Au@SiO2核壳纳米粒子的制备及其表面增强拉曼光谱

采用柠檬酸钠还原氯金酸法制备金溶胶, 以正硅酸乙酯(TEOS)为硅源, 氨水作催化剂, 制备以金为核, 二氧化硅为壳的核壳纳米粒子. 金纳米粒子的粒径可以通过柠檬酸钠和氯金酸的比例控制, 通过调节TEOS的量和反应的时间可以控制二氧化硅壳层的厚度. 以苯硫酚为探针分子研究了核壳结构纳米粒子的表面增强拉曼散射(SERS)效应与二氧化硅壳层厚度之间的关系. 研究结果表明, 金内核电磁场增强效应随着二氧化硅壳层厚度的增加逐渐减弱, 且其衰减速度比具有相同尺度的双金属核壳结构纳米粒子的慢. 此外, 探针分子主要以物理作用吸附在二氧化硅的表面, 可通过洗涤方法将探针分子除去, 从而可使该复合结构基底用于循环SERS分析.     

草莓型PMMA/SiO2有机-无机复合微球的合成与表征

在纳米二氧化硅水分散介质中,借助于正离子单体甲基丙烯酰氧乙基三甲基氯化铵(MTC)与未改性纳米二氧化硅颗粒之间的电荷作用,通过MTC与甲基丙烯酸甲酯(MMA)的自由基共聚合,制备了草莓型的PMMA/SiO2复合微球.整个制备反应过程中,纳米二氧化硅无需表面处理,体系中无需另外加入乳化剂或助乳化剂,微球表面吸附的纳米二氧化硅对颗粒起稳定作用.详细讨论了纳米二氧化硅初始添加量、MTC浓度对复合微球的平均粒径、复合微球中二氧化硅含量及微球形态的影响.动态光散射粒度分布仪(DLS)测得复合微球粒径在180~300 nm之间,热重分析(TGA)表明复合微球中二氧化硅含量介于16.4%~40.8%之间.透射电镜(TEM)显示所得复合微球具有草莓型结构,二氧化硅于表面富集.     

纳米二氧化硅诱导聚氨酯弹性体结晶行为的研究

使用溶剂共混法制备了热塑性聚氨酯弹性体/纳米二氧化硅复合材料,采用多种实验技术阐明了纳米二氧化硅诱导聚氨酯弹性体中软段结晶的微观机理.TEM表明纳米二氧化硅在聚氨酯弹性体中有很好的分散性,DSC实验发现高温退火后等温结晶处理的聚氨酯纳米复合材料中软段的结晶性和玻璃化转变温度显著提高,纳米二氧化硅的加入量影响玻璃化转变温度和熔融焓最终的平衡值以及它们的增长速率.固体NMR实验发现退火后复合材料中的软段分子运动受到限制,而硬段的链运动明显提高.上述实验结果表明硬段链间的氢键在高温下被破坏,在退火过程中纳米二氧化硅与硬段间的相互作用使得硬段链运动增强,进而促进了与硬段相连的软段结晶能力的提高.基于实验结果建立了聚氨酯/无机纳米复合材料在高温退火和低温等温结晶处理下微观结构和动力学演化的物理模型.     

喷涂法构筑二氧化硅纳米粒子涂层及其光学和润湿性质

采用Stöber方法,通过调节反应温度及乙醇和水的体积,合成了不同粒径的二氧化硅纳米粒子.以合成的粒径为20 nm的二氧化硅纳米粒子为原料,采用简单、方便的喷涂方法在玻璃片上构筑了纳米粒子涂层.在550 ℃煅烧二氧化硅纳米粒子涂层,增强了二氧化硅纳米粒子在玻璃片上的附着力.用1H, 1H, 2H, 2H-全氟辛基三乙氧基硅烷修饰之后,二氧化硅纳米粒子涂层的表面润湿性由亲水性转变为疏水性.通过喷涂法制备的二氧化硅纳米粒子涂层具有减反增透效果,当二氧化硅纳米粒子质量分数为0.48%、循环喷涂沉积数为3时,涂层在可见光范围内的最大透光率可达95.5%.用扫描电子显微镜观测涂层表面形貌发现,喷涂法制备的涂层是均匀的、可控的.喷涂技术构筑纳米粒子涂层具有简单快速、可大面积应用等优点.     

信号肽功能化二氧化硅纳米颗粒的线粒体靶向作用研究

以N-(p-Maleimidophenyl)isocyanate(PMPI)为交联剂, 将线粒体信号肽分子共价修饰到二氧化硅荧光纳米颗粒表面, 构建线粒体信号肽功能化二氧化硅荧光纳米颗粒. 采用荧光分光光度计、Zeta电位仪以及透射电子显微镜对修饰前后的二氧化硅纳米颗粒进行了表征. 结果表明, 信号肽可被成功修饰在纳米颗粒表面, 并且纳米颗粒粒径在信号肽分子修饰前后没有发生明显变化. 以分离纯化的细胞核作为对照, 采用流式细胞术考察了信号肽功能化二氧化硅荧光纳米颗粒与分离纯化后的线粒体的相互作用. 结果表明, 线粒体信号肽修饰到二氧化硅纳米颗粒表面后依然保持良好的生物活性, 能够介导二氧化硅纳米颗粒特异性识别及结合分离纯化的线粒体, 从而为线粒体监测及其功能调控研究提供了新的思路.     

