Determination of zinc and copper in human hair by slurry sampling employing sequential multi-element flame atomic absorption spectrometry

The present work proposes a direct method based on slurry sampling for the determination of zinc and copper in human hair samples by multi-element sequential flame atomic absorption spectrometry. The slurries were prepared by cryogenic grinding and sonication of the samples. The optimization step was performed using univariate methodology and the factors studied were: nature and concentration of the acid solution, amount sample/slurry volume, sonication time, and particle size. The established experimental conditions are the use of a sample mass of 50 mg, 2 mol L^− 1 nitric acid solution, sonication time of 20 min and slurry volume of 10 mL. Adopting the optimized conditions, this method allows the determination of zinc and copper with detection limits of 88.3 and 53.3 ng g^− 1, respectively, and precision expressed as relative standard deviation (RSD) of 1.7% and 1.6% (both, n = 10) for contents of zinc and copper of 100.0 and 33.3 μg g^− 1, respectively. The accuracy was checked and confirmed by analysis of two certified reference materials of human hair. The procedure was applied for the determination of zinc and copper in two human hair samples. The zinc and copper contents varied from 100.0 to 175.6 and from 3.2 to 32.8 μg g^− 1, respectively. These samples were also analyzed after complete digestion in a closed system and determination by FAAS. The statistical comparison by t-test (95% confidence level) showed no significant difference between these results.     

Assessment of a dynamic hollow-fibre liquid phase microextraction system for human blood plasma samples

A dynamic liquid phase microextraction (LPME) system, based on hollow-fibre supported liquid membrane (SLM) extraction, was developed for extracting ionisable xenobiotics from human plasma, and its performance was evaluated (in terms of extraction efficiency, reproducibility, durability and carry-over) using nitrophenolic compounds as model analytes at concentrations of 0.1–0.5 μg mL^?1 in aqueous standards. The efficiency and repeatability were tested also on spiked human plasma. The system is non-expensive, convenient, requires minimal manual handling and enables samples with volumes as small as 0.2 mL to be extracted. For plasma samples extraction efficiencies of between 30 and 58% were achieved within 20 min, including washing steps. The limit of detection (LOD) values were in the range 0.02–0.03 μg mL^?1. The developed system can provide enrichment factors up to eight, based on the injection-to-acceptor volume ratio (in this case 0.2–0.025 mL). The same hollow-fibre membrane was used up to 8 days with no loss of efficiency. Carry-over was lower than detection limit.     

SPME and SPE comparative study for coupling with microwave-assisted micellar extraction in the analysis of organochlorine pesticides residues in seaweed samples

Solid-phase microextraction (SPME) and solid-phase extraction (SPE) procedures were coupling with microwave-assisted micellar extraction for organochlorine pesticides residues determination in seaweed samples. They were optimized, compared and discussed.Preliminary experiments were performed in order to study experimental conditions for the extraction of pesticides from spiked seaweed samples with microwave-assisted micellar extraction (MAME) using a non-ionic surfactant (Polyoxyethylene 10 Lauryl Ether). After that, SPME and SPE were used to clean-up and preconcentrate MAME extract prior the analysis by liquid chromatography with photodiode array (PDA) detection.Excellent results were obtained for both procedures. Average pesticide recoveries between 80.5 and 104.3% for MAME-SPME and between 73.9 and 111.5% for MAME-SPE were obtained. Relative standard deviations (RSDs) were lower than 10.3% and 5.3% respectively for all recoveries tested, and LOD between 138–348 ng g^− 1 for MAME-SPME and 2–38 ng g^− 1 for MAME-SPE were obtained. The method was validated using Soxhlet extraction procedure.Both methods were applied to analyse target organochlorine pesticides in several seaweed samples and results were compared. These results show the great possibilities of combining MAME-SPE-HPLC-UV for the analysis of seaweed samples, improving the selectivity and sensitivity in the determination of organochlorine pesticides analysis for this kind of samples.     

