New confined p-phenylenevinylene (PPV)-type polymer analogue of poly(phenylene sulfide)

A new confined p-phenylenevinylene (PPV)-type polymer (PPVS) has been synthesized using Wittig condensation. The chemical structure of the polymer was well defined by ¹H NMR, ¹³C NMR, and FTIR spectroscopic analysis. PPVS contains oligomeric PPV units separated by sulfide bridges in the main chain; it is fully soluble in common organic solvents and has a number-average molecular weight of 3500 g mol⁻¹. Thermogravimetric analysis and differential scanning calorimetry indicate that PPVS is amorphous, stable up to 360 °C in air and displays a glass transition temperature of 98 °C. The optical properties of the polymer were investigated by UV-visible absorption and photoluminescence spectroscopies. The polymer film absorbs at 375 nm and emits at 517 nm with a narrow emission spectrum. From the cyclic voltammetry analysis, the electrochemical bandgap was estimated to be 2.78 eV. A single-layer diode device of the configuration indium-tin oxide/PPVS/aluminium has been fabricated and has a relatively low turn-on voltage of 3.4 V. An electroluminescent emission similar to photoluminescence is demonstrated in a multilayer device.     

Effects of comonomer sequential structure on thermal and crystallization behaviors of biodegradable poly(butylene succinate‐co‐butylene terephthalate)s

In this work, new investigations on the effect of comonomer sequential structure on the thermal and crystallization behaviors and biodegradability have been implemented for the biodegradable poly(butylene succinate‐co‐butylene terephthalate) (PBST) as well as aliphatic poly(butylene succinate) (PBS). At first, these copolyesters were efficiently synthesized from dimethyl succinate and/or dimethyl terephthalate and 1,4‐butanediol via condensation polymerization in bulk. Subsequently, their molecular weights and macromolecular chain structures were analyzed by gel permeation chromatography (GPC) and nuclear magnetic resonance (NMR) spectroscopy. By means of differential scanning calorimeter (DSC) and wide‐angle X‐ray diffractometer (WAXD), thermal and crystallization behaviors of these synthesized aromatic–aliphatic copolyesters were further explored. It was demonstrated that the synthesized copolyesters were revealed to have random comonomer sequential structures with thermal and crystallization properties strongly depending on their comonomer molar compositions, and that crystal lattice structures of the new crystallizable copolyesters shifted from the monoclinic crystal of semicrystalline PBS to triclinic lattice of the poly(butylene terephthalate) (PBT) with increasing the terephthalate comonomer composition, and the minor comonomer components were suggested to be trapped in the crystallizable component domains as defects. In addition, the enzymatic degradability was also characterized for the copolyesters film samples. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 1635–1644, 2006     

Isolation and characterization of poly(butylene succinate)-degrading fungi

We isolated 12 poly(butylene succinate) (PBSu)-degrading fungi from various soil environments. Among the isolates, the NKCM1706 strain exhibited the fastest degradation rate for the PBSu film (10.5 μg cm⁻² h⁻¹). Phylogenetic analysis revealed that this strain is closely related to Aspergillus fumigatus (internal transcribed spacer (ITS) identity, 100%). Further, this strain exhibited PBSu-hydrolytic activity in the presence of poly(?-caprolactone) (PCL), PBSu, and poly(butylene succinate-co-adipate) (PBSA). On adding this strain into the soil sample, the PBSu degradation rate accelerated approximately sixfold, suggesting that this strain plays a crucial role in PBSu degradation in actual soil environments. In addition to PBSu, the NKCM1706 strain could degrade PBSA, poly(ethylene succinate) (PESu), poly(3-hydroxybutyrate) (P(3HB)), and PCL.     