纳米金掺杂中空微胶囊的制备与表征

将表面含有双键的二氧化硅微粒分散在纳米金和聚乙烯吡咯烷酮溶液中.在此溶液中以聚乙烯吡咯烷酮为模板聚合物进行丙烯酸的模板聚合,得到二氧化硅为核、聚丙烯酸/聚乙烯吡咯烷酮/纳米金为壳层的核壳结构微粒.用氢氟酸将二氧化硅微粒去除后,得到了纳米金粒子掺杂的微胶囊.分别用扫描电子显微镜和激光共聚焦显微镜表征了微胶囊在干态和湿态下的形貌.通过电子衍射和透射电子显微镜确证了纳米金粒子在微囊壁上的存在和分布.     

纳米二氧化硅的制备及其在橡胶中的应用研究进展

二氧化硅是一种重要的无机材料,无毒,对环境无污染,具有非常广泛的用途.近年来已经有大量文献报道了纳米二氧化硅的制备及其应用.本文综述了国内外相关文献,介绍了纳米二氧化硅的几种制备工艺,以及在硅橡胶、医用橡胶、轮胎橡胶、日用橡胶制品、胶管胶带和胶鞋中的应用,并展望了纳米二氧化硅的发展方向和应用前景.     

巯丙基功能化介孔纳米二氧化硅的合成

用三种不同的方法将巯基丙基三甲氧基硅烷(MPTMS)引入二氧化硅网络中, 合成了粒径为50-200 nm的巯丙基功能化的介孔纳米二氧化硅, 并利用透射电子显微镜, 热重分析等手段对其形貌与性能进行了表征. 在巯丙基官能团的作用下介孔纳米二氧化硅的形貌发生了重大改变, 由非常规则的六角形变为纳米棒. 控制反应时间可以调节介孔纳米二氧化硅的粒径大小, 用三乙醇胺代替氢氧化钠可以合成直径在100 nm以下的功能化介孔二氧化硅粒子. 为了保护巯基官能团, 选用了酸醇提取法去除模板. 另外, 对介孔二氧化硅粒子的形成机制也进行了探讨.     

Study of the interaction between daunorubicin and human serum albumin,and the determination of daunorubicin in blood serum samples

The interactions between daunorubicin and human serum albumin (HSA) were studied using the spectrofluorimetric method. The binding constants of daunorubicin with HSA were obtained at different temperatures. The effects of various metal ions on the binding constants of daunorubicin with HSA were also studied. The optimum conditions of fluorometric determination of daunorubicin were studied and the developed method was successfully applied to the determination of daunorubicin in serum samples.     

Synthesis of ultrafine refractory oxides zirconia-hafnia-yttria by sol-gel technology

A transparent gel was prepared using a hydrolytically active solution of zirconium, hafnium, and yttrium alkoxoacetylacetonates. This gel served to synthesize ultrafine zirconia-hafnia-yttria complex oxide. The product dispersity was studied as affected by the parameters of xerogel heat treatment. The thermal behavior of the xerogel was studied by DSC-TGA. Elemental analysis (laser mass spectrometry) and phase analysis of the synthesized materials were carried out. Average crystallite sizes were calculated by the Scherrer relationship. The particle morphology was studied by TEM. Specific surface areas were determined. Sintering of ultrafine oxide powders was studied at 1000, 1200, and 1400°C.     

Foaming in aqueous solutions of hexadecyltrimethylammonium bromide and silica nanoparticles: Measurement and analysis of rheological and interfacial properties

The properties of aqueous foams stabilized by a mixture of negatively charged silica nanoparticles and hexadecyltrimethylammonium bromide were studied in this work. Rheological properties of the foams were studied. The interaction between nanoparticles and surfactant molecules in the bulk phase was studied by zeta potential and size measurements of the particles. The interaction at the interface was studied by means of interfacial shear rheology, surface pressure measurement, and atomic force microscopy. It was found that foams were more stable at low surfactant concentrations, though the foamability was low. This was due to the formation of a strong viscoelastic film of surfactant-laden particles at the air–water interface. A suitable mechanism has been proposed to explain the stability of foams in the presence of nanoparticles at different surfactant concentrations.     

