Synthesis of Ag Nanoparticle Doped MnO2/GO Nanocomposites at a Gas/Liquid Interface and its Application in H2O2 Detection

Ag/MnO₂/GO nanocomposites were synthesized via the method of gas/liquid interface based on silver mirror reaction, and a non‐enzymatic H₂O₂ sensor was fabricated through immobilizing Ag/MnO₂/GO nanocomposites on GCE. The composition and morphology of the nanocomposites were studied by energy‐dispersive X‐ray spectroscopy (EDS), X‐ray diffraction (XRD), X‐ray photoelectron spectroscopy (XPS) and transmission electron microscopy (TEM). Electrochemical investigation indicated that it exhibited a favorable performance for the H₂O₂ detection. Its linear detection range was from 3 μM to 7 mM with a correlation coefficient of 0.9960; the sensitivity was 105.40 μA mM^?1 cm^?2 and the detection limit was estimated to be 0.7 μM at a signal‐to‐noise ratio of 3.     

Preparation of Co3O4/graphene Oxide Composites by a Depositing‐decompostion Method and its Application for Electrochemical Determination of Glucose

Co₃O₄/graphene oxide (GO) nanocomposites were successfully prepared by a depositing‐decomposition method. The as‐prepared samples were characterized by scanning electron microscopy (SEM) and Raman spectroscopy. Cyclic voltammetry (CV) was used to evaluate the electrochemical response of a glass carbon electrode (GCE) modified with Co₃O₄/GO nanocomposite towards glucose. Compared with the Co₃O₄/GCE, the Co₃O₄/GO/GCE exihibits higher electrocatalytic activity due to the synergistic effects of electrocatalytic ability of Co₃O₄ and large surface of GO. The Co₃O₄/GO/GCE was applied for glucose detection in alkaline solution. The linear current response range of glucose on Co₃O₄/GO/GCE covered the range from 9 × 10^?5 to 6.03 × 10^?3 M, with a detection limit of 5.2 × 10^?7 M (S/N = 3).     

Design of a Sensitive Electrochemical Sensor Based on Ferrocene-reduced Graphene Oxide/Mn-spinel for Hydrazine Detection

Herein, we report construction of a ferrocene-reduced graphene oxide-Mn spinel modified glassy carbon electrode (Fc−G/Mn₃O₄/GCE) as a sensitive electrochemical probe for hydrazine detection via its oxidation. The synergistic effect of ferrocene, graphene oxide and Mn₃O₄ provides it a great electrocatalytic effect. The electrochemical investigations of Fc−G/Mn₃O₄/GCE were studied using cyclic voltammetry, while differential pulse voltammetry was utilized for recording the electrocatalytic sensing of hydrazine. The prepared Fc−G/Mn₃O₄ offers a platform for sensitive and selective detection of low-level hydrazine in two linear ranges from 0.045 to 108 μM and 108 to 653 μM with limit of detection 8.5 nM. Real sample analysis was also performed in local industrial water samples with satisfactory recovery results.     

Detection of Dexamethasone Sodium Phosphate in Blood Plasma: Application of Hematite in Electrochemical Sensors

We studied sensor application of a graphene oxide and hematite (α‐Fe₂O₃/GO) composite electrode well‐characterized by the SEM and XRD. Through differential pulse voltammetry (DPV), oxidation of dexamethasone sodium phosphate (DSP) was studied at the surface of a glassy carbon electrode (GCE) modified with graphene oxide nanosheets (GO) and the α‐Fe₂O₃/GO composite. The values of the transfer coefficient (α) and the diffusion coefficient (D) of DSP were 0.5961 and 4.71×10^?5 cm² s^?1 respectively. In the linear range of 0.1–50 μM, the detection limit (DL) was 0.076 μM. In the second step, a GCE was modified with α‐Fe₂O₃/GO composite and the DSP measurement step was repeated to analyzed and compare the effects of hematite nanoparticles present on graphene oxide surfaces. According to the results, α and D were 0.52 and 2.406×10^?4 cm² s^?1 respectively and the DL was 0.046 μM in the linear range of 0.1–10.0 μM. The sensor is simple, inexpensive and uses blood serum.     

