Control of dispersion state of silsesquioxane nanofillers for stabilization of polystyrene thin films

The influence of the dispersion states of the nanofillers on the dewetting behavior of the polymer thin film was investigated. Polyhedral oligomeric silsesquioxanes (POSS) with various substituents were added into polystyrene (PS) thin films as the nanofillers. The dewetting rate of the films drastically changed with the surface substituents of POSS additives. Neutron reflectivity measurements indicated that the difference of the dewetting rate was associated with the dispersion state of POSS additives in the films. POSS with phenethyl groups (PhPOSS), which homogeneously dispersed into the films, resulted in the decrease of the glass transition temperature of PS and the enhancement of the dewetting of the films. POSS with a fluoroalkyl group (CpPOSS-R f) segregated to the film surface and showed the retardation of the dewetting by the decrease of the surface energy of the film. POSS with hydroxyl groups (CpPOSS-2OH) segregated to the film surface and film-substrate interface and led to the elimination of the dewetting, suggesting the importance of the interfacial segregation for the inhibition of dewetting. These results revealed the strong relationship between the dispersion state of the nanofillers and the dewetting of the nanofilled films.     

Effect of dopant on the physical properties of polymer films for microphotonics

This paper presents experimental results concerning the influence of the additives on the physical properties of polymer films. Metal oxides/inorganic salts were used as additives in vinyl-polymers solutions. The physical properties of the metal doped polymer films can be significantly modified by the composition of the doping elements and the curing conditions of the polymer. Morphologic, electronic, magnetic and optic properties of the doped polymers were analysed by AFM, SEM, Mössbauer spectroscopy and optical measurements. The film composition and the deposition processes were optimized to allow a better control of the optical parameters (refractive index, transmission), to reduce the processing temperatures and to improve the chemical sensitivity of the films for sensor applications. These compounds can be easily spin coated onto a variety of directly patterned semiconductor substrates.     

Surface-assisted photoalignment of discotic liquid crystals by nonpolarized light irradiation of photo-cross-linkable polymer thin films

In this article, we describe the surface-assisted photoalignment of discotic liquid crystals (DLCs) on thin films of photo-cross-linkable polymers with cinnamoyl moieties as the side chains. Oblique irradiation of the polymer thin films with nonpolarized UV light at 313 nm brought about inclined orientation of the cinnamoyl residues as a result of their direction-selective photoisomerization and photodimerization. The DLC molecules on the photoirradiated polymer films were aligned in a tilted hybrid manner. This means that the DLC directors are continuously altered from the substrate to the DLC film surface so as to minimize the elastic free energy. Interestingly, we found that the tilted direction of aligned DLC molecules is clearly influenced by the chemical structures of the cinnamate-containing polymers. When a poly(vinyl cinnamate) thin film was obliquely exposed to nonpolarized UV light, the DLCs were inclined to the direction opposite to the UV light propagation. In a keen contrast, the thin film of poly(methacrylate)s tethering cinnamoyl groups, which was obliquely exposed to nonpolarized UV light in advance, provided the tilting DLC direction in parallel with the light propagation. The results were supported by tilted orientation of calamitic (rod-shaped) liquid crystal on the obliquely irradiated polymer films. Such photoalignment behavior of the DLCs can be rationalized by anchoring balance between intermolecular interaction of the DLC molecules with the photodimers of polymer films and those with the remaining E-isomers of cinnamoyl side chains at the film interface. The present technique of DLC photoalignment opens promising ways not only to understand anisotropic physical properties of DLCs, but also to design and fabricate novel nanodevices for photonics and electronics applications.     

Properties of Langmuir Surface and Interfacial Films Built up by Asphaltenes and Resins: Influence of Chemical Demulsifiers

The influence of chemical additives on asphaltene films on water surface and at oil/water interface is studied by means of the Langmuir technique. It was found that some demulsifiers of high molecular weight alter the asphaltene film on water surface in the same way as the resin fraction, i.e., increasing the compressibility of the film which results in a reduced film rigidity. The films that build up at the oil/water interface in model oil systems, containing naturally occurring surfactants, are studied during compression. In this system chemical additives of high molecular weight totally prevent formation of a rigid film at the interface. Adding resins to the bulk phase together with asphaltenes hamper the adsorption of the heavy fraction.     

