Aerosol-assisted fabrication of mesoporous titania spheres with crystallized anatase structures and investigation of their photocatalitic properties

We demonstrate practical aerosol-assisted approach to synthesize spherical mesoporous titania particles with high surface areas. Scanning electron microscopy observation of the spray-dried products clearly shows spherical morphology. To remove surfactants and enhance crystallinity, the spray-dried products are calcined under various temperatures. The crystalline structures inside the particles are carefully detected by wide-angle XRD measurements. With increase of the calcination temperatures, anatase crystal growth proceeds and transformation from anatase to rutile is occurred. The effect of various calcination temperatures on the mesostructures is also studied by using N₂ adsorption desorption isotherms. The mesoporous titania particles calcined at 350, 400, and 500 °C exhibit type IV isotherms with a capillary condensation step and shows a hysteresis loop, which is a characteristic of mesoporous materials. The reduction in the surface areas and the pore volumes is confirmed by increasing the calcination temperatures, while the average pore diameters are increased gradually. This is attributed to the distortion of the mesostructures due to the grain growth of the anatase phase and the transformation to the rutile phase during the calcination process. As a preliminary experimental photocatalytic activity, oxidative decomposition of acetaldehyde under UV irradiation is examined. The mesoporous titania calcined at 400 °C shows the highest photocatalytic activity, due to both high surface area and well-developed anatase crystalline phase.     

焙烧的P-25 TiO2微结构特性和光催化活性

光催化氧化能把有机污染物完全转化为二氧化碳和水,被认是有广泛应用前景的水处理方法[1,2]．但是,这一方法真正在污水处理中实际应用,有许多问题仍待解决,其中光催化剂的活性和稳定性需要进一步改善．研究最多的光催化剂是TiO2,影响其催化活性的因素很多[3,4],本工作用XRD、TEM、BET研究了烧结的P－25TiO2微结构特征,并用苯酚光催化降解作探针反应,得到了很有意义的相关信息．1材料和方法1．1催化剂商品P－25TiO2是从Degussa公司购买．样品分别经不同温度和时间焙烧,具体条件见表1．1．2催化剂表征XRD用于测定样品品相…     

Characterization and evaluation of the photocatalytic properties of wormhole-like mesoporous silica incorporating TiO2, prepared using different hydrothermal and calcination temperatures

TiO₂?CSiO₂ mesoporous materials were synthesised by deposition of TiO₂ nanoparticles prepared by the sol?Cgel method on to the internal pore surface of wormhole-like mesoporous silica. In this work we synthesised wormhole-like mesoporous silica of different surface area by changing the hydrothermal temperature (70, 100, or 130?°C). Subsequent to this, titania solution was deposited on to the inner surface of the pores and this was followed by calcination at different temperatures (400, 600, or 800?°C). The effect of different hydrothermal and calcination temperature on the photocatalytic properties was evaluated. The samples were characterized by N₂-sorption, X-ray diffraction, X-ray photoelectron spectroscopy, field emission scanning electron microscopy, and transmission electron microscopy. The effect of different hydrothermal and calcination temperatures on the photocatalytic properties was evaluated by measuring the degradation of methylene blue in aqueous solution under UV light irradiation (mercury lamp, 125?W). The results indicated that appropriate surface area and degree of crystallinity are two important factors for obtaining high photocatalytic efficiency. Samples prepared at a hydrothermal temperature of 100?°C and calcined at 800?°C had the best photocatalytic performance, because of the highest surface area and high crystallinity.     