Facile Synthesis of Graphene/Cobalt Oxide Nanohexagons for the Selective Detection of Dopamine

This work presents a simple green approach for the chemical synthesis of cobalt oxide nano hexagons (Co₃O₄ NHs) with an average size of 160±40 nm incorporated graphene nanosheets (GR). The techniques used to confirm the formation of GR−Co₃O₄ NHs are transmission electron microscopy (TEM), energy‐dispersive X‐ray spectroscopy (EDX), and X‐ray diffraction spectroscopy (XRD). The dopamine (DA) sensor was fabricated by drop casting GR−Co₃O₄ NHs on the pre‐cleaned glassy carbon electrode (GCE). GR−Co₃O₄ modified GCE displayed a sensitive and selective electrochemical determination of DA compared to only GR and Co₃O₄ NHs modified GCE. Our fabricated sensor showed a wide linear range from 0.2 to 3443 μM with low limit of detection (84 nM) towards the determination of DA. The sensitivity of our fabricated sensor was calculated to be 108 μA mM⁻¹ cm⁻². As well, a significant storage stability, repeatability and reproducibility were attained by GR−Co₃O₄ NHs modified GCE. Human urine samples were targeted for the demonstration of practicality of our sensor.     

Direct electrochemistry of hemoglobin on graphene/Fe3O4 nanocomposite-modified glass carbon electrode and its sensitive detection for hydrogen peroxide

Graphene/Fe₃O₄ nanocomposite was prepared for the immobilization of hemoglobin (Hb) to improve the electron transfer between Hb and glass carbon electrode (GCE). The characterization of nanocomposites was described by transmission electron microscopy, Fourier transform infrared, Raman spectroscopy, and X-ray photoelectron spectroscopy, respectively. The electrochemistry of Hb on the graphene/Fe₃O₄-based GCE was investigated by cyclic voltammetry and amperometric measurement. The modified electrode showed a wide linear range from 0.25 μmol/L to 1.7 mmol/L with a correlation coefficient of 0.9967. The detection limit of the H₂O₂ biosensor was estimated at 6.0?×?10^?6?mol/L at a signal-to-noise ratio of 3.     

Preparation of non‐covalent Metalloporphyrin/C60 Composite and its Electrocatalysis to Hydrogen Peroxide

Three non‐covalent metallotetraphenylporphyrin/fullerene (MTPPS₄ (M=Zn²⁺, Fe²⁺, Co²⁺)/C₆₀) nanocomposites were prepared by π‐π molecular interaction and characterized by scanning electron microscopy and UV‐Vis absorption spectroscopy. Electrocatalytic studies indicated that the MTPPS₄/C₆₀ nanocomposites which were embedded in TOAB film on the glassy carbon electrode (GCE) (TOAB/MTPPS₄/C₆₀/GCE) exhibited a high electrocatalytic activity for H₂O₂. MTPPS₄ enhanced the electrocatalytic ability of C₆₀ in the increasing order of TOAB/ZnTPPS₄/C₆₀/GCE, TOAB/FeTPPS₄/C₆₀/GCE and TOAB/CoTPPS₄/C₆₀/GCE. The measurement with the differential pulse voltammetry (DPV) exhibited that there is a well‐defined linear relationship between the reduction currents and H₂O₂ concentrations in the range from 0.3 to 1.0 mM, with the detection limit of 0.07 mM at the TOAB/ZnTPPS₄/C₆₀/GCE electrode, of 0.08 mM at the TOAB/FeTPPS₄/C₆₀/GCE electrode, of 0.04 mM at the TOAB/CoTPPS₄/C₆₀/GCE electrode, respectively. The biosensors showed a good anti‐interfering ability towards glucose, ascorbic acid and L‐cysteine and a high potential practicality.     

Nafion covered core–shell structured Fe3O4@graphene nanospheres modified electrode for highly selective detection of dopamine

Nafion covered core–shell structured Fe₃O₄@graphene nanospheres (GNs) modified glassy carbon electrode (GCE) was successfully prepared and used for selective detection dopamine. Firstly, the characterizations of hydro-thermal synthesized Fe₃O₄@GNs were investigated by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and Raman spectroscopy. Then Fe₃O₄@GNs/Nafion modified electrode exhibited excellent electrocatalytic activity toward the oxidations of dopamine (DA). The interference test showed that the coexisted ascorbic acid (AA) and uric acid (UA) had no electrochemical interference toward DA. Under the optimum conditions, the broad linear relationship was obtained in the experimental concentration from 0.020 μM to 130.0 μM with the detection limit (S/N = 3) of 0.007 μM. Furthermore, the core–shell structured Fe₃O₄@GNs/Nafion/GCE was applied to the determination of DA in real samples and satisfactory results were got, which could provide a promising platform to develop excellent biosensor for detecting DA.     