Determination of trace Pb(Ⅱ), Cd(Ⅱ) and Zn(Ⅱ) using differential pulse stripping voltammetry without Hg modification

In this work,we reported a simultaneous determination approach for Pb(II),Cd(II)and Zn(II)atμg L 1concentration levels using differential pulse stripping voltammetry on a bismuth film electrode(BiFE).The BiFE could be prepared in situ when the sample solution contained a suitable amount of Bi(NO)3,and its analytical performance was evaluated for the simultaneous determination of Pb(II),Cd(II)and Zn(II)in solutions.The determination limits were found to be 0.19μg L 1for Zn(II),and0.28μg L 1for Pb(II)and Cd(II),with a preconcentration time of 300 s.The BiFE approach was successfully applied to determine Pb(II),Cd(II)and Zn(II)in tea leaf and infusion samples,and the results were in agreement with those obtained using an atomic absorption spectrometry approach.Without Hg usage,the in situ preparation for BiFE supplied a green and acceptability sensitive method for the determination of the heavy metal ions.     

Poly(malachite green) at nafion doped multi-walled carbon nanotube composite film for simple aliphatic alcohols sensor

Conductive composite film which contains nafion (NF) doped multi-walled carbon nanotubes (MWCNTs) along with the incorporation of poly(malachite green) (PMG) has been synthesized on glassy carbon electrode (GCE), gold and indium tin oxide (ITO) electrodes by potentiostatic methods. The presence of MWCNTs in the composite film (MWCNTs-NF-PMG) enhances surface coverage concentration (Γ) of PMG to ≈396%, and increases the electron transfer rate constant (k_s) to ≈305%. Similarly, electrochemical quartz crystal microbalance study reveals the enhancement in the deposition of PMG at MWCNTs-NF film. The surface morphology of the composite film deposited on ITO electrode has been studied using scanning electron microscopy (SEM) and scanning tunneling microscopy (STM). These two techniques reveal that the PMG incorporated on MWCNTs-NF film. The MWCNTs-NF-PMG composite film also exhibits promising enhanced electrocatalytic activity towards the simple aliphatic alcohols such as methanol, ethanol and propanol. The electroanalytical responses of analytes at NF-PMG and MWCNTs-NF-PMG films were measured using both cyclic voltammetry (CV) and differential pulse voltammetry (DPV). From electroanalytical studies, well defined voltammetric peaks have been obtained at MWCNTs-NF-PMG composite film for methanol, ethanol and propanol at Epa = 609, 614 and 602 mV respectively. The sensitivity of MWCNTs-NF-PMG composite film towards methanol, ethanol and propanol in CV technique are 0.59, 0.36 and 0.92 μA mM⁻¹ cm⁻² respectively, which are higher than NF-PMG film. Further, the sensitivity values obtained using DPV are higher than the values obtained using CV technique.     

Poly(N-isopropylacrylamide)/poly[(N-acetylimino)ethylene] thermosensitive block and graft copolymers

Block and graft copolymers with poly(N-isopropylacrylamide) and poly[(N-acetylimino)ethylene] (PNAI) sequences were synthesized via PNAI derivatives (macroinitiators or macromers). The polymerization yields for block copolymers synthesized in ethanol, using the PNAI macroinitiator, were low (<10%), except where photochemical polymerization was applied. By contrast, for the copolymerizations of N-isopropylacrylamide with the PNAI macromers, performed in alcoholic solution, quite high polymerization yields, around 80-90%, were reached. ¹H-NMR and IR spectral and differential scanning calorimeter thermal data confirmed the copolymer formation. Thermosensitivity of the copolymers was investigated by means of turbidimetric technique as a function of their nature, average molecular weight and composition. It was found that the length of the chain of the PNAI macromer and the content in hydrophilic PNAI units of the resulted copolymer affected this behavior.     

Effect of ethylene glycol on the end group structure of poly(3-hydroxybutyrate)

Ralstonia eutropha was cultivated in a culture medium supplemented with ethylene glycol (EG), which is known to act as a chain transfer agent in the production of poly(3-hydroxybutyrate) (PHB). The PHB extracted from the bacterial cells was analyzed by ¹H and ³¹P NMR spectroscopies and matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS). The addition of EG exerted a remarkable influence on the mass of production and molecular weight of PHB, and then was found to result in chain transfer and termination reactions. MALDI-TOF MS of the partially hydrolyzed PHB revealed that either succinate or glutarate combined with the hydroxyl terminals of PHB as polymerization starters. From ³¹P NMR analysis, the carboxyl groups of the succinyls and glutaryls held in the terminals of the isolated PHB were found to be capped with EG, giving the telechelic polyester with hydroxy functionalities. Based on these results, we propose a plausible mechanism of enzymatic polymerization in the microbial PHB synthesis in the presence of EG.     