Microwave-assisted purge-and-trap extraction device coupled with gas chromatography and mass spectrometry for the determination of five predominant odors in sediment,fish tissues,and algal cells

Off-flavors are among the most troublesome compounds in the environment worldwide. The lack of a viable theory for studying the sources, distribution, and effect of odors has necessitated the accurate measurement of odors from environmental compartments. A rapid and flexible microwave-assisted purge-and-trap extraction device for simultaneously determining five predominant odors, namely, dimethyltrisulfide, 2-methylisoborneol, geosmin, β-cyclocitral and β-ionone, from the primary sources and sinks is demonstrated. This instrument facilitates the extraction and concentration of odors from quite different matrices simultaneously. This device is a solvent-free automated system that does not require cleaning and is timesaving. The calibration curves of the five odor compounds showed good linearity in the range of 1–500 ng/L, with correlation coefficients above 0.999 (levels = 7) and with residuals ranging from approximately 77% to 104%. The limits of detection (S/N = 3) were below 0.15 ng/L in algae sample and 0.07 ng/g in sediment and fish tissue samples. The relative standard deviations were between 2.65% and 7.29% (n = 6). Thus the proposed design is ready for rapid translation into a standard analytical tool and is useful for multiple applications in the analysis of off-flavors.     

Toward use of a nano layered double hydroxide/ammonium pyrrolidine dithiocarbamate in speciation analysis: One-step dispersive solid-phase extraction of chromium species in human biological samples

Chromium is a controversial element with an important essentiality and toxicity. Depending on its different species, its speciation analysis in bio-origin matrices is of utmost importance. Ammonium pyrrolidine dithiocarbamate (APDC) and layered double hydroxide (LDH) nanoparticles, with the purpose of combining their outstanding performances, were served to speciate chromium ions in human biological samples. The as-obtained sorbent (nano LDH-APDC) - after characterization by X-ray diffraction (XRD), Fourier transform infrared (FT-IR) spectroscopy, thermal gravimetric analysis (TGA), and scanning electron microscopy (SEM) - was used as a novel pH-sensitive adsorbent in an integrated one-step dispersive solid-phase extraction (I-OS-DSPE), which combines the benefits of the air-assisted microextraction and dispersive solid-phase extraction methods. An interesting feature of the nano LDH-APDC sorbent is that it is dissolved in an aqueous solution when the pH of the solution is lower than 4. Thus the analyte elution step, as required in most of the sorbent-based extraction methods, was obviated by dissolving the sorbent in an acidic solution after extraction and separation from the sample solution. The Cr(VI) ions were first extracted, while the Cr(III) ions remained in the aqueous solution. The extract was then directly injected into a flame atomic absorption spectrometer with a micro-sampling introduction system, and the concentration of the Cr(III) ions was calculated by its subtraction from the total chromium ions present. Several variables including the pH (5), type and amount of the nanosorbent used (30 mg of nano (Zn-Al) LDH-APDC), number of extraction cycles (15 times), and elution conditions (200 µL of 6.0 mol L⁻¹ HNO₃) were investigated to achieve the maximum extraction efficiency. Under the optimum experimental conditions, the limit of detection, linear range, consumptive index, and enrichment factor for the Cr(VI) ions were 2.4 μg L⁻¹, 8.0–640 μg L⁻¹, 0.24, and 42.5 ± 1, respectively. These findings suggested that nano (Zn-Al) LDH-APDC could be regarded as a promising adsorbent for an efficient speciation of the chromium species in the human hair, nail, saliva, plasma, and urine samples.     

Evaluation of four sample treatments for determination of platinum in automotive catalytic converters by graphite furnace atomic absorption spectrometry

Conventional and microwave assisted digestion, both using aqua regia, alkaline fusion with lithium metaborate and aqueous slurries were evaluated as sample treatments for determination of Pt in automotive catalytic converters by Graphite Furnace Atomic Absorption Spectrometry (GF-AAS). Determination of platinum by GF-AAS in samples of the catalytic converter's substrates, prepared by the four methods described, indicates that the highest platinum concentration i.e. maximum Pt extraction in the range of 748 ± 15–998 ± 10 μg mL^− 1, is obtained for samples dissolved by alkaline fusion, closely followed by analysis of aqueous plus Triton X-100 slurries 708 ± 14–958 ± 10 μg mL^− 1, while neither one of the acid digestion procedures achieved total dissolution of the samples. Slurry analysis is thus shown to be a viable alternative and is recommended, based on its speed and ease of implementation. Aqueous standards calibration curves and the standard addition methods were also compared. The results showed that no appreciable matrix effects are present, regardless of the sample preparation procedure used. Precision of the measurements, expressed as percentage relative standard deviation, ranged between 2.5 to 4.9%. Accuracy of the results was assessed by recovery tests which rendered values between 98.9 and 100.9%.     