Novel Nonenzymatic Hydrogen Peroxide Sensor Based on Ag/Cu2O Nanocomposites

The nanocomposites of Ag nanoparticles supported on Cu₂O were prepared and used for fabricating a novel nonenzymatic H₂O₂ sensor. The morphology and composition of the nanocomposites were characterized using the scanning electron microscope (SEM), transmission electron microscope (TEM), energy‐dispersive X‐ray spectrum (EDX) and X‐ray diffraction spectrum (XRD). The electrochemical investigations indicate that the sensor possesses an excellent performance toward H₂O₂. The linear range is estimated to be from 2.0 μM to 13.0 mM with a sensitivity of 88.9 μA mM^?1 cm^?2, a response time of 3 s and a low detection limit of 0.7 μM at a signal‐to‐noise ratio of 3. Additionally, the sensor exhibits good anti‐interference.     

Ag nanoparticles decorated Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>/chitosan nanocomposite: synthesis,characterization and application toward electrochemical sensing of hydrogen peroxide

We studied a rapid, sensitive and selective amperometric sensor for determination of hydrogen peroxide by electrodeposited Ag NPs on a modified glassy carbon electrode (GCE). The modified GCE was constructed through a step by step modification of magnetic chitosan functional composite (Fe₃O₄–CH) and high-dispersed silver nanoparticles on the surface. The resulted Ag@Fe₃O₄–CH was characterized by various analytical methods including Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, scanning electron microscopy and cyclic voltammetry. The proposed sensor employed Ag@Fe₃O₄–CH/GCE as the working electrode with a linear current response to the hydrogen peroxide concentration in a wide range from 0.01 to 400 µM with a low limit of detection (LOD = 0.0038 µM, S/N = 3). The proposed sensor showed superior reproductivity, sensitivity and selectivity for the detection of hydrogen peroxide in environmental and clinical samples.     

Synthesis of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>—Ag nanocomposites and their application to enzymeless hydrogen peroxide detection

To achieve highly sensitive nonenzymatic detection of H₂O₂, a novel electrochemical sensor based on Fe₃O₄-Ag nanocomposites was developed. Nanocomposites were synthesized by reducing [Ag(NH₃)₂]⁺ at the gas/liquid interface in the presence of silver seeds and confirmed by transmission electron microscopy and X-ray diffractometry. Electrochemical investigations indicate that the sensor is able to detect H₂O₂ within a wide linear range of 0.5 μM to 4.0 mM, sensitivity of 135.4 μA mM^?1 cm^?2 and low detection limit of 0.2 μM (S/N = 3). Additionally, the sensor exhibits good anti-interference ability, stability and repeatability. These results show that the Fe₃O₄-Ag nanocomposite is a promising electrocatalytic material for sensors construction.     

A highly stable nano γ-Fe2O3/gold-film modified electrode for electrochemically sensitive sensing to hydrazine

The magnetic γ-Fe₂O₃ material was prepared in a new way and characterized by transmission electron microscopy and X-ray diffraction. It was modified on a glass carbon electrode (GCE) coated with gold film to form nano γ-Fe₂O₃/Au/GCE. The electrooxidation of hydrazine has been deeply explored with the resulting electrode in 0.1 M phosphate-buffered saline (pH 7.0). The affecting factors containing pH of supporting electrolyte, scan rate, deposition time, amount of γ-Fe₂O₃, and possible interferences were investigated, and the oxidation mechanisms of hydrazine on the γ-Fe₂O₃/Au/GCE were also explored. The amperometric response to hydrazine is linear in the range of 0.02 to 11 μM, and the detection limit is 6 nM at a SNR of 3. The prepared sensor exhibited good sensitivity, stability, and lower detection limit for the determination of hydrazine injection.     

Bismuth Tellurate Nanospheres and Electrochemical Behaviors of L-Cysteine at the Nanospheres Modified Electrode

Bismuth tellurate nanospheres have been successfully synthesized by a facile hydrothermal route. X-ray diffraction (XRD) shows that the nanospheres are composed of orthorhombic Bi₂Te₂O₇ phase. Scanning electron microscopy (SEM) displays that the diameter of the nanospheres is 100–500 nm. The bismuth tellurate nanospheres (BTS) modified glassy carbon electrode (GCE) has been prepared for the electrochemical detection of L-cysteine (L-CySH). A pair of semi-reversible CV peaks at +0.14 V and–0.84 V, respectively are observed. The BTS modified GCE displays high electrocatalytic activity toward L-CySH and exhibits a linear relationship in the range of 0.0001–2 mM with a detection limit of 0.046 μM in KCl solution. The broad linear range, low detection limit, good reproducibility and stability make the BTS modified GCE valuable for the practical application.     

