聚氯乙烯树脂的不饱和度和热稳定性的关系

用紫外 可见光谱法表征了不同来源的聚氯乙烯树脂（ＰＶＣ）的热稳定性，用一氯化碘加成法测量了ＰＶＣ的总的双键含量，用红外光谱法测量了ＰＶＣ的孤立双键和共轭双键的相对含量．结果表明，ＰＶＣ在加工期间的初期着色行为和长期热稳定性并不直接相关，前者取决于ＰＶＣ分子链中共轭双键的含量，而后者则和孤立双键的含量有关     

Characterization of Polyene Sequences in Poly(vinyl Chloride)

Some aspects of the formation and propagation of polyene sequences during the thermal degradation of PVC have been discussed. The average polyene sequence length occurring in a suspension polymerized PVC, degraded in nitrogen at 190°C, was determined to ca. 10 units. The results were somewhat dependent on the type of analysis employed. The formation of internal polyene sequences was characterized by three stages. After an initial period, where the number of internal sites remained constant, new sites were rapidly formed. The high rate of formation then gradually decreased with increasing conversion. Degradation mechanisms explaining this behavior were suggested.     

FT-RAMAN SPECTROSCOPIC STUDY OF THE FORMATION OF POLYENES DURING THERMAL DEGRADATION OF POLY(VINYL CHLORIDE) AND POLY (N-VINYL-2-PYRROLIDONE) BLENDS

In situ degradation of poly(vinyl chloride)/poly (N-vinyl-2- pyrrolidone) (PVC/PVP) blends has been studied by Fourier-transform Raman spectroscopy. PVP acts as a destabilizer in the thermal degradation of PVC as manifested by the reduction of temperature for the onset of degradation and the time the polymer is held at a particular temperature for this onset. Increasing the amount of PVP in the blends decreases the dehydrochlorination temperature and time. In blends containing high PVP concentrations, polyene bands dominate over nondegraded PVC bands. Maximum polyene lengths of around 35 were achieved. High PVP ratios and prolonged degradation at higher temperatures resulted in a decrease in mean polyene length due to crosslinking and oxidative scission.     

Heat Degradation of PVC Stabilized by Treatment with Alkylaluminum Compounds

Thermal degradation of PVC treated with alkylaluminum compounds has been studied. Four PVC samples of different molecular weights have been treated with Me₃Al, and Et₃A₁, and the dehydrochlorination rates of the polymers were determined at 190 and 220°C under a nitrogen atmosphere. The alkylaluminum-treated low molecular weight samples show marked increase in thermal stability, i. e., slower rate of dehydrochlorination right from the beginning of degradation, whereas with the higher molecular weight samples stabilization becomes pronounced only after a few percent of dehydrochlorination. The color of R₃Al-treated samples was much lighter (yellowish) than those of controls (dark brown) at 1% HCl loss. The average polyene sequence lengths formed during the early stages of dehydrochlorination are found to be much shorter with RsAl-treated PVC than with virgin samples. It appears as though polyene sequences which arose by zipping- initiation from allylic and/or tertiary chlorine sites are longer than those which form by random initiation along the chain. The autocatalytic (i. e., HC1-catalyzed) dehydrochlorination observed with virgin PVC disappears after treatment with R3A1. The HCl-catalyzed dehydrochlorination is minimized when thin films are used instead of powdery samples, which may be due to higher rates of HC1 diffusion through thin films. Autocatalysis of dehydrochlorination is affected by the concentrations of double bonds and HCl and the length of polyene sequences. Interaction between polyenes and HC1 by hydrogen transfer may lead to the re-initiation of unzipping, thus lengthening the polyene sequences.     

