Oxidation of the hydrogenated diamond (100) surface

The surface composition and structure of natural diamond (100) surfaces subsequently oxidized with activated oxygen at T_sub≤35°C were investigated with high-resolution electron energy loss spectroscopy (HREELS), Auger electron spectroscopy, electron loss spectroscopy (ELS) and low-energy electron diffraction (LEED). Complete surface oxidation (oxygen coverage θ=1 ML) required doses of hundreds of kilolangmuirs of O₂. HREELS vibrational spectra permitted identification of the specific surface oxygen species, and also provided information about the diamond surface states. Most surface sites lost their hydrogen at least once before becoming oxidized. The oxygen coverage θ increased quickly at first, and then more slowly as saturation was approached; different mechanisms or sites may have accounted for the decreased rate. The relative distribution of oxygen species varied with the oxidation conditions. Ether, carbonyl and hydroxyl groups appeared during the initial stages of oxidation, but the hydroxyl groups disappeared at higher coverages. Bridge-bonded ether groups dominated at saturation coverage, although smaller amounts of carbonyl and hydroxyl were still observed. The carbonyl and C---H stretch frequencies increased with oxygen dose due to formation of higher oxidation states and/or hydrogen bonding between adjacent groups. ELS revealed only a low concentration of C=C dimers on the oxidized surfaces, and no evidence of graphitization.

Surfaces generated by oxygen addition and then desorption were more reactive than surfaces generated by hydrogen desorption. Oxidized surfaces that were heated in vacuum and then rehydrogenated did not recover the sharp LEED patterns and HREELS spectra of the original plasma-smoothed surface. This effect was presumably due to surface roughening caused by oxygen desorption as CO and CO₂, and creation of reactive high-energy sites that quickly bonded to available background gases and prevented large areas of organized surface reconstruction.     

Adsorption of oxygen on Au(111) by exposure to ozone

Atomic oxygen coverages of up to 1.2 ML may be cleanly adsorbed on the Au(111) surface by exposure to O₃ at 300 K. We have studied the adsorbed oxygen layer by AES, XPS, HREELS, LEED, work function measurements and TPD. A plot of the O(519 eV)/Au(239 eV) AES ratio versus coverage is nearly linear, but a small change in slope occurs at Θ_O=0.9 ML. LEED observations show no ordered superlattice for the oxygen overlayer for any coverage studied. One-dimensional ordering of the adlayer occurs at low coverages, and disordering of the substrate occurs at higher coverages. Adsorption of 1.0 ML of oxygen on Au(111) increases the work function by +0.80 eV, indicating electron transfer from the Au substrate into an oxygen adlayer. The O(1s) peak in XPS has a binding energy of 530.1 eV, showing only a small (0.3 eV) shift to a higher binding energy with increasing oxygen coverage. No shift was detected for the Au 4f_7/2 peak due to adsorption. All oxygen is removed by thermal desorption of O₂ to leave a clean Au(111) surface after heating to 600 K. TPD spectra initially show an O₂ desorption peak at 520 K at low Θ_O, and the peak shifts to higher temperatures for increasing oxygen coverages up to Θ_O=0.22 ML. Above this coverage, the peak shifts very slightly to higher temperatures, resulting in a peak at 550 K at Θ_O=1.2 ML. Analysis of the TPD data indicates that the desorption of O₂ from Au(111) can be described by first-order kinetics with an activation energy for O₂ desorption of 30 kcal mol⁻¹ near saturation coverage. We estimate a value for the Au–O bond dissociation energy D(Au–O) to be 56 kcal mol⁻¹.     

Work function changes and surface chemistry of oxygen, hydrogen, and carbon on indium tin oxide

The surface chemistry of indium tin oxide (ITO) has been investigated with Auger electron spectroscopy (AES) and high resolution electron energy loss spectroscopy (HREELS). A vibrating Kelvin probe (KP) with a graphite reference was used to monitor the absolute work function (Φ) of ITO as a function of chemical modification. The ITO was exposed in situ to molecular hydrogen (H₂), hot-filament-activated oxygen (O₂^*), and hot-filament-activated deuterium (D₂^*). The initial Φ of ITO was determined to be 5.2 eV, and surface chemical changes had strong effects on this value, as seen by KP. Exposure of clean ITO to O₂^* increased Φ to 5.6 eV, but the increase was short-lived. The changes in Φ over time were correlated with the uptake of carbon impurities in ultra high vacuum (UHV), as monitored by AES.