Calcination temperature-dependent morphology of photocatalytic ZnO nanoparticles prepared by an electrochemical–thermal method

ZnO nanoparticles (NPs) with tunable morphologies were synthesized by a hybrid electrochemical–thermal method at different calcination temperatures without the use of any surfactant or template. The NPs were characterized by Fourier transform infrared (FT-IR) spectroscopy, X-ray diffraction, dynamic light scattering, thermogravimetry–differential thermal analysis, scanning electron microscope and N₂ gas adsorption–desorption studies. The FT-IR spectra of ZnO NPs showed a band at 450 cm^?1, a characteristic of ZnO, which remained fairly unchanged at calcination temperatures even above 300 °C, indicating complete conversion of the precursor to ZnO. The products were thermally stable above 300 °C. The ZnO NPs were present in a hexagonal wurtzite phase and the crystallinity of ZnO increased with an increasing calcination temperature. The ZnO NPs calcined at lower temperature were mesoporous in nature. The surface areas of ZnO NPs calcined at 300 and 400 °C were 51.10 and 40.60 m² g^?1, respectively, which are significantly larger than commercial ZnO nanopowder. Surface diffusion has been found to be the key mechanism of sintering during heating from 300 to 700 °C with the activation energy of sintering as 8.33 kJ mol^?1. The photocatalytic activity of ZnO NPs calcined at different temperatures evaluated by photocatalytic degradation of methylene blue under sunlight showed strong dependence on the surface area of ZnO NPs. The ZnO NPs with high surface area showed enhanced photocatalytic activity.     

Preparation and characterization of highly photoactive nanocrystalline TiO<Subscript>2</Subscript> powders by solvent evaporationinduced crystallization method

Highly photoactive bi-phase nanocrystalline TiO₂ photocatalyst was prepared by a solvent evaporation-induced crystallization (SEIC) method, and calcined at different temperatures. The obtained TiO₂ photocatalyst was characterized with X-ray diffraction (XRD), transmission electron microscopy (TEM) and BET surface areas. The photocatalytic activity was evaluated by the photocatalytic oxidation of acetone in air. The results show that solvent evaporation can promote the crystallization and phase transformation of TiO₂ at 100°C. When calcination temperatures are below 600°C, the prepared TiO₂ powders show bimodal pore size distributions in the mesoporous region. At 700°C, the pore size distributions exhibit monomodal distribution of the inter-aggregated pores due to the collapse of the intra-aggregated pores. At 100°C, the obtained TiO₂ photocatalyst by this method shows good photocatalytic activity, and at 400°C, its photocatalytic activity exceeds that of Degussa P25. This may be attributed to the fact that the prepared TiO₂ photocatalyst has higher specific surface areas, smaller crystallite size and bimodal pore size distribution.     

Effects of crystallinity, {001}/{101} ratio,and Au decoration on the photocatalytic activity of anatase TiO2 crystals

Anatase TiO₂ nanocrystals and sub-microcrystals with truncated octahedral bipyramidal morphologies were prepared by direct calcination of TiOF₂ precursors. The as-prepared TiO₂ samples were thoroughly characterized by X-ray diffraction, Raman spectroscopy, field-emission scanning electron microscopy, N₂ adsorption-desorption isotherms, X-ray photoelectron spectroscopy, and UV-visible diffuse spectroscopy. It was found that the crystallinity, grain size, and {001}/{101} ratio of the samples can be increased by raising the calcination temperature from 500 to 800 °C. The higher crystallinity and {001}/{101} facet ratio resulted in an increase in both aqueous and gas-phase photocatalytic activities, by inhibiting the recombination and separation of electrons and holes. After selecting two TiO₂ samples with high crystallinity and {001}/{101} ratio, Au nanoparticles were decorated on their surfaces, and the photocatalytic activity of the resulting samples under visible light illumination was studied. It was found that the visible light-induced photocatalytic activity increased by 2.6 and 4.8 times, respectively, upon Au decoration of the samples prepared by calcination of TiOF₂ at 700 and 800 °C.     

Synthesis of TiO2 (B) and High‐temperature Stable Anatase TiO2 Nanowires by Hydrothermal Method and Investigation of Photocatalytic Activity

In this study, TiO₂ nanowires (TNWs) were synthesized through hydrothermal method and were characterized using X‐Ray diffraction (XRD), transmission electron microscopy (TEM) and BET techniques. Monoclinic TiO₂ (B) is the dominant phase of TNWs up to 600°C which is completely transformed into a highly crystalline anatase phase at 800°C. The photocatalytic activity of TNWs, prepared at various calcination temperatures, was investigated in the removal of Rhodamine B as an organic model pollutant. The results indicated that the photocatalytic activity of TNWs, prepared at 800°C calcination temperature, was better than that of other samples and even TiO₂–P25 nanoparticles.     