Determination of atorvastatin in human serum by salting out assisted solvent extraction and reversed-phase high-performance liquid chromatography–UV detection

A simple and rapid technique based on salting out assisted solvent extraction was developed for extraction of atorvastatin from serum sample and high performance liquid chromatography–UV was used for its detection. In the present study, 1.0 mL serum was extracted by 0.5 mL of acetonitrile and some parameters that can affect extraction such as type and volume of extraction solvent, type of salt, and pH were optimized. Under optimized experimental conditions, the calibration curve was found to be linear in the range of 0.001–10 ng mL⁻¹ in human serum and the correlation coefficient (R²) and the limits of detection were >0.99 and 0.0005 ng mL⁻¹, respectively. The accuracy of the method in terms of average recovery of the compound in spiked serum and water samples was better than 90%.     

Dithizone–chloroform single drop microextraction system combined with electrothermal atomic absorption spectrometry using Ir as permanent modifier for the determination of Cd in water and biological samples

A simple and sensitive method using dithizone–chloroform single drop microextraction has been developed for separation and preconcentration of trace Cd prior to its determination by electrothermal atomic absorption spectrometry with Ir as permanent modifier. Parameters, such as pyrolysis and atomization temperature, solvent type, pH, dithizone concentration, extraction time, organic drop volume, stirring rate and sample volume were investigated. Under the optimized conditions, a detection limit (3σ) of 0.7 ng/l and enrichment factor of 65 were achieved. The relative standard deviation was 7.4% (c = 0.2 μg/l, n = 5). The developed method has been applied to the determination of trace Cd in water samples and biological reference materials with satisfactory results.     

Direct determination of trace rare earth elements in ancient porcelain samples with slurry sampling electrothermal vaporization inductively coupled plasma mass spectrometry

A method for the direct determination of trace rare earth elements in ancient porcelain samples by slurry sampling fluorinating electrothermal vaporization inductively coupled plasma mass spectrometry was developed with the use of polytetrafluoroethylene as fluorinating reagent. It was found that Si, as a main matrix element in ancient porcelain sample, could be mostly removed at the ashing temperature of 1200 °C without considerable losses of the analytes. However, the chemical composition of ancient porcelain sample is very complicated, which makes the influences resulting from other matrix elements not be ignored. Therefore, the matrix effect of ancient porcelain sample was also investigated, and it was found that the matrix effect is obvious when the matrix concentration was larger than 0.8 g l^− 1. The study results of particle size effect indicated that when the sample particle size was less than 0.057 mm, the particle size effect is negligible. Under the optimized operation conditions, the detection limits for rare earth elements by fluorinating electrothermal vaporization inductively coupled plasma mass spectrometry were 0.7 ng g^− 1 (Eu)–33.3 ng g^− 1(Nd) with the precisions of 4.1% (Yb)–10% (La) (c = 1 μg l^− 1, n = 9). The proposed method was used to directly determine the trace rare earth elements in ancient porcelain samples produced in different dynasty (Sui, Ming and Qing), and the analytical results are satisfactory.     

Minimization of mass interferences in quadrupole inductively coupled plasma mass spectrometric (ICP-MS) determination of palladium using a flow injection on-line displacement solid-phase extraction protocol

A flow injection on-line displacement solid-phase extraction protocol was employed to minimize mass interferences with determination of palladium by inductively coupled plasma mass spectrometry (ICP-MS). The developed method involved in on-line complexing of Ag⁺ with pyrrolidine dithiocarbamate (PDC), presorption of the resultant Ag–PDC onto a microcolumn packed with the cigarette filter, displacement sorption of Pd²⁺ through loading the sample solution onto the microcolumn due to on-line displacement reaction between Pd²⁺ and the presorbed Ag–PDC, elution of the retained Pd²⁺ with 50 μL of ethanol for on-line ICP-MS detection. Interferences from co-existing heavy metal ions with lower stability of their PDC complexes relative to Ag–PDC were minimized/eliminated. No interferences from 5 mg L^− 1 Zn and 3 mg L^− 1 Pb for ¹⁰⁴Pd, 0.4 mg L^− 1 Cu for ¹⁰⁵Pd, 6 mg L^− 1 Zn and 2 mg L^− 1 Cd for ¹⁰⁶Pd, 6 mg L^− 1 Zn and 3 mg L^− 1 Cd for ¹⁰⁸Pd, and 2 mg L^− 1 Cd for ¹¹⁰Pd were observed for the determination of 100 ng L^− 1 Pd. The enhancement factors of 71–75, sample throughput of 23 samples h^− 1 and detection limits of 2.8–3.5 ng L^− 1 were achieved with the consumption of 3.0 mL of sample solution. The precision (RSD) for eleven replicate determinations of Pd at the 100 ng L^− 1 level was 1.8–2.7%. The developed method was applied to the determination of palladium in rock samples.     

