Ultrasound and microwave-assisted extraction of metals from sediment: a comparison with the BCR procedure

In this paper we investigate alternatives to mechanical stirring for the extraction of the mobile fraction of metals from sediment, and analyze whether these techniques can reduce extraction time and improve reproducibility. We compare the quantities of metal extracted from BCR601 and BCR701 certified sediments using ultrasound bath, microwave-assisted extraction and the first step in the certified BCR sequential extraction procedure. Some environmentally important not-certified metals such as As, Mn, Co, Fe and Al have been included in this study. In the case of microwave-assisted extraction, we compare tests in which samples are exposed to constant, low power irradiation with tests using pulsed high power.

In the tests using the ultrasound bath, less metal was extracted than with the other extractive techniques and standard deviations were comparable to those obtained with the BCR procedure; in assays using microwaves at constant power, extraction efficiencies were different for different metals and for different reference materials and, in some cases, standard deviations were higher than those for the reference method. In contrast, tests with microwaves and constant temperature produced encouraging results: R.S.D.s lay in the 2–4% range, both for certified and not-certified metals; these values are very low compared to those for the reference method. Extraction efficiencies for certified metals were close to 100% for Cd, Zn, Cu and Ni and around 80% for Pb and Cr.     

Element determination in medieval soil samples by total reflection X-ray fluorescence analysis

An aqua regia extraction procedure for heavy metals in soils optimised for total reflection X-ray fluorescence analysis is presented. The procedure is applied to 92 soil samples of medieval layers from the city area of Dortmund. Sixteen elements (P, S, K, Ca, Ti, Cr, Mn, Fe, Ni, Cu, Zn, Rb, Sr, Ag, Sn, and Pb) were used to characterise 17 sample sites. The results are projected onto the medieval urban structure of Dortmund. Two sites loaded with non-ferrous heavy metal could be detected and correlated with archaeological data. The efficiency and repeatability of the proposed extraction procedure is discussed.     

Determination of Al, Cu, Fe, Mn, Pb and Zn in certified reference materials using the optimized BCR sequential extraction procedure

Sequential extraction procedures are widely used to characterize the fractionation of metal species in solid media. With the variety of different sequential procedures used in environmental and geochemical exploration studies, it is difficult to compare results between studies. Thus, harmonization and standardization are required to provide greater inter-study comparability for fraction-specific metals. In this study, the optimized BCR three-step sequential extraction procedure is applied to five certified reference materials (SRM 2710, SRM 2711, CRM 483, CRM 601 and CW 7). Four fractions are reported, acid extractable, reducible, oxidizable, and residual for Al, Cu, Fe, Mn, Pb and Zn. The objectives of this study were to characterize experimental precision and/or accuracy and to establish baseline data of fraction-specific element concentrations for future studies applying the optimized BCR three-step extraction procedure. The optimized procedure was found to be precise (typically <5%) for all metals in all fractions. Accuracy was acceptable (typically ±15% relative to published indicative values for Cu, Pb and Zn for CRM 483 and CRM 601) for all individual fractions. Detailed fraction-specific concentration data are presented, based on five replicates, for the first time using the optimized procedure for Al, Fe and Mn in CRM 483 and CRM 601, and for Al, Cu, Fe, Mn, Pb and Zn in SRM 2710, SRM 2711 and CW 7.     

Extraction and exchange behavior of metal species in therapeutically applied peat

The binding and availability of metals (Al, Ca, Cd, Co, Cr, Cu, Fe, Mg, Mn, Ni, Pb, Zn) in therapeutically applied peat (Grosses Gifhorner Moor, Sassenburg/North Germany) was characterized by means of a versatile extraction approach. Aqueous extracts of peat were obtained by a standardized batch equilibrium procedure using high-purity water (pH 4.5 and 5.0), 0.01 mol l(-1) calcium chloride solution, 0.01 mol l(-1) ethylenediaminetetraacetic acid (EDTA) and 0.01 mol l(-1) diethylenetriamine pentaacetic acid (DTPA) solution as metal extractants. In addition, the availability of peat-bound metal species was kinetically studied by collecting aliquots of extracts after different periods of extraction time (5, 10, 15, 30, 60 and 120 min). Metal determinations were performed by atomic spectrometry methods (AAS, ICP-OES) and dissolved organic matter (DOM) was characterized by UV/Vis measurements at 254 and 436 nm, respectively. Of the extractants studied Ca, Mg and Mn were the most available metals, in contrast to peat-bound Fe and Al. The relative standard deviation s(r) of the developed extraction procedures was mostly in the range of 4 to 20%, depending on the metal and its concentration in peat. A pH increase favored the extraction of metals and DOM from peat revealing complex extraction kinetics. Moreover, a competitive exchange between peat-bound metal species and added Cu(II) ions showed that >100 mg of Cu(II) per 50 g wet peat was necessary to exchange the maximum of bound metals (e.g. 21.8% of Al, 3.9% of Fe, 79.0% of Mn, 81.9% of Sr, related to their total content).     