稀土Ce掺杂对ZnO结构和光催化性能的影响

采用共沉淀-焙烧法合成了一系列不同含量的稀土Ce掺杂的ZnO光催化剂. 利用傅里叶变换红外(FT-IR)光谱、粉末X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见(UV-Vis)光谱、光致发光(PL)谱等技术对所制备的光催化剂进行了系列表征. 以酸性橙II脱色降解为模型反应, 考察了掺杂不同含量的铈及不同焙烧温度对ZnO的物理结构和光催化脱色性能的影响. 结果表明: 掺入质量分数(w)为2%的铈可以明显改善氧化锌表面状态, 有利于产生更多的表面羟基; 同时可以抑制光生电子与光生空穴(e^-/h⁺)的复合, 显著提高光催化脱色活性和光催化稳定性; 焙烧温度对光催化剂的晶体结构、表面性能和光催化活性产生较大影响, 500 °C的焙烧处理使样品的结晶度较高, 同时催化剂颗粒粒径较细, 表面具有丰富的羟基. 但过高的焙烧温度(600-800 °C)将导致催化剂的物理结构发生恶化, 降低光催化性能.     

稀土Ce掺杂对ZnO结构和光催化性能的影响

采用共沉淀-焙烧法合成了一系列不同含量的稀土Ce掺杂的ZnO光催化剂. 利用傅里叶变换红外(FT-IR)光谱、粉末X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见(UV-Vis)光谱、光致发光(PL)谱等技术对所制备的光催化剂进行了系列表征. 以酸性橙II脱色降解为模型反应, 考察了掺杂不同含量的铈及不同焙烧温度对ZnO的物理结构和光催化脱色性能的影响. 结果表明: 掺入质量分数(w)为2%的铈可以明显改善氧化锌表面状态, 有利于产生更多的表面羟基; 同时可以抑制光生电子与光生空穴(e^-/h⁺)的复合, 显著提高光催化脱色活性和光催化稳定性; 焙烧温度对光催化剂的晶体结构、表面性能和光催化活性产生较大影响, 500 °C的焙烧处理使样品的结晶度较高, 同时催化剂颗粒粒径较细, 表面具有丰富的羟基. 但过高的焙烧温度(600-800 °C)将导致催化剂的物理结构发生恶化, 降低光催化性能.     

High temperature stability and photocatalytic activity of nanocrystalline anatase powders with Zr and Si co-dopants

TiO₂ nanopowders doped by Si and Zr were prepared by sol–gel method. The effects of Si and Zr doping on the structural, optical, and photo-catalytic properties of titania nanopowders have been studied by X-ray diffraction (XRD), scanning electron microscopy, transmission electron microscopy, and UV–Vis absorption spectroscopy. XRD results suggest that adding impurities has a significant effect on anatase phase stability, crystallinity, and particle size of TiO₂. Titania rutile phase formation in ternary system (Ti–Si–Zr) was inhibited by Zr⁴⁺ and Si⁴⁺ co-doped TiO₂ in high temperatures (500–900 °C) and 36 mol% anatase composition is retained even after calcination at 1,000 °C. The photocatalyst activity was evaluated by photocatalytic degradation kinetics of aqueous methylen orange under visible radiation. The results show that the photocatalytic activity of the 20 %Si and 15 %Zr co-doped TiO₂ nanopowders have a larger degradation efficiency than pure TiO₂ under visible light.     