Cu determination in crude oil distillation products by atomic absorption and inductively coupled plasma mass spectrometry after analyte transfer to aqueous solution

Cu was determined in a wide range of petroleum products from crude oil distillation using flame atomic absorption spectrometry (FAAS), electrothermal atomic absorption spectrometry (ETAAS) and inductively coupled plasma mass spectrometry (ICP-MS). Different procedures of sample preparation were evaluated: (i) mineralization with sulfuric acid in an open system, (ii) mineralization in a closed microwave system, (iii) combustion in hydrogen–oxygen flame in the Wickbold's apparatus, (iv) matrix evaporation followed by acid dissolution, and (v) acidic extraction. All the above procedures led to the transfer of the analyte into an aqueous solution for the analytical measurement step. It was found that application of FAAS was limited to the analysis of the heaviest petroleum products of high Cu content. In ICP-MS, the use of internal reference method (with Rh or In as internal reference element) was required to eliminate the matrix effects in the analysis of extracts and the concentrated solutions of mineralized heavy petroleum products. The detection limits (in original samples) were equal to, respectively, 10, 86, 3.3, 0.9 and 0.4 ng g^− 1 in procedures i–v with ETAAS detection and 10, 78, 1.1 and 0.5 ng g^− 1 in procedures i–iii and v with ICP-MS detection. The procedures recommended here were validated by recovery experiments, certified reference materials analysis and comparison of results, obtained for a given sample, in different ways. The Cu content in the analyzed samples was: 50–110 ng g^− 1 in crude oil, < 0.4–6 ng g^− 1 in gasoline, < 0.5–2 ng g^− 1 in atmospheric oil, < 6–100 ng g^− 1 in heavy vacuum oil and 140–300 ng g^− 1 in distillation residue.     

Determination of Hg(II) in waters by on-line preconcentration using Cyanex 923 as a sorbent — Cold vapor atomic absorption spectrometry

Using a solid phase extraction mini-column home-made from a neutral extractant Cyanex 923, inorganic Hg could be on-line preconcentrated and simultaneously separated from methyl mercury. The preconcentrated Hg (II) was then eluted with 10% HNO₃ and subsequently reduced by NaBH₄ to form Hg vapor before determination by cold vapor atomic absorption spectrometry (CVAAS). Optimal conditions for and interferences on the Hg preconcentration and measurement were at 1% HCl, for a 25 mL sample uptake volume and a 10 mL min^− 1 sample loading rate. The detection limit was 0.2 ng L^− 1 and much lower than that of conventional method (around 15.8 ng L^− 1). The relative standard deviation (RSD) is 1.8% for measurements of 40 ng L^− 1 of Hg and the linear working curve is from 20 to 2000 ng L^− 1 (with a correlation coefficient of 0.9996). The method was applied in determination of inorganic Hg in city lake and deep well water (from Changchun, Jilin, China), and recovery test results for both samples were satisfactory.     

Chiral stability-indicating HPLC method for analysis of arotinolol in pharmaceutical formulation and human plasma

An enantioselective stability-indicating high performance liquid chromatographic method was developed for the analysis of arotinolol in standard solution. The degradation behaviour of arotinolol was investigated under different stress conditions recommended by International Conference on Harmonization (ICH). Resolution of the drug and complete separation from its degradation products were successfully achieved on a Chirobiotic V column, using UV detector set at 315 nm, polar organic mobile phase (POM) consisting of methanol:glacial acetic acid:triethylamine, 100:0.02:0.03, (v/v/v), and a flow rate of 1 ml/min. The drug was subjected to oxidation, hydrolysis, photolysis, and heat to apply stress conditions. The drug was found to degrade in alkaline, acidic, oxidative conditions and when exposed to heat. The drug was stable to sunlight. The method reported here has also been successfully applied to pharmaceutical formulation and to human plasma that spiked with stock solutions of arotinolol enantiomers.Arotinolol enaniomers were recovered from plasma by using liquid–liquid extraction procedure with ethyl ether. The method was highly specific, where degradation products and coformulated compounds did not interfere, and was sensitive with good precision and accuracy and was linear over the range of 50–400 ng/ml (R² > 0.9981) with a detection limit of 20 ng/ml for each enantiomer. The mean extraction efficiency for arotinolol was in the ranges 96–104% for each enantiomer. The mean relative standard deviation (RSD) of the results of within-day precision and accuracy of the drug were ?7.1%. There was no significant difference between inter- and intra-day studies for each enantiomers which confirmed the reproducibility of the assay. The overall recoveries of arotinolol enantiomers from pharmaceutical formulations were in the ranges 97.6–101.8%.     