Kinetics of thermal degradation of poly(vinyl chloride)

Extensively studied thermal degradation of polyvinyl chloride (PVC) occurs with formation of free hydrogen chloride and conjugated double bonds absorbing light in visible region. Thermogravimetric monitoring of PVC blends degradation kinetics by the loss of HCl is often complicated by evaporation and degradation of plasticizers and additives. Spectroscopic PVC degradation kinetics monitoring by absorbance of forming conjugated polyenes is specific and should not be affected by plasticizers loss. The kinetics of isothermal degradation monitored by thermal gravimetric analysis in real time was compared with batch data obtained by UV/Visible absorption spectroscopy. Effects of plasticizer on kinetics of polyene formation were examined. Thermal degradation of PVC films plasticized with di-(2-ethylhexyl) phthalate (DEHP) and 1,2,4-benzenedicarboxylic acid, tri-(3-ethylhexyl) ester (TOTM) was monitored by conjugated double bonds light absorption at 350 nm at 160, 180, and 200 °C. Plasticizer-free PVC powder degradation kinetics and that of plasticized films were also obtained thermogravimetrically at temperatures ranging from 160 to 220 °C. Plasticizer-free PVC powder degradation and spectroscopically monitored degradation of plasticized PVC films occurred with the same apparent activation energy of ≈150 kJ mol⁻¹. No difference in degradation kinetics of films plasticized with DEHP and TOTM was detected.     

Thermal degradation of poly(vinyl chloride) synthesized with a titanocene catalyst

PVC was synthesized using a trichloroindenyltitanium-methylaluminoxane catalyst at room temperature, and its degradation was monitored along with a commercial sample at 160, 170 and 180 °C under air or nitrogen atmosphere. The process was followed by HCl evolution, yellowing index, colour formation and thermogravimetric analysis. The produced polymer had a lower molecular weight and higher surface area, compared with a commercial PVC, while ¹H NMR and T_g values show minimal differences between materials. The HCl evolution degradation studies indicate that produced PVC has a lower thermal resistance than commercial PVC, while TGA reveals the opposite behaviour. Yellowing index and colour evaluation give evidence that nitrogen atmosphere and high surface area in produced PVC allow the polyene growth, whereas low surface area and air atmosphere generate shorter polyenes and chromophoric species. Differences in degradation performance are thought to be due to chemical origin, inherent morphology and differences in instrumentation.     

基于热重红外联用分析的PE、PS、PVC热解机理研究

利用TGA-FTIR联用技术考察了PE、PS、PVC三种典型塑料的热解特性。结果表明,热稳定性从弱到强依次为PVC、PS、PE。PE热解反应过程为典型的一段式反应,红外光谱分析结果表明,PE热解过程为无规则断链形式,生成产物成分复杂,且随热解过程而改变,开始以饱和烃基团为主,中后期以烯烃基团为主,同时有少量炔烃;PS热解过程同样为一段式反应,红外光谱显示主要热解产物为苯乙烯单体,说明热解过程主要是苯乙烯的解聚过程;PVC热解过程较为复杂,主要分为脱氯阶段和共轭多烯重构阶段,红外光谱结果表明,产物中有芳香族化合物。脱氯过程和共轭多烯重构、环化过程在时间和空间上有重合,给二噁英类污染物的生成制造了可能。     

Influence of the tacticity on thermal degradation of PVC. IV. Degradation in solution in comparison with degradation at solid state

Four fractions of PVC were obtained by successive extractions with appropriate solvents from PVC samples prepared in bulk at 60, 40, 0, and ?50°C. Then they were carefully characterized, especially as far as stereoregularity is concerned. The samples were submitted to thermal degradation both at solid state and as solutions in dioctyl phthalate. The type of the polyene sequence distribution in degraded samples was determined by both the UV-visible spectroscopy and the number of chain scissions resulting from the ozonization reaction. The degradation rate was proved to rise together with the syndiotactic sequence content in agreement with results in Parts I–III, obtained only with degradation at solid state. On the other hand, The content of the long polyenes relative to that of the short polyenes in the degraded polymers was found to be higher, and the number of chain scissions through ozonization reaction lower, when the syndiotactic sequence content is high. These results enable us to conclude that the actual mechanism of the PVC thermal degradation depends markedly on the tacticity distribution regardless of whether the degradation occurs either at solid state or in solution.     