Degradation of Polyurethane by Aspergillus flavus (ITCC 6051) Isolated from Soil

The present study deals with the isolation of fungi from soil with the ability to degrade polyurethane (PU). A pure fungal isolate was analyzed for its ability to utilize PU as a sole carbon source in shaking culture for 30?days. Incubation of PU with Aspergillus flavus resulted in 60.6% reduction in weight of PU. The scanning electron microscopy and Fourier transform infrared spectroscopy (FTIR) results showed certain changes on the surface of PU film and formation of some new intermediate products after polymer breakdown. Thermogravimetric curves showed changes between the thermal behavior of the samples that were inoculated with A. flavus and control. FTIR spectra showed detectable changes in control and incubated samples, suggesting that degradation occurs, with the decreased intensity of band at 1,715?cm^?1, corresponding to ester linkages. We have identified an extracellular esterase activity which might be responsible for the polyurethanolytic activity.     

Reaction-induced microphase separation in epoxy resin containing polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer

Polystyrene-block-poly(ethylene oxide) alternating multiblock copolymer (PS-alt-PEO) was synthesized with the combination of atom transfer radical polymerization (ATRP) and Huisgen 1,3-dipolar cycloaddition (i.e., click chemistry). The copolymer has been characterized by means of Fourier transform infrared spectroscopy (FTIR), ¹H nuclear magnetic resonance spectroscopy (NMR), gel permeation chromatography (GPC) and differential scanning calorimetry (DSC). The PS-alt-PEO alternating multiblock copolymer was incorporated into epoxy resin to investigate the behavior of reaction-induced microphase separation, which has been compared to the case of the thermosets containing PS-b-PEO diblock copolymer. The morphology of epoxy thermosets containing PS-alt-PEO alternating multiblock copolymer were investigated by means of atomic force microscopy (AFM), and small-angle X-ray scattering (SAXS) and the nanostructures were detected in all the thermosetting blends investigated. In marked contrast to the case of the thermosets containing PS-b-PEO diblock copolymer, the thermosets containing PS-alt-PEO multiblock copolymer displayed disordered nanostructures, which have been interpreted on the basis of the restriction of the alternating multiblock topology of the block on the formation of the nanostructures via reaction-induced microphase separation.     

Amperometric Sensor for Detection of the Reduced Form of Nicotinamide Adenine Dinucleotide Using a Poly(pyronin B) Film Modified Electrode

An electrochemical method for the preparation of poly(pyronin B) film was proposed in this paper. A poly(pyronin B) (poly(PyB)) film modified glassy carbon electrode (GCE) has been fabricated via an electrochemical oxidation procedure and applied to the electrocatalytic oxidation of reduced form of nicotinamide adenine dinucleotide (NADH). The poly(PyB) film modified electrode surface has been characterized by atomic force microscope (AFM), scanning electron microscope (SEM), electrochemical impedance spectroscopy (EIS), UV‐visible absorption spectrophotometry (UV‐vis) and cyclic voltammetry (CV). These studies have been used to investigate the poly(PyB) film, which demonstrates the formation of the polymer film and the excellent electroactivity of poly(PyB) in neutral and even in alkaline media. Due to its potent catalytic effects towards the electrooxidation of NADH at lower potential (0.0 V), poly(PyB) film modified electrode can be used for the selective determination of NADH in real samples because of dopamine, ascorbic acid and uric acid oxidation can be avoided at this potential. The catalytic peak currents are linearly dependent on the concentrations of NADH in the range of 1.0×10^?6 to 5.0×10^?4 mol/L with correlation coefficients of 0.999. The detection limits for NADH is 0.5×10^?6 mol/L. Poly(PyB) modified electrode also shows good stability and reproducibility due to the irreversible attachment of polymer film at GCE surface.