The HREELS of ITO revealed significant hydrocarbon impurities. Chemical reduction of ITO produced a metallic surface and dehydrogenated the adsorbed hydrocarbons. Both re-oxidation of metallic ITO and oxidation of clean ITO temporarily removed adventitious carbon from the surface, but oxidized ITO adsorbed an even larger quantity of carbon over time.     

Auger electron spectroscopy and electron energy loss spectroscopy studies on carbonization of Si(100) and (111) surfaces with ethylene

The reactions of Si(100) and Si(111) surfaces at 700 °C (973 K) with ethylene (C₂H₄) at a pressure of 1.3×10⁻⁴ Pa for various periods of time were studied by using Auger electron spectroscopy (AES) and electron energy loss spectroscopy (ELS). For a C₂H₄ exposure level, the amount of C on the (111) surface was larger than that on the (100) surface. The formation of β-SiC grain was deduced by comparing the C_KLL spectra from the sample subjected to various C₂H₄ exposure levels, and from β-SiC crystal.     

Phase transitions in two-dimensional anisotropic chain systems: submonolayers of Sr adsorbed on Mo(112)

Ordered phases of Sr on Mo(112) and their phase transitions have been studied up to one physical monolayer as a function of both coverage and temperature using optical LEED. Starting at a coverage of 0.07, islands of a p(8×1) structure are formed at 100 K, which coexist with a disordered lattice gas. The formation of incommensurate structures with properties of floating solids starts already at coverages slightly above the completed p(8×1) commensurate structure (θ=0.125). The latter itself behaves like a floating solid and undergoes a depinning transition at T≈125 K, similar to the next commensurate structure, p(5×1), which is formed at θ=0.20. Floating solids are found in the whole coverage range between 0.12 and 0.23. At higher coverage coexistence between p(5×1) and c(2×2) structures is found, which melt by forming intermediate two-dimensional eutectics, i.e. coexistence regions with their melts, with an eutectic point at θ=0.37, T_eu=310 K. Close to a coverage of 0.5 a homogenous phase is formed, which disorders by a continuous phase transition, as explicitly tested by determination of the critical exponents β of the order parameter and ν of the correlation length. It is shown that the system belongs to the universality class of the Ising model. An incommensurate phase is again formed at higher coverage due to uniaxial compression of the layers. The behaviour at low coverages can be qualitatively understood assuming lateral interactions along the furrows mainly caused by dipole–dipole interactions and electrostatic screening of the adsorbate induced charge redistribution.     

Elemental steps in the growth of thin β-Ga2O3 films on CoGa(1 0 0)

The oxidation of CoGa(1 0 0) at 700 K was studied by means of high resolution electron energy loss spectroscopy (EELS), scanning tunneling microscopy, low energy electron diffraction and Auger electron spectroscopy (AES). At 700 K, thin well-ordered β-Ga₂O₃ films grow on CoGa(1 0 0). The EEL spectrum of the Ga-oxide films exhibit Fuchs–Kliewer phonons at 305, 455, 645, and 785 cm⁻¹. For low oxygen exposure (<0.2 L), the growth of oxide-islands starts at step edges and on defects. The oxide films have the shape of long, rectangular islands and are oriented in the [1 0 0] and [0 1 0] directions of the substrate. For higher oxygen exposure, islands of β-Ga₂O₃ are found also on the terraces. After an exposure of 200 L O₂ at 700 K, the CoGa(1 0 0) surface is homogeneously covered with a thin film of β-Ga₂O₃.     

Chemical diffusivity of BaTiO3−δ: I. Experimental determination

The chemical diffusivity of ‘undoped' polycrystalline BaTiO_3−δ was determined via a conductivity relaxation technique, at elevated temperatures (800≤T/°C≤1100) as a function of the ambient oxygen partial pressure in the range of 10⁻¹⁶≤P_O2/atm≤1 including an n- to p-type transition regime. Mathematical formulation was developed to convert conductivity relaxation to the corresponding nonstoichiometry (δ) relaxation in the transition regime. It has been found that the chemical diffusivity appears to exhibit a maximum at the n-to-p transition point where the electronic minimum conductivity falls, and that surface reaction becomes more rate-determining than diffusion as the transition point is approached from both n-type and p-type branches. Experimental details are given and the results are exhaustively compared with those reported up to date on the ‘undoped' BaTiO₃.     