Soluble organic additive effects on stress development during drying of calcium carbonate suspensions

The effect of polymer, plasticizer, and surfactant additives on stress development during drying of calcium carbonate particulate coatings was studied using a controlled-environment apparatus that simultaneously monitors drying stress, weight loss, and relative humidity. We found that the calcium carbonate coatings display a drying stress evolution typical of granular films, which is characterized by a sharp capillary-induced stress rise followed by a rapid stress relaxation. The addition of a soluble polymer to the CaCO3 suspension resulted in a two-stage stress evolution process. The initial stress rise stems from capillary-pressure-induced stresses within the film, while the second, larger stress rise occurs due to solidification and shrinkage of the polymeric species. Measurements on the corresponding pure polymer solutions established a clear correlation between the magnitude of residual stress in both the polymer and CaCO3-polymer films to the physical properties of the polymer phase, i.e. its glass transition temperature, T(g), and Young's modulus. The addition of small organic molecules can reduce the residual stress observed in the CaCO3-polymer films; e.g., glycerol, which acts as a plasticizer, reduces the drying stress by lowering T(g), while surfactant additions reduce the surface tension of the liquid phase, and, hence, the magnitude of the capillary pressure within the film.     

Synthesis and structure features of composite silicate and hybrid TEOS-derived thin films doped by inorganic and organic additives

The results of long-term researches of thin films prepared from tetraethoxysilane-derived sols containing inorganic and organic additives are systematized and analyzed. These additives give to films certain physicochemical properties for their application in electronic techniques, optics, power engineering, in biological technologies etc. The influence both inorganic (salts, acids) and organic (polyols, polyionenes, epoxy resin) additives on rheological properties and aggregate stability of sols as well as films surface morphology is minutely considered. The explanations of phenomena during film formation, including spin-coating process, are given. Essential influence of temperature and humidity on films surface morphology is shown. Influence of heat treatment modes on structure and composition of films is analyzed. Recommendations about optimization of thin films sol–gel processing are offered.     

Roughness correlation and interdiffusion in thin films of polymer chains

The surface morphology of thin bilayer polymer films on top of glass substrates was investigated. The bilayer consists of a blend film of protonated and deuterated polystyrene and an underlying deuterated polystyrene film. Choosing the thickness of the top film larger than 8 times and smaller than 2 times the radius of gyration of the chains enables the determination of film thickness and confinement effects. With diffuse neutron scattering at grazing incidence in the region of total external reflection, a depth sensitivity and a contrast even at the internal polymer–polymer interface was achieved. The underlying film is conformal to the substrate, and depending on the thickness of the top film two different types of roughness correlations are observed. Thin confined films nestle to the underlying polymer films, while the stiffness of thicker bulky films provides an independent morphology. In both cases, annealing above the glass-transition temperature yields an interdiffusion at the internal polymer–polymer interface, and the polymer–air surface remains essentially unchanged with respect to roughness correlations. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2862–2874, 1999     

Growth of highly oriented crystalline polyaniline films by self-organization

Silicon substrates with (100) orientation were modified with amino-silane self-assembled monolayer (SAM) to provide amino (NH(2)) moieties at the substrate surface. Self-organization of polyaniline during chemical polymerization, on this modified surface, leads to the growth of highly oriented films at the substrate-polymer interface. The morphology studied using scanning electron microscopy and atomic force microscopy revealed the formation of polymer film with well faceted pyramidal crystallites. XPS and FTIR spectroscopy were used to analyze the chemical structure of the film. X-ray diffraction measurements show the crystalline nature of the polyaniline, whose lattice parameters are in agreement with the reported values. This study underlines the importance of a SAM in deciding the structure and morphology of the deposited polymer.     

Mixed films of poly(n-hexyl isocyanate) and poly(vinyl acetate) at the air-water interface

We study interfacial properties of rigid-rod-like poly(n-hexyl isocyanate) (PHIC), flexible poly(vinyl acetate) (PVAc), and mixed films of PHIC and PVAc spread at the air-water interface as a function of the molar fraction of PHIC by surface pressure measurements and fluorescence microscopy. From the plots of the experimental mean area of the mixed polymer films at a constant surface pressure as a function of the molar fraction of PHIC in the mixed films, the binary mixtures of PHIC/PVAc were concluded to be compatible at the air-water interface. This means that the hydrophobic hexyl group of PHIC takes a horizontal orientation to the air-water interface rather than a perpendicular one, leading to PHIC and PVAc having the same interfacial orientation. Compatibility of the binary mixtures of PHIC/PVAc at the air-water interface is also confirmed by their fluorescence microscopic images, since PHIC proves to be inhomogeneous and PVAc is homogeneous with the aid of a fluorescence probe, respectively.     