The main elementary events of degradation and stabilization of PVC

The fundamental aspects of PVC degradation and stabilization are discussed. The primary process of thermal degradation (initiation, zip-elimination of HCl and simultaneous formation of polyene sequences, and termination of unzipping) is reevaluated in the light of results obtained with PVCs containing increased concentrations of labile chlorines. The effect of these defects on thermooxidative stability of the resin is also discussed. It has been shown that results obtained in recent systematic stabilization studies cannot be explained by the widely accepted Frye-Horst mechanism, i.e., substitution of labile chlorines by stabilizers. A new mechanistic proposition, the reversible blocking mechanism, for the stabilization of PVC is presented, and the effect of stabilizing reactions on the main elementary events of thermal and thermooxidative degradation is described in a unified manner.     

The thermal degradation of poly(vinyl acetate) and poly(ethylene-co-vinyl acetate), Part I: Experimental study of the degradation mechanism

The thermal degradation mechanism of poly(vinyl acetate) (PVAc) and poly(ethylene-co-vinyl acetate) (EVA) copolymers was investigated with solid-state NMR, thermogravimetry coupled with mass spectrometry and differential thermal analysis. Between 300 and 400 °C acetic acid is eliminated (deacetylation), leaving a highly unsaturated residue or polyene. The deacetylation of PVAc is autocatalytic. Upon incorporation of ethylene entities into the polymer backbone, autocatalysis disappears. Between 400 and 500 °C, the polyene will degrade further by chain scission reactions in inert conditions or aromatise in an oxidative environment into a char, and oxidised eventually into CO₂ beyond 500 °C.In inert conditions, the deacetylation step as well as the chain scission reaction shows endothermic effects. In an oxidative environment, large exothermal effects are found for each degradation step. This indicates the occurrence of additional oxidation reactions during deacetylation, an important reorganisation of the polyene during char formation and oxidation of the latter into CO₂.     

Correlation of thermal degradation mechanisms: Polyacetylene and vinyl and vinylidene polymers

The thermal degradation of poly(vinyl bromide) (PVB), poly(vinyl chloride) (PVC), poly(vinyl alcohol) (PVA), poly(vinyl acetate) (PVAc), poly(vinyl fluoride) (PVF), poly(vinylidene chloride) (PVC₂), and poly(vinylidene fluoride) (PVF₂) has been studied by direct pyrolysis–mass spectrometry (DP-MS) and flash pyrolysis–gas chromatography–mass spectrometry techniques. Vinyl and vinylidene polymers exhibit two competitive thermal degradation processes: (1) HX elimination with formation of polyene sequences which undergo further moleculaar rearrangements, and (2) main-chain cleavage with formation of halogenated or oxigenated compounds. The overall thermal degradation process depends on the prevailing decomposition reaction in each polymer; therefore, different behaviors are observed. The thermal degradation of polyacetylene (PA) has also been studied and found important for the elucidation of the thermal decomposition mechanism of the title polymers.     

Structure defects and thermal stability of poly(vinyl chloride)

The presence of polyene and peroxide structures in PVC and their contribution to the rate of thermal decomposition were determined using a large number of commercial suspension PVC samples. Two types of PVC having conjugated -C=C-bonds with different reactivity towards dienophiles were found. Polymer samples of the first type react with chlorine, organic phosphites and maleic anhydride under mild conditions whereas the second type PVC under the same conditions reacts only with chlorine. The obtained data show that polyene structures in these two types of PVC are of cis and trans configuration, respectively. It was also demonstrated that the contribution of diene and peroxy groups to the rate of PVC thermal decomposition is greater than the contribution of any other anomalous structures.     