Oxygen nonstoichiometry and phase transitions of the neodymium-rich Nd1+xBa2−xCu3Oz solid solution

On the basis of chemical, thermal analysis and Cu K-edge X-ray absorption measurements, oxygen content in the Nd_1+xBa_2−xCu₃O_z solid solution was determined between 1000°C in air and 400°C in oxygen for x=0.05–0.9 compositions. It has been observed that the oxygen nonstoichiometry Δz of the Nd_1+xBa_2−xCu₃O_7+x/2−Δz solid solution decreases 2–2.5 times for a large substitution (Δz≈0.3–0.33 for x=0.9), despite of the acclaimed higher total oxygen content. The difference in nonstoichiometry is explained by a higher average value of the copper oxidation state (ACV), which is vital for the solid solution with large x even at elevated temperatures (ACV≈2–2.05 for x>0.3 at 1000°C, PO₂=0.21 atm). On the contrary, the ACV after complete oxygenation is almost constant (about 2.25–2.3) for the whole series. The x-dependence of the oxygen content is not monotonous and structural phase transitions can be observed at x=0.3 and x=0.6, as confirmed by the X-ray diffraction and the Raman scattering spectroscopy. The first well-known transition is connected with the oxygen disorder due to the Nd substitution for Ba at random Ba-sites. In the present work, it is proved by the apical oxygen mode broadening in Raman spectra. Ordering of the Nd and Ba atoms with a subsequent orthorhombic distortion of the lattice may occur even at 1000°C in air due to the second transformation at x≈0.6. The invariable orthorhombicity of the Nd-rich solid solution with x>0.6 is not caused by the oxygen absorption as in the x=0.05 case. Existence of high- and low-temperature orthorhombic modifications of this solid solution has been observed for the first time. Finally, a tentative 3D (z–x–T) diagram is suggested for the Nd_1+xBa_2−xCu₃O_z solid solution up to 1000°C in air, including the new x=0.6–0.9 region.     

Optimization of synthetic parameters for Tl-2201 superconducting phase by flash sintering process

Samples with nominal composition Tl₂Ba₂Cu_1.2 (copper-rich Tl-2201) were calcined at various temperature, i.e. from 865 °C to 910°C and for various durations (10–20 h). The samples were sintered for 31/2 min at various temperatures. The X-ray powder diffraction pattern indicates that most of the Tl-Ba-Cu samples (Tl-2201) are single-phase materials. All the lines in the X-ray pattern are indexable on a tetragonal unit cell showing tetragonal symmetry having space group 14/mmm with a=3.86 Å C=23.11 ± 0.06 Å as unit cell parameters. R−T and AC susceptibility measurements show T^on_c, from 90 to 104 K. There is an elongation of the c-axis (c=23.24 Å) for the sample showing the highest T_c. Wet chemical analysis confirms the deficiency of thallium. This suggests some substitution of Cu in place of thallium which leads to an increase in the average oxidation state of copper, responsible for the creation of holes (charge carriers).     

Aspects of “low field” magnetotransport in epitaxial thin films of the ferromagnetic metallic oxide SrRuO3