Nanotribology of surface-grafted PEG layers in an aqueous environment

The lubrication properties of adsorbed poly(L-lysine)-graft-poly(ethylene glycol) in aqueous buffer solution were studied with the surface forces apparatus. In general, the polymer brushes revealed extremely low friction forces. Two distinct regimes could be identified. In response to lateral shear, the friction forces of intact polymer films at moderate loads were below the detection limit. At high loads, when the films were compressed to about 10% of the original equilibrium film thickness, the friction showed a reversible increase with load. Under certain conditions, film destruction was observed, immediately followed by a dramatic increase in the frictional force and an expansion of the adsorbed brush layer. By the addition of free polymer to the buffer solution, the resistance of the polymer brushes to abrasion was dramatically increased by readsorption of the polymer following friction-induced desorption. This self-healing capacity and the extremely low friction of the adsorbed copolymer films contribute to their excellent properties as lubricant additives for water-based lubrication under boundary conditions.     

Surface modification of polyethylene with multi-end-functional polyethylene additives

We have prepared and characterized a series of multifluorocarbon end-functional polyethylene additives, which when blended with polyethylene matrices increase surface hydrophobicity and lipophobicity. Water contact angles of >112° were observed on spin-cast blended film surfaces containing less than 1% fluorocarbon in the bulk, compared to ~98° in the absence of any additive. Crystallinity in these films gives rise to surface roughness that is an order of magnitude greater than is typical for amorphous spin-cast films but is too little to give rise to superhydrophobicity. X-ray photoelectron spectroscopy (XPS) confirms the enrichment of the multifluorocarbon additives at the air surface by up to 80 times the bulk concentration. Ion beam analysis was used to quantify the surface excess of the additives as a function of composition, functionality, and molecular weight of either blend component. In some cases, an excess of the additives was also found at the substrate interface, indicating phase separation into self-stratified layers. The combination of neutron reflectometry and ion beam analysis allowed the surface excess to be quantified above and below the melting point of the blended films. In these films, where the melting temperatures of the additive and matrix components are relatively similar (within 15 °C), the surface excess is almost independent of whether the blended film is semicrystalline or molten, suggesting that the additive undergoes cocrystallization with the matrix when the blended films are allowed to cool below the melting point.     

Scanning force microscopy of polyester: surface structure and adhesive properties

Scanning force microscopy has been used to characterize the surface structure and properties of poly(ethylene terephthalate) (PET) films. Two types of biaxially oriented film have been studied: one (Melinex O) is free of additives while the other (Mylar D) contains particulate additives at the surface. Contact mode characterization of both materials provide clear images of the polymer surface and (in the case of Mylar D) the additives. Phase images reveal substantial nanoscale morphological detail, including small features thought to be crystallites. To model the adhesive properties of polymer surfaces, mixed self‐assembled monolayers containing polar and methyl terminated adsorbates were studied using chemical force microscopy. It was found that the strength of the tip‐sample adhesion increased with the fraction of polar terminated adsorbates at the surface when a carboxylic acid terminated tip was employed, while the trend was reversed when a methyl terminated tip was used. Adhesion forces measured for plasma treated PET increased with treatment time, and linearly with the cosine of the water contact angle, illustrating the chemical selectivity of chemical force microscopy. However, friction forces were found to vary in a non‐linear fashion, indicating that changes to the polymer surface mechanical properties following treatment were important.     

Comparative behavior of electrodes coated with thin films of structurally related electroactive polymers

General methods are described for the synthesis of electroactive polymers and the preparation of uniform, stable, polymer-coated electrodes. The electrochemical behaviour of thin films of eight different functionalized polystyrenes, differing in the identity and amount of attached electroactive species, and polyvinylferrocene is presented. A wide range of electrochemical properties can be observed by varying parameters such as film thickness, nature of the bound redox couple, extent of polymer functionalization and oxidation state. The deviations from ideal surface behavior are investigated in detail. These are shown to be consequences of cooperative electronic interactions, structural reorganization or uncompensated resistance within the film, depending upon the material. The film resistance varies greatly among the polymer films studied and is shown, in some cases, to be a sensitive function of the extent of oxidation and prior treatment of the film. This variable resistance is shown to be a consequence of slow ion transport through the film. The mechanism of electron transport in such materials is considered and a model of the metal/polymer/electrolyte interface is proposed.     