Effects of doping with CeO2 and calcination temperature on physicochemical properties of the NiO/Al2O3 system

The effects of doping with CeO₂ and calcination temperature on the physicochemical properties of the NiO/Al₂O₃ system have been investigated using DTA, XRD, nitrogen adsorption measurements at −196°C and decomposition of H₂O₂ at 30–50°C. The pure and variously doped solids were subjected to heat treatment at 300, 400, 700, 900 and 1000°C. The results revealed that the specific surface areas increased with increasing calcination temperature from 300 to 400°C and with doping of the system with CeO₂. The pure and variously doped solids calcined at 300 and 400°C consisted of poorly crystalline NiO dispersed on γ-Al₂O₃. Heating at 700°C resulted in formation of well crystalline NiO and γ-Al₂O₃ phases beside CeO₂ for the doped solids. Crystalline NiAl₂O₄ phase was formed starting from 900°C. The degree of crystallinity of NiAl₂O₄ increased with increasing the calcination temperature from 900 to 1000°C. An opposite effect was observed upon doping with CeO₂. The NiO/Al₂O₃ system calcined at 300 and 400°C has catalytic activity higher than individual NiO obtained at the same calcination temperatures. The catalytic activity of NiO/Al₂O₃ system increased, progressively, with increasing the amount of CeO₂ dopant and decreased with increasing the calcination temperature.     

Chicken Bone as a Bioresource for the Bioceramic (Hydroxyapatite)

Natural hydroxyapatite (HAP) is isolated from waste chicken bone by thermal calcinations at different temperatures in the range of 200 °C to 1000 °C. The isolated HAP has been characterized using thermo gravimetric analysis (TG) and differential thermal analysis (DTA), Fourier Transformed Infrared spectroscopy (FTIR), X-ray diffraction (XRD), field emission electron microscope (FE-SEM), and energy dispersive X-ray (EDX). The XRD results showed that the enhanced crystallinity of HAP phase by thermal calcination above 600 °C and the crystal size has been found to increase with increasing temperature of thermal calcinations due to agglomeration. Value addition for the waste chicken bone is given by the isolation of useful bioceramics (HAP) and the optimum temperature for the thermal calcination is found to be 600 °C. The isolated HAP has been characterized as carbonated HAP of B type with the hexagonal structure. These results will not only make the chicken bone as an important bioresource for the HAP but will also reduce the environmental pollution caused by dumping of the waste chicken bone.     

Photocatalytic Activity of Nanosized ZnWO4 Prepared by the Sol-gel Method

Nanosized ZnWO4 photocatalysts were successfully synthesized via the sol-gel process in a temperature range of 450-800 ℃.The grain size,crystal size,and crystallinity of ZnWO4 particles increased with the increase of calcination temperature and prolonging calcination time.The photocatalytic activity was measured for the degradation of an aqueous Rhodamine-B(RhB)solution and gaseous formaldehyde(FAD).With the increase of calcination temperature and time,the activities increased to a maximum and then decreased.ZnWO4 photocatalyst prepared at 550 ℃ for 10 h showed the highest activity,which is similar to the photocatalytic activity of P25TiO2 for the degradation of gaseous FAD.High crystallinity,large surface area,and good dispersion are responsible for the high photocatalytic performance of the prepared ZnWO4.     

Effect of temperature on high pressure cellulose compression

The effect of temperature during cellulose compression has been studied using mechanical testing, particle size analysis, density and pressure–volume–temperature (PVT) measurements, crystallinity index, scanning electron microscope photographs and water sorption isotherms. Commercial cellulose powder samples with different crystallinity levels were compacted at high pressure (177 MPa) for 10 min at two different temperatures: 25 and 160 °C. Three point bending test results for compressed samples are discussed. When pressure was applied directly to powders at room temperature, the cellulose sample with the highest level of crystallinity showed an increase in its crystallinity index of about 5 %, while this was about 22 % for the sample with the lowest level. These increases were even higher at 160 °C attaining 8 and 33 % respectively. Using density measurements, a densification phase related to this crystallinization was observed, and the PVT diagrams from different cellulose samples showed that this was associated with high temperatures. Water sorption isotherms were made on cellulose samples before and after compression. They showed a diminution of cellulose sorption capacity after compression at 160 °C, revealing the effect of temperature on high-pressure cellulose compression, reducing specific surface area. Events of this nature suggest a sintering mechanism, when temperature is associated with high pressure during cellulose compression.     

