Thermal properties of single walled carbon nanotube‐silicone nanocomposites

The effect of single walled carbon nanotube (SWCNT) fillers on the low temperature thermal properties and curing behavior of SWCNT‐silicone nanocomposite are reported for the first time. The SWCNT‐silicone composites were prepared by different mixing procedures and characterized by differential scanning calorimetry (DSC). Solution mix, with the aid of sonication and soaking achieved better dispersion of SWCNTs in the silicone. The adding of SWCNTs in polymer seriously hindered the curing of silicone elastomer. The hindrance increased with increasing concentration of SWCNT and the quality of dispersion. The glass transition temperatures (T_g) of the nanocomposites were found to be independent of the SWCNT addition, although, the steps in the heat capacity (Δc_p) of the glass transition were smaller with increasing SWCNTs concentration. The melt crystallization behavior was strongly dependent on the concentration and dispersion of SWCNT in the polymer. The cooling scan showed that the higher concentration and the better dispersion of SWCNTs in the silicone resulted in higher percentage of melt crystallization of this nanocomposite. The correlation of the change of thermal properties to the dispersion of CNT in polymer may be used to determine the quality of SWCNT dispersion in silicone polymer. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1845–1852, 2008     

Structure-dependent reactivity of semiconducting single-walled carbon nanotubes with benzenediazonium salts

The addition of diazonium salts to single-walled carbon nanotubes (SWCNTs) in aqueous surfactant suspensions quenches the intrinsic near-infrared fluorescence of semiconducting SWCNTs through sidewall chemical reactions. Spectrally resolved fluorescence spectroscopy of mixed SWCNT samples has been used to measure structure-dependent relative reactivities in the initial stages of these reactions. For several 4-substituted benzenediazonium salts, Ar-R (Ar = N 2 (+)-C 6H 4 and R = Cl, NO 2, OMe), reactivities at pH 10 were found to be greatest for SWCNTs having the largest band gaps. The magnitude of this band gap dependence varies according to the R-group of the salt, with R = OMe showing the strongest variation. For R = OH, acidification of the sample to pH 5.5 results in reversal of the structural trend, as smaller band gap SWCNTs show slightly greater reactivities. The derivatization reactions observed here proceed concurrently, although at different rates, for semiconducting and metallic SWCNT species. These results therefore provide insight into the difficulties of separating metallic and semiconducting SWCNTs through selective reaction schemes and underscore the need for fluorescence spectroscopy to be used in assessing semiconducting SWCNT reactions.     

Naphthalenebisimides as photofunctional surfactants for SWCNTs – towards water-soluble electron donor–acceptor hybrids

A water soluble naphthalenebisimide derivative (NBI) was synthesized and probed to individualize, suspend, and stabilize single wall carbon nanotubes (SWCNTs). Besides a comprehensive photophysical and electrochemical characterization of NBI, stable suspensions of SWCNTs were realized in buffered D₂O. Overall, the dispersion efficiency of the NBI surfactant was determined by comparison with naphthalene based references. Successful individualization of SWCNTs was corroborated in several microscopic assays. In addition, emission spectroscopy points to the strong quenching of SWCNT centered band gap emission, when NBIs are immobilized onto SWCNTs. The origin of the quenching was found to be strong electronic communication, which leads to charge separation between NBIs and photoexcited SWCNTs, and, which yields reduced NBIs as well oxidized SWCNTs. Notably, electrochemical considerations revealed that the energy content of these charge separated states is one of the highest reported for SWCNT based electron donor–acceptor hybrids so far.     

Sequence-specific self-stitching motif of short single-stranded DNA on a single-walled carbon nanotube

The DNA-single-walled carbon nanotube (SWCNT) hybrid molecule has attracted significant attention recently for its ability to disperse and sort SWCNTs according to their chirality. Key for utilizing their unique properties is an understanding of the structure of DNA adsorbed on the SWCNT surface, which we study here using molecular simulations. Using replica exchange molecular dynamics (REMD), we explore equilibrium structures formed by single strands of 12-mer oligonucleotides, of varying sequence, adsorbed on a (6,5)-SWCNT. We find a consistent motif in which the DNA strand forms a right-handed helical wrap around the SWCNT, stabilized by "stitches" (hydrogen bonding between distant bases) to itself. Variability among equilibrium populations of DNA self-stitched structures was observed and shown to be directly influenced by DNA sequence and composition. Competition between conformational entropy and hydrogen bonding between bases is predicted to be responsible for the formation of random versus stitched configurations.     