Ordering of PCDTBT Revealed by Time‐Resolved Electron Paramagnetic Resonance Spectroscopy of Its Triplet Excitons

Time‐resolved electron paramagnetic resonance (TREPR) spectroscopy is shown to be a powerful tool to characterize triplet excitons of conjugated polymers. The resulting spectra are highly sensitive to the orientation of the molecule. In thin films cast on PET film, the molecules’ orientation with respect to the surface plane can be determined, providing access to sample morphology on a microscopic scale. Surprisingly, the conjugated polymer investigated here, a promising material for organic photovoltaics, exhibits ordering even in bulk samples. Orientation effects may significantly influence the efficiency of solar cells, thus rendering proper control of sample morphology highly important.     

Anchoring properties of a nematic liquid crystal on anisotropic hydroxypropylcellulose films

Thin solid films of hydroxypropylcellulose (∼15-30 µm) prepared from liquid crystalline and isotropic aqueous solutions are used as liquid crystal alignment layers. Using the standard nematic liquid crystal 5CB we measured the interface properties of these solid films as a function of the polymer concentration in the aqueous precursor solution, expressed in terms of zenithal and azimuthal anchoring orientations and extrapolation lengths. The hydroxypropylcellulose thin films are found to induce a planar orientation of 5CB independently of the polymer concentration, with the alignment along the polymer backbone. The zenithal anchoring strength is found to be strong and essentially independent of the temperature far from the nematic-isotropic transition, with an extrapolation length ξ_θ≈50 nm. The zenithal anchoring becomes weaker near the nematic-isotropic transition, as expected. The azimuthal anchoring strength is found to be intermediately weak and strongly dependent on the polymer concentration, with an extrapolation length varying from ξ_θ≈250 nm to ξ_ϕ≈500 nm. These films are particularly interesting since their surface topography and morphology may be tuned by varying a few parameters in the film preparation process, such as the polymer concentration in the aqueous solution.     

PM-IRRAS spectroscopy for the characterization of polymer nanofilms: chains conformation,anisotropy and crystallinity

This paper is focused on the use of the Polarization-Modulation Infrared Reflection-Absorption Spectroscopy (PM-IRRAS) for studying thin polymer films at interfaces. When forming a polymer film on a metallic substrate, for instance by spin-coating, the characterization of the polymeric layer becomes very difficult given the small amount of matter deposited and also because of the contact with the metal. Among the techniques well adapted to surface and interface analyses, the PM-IRRAS spectroscopy represents an excellent tool to probe ultra-thin films. Different systems have been selected in this study such as polyamides (PA) and ethylene-co-vinyl acetate (EVA) nanofilms spin-coated onto chemically controlled surfaces (i.e. thiol self-assembled monloayers grafted onto gold coated glass slides). PM-IRRAS spectroscopy allowed us to characterize the polymer anisotropy (chains orientation and conformation), to suggest a model for chain organization at the polymer/substrate interface, and to calculate the orientation angles. Moreover, we were able to determine, by using PM-IRRAS, the degree of crystallinity of PA and EVA films of nanometric dimensions without any calibration procedure needed by other techniques.     

Flammability Tests and Investigations of Properties of Lignin-Containing Polymer Composites Based on Acrylates

In this paper flammability tests and detailed investigations of lignin-containing polymer composites’ properties are presented. Composites were obtained using bisphenol A glycerolate (1 glycerol/phenol) diacrylate (BPA.GDA), ethylene glycol dimethacrylate (EGDMA), and kraft lignin (lignin alkali, L) during UV curing. In order to evaluate the influence of lignin modification and the addition of flame retardant compounds on the thermal resistance of the obtained biocomposites, flammability tests have been conducted. After the modification with phosphoric acid (V) lignin, as well as diethyl vinylphosphonate, were used as flame retardant additives. The changes in the chemical structures (ATR-FTIR), as well as the influence of the different additives on the hardness, thermal (TG) and mechanical properties were discussed in detail. The samples after the flammability test were also studied to assess their thermal destruction.     