A novel nonenzymatic biosensor for evaluation of oxidative stress based on nanocomposites of graphene blended with CuI

A high-sensitive nonenzymatic hydrogen peroxide (H₂O₂) biosensor based on cuprous iodide and graphene (CuI/Gr) composites has been explored for the detection of H₂O₂ released by living cells and monitoring the oxidative stress of cells under excellular stimulation. The biosensor properties were evaluated by cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), amperometric i-t curve, and the redox-competition mode of scanning electrochemical microscopy (SECM). Our observations demonstrate that the CuI/Gr nanocomposites modified glassy carbon electrode (GCE) exhibits excellent catalytic activity for H₂O₂ with relatively low detection limit and a wide linear range from 0.5 μM to 3 mM. Moreover, the redox-competition mode of SECM imaging study further illustrates the improved electrochemical catalytic capability for H₂O₂ reduction with CuI/Gr nanocomposites deposited on graphite electrode. Hence, the as-prepared nonenzymatic H₂O₂ biosensor could be used to detect H₂O₂ release from different kinds of living cells under stimulation while eliminating the interference of ascorbic acid.     

Fe3O4 Nanorods-RGO-ionic Liquid Nanocomposite Based Electrochemical Sensor for Aflatoxin B1 in Ground Paprika

A novel and sensitive method for the determination of aflatoxin B1 (AFA−B1) in ground paprika using a methyltrioctylammonium chloride ionic liquid (IL), iron oxide nanorods (Fe₃O₄ nanorods) and reduced graphene oxide (RGO) fabricated glassy carbon electrode (GCE) was developed. The synthesized nanoparticles, nanocomposites and modified electrode surfaces were characterized by Fourier transform infrared spectroscopy (FTIR), transmission electron microscopy (TEM), thermogravimetric analysis (TGA/DSC) and x-ray diffraction (XRD) analyses. Moreover, the electrochemical performance of the developed sensor was determined by cyclic voltammetry (CV) and differential pulse voltammetry (DPV). The obtained results demonstrate that the sensitivity of AFA−B1 is significantly enhanced on RGO-Fe₃O₄ nanorods-IL-GCE in comparison with bare GCE, RGO-GCE and RGO-Fe₃O₄ nanorods-GCE. The redox peak currents of AFA−B1 exhibited good linear relationship with its concentration in the range from 0.02 to 0.33 ng mL⁻¹ with detection limit of (LOD) 0.03 ng mL⁻¹ and limit of quantification (LOQ) 0.36 ng mL⁻¹ respectively (S/N=3). In addition, the fabricated electrode showed good stability and reproducibility. The proposed technique was effectively applied to identify the AFA−B1 in real ground paprika samples with acceptable results.     

Fabrication of Photoelectrochemical Glucose Biosensor in Flow Injection Analysis System Using ZnS/CdS‐Carbon Nanotube Nanocomposite Electrode

In this work, a photoamperometric glucose biosensor based on glucose oxidase (GODx) was developed in flow injection analysis (FIA) system using ZnS‐CdS quantum dot (QD) modified multiwalled carbon nanotube/glassy carbon electrode (ZnS‐CdS/MWCNT/GCE). Cyclic voltammograms of the proposed electrode (GODx/ZnS‐CdS/MWCNT/GCE) showed a pair of well‐defined reversible redox peak attributing that direct electron transfer between the protein and electrode. The current of the reduction peak became more cathodic in the presence of O₂ due to the electrocatalytic activity of the electrode towards the reduction of dissolved O₂, but reduction current shifted to a less negative value upon addition of glucose in the solution. The obtained CV currents were affected by the irradiation of the electrode surface. Thus, the photoelectrochemical biosensing of glucose in the FIA system was studied by monitoring of the changes in the electrocatalyzed reduction peak current of dissolved O₂ at the proposed electrode dependent on glucose concentration. The proposed photoelectrochemical FIA method has a linear response to glucose ranging from of 0.01 to 1.0 mM with detection limit of 3.0 μM under optimized conditions. Photoelectrochemical biosensor was successfully fabricated in FIA system for selective, sensitive and repeatable detection of glucose and has been satisfactorily applied to determination of glucose in real sample.     