High NIR-purity index single-walled carbon nanotubes for electrochemical sensing in microfluidic chips

Single-walled carbon nanotubes (SWCNTs) should constitute an important natural step towards the improvement of the analytical performance of microfluidic electrochemical sensing. SWCNTs inherently offer lower detection potentials, higher surfaces and better stability than the existing carbon electrodes. However, pristine SWCNTs contain some carbonaceous and metallic impurities that influence their electrochemical performance. Thus, an appropriate processing method is important for obtaining high purity SWCNTs for analytical applications. In this work, a set of 0.1 mg mL(-1) SWCNT dispersions with different degrees of purity and different dispersants (SDBS; pluronic F68 and DMF) was carefully characterized by near infrared (NIR) spectroscopy giving a Purity Index (NIR-PI) ranging from 0.039 to 0.310. The highest purity was obtained when air oxidized SWCNTs were dispersed in SDBS, followed by centrifugation. The SWCNT dispersions were utilized to modify microfluidic chip electrodes for the electrochemical sensing of dopamine and catechol. In comparison with non-SWCNT-based electrodes, the sample with the highest NIR-PI (0.310) exhibited the best analytical performance in terms of improved sensitivity (3-folds higher), very good signal-to-noise ratio, high resistance-to-fouling in terms of relative standard deviation (RSD 7%; n = 15), and enhanced resolution (2-folds higher). In addition, very well-defined concentration dependence was also obtained with excellent correlation coefficients (r ≥ 0.990). Likewise, a good analytical sensitivity, suitable detection limits (LODs) and a very good precision with independence of the concentration assayed (RSDs ≤ 5%) was achieved. These valuable features indicate the suitability of this material for quantitative analysis. NIR-PI and further TEM and XRD characterization demonstrated that the analytical response was driven and controlled by the high NIR-PI of the SWCNTs used. The significance of this work is the demonstration for the first time of the sensitivity-purity relationship in SWCNT microfluidic chips. A novel and valuable analytical tool for electrochemical sensing has been developed: SWCNTs with high purity and a rich surface chemistry with functional groups, both essential for analytical purposes. Also, this work helps to better understand the analytical potency of SWCNTs coupled to microfluidic chips and it opens new gates for using these unique dispersions in real-world applications.     

Fluorimetric characterization of single-walled carbon nanotubes

Single-walled carbon nanotubes (SWCNTs) are a family of structurally related artificial nanomaterials with unusual properties and many potential applications. Most SWCNTs can emit spectrally narrow near-IR fluorescence at wavelengths that are characteristic of their precise diameter and chiral angle. Near-IR fluorimetry therefore offers a powerful approach for identifying the structural species present in SWCNT samples. Such characterization is increasingly important for nanotube production, study, separation, and applications. General-purpose and specialized instruments suitable for SWCNT fluorimetric analysis are described, and methods for interpreting fluorimetric data to deduce the presence and relative abundances of different SWCNT species are presented. Fluorescence methods are highly effective for detecting SWCNTs in challenging samples such as complex environmental or biological specimens because of the methods’ high sensitivity and selectivity and the near absence of interfering background emission at near-IR wavelengths. Current limitations and future prospects for fluorimetric characterization of SWCNTs are discussed.     

An unexpected new optimum in the structure space of DNA solubilizing single-walled carbon nanotubes

Here we report quantitative data on the amount of single-walled carbon nanotubes that can be suspended with oligodeoxynucleotides in aqueous buffer, together with rate constants for the thermal denaturation of the resulting DNA-nanotube complexes at elevated temperatures. Sequence motifs d(GT)n and d(AC)n with n=2, 3, 5, 10, 20, or 40 were employed, both individually and as equimolar mixtures of the complementary strands. Unexpectedly, the greatest suspending efficiency was found for the mixture of short, complementary oligonucleotides d(GT)3 and d(AC)3. Unlike the suspending efficiency, the kinetic stability of the nanotube suspensions increases with increasing chain length of the DNA, with half life times of >25 h at 90 degrees C for the complexes of the longest strands. Our results identify a new, unexpected optimum in DNA sequence space for suspending carbon nanotubes. They also demonstrate that suspending power depends on the presence of complementary strands. Exploratory assays suggest that nanotubes can be deposited site-selectively from suspensions formed with short DNA sequences.     