Thermal characteristics of the combustion process of biomass and sewage sludge

The combustion of two kinds of biomass and sewage sludge was studied. The biomass fuels were wood biomass (pellets) and agriculture biomass (oat). The sewage sludge came from waste water treatment plant. The biomass and sludge percentage in blends with coal were 10 %. The studied materials were characterised in terms of their proximate and ultimate analysis and calorific value. The composition of the ash of the studied fuels was also carried out. The behaviour of studied fuels was investigated by thermogravimetric analysis (TG, DTG and DTA). The samples were heated from an ambient temperature up to 1,000 °C at a constant three rates: 10, 40 and 100 °C min^?1 in 40 mL min^?1 air flow. TG, DTG and DTA analysis showed differences between coal, biomass fuels and sewage sludge. 10 % addition of studied fuels to the mixture with coal changed its combustion profile in the case of sewage sludge addition. The combustion characteristics of fuel mixtures showed, respectively, qualitative summarise behaviour based on single fuels. Evolved gaseous products from the decomposition of studied samples were identified. This study showed that thermogravimetric analysis connected with mass spectrometry is useful techniques to investigate the combustion and co-combustion of biomass fuels, and sewage sludge, together with coal. Non-isothermal kinetic analysis was used to evaluate the Arrhenius activation energy and the pre-exponential factor. The kinetic parameters were calculated using Kissinger–Akahira–Sunose model.     

Spectroscopic (FT-IR, FT-Raman, UV) and microbiological studies of di-substituted benzoates of alkali metals

The FT-IR, FT-Raman and UV spectra of 3,5-dihydroxybenzoic and 3,5-dichlorobenzoic acids as well as lithium, sodium, potassium, rubidium, caesium 3,5-dihydroxy- and 3,5-dichlorobenzoates were recorded, assigned and compared. The theoretical geometries, Mulliken atomic charges, IR wavenumbers were obtained in B3LYP/6-311++G** level. On the basis of the gathered experimental and theoretical data the effect of metals and substituents on the electronic system of studied compounds were investigated. Moreover, the antimicrobiological activity of studied compounds against two species of bacteria: Bacillus subtilis, Staphylococus aureus and one species of yeast: Candida albicans were studied after 24 and 48 h of incubation. The attempt was made, to find out whether there is any correlation between the first principal component and the degree of growth inhibition exhibited by studied compounds in relation to selected microorganisms.     

Internal energy distribution in electrospray ionization

Internal energies and energy distributions were studied using the 'survival yield' method developed previously. In addition to conventional benzylpyridinium salts, protonated esters (fragmenting by rearrangement) and protonated leucine enkephalin were also used, extending the validity of the technique. Fragmentation processes were studied in the cone voltage region and modeled by the RRKM-based MassKinetics program. The results show that the shapes of the energy distributions are similar to thermal distributions. The mean internal energies are very similar for all compound classes studied, and show a linear increase with collision energy in the 10-50 eV region.     

Korngrößenänderung beim Carburieren von Wolfram und Sintern von Wolframcarbid

The change of grain size during each stage of the process was studied, mainly by optical and electron microscopy. The grain size has a marked effect on the properties of cemented carbide. In order to determine the process of formation of WC powder, the cross section and the surface of the carburized powder were examined microscopically. The mechanisms of carburization and grain growth were clarified. The microstructural relationship between the WC powder and the cemented carbide was also determined. The Co from the ball milled WC-Co mixed powder was extracted and the remaining WC powder was studied microscopically and by determining the grain size distribution. Methods of particle crushing and their effect on differences between various forms of WC powder were studied. Grain growth in sintering and the effect of grain size distribution were also studied. It was concluded that grain growth begins long before the appearance of the liquid phase. Finally it was pointed out that the inner structure of WC should be studied at the atomic level.     

超声波强化提取地骨皮中有机酸的研究

用超声波强化提取地骨皮中有机酸,采用单因素和正交试验方法研究了提取温度、提取时间、料液比、超声波功率对地骨皮中有机酸提取量的影响规律。结果表明超声波提取法的最佳工艺条件为提取温度65℃、提取时间35 min、料液比1∶16、超声波功率135 W,在此条件下地骨皮中总有机酸提取率为2.73%。     

Investigation of ampicillin-cobalt complex and its gamma-radiolysis

Ampicillin-cobalt complex has been investigated spectrophotometrically. The effects of pH and molar ratio of ampicillin to cobalt were studied. The stability constants for the complex formed at different pH values were determined. Gamma-radiolysis of ampicillincobalt complex in aqueous solutions was studied at doses from 20 to 100 Gy, using a¹³⁷Cs source. The variations in UV and IR spectra due to their radiolysis were shown. The results showed an increase in absorbance values with increasing dose and this dependence is linear in the dose range studied. The mechanism of radiation effect on the complex is discussed.     

Determination of thallium by furnace atomic absorption spectrometry

The analytical conditions for the determination of thallium by graphite furnace atomic absorption spectrometry were studied and optimized using the peak-height mode. The charring-atomization curves for thallium from different atomization surfaces were constructed and the optimum charring and atomization conditions were established. These atomization surfaces included pyrolytic graphite-, tantalum-, zirconium- and tungsten-coated graphite tubes. The effects of different inorganic acids on the absorbance of thallium from different surfaces were studied. Using tungsten carbide-coated tubes, the interference effects due to hydrochloric and perchloric acids were eliminated. The matrix modification technique was also investigated for increasing the maximum permissible charring temperature for thallium. The matrix modifiers used included tungsten, zirconium, nickel and tantalum. The effect of adding these modifiers were studied in the presence of different acids. Tungsten increased the maximum permissible charring temperature from 400 to 1000 °C.