Vibrational spectroscopic and electrochemical characteristics of poly (propylene glycol)-silver triflate polymer electrolyte system

Fourier transform infrared spectroscopic and electrochemical complex impedance studies have been carried out on a series of complexes containing poly(propylene glycol) of molecular weight 4,000 and silver triflate (AgCF₃SO₃) salt corresponding to the ether oxygen to metal cation ratios (O : M) in the range 16:1 to 12:1. The formation of ion pairs and aggregates noticed in the case of specimens having high salt concentrations as well as the complete coordination of the cation with the ether oxygen at low salt concentrations within the PPG4000-AgCF₃SO₃ polymer electrolyte system have been confirmed. The appearance of two weak triflate bands at 1,032 and 1,272 cm⁻¹ in the absorption spectra in respect of low salt concentrations is indicative of the fact that triflate ions are free within the polymer matrix. The room temperature (298 K) electrical conductivity is found to increase with increasing ether oxygen content while exhibiting the maximum value of 7.1 × 10⁻⁵ Scm⁻¹ possibly due to silver ionic transport in the case of the typical composition having an O : M ratio of 16:1.     

Combined effect of CuO nanofillers and DBP plasticizer on ionic conductivity enhancement in the solid polymer electrolyte PEO–LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>

We report a new kind of polyethylene oxide, PEO–LiCF₃SO₃-based composite polymer electrolyte, containing active copper oxide (CuO) nanoparticles with dibutyl phthalate (DBP) prepared by solution-cast technique. The incorporation of 10 wt.% DBP and 5 wt.% CuO to the salted polymer showed a significant conductivity enhancement with maximum conductivity 2.62 × 10⁻⁴ Scm⁻¹ at room temperature. This could be attributed to the increasing of amorphous phase content and structural changes in the polymer electrolyte. Arrhenius plot suggest that temperature-dependent conductivity is a thermally activated process.     

Impedance and FTIR studies on plasticized PMMA–LiN(CF<Subscript>3</Subscript>SO<Subscript>2</Subscript>)<Subscript>2</Subscript> nanocomposite polymer electrolytes

Plasticized polymer electrolytes composed of poly(methyl methacrylate) (PMMA) as the host polymer and lithium bis(trifluoromethanesulfonyl)imide LiN(CF₃SO₂)₂ as a salt were prepared by solution casting technique at different ratios. The ionic conductivity varied slightly and exhibited a maximum value of 3.65 × 10⁻⁵ S cm⁻¹ at 85% PMMA and 15% LiN(CF₃SO₂)₂. The complexation effect of salt was investigated using FTIR. It showed some simple overlapping and shift in peaks between PMMA and LiN(CF₃SO₂)₂ salt in the polymer electrolyte. Ethylene carbonate (EC) and propylene carbonate (PC) were added to the PMMA–LiN(CF₃SO₂)₂ polymer electrolyte as plasticizer to enhance the conductivity. The highest conductivities obtained were 1.28 × 10⁻⁴ S cm⁻¹ and 2.00 × 10⁻⁴ S cm⁻¹ for EC and PC mixture system, respectively. In addition, to improve the handling of films, 1% to 5% fumed silica was added to the PMMA–LiN(CF₃SO₂)₂–EC–PC solid polymer electrolyte which showed a maximum value at 6.11 × 10⁻⁵ S cm⁻¹ for 2% SiO₂.     

A comparative study of lithium and sodium salts in PAN-based ion conducting polymer electrolytes

The conducting polymer electrolyte films consisting of polyacrylonitrile (PAN) as the host polymer, lithium triflate (LiCF₃SO₃) and sodium triflate (NaCF₃SO₃) as inorganic salts were prepared by the solution-cast technique. The pure PAN film was prepared as a reference. The ionic conductivity for the films is characterized using impedance spectroscopy. The room temperature conductivity for the PAN + 26 wt.% LiCF₃SO₃ film and the PAN + 24 wt.% NaCF₃SO₃ film is 3.04 × 10⁻⁴ S cm⁻¹ and 7.13 × 10⁻⁴ S cm⁻¹, respectively. XRD studies show that the complexation that has occurred in the PAN containing salt films and complexes formed are amorphous. The FTIR spectra results confirmed the complexation has taken place between the salt and the polymer. These results correspond with surface morphology images obtained from SEM analysis. The conductivity–temperature dependence of the highest conducting film from PAN + LiCF₃SO₃ and PAN + NaCF₃SO₃ systems follows Arrhenius equation in the temperature range of 303 to 353 K. The PAN containing 24 wt.% LiCF₃SO₃ film has a higher ionic conductivity and lower activation energy compared to the PAN containing 26 wt.%LiCF₃SO₃ film. These results can be explained based on the Lewis acidity of the alkali ions, i.e., the interaction between Li⁺ ion and the nitrogen atom of PAN is stronger than that of Na⁺ ion.     