Diameter Selection of Carbon Nanotubes in Polymer/SWCNT Nanowire Arrays Fabricated by Template Wetting

Arrays of polymer/SWCNT (single‐wall carbon nanotube) nanowires supported on a residual nanocomposite film are prepared by melt wetting using porous anodic aluminum oxide (AAO) as a template. The aggregation parameter of SWCNTs extracted from the analysis of their Raman radial breathing modes gives the highest value for native SWCNTs, indicating that they tend to organize into bundles giving rise to a high degree of aggregation. However, the lowest value achieved at the interface between the nanocomposite film and the nanoarray is explained considering that the forces acting during infiltration are able to disrupt the SWCNT bundles inducing nanotube dispersion. In addition, scanning the nanoarrays along the nanowires length by Raman microscopy has shown a diameter selection of SWCNTs by the AAO membrane. The results reported in this work reveal that it is possible to fabricate arrays of nanowires with homogeneous SWCNT distribution along tens of microns, optimizing nanotube dispersion.     

Synthesis and characterization of polyethylene chains grafted onto the sidewalls of single‐walled carbon nanotubes via copolymerization

Polyethylene (PE) chains grafted onto the sidewalls of SWCNTs (SWCNT‐g‐PE) were successfully synthesized via ethylene copolymerization with functionalized single‐walled carbon nanotubes (f‐SWCNTs) catalyzed by rac‐(en)(THInd)₂ZrCl₂/MAO. Here f‐SWCNTs, in which α‐alkene groups were chemically linked on the sidewalls of SWCNTs, were synthesized by Prato reaction. The composition and microstructure of SWCNT‐g‐PE were characterized by means of ¹H NMR, Fourier transform infrared spectroscopy (FTIR), Raman spectroscopy, thermogravimetric analyses (TGA), field‐emission scanning electron microscope (FESEM), and transmission electron microscope (TEM). Nanosized cable‐like structure was formed in the SWCNT‐g‐PE, in which the PE formed a tubular shell and several SWCNTs bundles existed as core. The formation of the above morphology in the SWCNT‐g‐PE resulted from successfully grafting of PE chains onto the surface of SWCNTs via copolymerization. The grown PE chains grafted onto the sidewall of the f‐SWCNTs promoted the exfoliation of the mass nanotubes. Comparing with pure PE, the physical mixture of PE/f‐SWCNTs and in situ PE/SWCNTs mixture, thermal stability, and mechanical properties of SWCNT‐g‐PE were higher because of the chemical bonding between the f‐SWCNTs and PE chains. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 5459–5469, 2007     

Role of matrix crystallinity in carbon nanotube dispersion and electrical conductivity of iPP‐based nanocomposites

A homopolymer iPP and a series of propylene‐ethylene random copolymers with a content of ethylene from 7 to 21 mol % were used as matrices to prepare single‐walled carbon nanotube (SWCNT) nanocomposites in a range of SWCNT concentration from 0.15 to 1 wt %. The solution blending and melt‐ compression molding procedures were kept identical for all nanocomposites. The poly(propylenes) have crystallinities ranging from 70 to 10%, and serve to test the role of SWCNTs acting as nucleants to preserve in the nanocomposites the uniform dispersion of SWCNTs after sonication. The major role of polymer crystallinity is to mediate toward a more open and more connected SWCNT network structure. Fast nucleation and growth of high crystalline matrices on multiple sites along the surface of the nanotubes prevents SWCNT clustering, and entraps the SWCNT network between the semicrystalline structure reducing the driving force of nanotubes to curl and twist. Depletion of crystallites in the less crystalline matrices (<35% crystallinity) leads to curled and poorly connected nanotubes. A consequence of the gradual loss of SWCNT connectivity is a decreased electrical conductivity; however, the change with crystallinity is not linear. Conductivity decreases sharply with decreasing crystallinity for SWCNT contents near the percolation region, while for contents approaching the plateau region the electrical conductivity is less sensitive to matrix crystallinity. The percolation threshold decreases rapidly for polymers with <～30% crystallinity and slowly levels off at crystallinities >～40%. At SWCNT concentrations of 0.15 wt %, SEM images of nanocomposites with the highest crystallinity matrix indicate debundled and interconnected nanotubes, whereas more disconnected and curled SWCNTs remain in the lowest crystallinity nanocomposites. Electrical conductivity in the former is relatively high, whereas the latter are insulators. Also discussed is the nucleating effect of nanotubes and restrictions of the filler to polymer chain diffusion in the crystallization of the polymers. SEM images and Raman spectra in the radial breathing modes region (100–400 cm^?1) are complementary tools to extract the quality and details of the SWCNT dispersion in the nanocomposites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 2084–2096, 2010     