Evaluation of microwave and ultrasound extraction procedures for arsenic speciation in bivalve mollusks by liquid chromatography–inductively coupled plasma-mass spectrometry

Liquid chromatography–inductively coupled plasma-mass spectrometry (LC–ICP-MS) was used for arsenic speciation analysis in tissues of bivalve mollusks (Anomalocardia brasiliana sp. and Macoma constricta sp.). Microwave and ultrasound radiation, combined with different extraction conditions (solvent, sample amount, time, and temperature), were evaluated for As-species extraction from the mollusks' tissues. Accuracy, extraction efficiency, and the stability of As species were evaluated by analyzing certified reference materials (DORM-2, dogfish muscle; BCR-627, tuna fish tissue; and SRM 1566b, oyster tissue) and analyte recovery tests. The best conditions were found to be microwave-assisted extraction using 200 mg of samples and water at 80 °C for 6 min. The agreement of As-species concentration in samples ranged from 97% to 102%. Arsenobetaine (AsB) was the main species present in bivalve mollusk tissues, while monomethylarsonic acid (MMA) and arsenate (As(V)) were below the limit of quantification (0.001 and 0.003 μg g^− 1, respectively). Two unidentified As species also were detected and quantified. The sum of the As-species concentration was in agreement (90 to 104%), with the total As content determined by ICP-MS after sample digestion.     

Characterization of a capillary spray cell for easy analysis of extracts of biological samples

We present a very simple electrospray unit, a capillary spray cell, for easy analysis of small (10–50 μL) sample aliquots. The sample, e.g., an unfiltered extract, is injected to a small sample cell, made of alumina and containing a short fused silica capillary mounted in its side. By the application of a 5 kV potential between the sample cell and the entrance orifice of a mass spectrometer with an atmospheric pressure interface, the sample is dragged out of the cell at a rate of a few μL/min and an electrospray is generated at the tip of the silica capillary. The capillary spray cell benefits from a high internal diameter (up to 250 μm) and very easy and inexpensive replacement of the capillary, which makes the sprayer well suited for analysis of unfiltered extracts. We demonstrate the direct analysis of extracts from plants and insects. In quantitative measurements using internal standards, a relatively high sensitivity (low ng/mL) is obtained together with good linearity (R² = 0.998) in the range of 10–1000 ng/mL. The capillary spray cell is also suited for use with field portable mass spectrometers, since no syringe pump or nebulizer gas is needed. Furthermore, the capillary spray cell is easily manufactured by most mechanical workshops.     

Ultra-preconcentration and determination of thirteen organophosphorus pesticides in water samples using solid-phase extraction followed by dispersive liquid–liquid microextraction and gas chromatography with flame photometric detection

An ultra-preconcentration technique composed of solid-phase extraction (SPE) and dispersive liquid–liquid microextraction (DLLME) coupled with gas chromatography–flame photometric detection (GC–FPD) was used for determination of thirteen organophosphorus pesticides (OPPs) including phorate, diazinon, disolfotane, methyl parathion, sumithion, chlorpyrifos, malathion, fenthion, profenphose, ethion, phosalone, azinphose-methyl and co-ral in aqueous samples. The analytes were collected from large volumes of aqueous solutions (100 mL) into 100 mg of a SPE C₁₈ sorbent. The effective variables of SPE including type and volume of elution solvent, volume and flow rate of sample solution, and salt concentration were investigated and optimized. Acetone was selected as eluent in SPE and disperser solvent in DLLME and chlorobenzene was used as extraction solvent. Under the optimal conditions, the enrichment factors were between 15,160 and 21,000 and extraction recoveries were 75.8–105.0%. The linear range was 1–10,000 ng L^?1 and limits of detection (LODs) were between 0.2 and 1.5 ng L^?1. The relative standard deviations (RSDs) for 50 ng L^?1 of OPPs in water with and without an internal standard, were in the range of 1.4–7.9% (n = 5) and 4.0–11.6%, respectively. The relative recoveries of OPPs from well and farm water sat spiking levels of 25 and 250 ng L^?1 were 88–109%.     