Investigation on structural characteristics of PVDF–AgCF<Subscript>3</Subscript>SO<Subscript>3</Subscript>–Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanocomposite solid polymer electrolyte system

There has been an increasing interest towards the incorporation of nanosize ceramic fillers in polymer electrolytes. Solid polymer electrolytes based on polyvinylidene fluoride (PVDF), silver triflate (AgCF₃SO₃), and x wt% of aluminum oxide (Al₂O₃) nanopowders (where x = 1, 3, 5, and 10, respectively) have been prepared using solution casting technique. The structural characteristics of these thin film specimens were studied using Fourier transform infrared (FTIR) and X-ray diffraction (XRD) patterns at room temperature. The appearance of new absorption bands and gradual shifts observed in some characteristic peaks confirmed the complex formation between polyvinylidene fluoride and silver triflate. Furthermore, the addition of nanosized filler Al₂O₃ has also indicated the interaction of the filler with the polymer salt complex. The XRD patterns obtained for all these samples in the 2θ range 10° to 70° showed the amorphous nature of these samples. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006.     

Structural investigation on PEO-based polymer electrolytes dispersed with Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanoparticles

Thin solid polymer electrolytes based on polyethylene oxide (PEO) and silver triflate (AgCF₃SO₃) dispersed with various concentrations of aluminum oxide (Al₂O₃) nanoparticles have been prepared by solution casting technique. These thin polymer films are found to have thickness of the order of 30 to 100 μm. The X-ray diffraction (XRD) patterns have indicated the amorphous nature of the polymer electrolyte. The differential scanning calorimeter (DSC) traces showed slight change in the glass transition temperature (T _g) whereas the degree of crystallization (X _c) decreases markedly due to the addition of alumina nanoparticles. Fourier transform infrared (FTIR) spectral analysis of all these samples has revealed the presence of absorption bands around 1,000 cm⁻¹; thus indicating the complexation of silver ions with oxygen in PEO. Employing the Wagner’s polarization technique as the standard method, the total ionic transference number for the complexed polymer electrolyte was found to be approximately unity thereby revealing that the significant contribution to electrical conduction was due to ions only. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, December 7–9, 2006     

Ionic conduction behavior in PVC–PEG blend polymer electrolytes upon the addition of TiO2

The blend-based polymer electrolyte consisting of poly (vinyl chloride) (PVC) and poly (ethylene glycol) (PEG) as host polymers and lithium perchlorate (LiClO₄) as the complexing salt was studied. An attempt was made to investigate the effect of TiO₂ concentration in the unplasticized PVC–PEG polymer electrolyte system. The XRD and FTIR studies confirm the formation of a polymer–salt complex. The conductivity results indicate that the incorporation of ceramic filler up to a certain concentration (15 wt.%) increases the ionic conductivity and upon further addition the conductivity decreases. The maximum ionic conductivity 0.012 × 10⁻⁴ S cm⁻¹ is obtained for PVC–PEG–LiClO₄–TiO₂ (75–25–5–15) system. Thermal stability of the polymer electrolyte is ascertained from TG/DTA studies.     

Effect of ZnO nanoparticles filler concentration on the properties of PEO-ENR50-LiCF<Subscript>3</Subscript>SO<Subscript>3</Subscript> solid polymeric electrolyte

A solid polymer electrolyte comprising blend of poly(ethylene oxide) and 50% epoxidized natural rubber (ENR50) as a polymer host, LiCF₃SO₃ as a salt and nanoparticle ZnO as an inorganic filler was prepared by solution-casting technique. The effect of filler on the electrolyte properties was characterized and analysed. FESEM analysis showed that the filler was well distributed in the polymer matrix, while the effective interaction between the salt and the polymer host was reduced by the addition of filler. As evidenced by FTIR analysis, which showed the formation of triplet peak at C-O-C stretching region. Ionic conductivity was found to decrease from 1.4 × 10⁻⁴ Scm⁻¹ to 2.5 × 10⁻⁶ Scm⁻¹ upon the addition of filler, due to the blocking effect of filler into the electrolyte conduction pathways. The temperature dependence on the electrolyte conductivity obeys Arrhenius rule in two temperature regions.     

Investigation of dibutyl phthalate as plasticizer on poly(methyl methacrylate)–lithium tetraborate based polymer electrolytes

Polymer electrolyte membranes, comprising of poly(methyl methacrylate) (PMMA), lithium tetraborate (Li₂B₄O₇) as salt and dibutyl phthalate (DBP) as plasticizer were prepared using a solution casting method. The incorporation of DBP enhanced the ionic conductivity of the polymer electrolyte. The polymer electrolyte containing 70 wt.% of poly(methyl methacrylate)–lithium tetraborate and 30 wt.% of DBP presents the highest ionic conductivity of 1.58 × 10⁻⁷ S/cm. The temperature dependence of ionic conductivity study showed that these polymer electrolytes obey Vogel–Tamman–Fulcher (VTF) type behaviour. Thermogravimetric analysis (TGA) was employed to analyse the thermal stability of the polymer electrolytes. Fourier transform infrared (FTIR) studies confirmed the complexation between poly(methyl methacrylate), lithium tetraborate and DBP.     