Pressurized liquid extraction as a novel sample pre-treatment for trace element leaching from biological material

Pressurized liquid extraction (PLE), commonly used for organic compounds extraction, has been applied for trace element leaching from marine biological material in order to determine major and trace elements (Al, As, Cd, Co, Cu, Fe, Hg, Li, Mn, Pb, Se, Sr, V and Zn). The released elements by formic acid PLE have been evaluated by inductively coupled plasma-optical emission spectrometry (ICP-OES). Different variables, such as formic acid concentration, extraction temperature, static time, extraction steps, pressure, mean particle size and diatomaceous earth (DE) mass/sample mass ratio were simultaneously studied by applying an experimental design approach (Plackett-Burman design (PBD) and central composite design (CCD)). Results showed that the extraction temperature was statistically significant (confidence interval of 95%) for most of the elements (high metal releasing was achieved at high temperatures). In addition, formic acid concentration was also statistically significant (confidence interval of 95%) for metals such as Cd and Cu. Most of the metals can be extracted using the same PLE operating conditions (formic acid concentration of 1.0 M, extraction temperature at 125 °C, static time of 5 min, one extraction step, extraction pressure at 500 psi and DE mass/sample mass ratio of 2). Taking in mind PLE requirements at the optimised operating conditions (125 °C), a time of 6 min is needed to pre-heat the cell. Therefore, the PLE assisted multi-element leaching is completed after 12 min. Analytical performances, such as limits of detection and quantification, repeatability of the over-all procedure and accuracy, by analysing GBW-08571, DORM-2, DOLT-3 and TORT-2 certified reference materials, were finally assessed.     

Comparison of ultrasound-assisted extraction and microwave-assisted digestion for determination of magnesium, manganese and zinc in plant samples by flame atomic absorption spectrometry

In this paper, a sample preparation method based on acid extraction of magnesium, manganese and zinc from plant tissue by means of high intensity probe ultrasonication is described. Acid extracts obtained upon sonication were directly nebulised into an air-acetylene flame for fast metal determination by atomic absorption spectrometry. Parameters influencing extraction such as sonication time, ultrasound amplitude, sample mass, particle size, extractant composition and volume were fully optimised. Optimum conditions for metal extraction were as follows: a 3-min sonication time, a 30% ultrasonic amplitude, a 0.1-g sample mass, a particle size less than 50 mum, a 0.3% m/v HCl concentration in the extractant solution and a 5-ml extractant volume. Six plant samples used in the human diet were analysed, the concentration range of the three metals approximately being in the range of 1500-3000 mug g(-1) for Mg, 30-735 mug g(-1) for Mn and 20-45 mug g(-1) for Zn. Limits of detection corresponding to the ultrasound-assisted extraction method were 0.10, 1.26 and 0.65 mug g(-1) for Mg, Mn and Zn, respectively. Between-batch precision, expressed as R.S.D., was about 0.5, 1.5 and 1% for Mg, Mn and Zn, respectively. Analytical results for the three metals by ultrasound-assisted extraction and microwave-assisted digestion showed a good agreement, thus indicating the possibility of using mild conditions for sample preparation instead of intensive treatments inherent with the digestion method. The advantages and drawbacks of ultrasound-assisted extraction in respect to the microwave-assisted digestion are discussed.     

Determination of nonylphenol polyethoxylates in household detergents by high-performance liquid chromatography