Epitaxial thin films of the conductive ferromagnetic oxide SrRuO₃ were grown on an (0 0 1) SrTiO₃ (STO) substrate by using DC sputtering technique. The magnetic and magnetoresistive properties of the films were measured by applying the magnetic field both perpendicular (out-of-plane) and parallel (in-plane) to the film plane and ever maintaining the direction of the applied field perpendicular to that of the transport current. The films grown on an (0 0 1) STO substrate showed identical magnetization properties in two orthogonal crystallographic directions of the substrate, [1 0 0]_S and [0 0 1]_S (in-plane and out-of-plane geometry), which suggests the presence of a multi domain structure within the plane of the film. For such samples, no anisotropic field (hard axis) along de [0 0 1]s direction, i.e., perpendicular to the film-plane could be detected. Nevertheless, a distinguishable temperature dependent out-of-plane anisotropic magnetoresistance (MR) along with strong temperature dependent low field hysteretic MR(H) behavior was detected for the studied films. A negative MR ratio MR(T)=[ρ(μ₀H=9 T; T)−ρ( μ₀H=0 T; T)]/ρ( μ₀H=0 T; T) on the order of a few percent, with maximums of 6% and 4% (right at the Curie temperature, T_C 160 K) was calculated for an in-plane and out-of plane measuring geometry, respectively. In addition there is an equally strong MR effect at low temperatures, which might be related to the temperature dependence of the magnetocrystalline anisotropy together with a magnetization rotation. Both the MR(T) behavior and the achieved values (except for T<30 K) are similar to those obtained on SrRuO₃ films grown on 2° miscut (0 0 1) STO substrates with the current parallel to the field and parallel to the direction, which was identified as the easier axis for magnetization.     

Peak effect and oxygen ordering in YBa2Cu3O7−δ single crystals

We have investigated the second magnetization peak in pure YBa₂Cu₃O_7−δ single crystals with various oxygen contents (6.91<7−δ<6.97) and degrees of oxygen vacancy ordering, as achieved by low (1 bar) and high (100 bar) oxygen pressure annealing. Although the position of the peak changes drastically with oxygen stoichiometry, no dependence on the distribution of oxygen vacancies has been found for temperatures below 70 K. For T>70 K, however, ordering effects become important as demonstrated by the disappearance of the peak for the high pressure annealed samples. These results suggest that while at low temperatures, pinning of the vortex system by clusters or a more homogeneous distribution of oxygen vacancies is similar, at elevated T, the former are much stronger pinning sites leading to larger hysteresis and the presence of the peak.     

Structural properties of diamond fine particles and clusters prepared by detonation and decomposition of TNT

The thermal parameter B for three different particle sizes of diamond samples (bulk powder 1–4 μm, fine particle 144–195 Å and cluster 55–61 Å) was determined by the grazing incidence X-ray diffraction method. The values of B were found to be in the range 0.50–0.70 Å² for particles in the size range 195–55 Å and 0.27 Å² for 1–4 μm. All of them are larger than that of diamond bulk. A clear size dependence of B, increasing with decreasing particle size, was found. By analysing X-ray diffraction data at several temperatures the magnitude of B was found to be due to B_S (static part) instead of B_T (dynamic part). The average B_S values obtained were 0.04 Å², 0.19 Å² and 0.27 Å² for bulk powder, fine particle and cluster samples respectively. Ultrahigh resolution transmission electron microscope (TEM) observation confirmed the presence of strain, distortion, roughness and dislocation lines in many particles. TEM images of particles indicate that the clusters were not spherical in shape; they were mostly cubiform and some were truncated prism-like polyhedral. The present study reveals that the B_S component is responsible for the large B value in diamond fine particles and clusters. No clear surface local atomic distortion was found in the particles.     

Investigation of the static and dynamic magnetic properties of CoFe2O4 nanoparticles

We have investigated the magnetic behavior of cobalt ferrite nanoparticles with a mean diameter of 7.2 nm. AC susceptibility of colloidal cobalt ferrite nanoparticles was measured as a function of temperature T from 2 to 300 K under zero external DC field for frequencies ranging from f=10 to 10,000 Hz. A prominent peak appears in both χ′ and χ″ as a function of T. The peak temperature T₂ of χ″ depends on f following the Vogel–Fulcher law. The particles show superparamagnetic behavior at room temperature, with transition to a blocked state at T_B^m94 K in ZFC and 119 K in AC susceptibility measurements, respectively, which depends on the applied field. The saturation magnetization and the coercivity measured at 4.2 K are 27.3 emu/g and 14.7 kOe, respectively. The particle size distribution was determined by fitting a magnetization curve obtained at 295 K assuming a log-normal size distribution. The interparticle interactions are found to influence the energy barriers yielding an enhancement of the estimated magnetic anisotropy, K=6×10⁶ erg/cm³. Mössbauer spectra obtained at higher temperatures show a gradual collapse of the magnetic hyperfine splitting typical for superparamagnetic relaxation. At 4.2 K, the Mössbauer spectrum was fitted with two magnetic subspectra with internal fields H_int of 490, 470 and 515 kOe, corresponding to Fe³⁺ ions in A and B sites.     