Degradation of PVCs obtained by controlled chemical dehydrochlorination

Thermal and thermo-oxidative degradation of poly(vinyl chloride)s (PVCs) containing increased concentrations of allylic chlorines, PVC(A)s, prepared by controlled chemical dehydrochlorination with potassium-t-butoxide (t-BuOK) have been studied. The introduction of small amounts of internal allylic chlorines into PVC significantly decreases the thermal and thermo-oxidative stability of the resin. A linear relationship exists between the initial rates (V_HCl)₀ of thermal and thermooxidative dehydrochlorination of solid PVC(A)s and the concentration S of internal allylic chlorines. Both the slope and the intercept of the thermo-oxidative (V_HCl)₀ vs. S plot are higher in oxygen than those obtained in nitrogen at the same temperature; this finding is attributed to fast oxidation of polyenes, and to peroxy radicals formed during polyene oxidation, which initiate subsequent HCl loss by attacking normal repeat units in PVC. The extent of HCl loss as a function of time during thermal degradation of PVC(A)s in intert solvent shows a rapid initial phase followed by a slower stationary phase. The first phase is due to dehydrochlorination involving the labile chlorines, while the stationary phase indicates random initiation of HCl loss at normal? CH₂? CHCl? repeat units. Initial rates of HCl loss increase with S, while the rates of HCl loss during the stationary phase are independent of S. The rate constant of initiation of HCl loss at internal allylic chlorines is almost four orders of magnitude higher than that of random initiation; however, the former is still orders of magnitude lower than that of chain propagation. Quantitative analysis of UV-visible spectra of PVC(A)s degraded in solution suggests geometric polyene distribution. The average length of polyenes decreases as the extent of HCl loss increases and reaches a constant value of ca. 3 at ca. 1% HCl loss for all the investigated PVC(A) samples.     

Effects of zinc-based flame retardants on the degradation behaviour of an aerospace epoxy matrix

Flame behaviour is a fundamental requirement for advanced aerospace composites. In this work, a commercial, low-viscosity epoxy system, typically used in liquid infusion composite processes, and its mixtures with three different zinc-based flame retardants (ZB, ZS, ZHS) at different weight percentages has been investigated by cone calorimetry and thermogravimetric analysis.Cone calorimetry has been performed to verify the flame retardancy effects induced by each filler composition. Nevertheless manufacturability issues require the evaluation of the rheological changes induced by filler on the unloaded matrix system. Rheological tests have been, therefore, performed to identify the maximum concentration of filler. Based on these results thermogravimetric tests have been performed to investigate thermal degradation kinetics of selected systems. The feasibility of Kissinger and Flynn-Wall-Ozawa method for the determination of characteristic degradation kinetics parameters has been evaluated and results were analysed. A simplified decomposition model was assumed to analyse epoxy degradation behaviour; it was found that this model gives appreciable matching with experimental TGA curve trend for neat epoxy whereas for the filled compounds additional stages were assume to occur.     

Liquid crystalline and isotropic epoxy thermosets: Mechanism and kinetics of non-isothermal degradation

Thermal non-oxidative degradability of two epoxy thermosets was studied. Investigations were carried out on a non-commercial liquid crystalline structure and its isotropic homologue in order to provide further insight into the mechanism and kinetics of thermal degradation of the proposed systems. The studies were done by thermogravimetric analysis (TGA) and dynamic mechanical analysis (DMA). For the first time the degradation of a liquid crystalline epoxy was studied using an advanced isoconversional kinetic method. The results were used to predict the thermal stability of both types of epoxy networks. GC-MS analysis was applied on evolved gas during degradation to elucidate the degradation mechanism in accordance with the kinetic results. The liquid crystalline structure has a different mechanism of decomposition in comparison with its isotropic homologue. In spite of a higher T_g value, it shows a similar thermal stability but a lower release of degradation compounds.     

Preparation and degradation of head-to-head PVC

The course of the chlorination reaction of cis-1,4-polybutadiene is dependent on the choice of solvent. When methylene chloride is used, a pure addition reaction of chlorine leads to a polymer with the structure of head-to-head, tail-to-tail PVC. The thermal stability of the head-to-head PVC polymer has been studied by thermal volatilization analysis, thermogravimetry, and evolved gas analysis for hydrogen chloride, and the changes in the ultraviolet (UV) spectrum of the polymer during degradation have been investigated. The head-to-head polymer has a lower threshold temperature of degradation than normal PVC, but reaches its maximum rate of degradation at a higher temperature for powder samples of the polymer under programmed heating conditions. Blends of head-to-head PVC with poly(methyl methacrylate) have also been degraded, and the presence of the head-to-head polymers, like that of normal PVC, results in depolymerization of the PMMA as soon as the dehydrochlorination reaction commences. The mechanism of degradation of head-to-head PVC is discussed.     