The binding of metals to proteins in blood fractions was investigated applying hydrophobic interaction chromatography (HIC) for protein separation and graphite furnace atomic absorption spectrometry (GFAAS) as the element specific detector. For the semi-preparative separation of metalloproteins in erythrocytes and blood plasma, a HIC column (Fractogel EMD Phenyl I (S) 150 mm×10 mm I.D.) was adapted. The separation column was calibrated with the same four standard proteins as used in Pomazal et al. [Analyst 124 (1999) 657]. The sample injection volume and the ammonium sulphate gradient set-up were optimized: 20 or 200 μl, respectively, of blood plasma and of lysed erythrocytes were injected. The separated proteins were collected in 4-ml fractions and analyzed by GFAAS off-line. An optimization of the GFAAS measuring parameters for Cu, Mn, Fe, Zn, Co, Ni, and Cr was performed. For each element, a specific temperature program was optimized with respect to the matrix of the HIC eluate (0.02 M NaH₂PO₄, 1.8 M (NH₄)₂SO₄). The obtained metal profiles of the eluate were compared with the HIC chromatograms. The limits of detection (LOD) for the elements by GFAAS were: 0.5 ng Cu/ml; 0.2 ng Mn/ml; 1 ng Fe/ml; 0.2 ng Zn/ml; 0.12 ng Co/ml; 0.2 ng Ni/ml; 0.16 ng Cr/ml. The GFAAS method enabled the detection of the proteins of interest via the metals.     

Determination of chromium,manganese and vanadium in sediments and soils by modifier—free slurry sampling electrothermal atomic absorption spectrometry

Slurried sediment and soil samples of the certified reference materials with a highly elevated level of the metals of interest (Mn, Cr and V) were analysed by electrothermal atomic absorption spectrometry (ETAAS) with Zeeman effect background correction. The method of slurry preparation and time-temperature programmes were optimized and, finally, the use of chemical modifiers was not necessary. The effect of alternate spectral lines and gas mini-flows on characteristic masses of analytes was studied. The homogeneity of samples and the influence of short sample grinding were also discussed. The simple, aqueous standard based calibration graphs (except Mn at the concentration > 1000 mg kg⁻¹) were applied for the quantification of results. The results of determinations obtained by slurry sampling agreed well with the cetified values, and the relative standard deviations (RSDs) for the over-all analytical procedure repeatability (at slurries concentration level about 2 mg/2 ml) were less than 9.5%, except manganese (10.4%).     

Utilization of optimized BCR three-step sequential and dilute HCl single extraction procedures for soil-plant metal transfer predictions in contaminated lands

The prediction of soil metal phytoavailability using the chemical extractions is a conventional approach routinely used in soil testing. The adequacy of such soil tests for this purpose is commonly assessed through a comparison of extraction results with metal contents in relevant plants. In this work, the fractions of selected risk metals (Al, As, Cd, Cu, Fe, Mn, Ni, Pb, Zn) that can be taken up by various plants were obtained by optimized BCR (Community Bureau of Reference) three-step sequential extraction procedure (SEP) and by single 0.5 mol L(-1) HCl extraction. These procedures were validated using five soil and sediment reference materials (SRM 2710, SRM 2711, CRM 483, CRM 701, SRM RTH 912) and applied to significantly different acidified soils for the fractionation of studied metals. The new indicative values of Al, Cd, Cu, Fe, Mn, P, Pb and Zn fractional concentrations for these reference materials were obtained by the dilute HCl single extraction. The influence of various soil genesis, content of essential elements (Ca, Mg, K, P) and different anthropogenic sources of acidification on extraction yields of individual risk metal fractions was investigated. The concentrations of studied elements were determined by atomic spectrometry methods (flame, graphite furnace and hydride generation atomic absorption spectrometry and inductively coupled plasma optical emission spectrometry). It can be concluded that the data of extraction yields from first BCR SEP acid extractable step and soil-plant transfer coefficients can be applied to the prediction of qualitative mobility of selected risk metals in different soil systems.     

Simultaneous determination of traces of heavy metals by solid-phase spectrophotometry

A coupling sensitive solid phase spectrophotometric (SPS) procedure for determination of traces of heavy metals (Me-SPS) and multicomponent analysis by multiple linear regressions (MA), a simple methodology for simultaneous determination of metals in mixtures was inaugurated. The Me-SPS procedure is based on sorption of heavy metals on PAN-resin and direct absorbance measurements of colour product Me-PAN sorbed on a solid carrier in a 1-mm cell. This methodology (Me-SPS-MA) was checked by simultaneous determination of metals in synthetic mixtures with different compositions and contents of metals important in pharmaceutical practice: Zn, Pb, Cd, Cu, Co, and Ni. Good agreement between experimental and theoretical amounts of heavy metals is obtained from the recovery test (78.3–110.0%). The proposed method enables determination of particular metal ion at the ng mL⁻¹ level and it was successfully applied to the determination impurities from heavy metal traces in pharmaceutical substances (Cu in ascorbic acid, Pb in glucose, and Zn in insulin). The proposed procedure could be possible contribution to the development of pharmacopoeial methodology for a heavy metals test.     