Photoinduced charge separation in three-layer supramolecular nanohybrids: fullerene-porphyrin-SWCNT

Photoinduced charge separation processes of three-layer supramolecular hybrids, fullerene-porphyrin-SWCNT, which are constructed from semiconducting (7,6)- and (6,5)-enriched SWCNTs and self-assembled via π-π interacting long alkyl chain substituted porphyrins (tetrakis(4-dodecyloxyphenyl)porphyrins; abbreviated as MP(alkyl)(4)) (M = Zn and H(2)), to which imidazole functionalized fullerene[60] (C(60)Im) is coordinated, have been investigated in organic solvents. The intermolecular alkyl-π and π-π interactions between the MP(alkyl)(4) and SWCNTs, in addition, coordination between C(60)Im and Zn ion in the porphyrin cavity are visualized using DFT calculations at the B3LYP/3-21G(*) level, predicting donor-acceptor interactions between them in the ground and excited states. The donor-acceptor nanohybrids thus formed are characterized by TEM imaging, steady-state absorption and fluorescence spectra. The time-resolved fluorescence studies of MP(alkyl)(4) in two-layered nanohybrids (MP(alkyl)(4)/SWCNT) revealed efficient quenching of the singlet excited states of MP(alkyl)(4) ((1)MP*(alkyl)(4)) with the rate constants of charge separation (k(CS)) in the range of (1-9) × 10(9) s(-1). A nanosecond transient absorption technique confirmed the electron transfer products, MP˙(+)(alkyl)(4)/SWCNT˙(-) and/or MP˙(-)(alkyl)(4)/SWCNT˙(+) for the two-layer nanohybrids. Upon further coordination of C(60)Im to ZnP, acceleration of charge separation via(1)ZnP* in C(60)Im→ZnP(alkyl)(4)/SWCNT is observed to form C(60)˙(-)Im→ZnP˙(+)(alkyl)(4)/SWCNT and C(60)˙(-)Im→ZnP(alkyl)(4)/SWCNT˙(+) charge separated states as supported by the transient absorption spectra. These characteristic absorptions decay with rate constants due to charge recombination (k(CR)) in the range of (6-10) × 10(6) s(-1), corresponding to the lifetimes of the radical ion-pairs of 100-170 ns. The electron transfer in the nanohybrids has further been utilized for light-to-electricity conversion by the construction of proof-of-concept photoelectrochemical solar cells.     

Dispersions of individual single-walled carbon nanotubes of high length

In summary, we have presented a suitable approach to obtain surfactant-stabilized suspensions of long, individually dispersed SWCNTs essentially free of bundles. The combination of mild tip and bath ultrasonication has proven effective in unbundling the SWCNT ropes and, at the same time, in minimizing tube shortening. This method is expected to be useful for applications that critically depend on the availability of bulk dispersions of long, individual tubes with minimized defect densities, such as for nanotube-based electronics and composite materials. Furthermore, the observed purification-induced changes in the electronic structure of HiPco SWCNTs indicate that care has to be taken when comparing their properties with those of the as-produced material.     

Theoretical Evidence for the Stronger Ability of Thymine to Disperse SWCNT than Cytosine and Adenine: self-stacking of DNA bases vs their cross-stacking with SWCNT