X-ray and high resolution selenium-77 solid state NMR spectroscopy as complementary probes to structural studies of organophosphorus diselenides

high resolution solid state NMR spectroscopy was employed to study structural properties of bis(diisopropoxyphosphorothioyl) diselenide 1 and bis(dineopentoxyphosphorothioyl) diselenide 2. The principal elements T_ii of effective dipolar/chemical shift tensor were calculated from spinning sideband intensities employing the WIN-MAS program. The values of anisotropy and asymmetry parameters reflect the distortion of the selenium environment. It was found that the T₃₃ component mostly contributes to changes in the isotropic chemical shifts. CP/MAS experiments were used to decide the assignment of space group by counting the number of crystallographically unique selenium centers in the unit cell. Crystals of diselenide 1 are triclinic, space group P with a=8.485(3) Å, b=8.508(1) Å, c=8.511(2) Å, =98.835(15)°, β=111.653(24)°, γ=93.524(21)°, V=559.5(3) ų, D_c=1.544(2) g/cm³ and Z=1. Refinement using 2222 reflections for 157 variables gives R=0.037. Crystals of diselenide 2 are triclinic, space group P1 with a=9.1418(8) Å, b=9.1465(8) Å, c=9.9200(9) Å, =74.751(8)°, β=74.629(7)°, γ=82.216(7)°, V=769.7(1) ų, D_c=1.365(2) g/cm³ and Z=1. Refinement using 3316 reflections for 297 variables gives R=0.0272.     

Hydrogen adsorption on Mo1−xRex(110) (x=0–0.25) surfaces

The effects of adsorbed H on the Mo_1−xRe_x(110), x=0, 0.05, 0.15, and 0.25, surfaces have been investigated using low-energy electron diffraction (LEED) and high-resolution electron energy loss spectroscopy (HREELS). For the x=0.15 alloy only, a c(2×2) LEED pattern is observed at a coverage Θ0.25 ML. A (2×2) pattern is observed for H coverages around Θ0.5 ML from surfaces with x=0, 0.05, and 0.15. Both c(2×2) and (2×2) patterns are attributed to reconstruction of the substrate. At higher coverages, a (1×1) pattern is observed. For the alloy surface with x=0.25, only a (1×1) pattern is obtained for all H coverages. Two H vibrations are observed in HREELS spectra for all Re concentrations, which shift to higher energies at intermediate coverages. Both peaks exhibit an isotopic shift, confirming their assignment to hydrogen. For Re concentrations of x=0.15 and higher, a third HREELS peak appears at 50 meV as H (D) coverage approaches saturation. This peak does not shift in energy with isotopic substitution, yet cannot be explained by contamination. The intrinsic width of the loss peaks depends on the Re concentration in the surface region and becomes broader with increasing x. This broadening can be attributed to surface inhomogeneity, but may also reflect increased delocalization of the adsorbed hydrogen atom.     

Proton conductivity of phosphoric acid derivative of fullerene

The proton conductive property of methano [60] fullerene diphosphoric acid has been investigated under various humidity conditions at the temperature range between 15 and 45 °C. It shows proton conductivity as high as 10⁻² S cm⁻¹ at 25 °C under relative humidity of 95%. Thermal analyses including TG–DTA and thermal desorption mass spectroscopy (TDS) confirm that the compound is thermally stable up to 200 °C. Proton conduction of the compound depends very much on humidity or water content. The logarithmic conductivity at 25 °C is increased linearly with increasing relative humidity. The activation energy (E_a) estimated from the slope of log(σT) vs. 1/T is decreased from 1.08 to 0.52 eV, as the relative humidity is increased from 40% to 75%. The humidity dependence of conductivity is discussed in the light of the observed hydration isotherm.     