Determination of arsenic(III) and arsenic(V) by electrothermal atomic absorption spectrometry after complexation and sorption on a C-18 bonded silica column

A flow injection procedure for the separation and pre-concentration of inorganic arsenic based on the complexation with ammonium diethyl dithiophosphate (DDTP) and sorption on a C-18 bonded silica gel minicolumn is proposed. During the sample injection by a time-based fashion, the As³⁺-DDTP complex is stripped from the solution and retained in the column. Arsenic(V) and other ions that do not form complexes are discarded. After reduction to the trivalent state by using potassium iodide plus ascorbic acid, total arsenic is determined by electrothermal atomic absorption spectrometry (ETAAS). Arsenic(V) concentration can be calculated by difference. After processing 6 ml sample volume, the As³⁺-DDTP complexes were eluted directly into the autosampler cup (120 μl). Ethanol was used for column rinsing. Influence of pH, reagent concentration, pre-concentration and elution time and column size were investigated. When 30 μl of eluate plus 10 μl of 0.1% (w/v) Pd(NO₃)₂ were dispensed into the graphite tube, analytical curve in the 0.3–3 μg As l⁻¹ range was obtained (r=0.9991). The accuracy was checked for arsenic determination in a certified water, spiked tap water and synthetic mixtures of arsenite and arsenate. Good recoveries (97–108%) of spiked samples were found. Results are precise (RSD 7.5 and 6% for 0.5 and 2.5 μg l⁻¹, n=10) and in agreement with the certified value of reference material at 95% confidence level.     

Pressure assisted chelating extraction: a novel technique for digesting metals in solid matrices

This work describes a novel technique for the digestion of metals in solid matrices. The technique is called pressure assisted chelating extraction (PACE). In a typical procedure, a solid sample is placed in a stainless steel cell and is mixed with appropriate chelating agents. Using a programmed sequence of temperature, static time, pressure and thermal equilibration available in ASE 200, the metal is removed under moderate temperature (up to 200 degrees C) and pressure (up to 3000 psi). PACE achieves metal recovery that is equivalent to that of wet digestion techniques and also provides for a clean and safe operation by substituting the strong acids commonly used during wet digestion with chelating agents. It uses less solvents and significantly less time (minutes vs. hours) for metal digestion. PACE has been validated using certified standard reference materials (SRMs) including industrial sludge, buffalo river sediments and coal fly ash. The total time required to remove metals was approximately 20 min. Results show that the PACE system provides an ideal platform for efficient, rapid, and safe metal digestion. Good agreement between measured and reference values for Pb, Mn, and Cu were found with recoveries averaging between 80 and 101% and a relative standard deviation of less than 5%. This approach may provide an alternative digestion technique for environmental samples, alloys, biological materials and samples of geological importance. The potential advantage offered lies in non-destruction of the sample, automation and the exclusion of concentrated mineral acids during the digestion procedure.     

Microanalytical flow-through method for assessment of the bioavailability of toxic metals in environmental samples

The application of a recently proposed microanalytical flow-through system for on-line sequential extraction of heavy metals from solid samples of environmental interest is described. Using various extraction schemes (a nitric acid scheme, a two-stage extraction scheme using two reagents applied in the BCR procedure) and comparison with the common batch sequential BCR procedure, the suitability of the system for fast screening of solid environmental samples is demonstrated. By pumping leaching agents sequentially through the sample held in a micro cartridge, the different metal fractions present can be assessed in less than an hour. Method evaluation was performed using SRM 1648 urban particulate matter and BCR 701 lake sediment reference material certified for extractable metals. The need for and design of laboratory internal reference material suitable for simulating the natural (dynamic) processes of metal release into the environment is also discussed. For the first time correlation is sought between fractionation techniques and physiologically based methods for assessment of the bioaccessibility of metals in biomatrices.     

Fast sample preparation involving MASE and coupled column normal phase liquid chromatography for the rapid trace analysis of dioxins in air-dust samples from fire catastrophe emissions

A new approach has been developed and tested for the urgent analysis of dioxins in samples of air-dust filters originating from catastrophe emissions. The procedure consists of a fast extraction of the sample with microwave solvent extraction (MASE) and acetone as solvent followed by a fast cleanup of the extract with normal phase coupled column liquid chromatography (LC/LC).