Effect of Calcination Temperature on the Structure and Catalytic Properties of MnO<Subscript><Emphasis Type="Italic">x</Emphasis></Subscript>/Ca<Subscript>2</Subscript>O<Subscript>3</Subscript> in the Reaction of CO and Ethane Oxidation

Effect of the calcination temperature of the MnOx/Ga2O3 system on its structural and catalytic properties in the reaction of oxidation of CO and hydrocarbons. The dependences of the catalytic activity of MnO _x /Ga₂O₃ in the reactions of CO and ethane oxidation on the calcination temperature exhibit an extremal behavior. The maximum values of activity are observed upon calcination of the system at 700°C, i.e., at the temperature that is limiting for the existence of a solid solution of manganese ions in γ-Ga₂O₃. The structural changes occurring with increasing calcination temperature are accompanied by a substantial decrease in the specific surface area of a sample. The observed rise in the specific catalytic activity (by a factor of ~7 upon an increase in the preliminary-calcination temperature from 600 to 800°C) confirms that the thermal activation effect exists for the given system.     

Large‐Scale Production of Hierarchical TiO2 Nanorod Spheres for Photocatalytic Elimination of Contaminants and Killing Bacteria

We report a facile non‐hydrothermal method for the large‐scale production of hierarchical TiO₂ nanorod spheres for the photocatalytic elimination of contaminants and killing bacteria. Crescent Ti/RF spheres were prepared by deliberately adding titanium trichloride (TiCl₃) to the reaction of resorcinol (R) and formaldehyde (F) in an open reactor under heating and stirring. The hierarchical TiO₂ nanorod spheres were obtained by calcining the crescent Ti/RF spheres in a furnace in air to burn off the RF spheres. This method has many merits, such as large‐scale production, good crystallisation of TiO₂, and good reproducibility, all of which are difficult to realise by conventional hydrothermal methods. The calcination temperature plays a significant role in influencing the morphology, crystallisation, porosity, Brunauer–Emmett–Teller (BET) specific surface area, and hierarchy of the TiO₂ nanorod spheres, thus resulting in different photocatalytic performances under UV light and solar light irradiation. The experimental results have demonstrated that the hierarchical TiO₂ nanorod spheres obtained after calcination of the crescent Ti/RF spheres at different temperatures displayed similar photocatalytic activities under irradiation with UV light. We attribute this to a balance of opposing effects of the investigated factors. A higher calcination temperature leads to greater light absorption capability of the TiO₂ nanorod spheres, thus resulting in higher photocatalytic antibacterial activity under solar light irradiation. It is also interesting to note that the hierarchical TiO₂ nanorod spheres displayed intrinsic antibacterial activity in the absence of light irradiation, apparently because their sharp outward spikes can easily pierce and penetrate the walls of bacteria. In this study, the sharpest hierarchical TiO₂ nanorod spheres were obtained after calcination at 500 °C, and these exhibited the highest antibacterial activity without light irradiation. A higher calcination temperature proved detrimental to the sharpness of the TiO₂ nanorods, thus reducing their intrinsic antibacterial activity.     

Fabrication and photocatalytic activity of LaFeO3 ribbon-like nanofibers

LaFeO₃ ribbon-like nanofibers were synthesized via a sol–gel-assisted electrospinning method. The differences in morphology and photocatalytic property of LaFeO₃ nanofibers prepared through different needles were investigated. At the same time, the morphology and photocatalytic activity of porous LaFeO₃ nanobelts formed at different calcination temperatures were also investigated. Scanning electron microscopy results revealed that the obtained ribbon-like LaFeO₃ nanofibers made using a coaxial needle contained a large number of pores. Moreover, with the increase of calcination temperature, the morphology of the fibers also changed. X-ray diffraction analysis showed a series of fibers all in orthorhombic LaFeO₃ phase but no other impurities. In addition, the photocatalytic activity of LaFeO₃ nanofibers was studied for the degradation of methylene blue under visible light. The results demonstrated that ribbon-like nanofibers exhibited excellent photocatalytic activity compared with the others and the LaFeO₃ nanobelts calcined at 500°C had the best photocatalytic activity. Based on the experimental results, possible forming mechanisms involving in LaFeO₃ nanofibers through different needles are also discussed.     