Magnetic phase transition in (Fe,Mn)65Ni35 alloys

Magnetization measurements on the Fe₆₀Mn₅Ni₃₅ and Fe₅₀Mn₁₅Ni₃₅ alloy samples were carried out in the temperature range 80T300 K and in magnetic fields up to 8 kOe. The Fe₆₀Mn₅Ni₃₅ was found to order ferromagnetically with a Curie temperature, T_c, above 300 K. From the temperature dependence of the spontaneous magnetization, M_s, it was concluded that the magnetic behavior of Fe₆₀Mn₅Ni₃₅ follows Wohlfarth theory of weak itinerant ferromagnet. The Fe₅₀Mn₁₅Ni₃₅ sample exhibits a magnetic phase transition from ferromagnetism to paramagnetism at T_c=242 K. The critical amplitudes and critical exponents (β, γ and δ) have been determined by using Arrott plots, Kouvel–Fisher method and scaling plots of the reduced magnetization and reduced magnetic field. The values of β, γ and δ are discussed and compared with the results obtained for various theoretical models and also with the experimentally determined values for related systems obtained by others.     

Conductivity anisotropy in directionally solidified CaZrO3---CaSZ and MgO-MgSZ eutectics

The results of the impedance spectroscopy measurements on eutectic samples based on zirconium oxide are presented here. Samples of CaZrO₃---ZrO₂(cubic) and MgO---ZrO₂(cubic) have been grown by a directional solidification procedure such that the different phases appear nearly oriented along the growth direction (lamellae in the system of CaZrO₃-ZrO₂(cubic) and fibers of MgO in a ZrO₂ matrix in the other system). The DC electrical conductivity has been measured by impedance spectroscopy along and across the growth axis. For CaZrO₃---ZrO₂ the coductivity is clearly anisotropic. The following values for σT have been obtained: the conductivity at 600 °C equals 2.0 × 10⁻⁶ Ω⁻¹ cm⁻¹ perpendicular to the fiber axis and 1.4 × 10⁻⁵ Ω⁻¹ cm⁻¹ parallel to it and with an activation energy of 1.3 eV for σT. For MgO---ZrO₂(cubic) the isotropic value of the conductivity at 600 °C is 10⁻⁴ Ω⁻¹ cm⁻¹ with activation energy for σT of 1.5 eV. The anisotropic conductivity in the CaZrO₃---ZrO₂ (cubic) system has been explained by a model of an ordered stacking of oxygen conducting (cubic ZrO₂) and non-conducting (CaZrO₃ or MgO) phases.     

The adsorption of CO on Ir(111) investigated with FT-IRAS

The adsorption of CO on Ir(111) has been investigated with Fourier transform infrared reflection-absorption spectroscopy, temperature programmed desorption, and low-energy electron diffraction. At sample temperatures between 90 and 350 K, only a single absorption band, above 2000 cm⁻¹, has been observed at all CO coverages. For fractional coverages above approximately 0.2, the bandwidth becomes as narrow as 5.5 cm⁻¹. The linewidth is attributed mainly to inhomogeneous broadening at low CO coverages and to the creation of electron-hole pairs at higher CO coverages. The coverage-dependent frequency shift of the IR band can be described quantitatively using an improved dipolar coupling model. The contribution of the dipole shift and the chemical shift to the total frequency shift were separated using isotopic mixtures of CO. The chemical shift is positive with a constant value of approximately 12 cm⁻¹ for all coverages, whereas the dipole shift increases with coverage up to a value of 36 cm⁻¹ at a coverage of 0.5 ML.     

Superconductivity, Ca content and oxygen deficiency of Ga(Sr,Ca)2(Yb,Ca)Cu2O7

Superconducting transition temperature (T_c), Ca content and oxygen deficiency are studied on GaSr_1.8Ca_0.2Yb_1−xCa_xCu₂O₇ (x≤0.35). Superconducting samples with T_c=52 K are prepared after the annealing at 20 MPa of oxygen. The T_c is reduced through a slight oxygen loss accompanied by annealing in air above 650°C. The oxygen loss suggests the presence of short Cu–O chains in the GaO₄ slab. The formal valence of planar Cu required for the appearance of superconductivity depends on oxygen and Ca contents. The critical formal Cu valences are 2.105 and 2.125 for the samples annealed in air at 600°C and at 835°C, respectively. The values are higher than those of usual high-T_c superconductors. This can be explained by a high concentration of localized holes in the CuO₅ slab.