The multi-dimensional LC/LC system employs a 50 mm×4.6 mm i.d. column packed with 3 μm silica and a 150 mm×4.6 mm i.d. column packed with 5 μm PYE as the first and second analytical column, respectively. Iso-hexane is used on both columns to perform cleanup and dichloromethane to perform efficient back-flush elution of the compounds from the second column. The obtained polarity-based separation in the first dimension and molecular-structure based separation in the second dimension provides a fast and powerful cleanup.

Validation was done by analysing samples of homemade RIVM air-dust with aged residues (n=8, spiking level about 15 pg mg⁻¹ per compound) of dioxins/furans and samples of reference Urban Dust SRM 1649a (n=4) with both the new approach and the existing conventional procedure and were instrumentally analyzed with capillary gas chromatography and high resolution mass spectrometric detection (GC/HRMS).

In comparison to the existing conventional procedure, the new approach reduces sample processing from several days to several hours per sample.

As regards the aged-residue air-dust samples, the new method shows a good accuracy, precision and high selectivity providing a performance in good agreement with the existing procedure. In SRM air-dust, the concentration of a few compounds obtained by the new method was below (10–50%) the certified value.     

Relationship between vegetable metal and soil-extractable metal contents by the BCR sequential extraction procedure: chemometrical interpretation of the data

The contents of heavy metals in soil and vegetable samples collected from an urban garden in Kayseri, Turkey, were investigated. Both wet- and dry-ashing methods were used for dissolving vegetable samples. A sequential extraction procedure proposed by the Commission of the European Communities, Community Bureau of Reference (now superseded by the Standards, Measurement and Testing Programme, SM&T) was applied to the soil samples to extract the metals which are present in exchangeable and acid soluble (i.e. bound to carbonates), reducible (bound to Fe/Mn oxides), and oxidisable forms (bound to organic matter and sulphides) in the soil samples. Trace metals in the soil and vegetable samples were determined using flame atomic absorption spectrometry (FAAS). The total metal contents acquired by summing of metal levels in all the sequential extraction steps were compared with pseudo-total metal levels obtained with aqua regia for all the soil samples. The recovery values obtained by proportioning the results obtained by the BCR procedure to those of the pseudo-total digestion were found to be satisfactory. The limits of detection for the elements investigated were in the range of 0.04 to 0.59?µg?mL^?1 for all the extraction stages of the BCR procedure. Similarities among the variables were identified by correlation analysis, principal component analysis and hierarchical cluster analysis. The relationship between the vegetable metal and soil-extractable metal concentrations was examined in order to evaluate the bioavailability of metals.     

Determination of lead and manganese in biological samples and sediment using slurry sampling and flame atomic absorption spectrometry

A procedure was developed for the determination of lead (Pb) and manganese (Mn) using slurry sampling. The two elements were detected using flame atomic absorption spectrometry with a slotted tube atom trap. Slurries were prepared by adding nitric acid solution (0.30%, w/v) to a powdered sample (0.10 g). After homogenization by ultrasonic bath for 15 min, the slurries were introduced directly into the detection equipment. Some conditions of the procedure were evaluated, such as acid concentration, presence of surfactants, and sonication time. Under optimized conditions, the LODs and LOQs achieved were 0.8 and 2.6 microg/g for Pb and 0.5 and 1.6 microg/g for Mn, respectively. The precision obtained varied between 3.1 and 5.8% (Mn), and 2.6 and 5.4% (Pb) for slurries of shrimp and sediment. The analytical curves were established using aqueous standards in nitric acid solutions. The accuracy of the method was assessed through the determination of Pb and Mn in the following certified reference materials: ERM-CE 278 (mussel tissue), CRM 397 (human hair), and SRM 1646a (estuarine sediment). The proposed procedure was successfully applied to the determination of Pb and Mn in six samples of shrimp powder, seasoning, and river sediment. The levels of Mn detected varied from 2.2 to 71.3 microg/g; Pb was detected in only one sediment sample (4.3 microg/g).     

Capillary electrophoresis of methylmercury with injection by sample stacking

A procedure for separation and quantitation of methylmercury by capillary electrophoresis using sample stacking as the injection technique is presented. The CE conditions have been optimized in order to separate the methylmercury from the excess cysteine peak and to concentrate large volumes of sample obtaining a low detection limit. Under the proposed operational conditions, the detection limit (S/N = 3) was 12 ng g⁻ and the limit of quantitation (S/N = 10) was 20 ng g⁻¹ with a linear range of 20–100 ng g⁻¹ (as methylmercury in samples). The method was tested using different reference materials with a certified methylmercury content.     