Self-stacking of four DNA bases, adenine (A), cytosine (C), guanine (G) and thymine (T), and their cross-stacking with (5,5) as well as (10,0) single walled carbon nanotubes (SWCNTs) were extensively investigated with a novel hybrid DFT method, MPWB1K/cc-pVDZ. The binding energies were further corrected with MP2/6-311++G(d,p) method in both gas phase and aqueous solution, where the solvent effects were included with conductor-like polarized continuum model (CPCM) model and UAHF radii. The strongest self-stacking of G and A takes displaced anti-parallel configuration, but un-displaced or "eclipsed" anti-parallel configuration is the most stable for C and T. In gas phase the self-stacking of nucleobases decreases in the sequence G>A>C>T, while because of quite different solvent effects their self-stacking in aqueous solution exhibits a distinct sequence A>G>T>C. For a given base, cross-stacking is stronger than self-stacking in both gas phase and aqueous solution. Binding energy for cross-stacking in gas phase varies as G>A>T>C for both (10,0) and (5,5) SWCNTs, and the binding of four nucleobases to (10,0) is slightly stronger than to (5,5) SWCNT by a range of 0.1-0.5 kcal/mol. The cross-stacking in aqueous solution varies differently from that gas phase: A>G>T>C for (10,0) SWCNT and G>A>T>C for (5,5) SWCNT. It is suggested that the ability of nucleobases to disperse SWCNT depends on relative strength [Formula: see text] of self-stacking and cross-stacking with SWCNT in aqueous solution. Of the four investigated nucleobases thymine (T) exhibits the highest [Formula: see text] which can well explain the experimental finding that T more efficiently functionalizes SWCNT than C and A.     

Capacitive and Charge Transfer Effects of Single-Walled Carbon Nanotubes in TiO2 Electrodes

The transfer of nanoscale properties from single-walled carbon nanotubes (SWCNTs) to macroscopic systems is a topic of intense research. In particular, inorganic composites of SWCNTs and metal oxide semiconductors are being investigated for applications in electronics, energy devices, photocatalysis, and electroanalysis. In this work, a commercial SWCNT material is separated into fractions containing different conformations. The liquid fractions show clear variations in their optical absorbance spectra, indicating differences in the metallic/semiconducting character and the diameter of the SWCNTs. Also, changes in the surface chemistry and the electrical resistance are evidenced in SWCNT solid films. The starting SWCNT sample and the fractions as well are used to prepare hybrid electrodes with titanium dioxide (SWCNT/TiO₂). Raman spectroscopy reflects the optoelectronic properties of SWCNTs in the SWCNT/TiO₂ electrodes, while the electrochemical behavior is studied by cyclic voltammetry. A selective development of charge transfer characteristics and double-layer behavior is achieved through the suitable choice of SWCNT fractions.     

Substituted carborane-appended water-soluble single-wall carbon nanotubes: new approach to boron neutron capture therapy drug delivery

Substituted C(2)B(10) carborane cages have been successfully attached to the side walls of single-wall carbon nanotubes (SWCNTs) via nitrene cycloaddition. The decapitations of these C(2)B(10) carborane cages, with the appended SWCNTs intact, were accomplished by the reaction with sodium hydroxide in refluxing ethanol. During base reflux, the three-membered ring formed by the nitrene and SWCNT was opened to produce water-soluble SWCNTs in which the side walls are functionalized by both substituted nido-C(2)B(9) carborane units and ethoxide moieties. All new compounds are characterized by EA, SEM, TEM, UV, NMR, and IR spectra and chemical analyses. Selected tissue distribution studies on one of these nanotubes, {([Na(+)][1-Me-2-((CH(2))(4)NH-)-1,2-C(2)B(9)H(10)][OEt])(n)(SWCNT)} (Va), show that the boron atoms are concentrated more in tumors cells than in blood and other organs, making it an attractive nanovehicle for the delivery of boron to tumor cells for an effective boron neutron capture therapy in the treatment of cancer.     

Polymer-assisted dispersion of single-walled carbon nanotubes in alcohols and applicability toward carbon nanotube/sol-gel composite formation

Single-walled carbon nanotubes (SWCNTs) were directly dispersed into various alcohols by sonicating the nanotubes in the presence of poly(4-vinylpyridine) (P4VP). Depending upon the alcohol, it was possible to disperse up to 0.3 g of SWCNTs per liter of alcohol using only 0.6 g of P4VP, and with solution stability greater than 6 weeks. Scanning electron microscopy of "bucky" paper prepared from the polymer-treated nanotubes revealed reduced bundle size compared to the corresponding untreated nanotube paper. Additionally, the applicability of the dispersion system in the formation of SWCNT/silica composites is demonstrated.     