Cyclopentadienylation of PVC: Characterization and thermal and thermooxidative degradation studies

PVC has been cyclopentadienylated by two conventional basic, LiCp and NaCp, and a new acidic, Me₂CpAl, cyclopentadienylating agent. PVCs treated with basic cyclopentadienylating agents undergo severe random dehydrochlorination and exhibit a significant decrease in thermal and thermooxidative stability. In contrast, according to ozonization and degradation experiments, Me₂CpAl does not cause dehydrochlorination during cyclopentadienylation. The thermal stability of PVC treated with relatively high concentrations of Me₂CpAl and Me₃Al at 25°C markedly increases due to substitution of labile chlorines in PVC with methyl groups. Initial thermal dehydrochlorination behavior of virgin PVC and samples treated with Me₂CpAl at ?30°C are similar. In contrast, thermooxidative stability decreases on Me₂CpAl treatment at ?30°C; this is attributed to ease of oxidation of pendant cyclopentadienyl groups; that is, the formation of peroxy radicals that may initiate dehydrochlorination by attacking unchanged repeat units in PVC. Acceleration of thermal dehydrochlorination disappears and the length of polyene sequences is reduced on Me₂CpAl and Me₃Al treatment. These observations are attributed to differences in rates of protonation-deprotonation; that is, rates of reinitation of zipping of treated and untreated PVCs during thermal degration. The effect of traces of aluminum residues on degradation of modified PVCs, however, cannot be neglected.     

Initiated oxidation of polyenes formed in the thermal degradation of PVC

Polyenes formed in the thermal degradation of PVC are readily oxidized in the liquid phase in the presence of a radical initiator. In pure oxygen at a constant rate of initiation, different length polyenes are consumed by a first-order reaction: the rate of consumption is proportional to the polyene length and to the square root of initiator concentration. Applying the relationships given by the theory of chain reactions, we determined the ratio of the rate constant of chain propagation calculated for one double bond k₂ to the square root of the chain-termination rate constant k₄. The value obtained, which is relatively high in comparison to other unsaturated hydrocarbons, reflects very well the high reactivity of polyenes of the degraded PVC sample towards oxidation. Intramolecular chain propagation steps are also likely to play a role in the oxidation of polyenes.     

Thermal degradation of poly(vinyl chloride)/poly(ethylene oxide) blends: Thermogravimetric analysis

Thermal stability of poly(vinyl chloride)/poly(ethylene oxide) (PVC/PEO) blends has been investigated by thermogravimetric analysis (TGA) in dynamic and isothermal heating regime. PVC/PEO blends were prepared by hot-melt extrusion (HME). According to TG analysis, PEO decomposes in one stage, while PVC and PVC/PEO blends in two degradation stages. In order to evaluate the effect of PEO content on the thermal stability of PVC/PEO blends, different criteria were used. It was found that thermal stability of PVC/PEO blends depends on the blend composition. The interactions of blends components with their degradation products were confirmed. By using multiple heating rate kinetics the activation energies of the PVC/PEO blends thermal degradation were calculated by isoconversional integral Flynn–Wall–Ozawa and differential Friedman method. According to dependence of activation energy on degree of conversion the complexity of degradation processes was determined.     

热稳定剂对PVC紫外光老化过程中微观结构及宏观性能演变的影响

通过UV-Vis、FTIR、DSC、以及色差、力学性能的测试表征,实时追踪分析了在紫外光老化过程中,含Pb、Sn以及Ca-Zn热稳定剂的PVC体系微观结构和宏观性能的演变过程.结果表明,在相同光老化条件下,PVC/Pb、PVC/Sn和PVC/Ca-Zn体系的微观结构变化规律基本一致,过程中主要的化学反应是,大分子吸收光能后,发生脱HCl生成共轭双键的反应、生成羰基的氧化反应、交联反应和降解反应;不同热稳定剂的作用,主要表现在对于微观结构变化的幅度和动力学过程的影响不同.相应地,3种体系的外观色差和力学性能的变化规律也相似,但色差的变化程度和速度以及老化后力学性能的保持率因所含热稳定剂的不同而不同,其中含Sn体系的颜色稳定性最好,含Pb体系的力学性能保持率最高。