Statistical design-principal component analysis optimization of a multiple response procedure using cloud point extraction and simultaneous determination of metals by ICP OES

A procedure has been developed for the simultaneous determination of traces amounts of Cd, Cr, Cu, Mn, Ni and Pb from saline oil-refinery effluents and digested vegetable samples using inductively coupled plasma optical emission spectrometry (ICP OES). The procedure is based on cloud point extraction (CPE) of these metals as 2-(bromo-2-pyridylazo)-5-diethyl-amino-phenol (Br-PADAP) complexes into a micellar phase of octylphenoxypolyethoxyethanol (Triton X-114). Optimization of the procedure was performed by response surface methodology (RSM) using a Doehlert design. Principal components (PC) were used to simplify the multiple response analysis. A response surface for the first PC score is useful in determining the optimum conditions for the Cd, Cr, Cu, Mn and Pb determinations whereas the second PC is highly correlated with the Ni response. Improvement factors of 22, 36, 46, 25, 65 and 39, along with limits of detection (3σ_B) of 0.081, 0.79, 0.38, 0.83, 0.28 and 0.69 μg L⁻¹, and precision expressed as relative standard deviation (%R.S.D., n = 8, 20.0 μg L⁻¹) of 1.5, 2.2, 3.5, 2.6, 2.5 and 2.5 were achieved for Cd, Cr, Cu, Mn, Ni and Pb, respectively. The accuracy was evaluated by spike tests in oil-refinery effluent samples and analysis of a vegetable certified reference material (NIST 1571, orchard leaves). Results found were in agreement with certified values.     

Investigation of heavy-metal uptake by vegetables growing in contaminated soils using the modified BCR sequential extraction method

The heavy metal (Cu, Fe, Co, Ni, Cd, Cr, Pb, Zn, and Mn) concentrations in soils and in vegetable samples, i.e. lettuce (Lactuca sativa L.), parsley (Petroselinum crispum), dill (Anethum graveolens), and onion (Allium cepa L.), taken from three urban vegetable gardens in Kayseri, Turkey, were determined by FAAS. The modified three-step sequential extraction procedure proposed by the European Bureau of References (BCR), now the Standards, Measurements and Testing Programme, was used in order to evaluate trace elements mobility in soil samples, and heavy-metal uptake by vegetables. Three operationally defined fractions were isolated using the BCR procedure: acid extractable (i.e. bound to carbonates), reducible (bound to Fe/Mn oxides), and oxidizable (bound to organic matter and sulphides). The vegetable samples were prepared to analysis using the wet-ashing procedure. To estimate the accuracy of the method used in analysis of the vegetable samples, the standard reference material (NIST SRM 1573a, Tomato leaves) was used. The results of recovery for all the elements were relatively satisfactory (87.7–108%). For the soil samples, the recovery values were calculated by proportioning the sum of the steps of the BCR procedure to those of the pseudototal digestion (i.e. aqua regia). In soils, the mobility of heavy metals followed the order Mn>Cd>Cu>Pb>Zn>Cr>Ni>Co>Fe. The relationship between the vegetable–metal and soil–extractable metal concentrations was examined in order to evaluate the bioavailability of metals, and the positive correlation, especially for the first (i.e. water, acid-soluble and exchangeable fraction) and for the third (i.e. oxidizable fraction) extraction steps, was obtained.     

Preconcentration and matrix separation of precious metals in geological and related materials using metalfix-chelamine resin prior to inductively coupled plasma mass spectrometry

A method for determining Au, Pt, Pd, Ir and Rh in ores and silicates and Fe-formation rocks is described. Sample decomposition was carried out with aqua regia and HF, followed by fusion of any insoluble residue with Na₂2O₂ in a glassycarbon crucible. The precious metals were separated, in 1.2 mol dm⁻³ HCl media, from the matrix elements by ion-exchange, using a mini-column with tetraethylenepentamine (metalfix-chelamine) resin. The resin was destroyed with HNO₃ and H₂O₂ in a high-pressure vessel assisted by microwave heating, and the precious elements were determined by flow-injection inductively coupled plasma mass spectrometry. The sample treatment, optimization of analytical variables and measurable concentration levels are discussed. The limits of quantification (10 sd_{n − 1}) calculated from a procedural blank sample solution were 4.0, 2.0, 1.5, 0.8 and 0.5 ng g⁻¹ for Au, Pt, Pd, Ir and Rh, respectively. The accuracy of the proposed method was tested by determining these elements in SARM 7 platinum-ore reference material. For all the analytes, the relative standard deviation of the combined dissolution, separation and determination methods was below 3.5% (n = 6).