A Non‐Enzymatic Hydrogen Peroxide Sensor Based on Ag/MnOOH Nanocomposites

A novel non‐enzymatic sensor based on Ag/MnOOH nanocomposites was developed for the detection of hydrogen peroxide (H₂O₂). The H₂O₂ sensor was fabricated by immobilizing Ag/MnOOH nanocomposites on a glassy carbon electrode (GCE). The morphology and composition of the sensor surface were characterized using scanning electron microscopy, energy‐dispersive X‐ray spectroscopy, transmission electron microscopy and X‐ray diffraction spectroscopy. The electrochemical investigation of the sensor indicates that it possesses an excellent electrocatalytic property for H₂O₂, and could detect H₂O₂ in a linear range from 5.0 µM to 12.8 mM with a detection limit of 1.5 µM at a signal‐to‐noise ratio of 3, a response time of 2 s and a sensitivity of 32.57 µA mM^?1 cm^?2. Additionally, the sensor exhibits good anti‐interference. The good analytical performance, low cost and straightforward preparation method made this novel electrode material promising for the development of effective non‐enzymatic H₂O₂ sensor.     

7,7,8,8-tetracyanoquinodimethane microsheets for hydrogen peroxide reduction

In this Letter, we demonstrate for the first time that 7,7,8,8-tetracyanoquinodimethane microsheets (TCNQMSs) can effectively catalyze the reduction of H₂O₂ because TCNQ is a strong electron acceptor, TCNQMSs modified glass carbon electrode (GCE) is prepared by a simple casting method. This H₂O₂ sensor shows a fast amperometric response time of less than 3 s, and the corresponding linear range is estimated to be from 3 to 238 mM (r = 0.992) and a detection limit of 4.76 μM at a signal-to-noise ratio of 3. Our present study is important because it provides us a new structure for H₂O₂ detection application.     

A Novel Biomimetic Hydrogen Peroxide Biosensor Based on Pt Flowers‐decorated Fe3O4/Graphene Nanocomposite

A sensitive and selective amperometric H₂O₂ biosensor was obtained by utilizing the electrodeposition of Pt flowers on iron oxide‐reduced graphene oxide (Fe₃O₄/rGO) nanocomposite modified glassy carbon electrode (GCE). The morphology of Fe₃O₄/rGO and Pt/Fe₃O₄/rGO was characterized by transmission electron microscopy (TEM) and scanning electron microscopy (SEM), respectively. The step‐wise modification and the electrochemical characteristics of the resulting biosensor were characterized by cyclic voltammetry (CV) and chronoamperometry methods. Thanks to the fast electron transfer at the Pt/Fe₃O₄/rGO electrode interface, the developed biosensor exhibits a fast and linear amperometric response upon H₂O₂. The linear range of Pt/Fe₃O₄/rGO is 0.1∼2.4 mM (R²=0.998), with a sensitivity of 6.875 μA/mM and a detection limit of 1.58 μM (S/N=3). In addition, the prepared biosensor also provides good anti‐interferent ability and long‐term stability due to the favorable biocompatibility of the electrode interface. The proposed sensor will become a reliable and effective tool for monitoring and sensing the H₂O₂ in complicate environment.     

An in-situ synthesis of novel V2O5/G-C3N4/PVA nanocomposite for enhanced electrocatalytic activity toward sensitive and selective sensing of folic acid in natural samples

This paper describes a highly sensitive and selective electrochemical sensing of folic acid (FA) using vanadium pentoxide decorated graphene carbon nitride covalently grafted polyvinyl alcohol modified GC electrode (V₂O₅/G-C₃N₄/PVA/GCE). The V₂O₅/G-C₃N₄/PVA nanocomposite was synthesized by an in-situ oxidative polymerization method and characterized by various techniques such as UV–visible, Raman, FE-SEM, XRD, FT-IR, EDX, HR-TEM, SAED, and electrochemical methods. The V₂O₅/G-C₃N₄/PVA nanocomposite modified GCE showed superior electrocatalytic activity towards the FA detection. The superior electrochemical activity of the catalyst is owing to good conductivity, high surface area and enhanced electron transfer efficiency of the nanocomposite. The amperometric (i-t) studies revealed that the V₂O₅/G-C₃N₄/PVA nanocomposite modified GCE performed well by attaining a linear response of FA from 0.01 to 60 µM with a lower detection limit 0.00174 µM and the sensitivity of 19.02 μA µM⁻¹ cm⁻². Meanwhile, the V₂O₅/G-C₃N₄/PVA nanocomposite modified GCE exhibited good selectivity, rapid and stable response towards FA. The proposed method has been successfully applied for the selective determination of FA in various real samples such as apple juice, green tea and tap water with samples with good recoveries.