Selenium content in selected foods from the Saudi Arabia market and estimation of the daily intake

This study was conducted to create a selenium database for the representative food items in Saudi diet and to estimate the dietary selenium intake of Saudi Arabians. Three samples for each food item selected were purchased from the markets. Each pooled sample was analyzed in triplicate by ICP–MS after thorough homogenization. The rich sources of selenium were meats (0.216–0.658 μg/g), eggs (0.226 μg/g) and cereals and cereals products (0.043–0.165 μg/g). Vegetables and fruits contained trace amounts of selenium (0.001–0.067 μg/g). The major food sources of selenium intake were cereals and cereals products (30.2%), legumes (24.7%) and meats (20%). The daily intake of Se was calculated taking into account the concentration of this element in the edible part and the daily consumption data which were derived from two sources, (a) the food balance sheet of KSA given by Food and Agriculture Organization (FAO) and (b) from questionnaires distributed among 200 families in Jeddah. The results showed that the daily intake of Se according to the two sources is 75.00–121.65 μg/person/day.     

Occurrence of ochratoxin A in bread consumed in Morocco

One hundred samples of commercial bread purchased from January to October (2006) from retail bakeshops in five different cities (Rabat, Témara, Salé, Casablanca and Meknès) in Morocco were surveyed for the presence of ochratoxin A (OTA) using liquid chromatography coupled to fluorescence detection. The identification of OTA in positive bread samples was confirmed by methyl ester derivatization. Analytical results showed that forty eight (48%) samples were positive with OTA greater than the limit of quantification (LOQ = 0.051 ng/g). Levels of OTA in positive samples ranged between 0.14 and 149 ng/g. The average contamination of bread samples with OTA was 13 ± 1.5 ng/g. The highest frequency of positive samples (61.5%) and the most contaminated sample (149 ng/g) were found in bread commercialized in the Casablanca area. Twenty six of the positive samples exceeded the maximum level of 3 ng/g set by European regulations for OTA in cereals and derivatives. Based in the results presented in this study, the estimated daily intake of OTA from bread was 126 ng/kg bw/day. The present paper is the first ever drafted on the natural occurrence of OTA in bread consumed in Morocco. Data on the daily intake of OTA by the Moroccan population are also estimated for the first time.     

Monolithic molecular imprinted polymer fiber for recognition and solid phase microextraction of ephedrine and pseudoephedrine in biological samples prior to capillary electrophoresis analysis

A novel capillary electrophoresis (CE) method coupled with monolithic molecular imprinted polymer (MIP) fiber based solid phase microextraction (SPME) was developed for selective and sensitive determination of ephedrine (E) and pseudoephedrine (PE). With in situ polymerization in a silica capillary mold and E as template, the MIP fibers could be produced in batch reproducibly and each fiber was available for 50 extraction cycles without significant decrease in extraction ability. Using the MIP fiber under optimized extraction conditions, CE detection limits of E and PE were greatly lowered from 0.20 to 0.00096 μg/mL and 0.12 to 0.0011 μg/mL, respectively. Analysis of urine and serum samples by the MIP-SPME-CE method was also performed, with results indicating that E and PE could be selectively extracted. The recoveries and relative standard deviations (RSDs) for sample analysis were found in the range of 91–104% and 3.8–9.1%, respectively.     

Stability-indicating HPLC method for the determination of nicardipine in capsules and spiked human plasma. Identification of degradation products using HPLC/MS

In this stability-indicating, reversed-phase high-performance liquid chromatographic method for nicardipine (NIC), forced degradation has been employed and the formed degradants were separated on a C18 (150 mm × 3.9 mm, 5 μm) analytical column using a mobile phase consisted of 70% methanol: acetic acid containing 0.01 M triethylamine with pH 4. The flow rate was 1.0 mL/min and the photodiode array detection wavelength was 353 nm. Forced degradation of the drug was carried out under acidic, basic, photolytic, and oxidative stress conditions. Chromatographic peak purity data indicated no co-eluting peaks with the main peaks. This method resulted in the detection of seven degradation products. Among these, two major degradation products from basic hydrolysis, one from oxidation by H₂O₂ and four from photolytic stress were identified by mass spectral data. A good linear response was achieved over the range of 0.5–40 μg/mL with a limit of detection (LOD) of 0.011 μg/mL and limit of quantification (LOQ) of 0.036 μg/mL. The suggested method was successfully applied for the analysis of NIC in its commercial capsules, with mean% recovery value of 100.11 ± 2.26%. The method was extended to the in vitro determination on NIC in spiked human plasma samples with mean% recovery of 99.04 ± 5.67%. The suggested method was utilized to investigate the kinetics of photolytic induced degradation.