Incorporation of sparingly soluble species in mesostructured surfactant-polymer films

Recently we have investigated the formation of novel thick, solid, mesostructured films of polymer/surfactant mixtures which form spontaneously at the air-solution interface. Here we report studies of the effect of adding a series of sparingly soluble species to the precursor solution, to alter the mesostructure of cetyltrimethylammonium bromide/polyethylenimine films and to investigate the incorporation of small molecules within the films. Small-angle neutron scattering confirmed that cyclohexane and decane evenly swell the micelles in film forming solutions, while cyclohexanol extends the prolate micelles along their long axis. Although the presence of these additives in solution did not greatly affect the formation of the film, it was observed that they did influence the structure of the films. Films produced with decane consisted of a cubic phase rather the conventional 2-D hexagonal phase, whilst both cyclohexane and cyclohexanol enhance the level of ordering in low MW polymer films. Benzene was found to have no significant effect on the film.     

Two-dimensional surface properties of PEO-PPO-PEO triblock copolymer film at the air/water interface in the absence and presence of Tyr-Phe dipeptide, Val-Tyr-Val tripeptide, SDS and stearic acid

Two-dimensional surface properties of PEO-PPO-PEO triblock copolymer film (Mol.Wt. 2800) in the absence and presence of Tyr-Phe dipeptide, Val-Tyr-Val tripeptide, sodium dodecylsulfate and stearic acid have been investigated for the first time at the air/water interface using Langmuir film balance technique. It is observed that the above polymer forms fairly stable film at the air/water interface. There are no significant changes observed in the surface pressure-area (π-A) isotherms of polymer in the presence of SDS. However, more expanded film was formed in presence of SDS since the solubility of the polymer is more in SDS and the polymer network is disturbed in presence of SDS, which results in the increase in surface area of the polymer films. In the presence of dipeptide and tripeptide, the surface area of the polymer film decreased with a slight increase in the surface pressure indicating the binding of these peptides to polymer, which enhances the stability of the polymer film. Thermodynamic studies on the change in surface area (ΔA) and excess free energy of mixing (ΔG(mix)(E)) associated with the formation of the mixed film suggest the occurrence of a thermodynamically unstable mixed film. The presence of SDS slightly decreases the formation of mixed film of stearic acid with triblock copolymer and peptides due to the solubilization of these compounds in SDS. However, the hydrophobicity of the polymer films increases in the presence of stearic acid, leading to the increase in surface pressure. The positive deviation of ΔA and the positive ΔG(mix)(E) values show the non-ideality and incompatibility of thermodynamically unstable mixed films. The thermodynamic results suggest that the stability and compatibility of the polymer, peptides and their mixed films with stearic acid in the presence of SDS are decreased, which is in good agreement with the results obtained for other polymeric systems.     

利用呼吸图案法制备聚(苯乙烯-b-丙烯腈)有序多孔薄膜

以自制的聚(苯乙烯-b-丙烯腈)(PS-b-PAN)嵌段共聚物为成膜材料, 采用呼吸图案法制备了有序多孔薄膜, 采用扫描电子显微镜(SEM)对薄膜形貌进行了分析, 研究了聚合物浓度、溶剂种类及共聚物结构对薄膜结构的影响. 结果表明, 薄膜表层为多孔结构, 且孔为圆形、以六方阵列形式排列; 薄膜表层下面是蜂窝状结构.以三氯甲烷(CHCl₃)为溶剂时, 在较高浓度下制备的薄膜表层孔间距较大, 蜂窝结构尺寸较小, 且形成了多层结构. 与CHCl₃为溶剂时相比, 挥发速度较快的二硫化碳(CS₂)作溶剂时制备的多孔薄膜有序性较好, 薄膜表层孔径和孔间距均较大, 蜂窝结构尺寸较小. 以没有PAN链段的聚苯乙烯大分子引发剂(PS-Cl)为成膜材料时, 制备的薄膜表层没有形成多孔结构, 而是形成了窝状结构. 同时, 通过对薄膜表层晕的研究证明了多孔薄膜表层缺陷是由水滴处于液膜下较深的位置造成的.