Residual Metal Impurity Aids Facile In Situ Electrochemical Surface Derivatization of Single‐Walled Carbon Nanotubes

Residual metal impurities were exploited as reactants in the functionalization of the surface of single‐walled carbon nanotubes (SWCNT) with nickel hexacyanoferrate (NiHCF) by simple electrochemical cycling in ferricyanide solutions. This facile in situ electrochemical modification process provides intimate contact between NiHCF and SWCNTs that improves the stability of the redox property and reactivity of NiHCF. The characteristic redox behavior of NiHCF on SWCNT surfaces can be used as an electrochemical probe to access qualitative and quantitative information on unknown electroactive metal impurities in SWCNTs. Significantly, the NiHCF‐modified SWCNTs exhibit pseudocapacitive behavior, and the calculated specific capacitances are 710 and 36 F g^?1 for NiHCF‐SWCNTs and SWCNTs respectively. Furthermore, NiHCF‐SWCNTs were transformed into Ni(OH)₂/SWCNTs and used for enzymeless glucose oxidation.     

Direct measurement of the interactions of amide solvents with single-walled carbon nanotubes using isothermal titration calorimetry

The interaction enthalpy of amide solvents with single-walled carbon nanotube (SWCNT) dispersions is measured using isothermal titration calorimetry (ITC). N,N-Dimethyl-formamide (DMF) and N-methyl-2-pyrilidone (NMP) were used to make dispersions of highly purified (6,5) SWCNTs. Using isothermal titration calorimetry, the ΔH and K(A) terms related to the solvent-nanotube interactions were measured, and ΔG and ΔS of the interaction were determined. It was found that the interaction enthalpy of NMP with SWCNTs dispersed in DMF was exothermic. The addition of a second solvent into a NMP or DMF dispersion produced spontaneous exfoliation of SWCNT bundles as the solvent properties became more favorable. During the titration, a positive change in interaction entropy within the dispersed system due to the unbundling of SWCNTs was measured. From blank titrations of pure DMF into pure NMP and the reverse, dilution enthalpies were also calculated and compared to the literature, along with the corresponding enthalpic interaction coefficients, h(xx) and h(xxx). From our results, ITC appears to be a viable technique for measuring the interaction of solvent molecules with the surface of SWCNTs and for measuring the effect of mixed solvent properties on SWCNT dispersions.     

Application of poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] for splitting of single-walled carbon nanotube bundles in polystyrene/SWCNT composite

Dispersions of single-walled carbon nanotubes (SWCNTs) in organic solutions containing poly[2-methoxy-5-(2-ethylhexyloxy)-1,4-phenylenevinylene] (MEH-PPV) were studied by Raman spectroscopy, UV-vis-NIR spectroscopy, and electron microscopy. This polymer interacts with the nanotube resulting in the appearance of a new red-shifted absorption band in the electronic spectrum. This indicates the formation of a charge-transfer complex between MEH-PPV and SWCNTs. Additives of MEH-PPV make it possible to achieve stable suspensions of nanotubes in styrene. A polystyrene/SWCNT/MEH-PPV composite with a high degree of bundle splitting was obtained by polymerization. It was shown that the luminescence intensity of the nanotubes in the Raman spectrum can serve as a indicator for the estimation of the degree of splitting of SWCNT bundles in the composite.     

一维碳纳米管/二维二硫化钼混合维度异质结的原位制备及其电荷转移性能

一维(1D)材料与二维(2D)材料的结合可形成独特的混合维度异质结,其在继承2D/2D范德瓦尔斯异质结的独特物性之外,还具有丰富的堆叠构型,为进一步调控异质结的结构及性能提供了新的可操控自由度。p型1D单壁碳纳米管(SWCNT)与n型2D二硫化钼(MoS₂)的结合,为调控异质结的能带结构及器件性能提供了丰富的选择。本文直接在高密度、手性窄分布的SWCNT定向阵列及无序薄膜表面原位生长MoS₂,制备出高质量1D SWCNT/2D MoS₂混合维度异质结。深入分析形核点的表面形貌与结构,提出了“吸附-扩散-吸附”生长机制,用于解释混合维度异质结的生长。利用拉曼光谱分析,证实SWCNT与MoS₂间存在显著的电荷转移作用,载流子可在界面处快速传输,为后续基于此类1D/2D异质结的新型电子及光电器件的设计与制备提供了新思路。