Photocatalytic degradation of metoprolol in water suspension of TiO<Subscript>2</Subscript> nanopowders prepared using sol–gel route

Nanocrystalline titanium dioxide (TiO₂) powders have been synthesized by sol–gel method using titanium tetrachloride (TiCl₄) or tetrabutyl titanate (Ti(OC₄H₉)₄ as precursors, different alcohols and calcination temperatures in the range from 400 to 650 °C. The photocatalytic activity of as-prepared powders has been tested for the degradation of metoprolol tartrate salt, a selective β-blocker used to treat a variety of cardiovascular diseases, and compared to photocatalytic activity obtained from Degussa P25. Nanosized TiO₂ powders prepared from TiCl₄ and amyl-alcohol, calcined at 550 °C, displayed an activity comparable to Degussa P25, whereas the sample from the same series, calcined at 650 °C, showed higher photocatalytic activity in the whole range of the catalyst loading. Structural, morphological and surface properties of synthesized TiO₂ nanopowders have been investigated by XRD, SEM, EDS and BET measurements, as well as FTIR and Raman spectroscopy, in order to find out the material properties which enable rapid an efficient decomposition of metoprolol under UV radiation.     

Physical properties of nano-titania hollow fibers and their photocatalytic activity in the decomposition of phenol

A series of nano-titania (TiO₂) photocatalytic materials with a hollow fiber structure were successfully prepared using tetra-n-butyl titanate (Ti(OC₄H₉)₄) as precursor and cotton fiber as the template. Scanning electron microscopy (SEM), X-ray diffraction (XRD), and N₂ adsorption-desorption measurements were employed to characterize the morphology, crystal structure, and surface structure of the samples. The photocatalytic activities of the samples were studied by phenol photodegradation in water under UV irradiation. The effect of calcination temperature, photocatalyst dosage, initial concentration of phenol and irradiation time on the photodegradation of phenol was studied. Results showed that the TiO₂ fiber materials have hollow structures, indicating that these materials had a large specific surface area. The fiber structure material showed better photocatalytic properties for the degradation of phenol than pure TiO₂ under UV light, and the sample calcined at 500°C exhibited the highest phenol photodegradation efficiency. In addition, the possibility of cyclic usage of the photocatalyst was also confirmed, the photocatalytic activity of TiO₂ fiber remained ca. 90% of photocatalytic activity of the fresh sample after being used four times. Moreover, TiO₂ fiber was easily recovered by centrifugal separation from water.     

沉淀煅烧法合成(CuAg)0.15In0.3Zn1.4S2光催化剂及可见光下的制氢性能

研究了沉淀煅烧法制备的纳米级(CuAg)_0.15In_0.3Zn_1.4S₂光催化剂以及产氢效率,并采用X射线衍射、透射电镜、扫描电镜、N₂吸附-脱附、紫外-可见吸收光谱等手段对催化剂进行了表征. 结果表明,(CuAg)_0.15In_0.3Zn_1.4S₂的结晶度、比表面积和吸收可见光能力与煅烧温度和煅烧时间有关. 在可见光下,以KI为电子给体,考察了不同条件对光催化产氢能力的影响. 发现在600℃煅烧5h时所制的(CuAg)_0.15In_0.3Zn_1.4S₂光催化剂产氢活性最高,产氢速率为1750 μmol g^-1 h^-1,量子效率在420±5nm达到12.8%,比未煅烧催化剂的光催化活性提高了约6倍.