Effect of ethylene carbonate plasticizer and TiO<Subscript>2</Subscript> nanoparticles on 49% poly(methyl methacrylate) grafted natural rubber-based polymer electrolyte

The effect of plasticizer and TiO₂ nanoparticles on the conductivity, chemical interaction and surface morphology of polymer electrolyte of MG49–EC–LiClO₄–TiO₂ has been investigated. The electrolyte films were successfully prepared by solution casting technique. The ceramic filler, TiO₂, was synthesized in situ by sol-gel process and was added into the MG49–EC–LiClO₄ electrolyte system. Alternating current electrochemical impedance spectroscopy was employed to investigate the ionic conductivity of the electrolyte films at 25 °C, and the analysis showed that the addition of TiO₂ filler and ethylene carbonate (EC) plasticizer has increased the ionic conductivity of the electrolyte up to its optimum level. The highest conductivity of 1.1 × 10⁻³ Scm⁻¹ was obtained at 30 wt.% of EC. Fourier transform infrared spectroscopy measurement was employed to study the interactions between lithium ions and oxygen atoms that occurred at carbonyl (C=O) and ether (C-O-C) groups. The scanning electron microscopy micrograph shows that the electrolyte with 30 wt.% EC posses the smoothest surface for which the highest conductivity was obtained.     

Solid polymer electrolytes based on squaric acid structure

Poly(squarate)s (PPS-1 and PPS-2) were synthesized by the reaction of squaryl dichloride with hydroquinone for PPS-1 and with 2,5-diethoxy-1,4-bis(trimethylsilyloxy)benzene for PPS-2, and the ionic conductivities, thermal properties, and electrochemical and thermal properties of their polymer electrolytes with LiN(CF₃SO₂)₂ were investigated. The ionic conductivity increased with increasing the lithium salt concentration for the PPS-1–LiN(CF₃SO₂)₂ electrolyte, and the highest ionic conductivities of 8.60 × 10⁻⁵ S/cm at 100 °C and 9.57 × 10⁻⁸ S/cm at 30 °C were found at the [Li] to [O] ratio of 2:1. And also, the ionic conductivity for the PPS-1–LiN(CF₃SO₂)₂ electrolyte increased with an increase in the lithium salt concentration, reached a maximum value at the [Li] to [O] ratio of 1:2, and then decreased. The highest ionic conductivity was to be 1.04 × 10⁻⁵ S/cm at 100 °C and 1.71 × 10⁻⁸ S/cm at 30 °C, respectively. Both polymer electrolytes exhibited relatively better electrochemical and thermal stabilities. Addition of the PPS-1 as a plasticizer into the poly(ethylene oxide) (PEO)–LiN(CF₃SO₂)₂ electrolyte system suppressed the crystallization of PEO, and improved the ionic conductivity at room temperature. Invited paper dedicated to Professor W. Weppner on his 65th birthday.     

Grafted natural rubber-based polymer electrolytes: ATR-FTIR and conductivity studies

Attenuated total reflectance–Fourier transformed infrared spectroscopy measurement is employed to study the interactions between the components of 30% methyl-grafted natural rubber (MG30), lithium trifluromethanesulfonate (LiCF₃SO₃ or LiTF), and propylene carbonate (PC). Vibrational spectra data of LiTF reveals that the ν_s(SO₃) at 1,045 cm⁻¹, δ_s(CF₃) at 777 cm⁻¹, and C=O stretching mode at 1,728 cm⁻¹ for MG30 have shifted to lower wave numbers in MG30–LiTF complexes indicating that complexation has occurred between MG30 and LiTF. The solvation of lithium ion is manifested in Li⁺ ← O=C interaction as shown by the downshifting and upshifting of C=O mode at 1,788 to 1,775 cm⁻¹ and ν_as(SO₃) at 1,250 to 1258 cm⁻¹, respectively, in LiTF–PC electrolytes. There is no experimental evidence of the interaction between MG30 and PC. Competition between MG30 and PC on associating with lithium ion is studied, and the studies show that the interaction between MG30–LiTF is stronger than that of the PC–LiTF in plasticized polymer–salt complexes. The effect of PC on the ionic conductivity of the MG30–LiTF system is explained in terms of the polymer, plasticizer, and salt interactions. The temperature dependence of conductivity of the polymer films obeys the Vogel–Tamman–Fulcher relation. Values of conductivity and activation energy of the MG30-based polymer electrolyte systems are presented and discussed.     

Conductivity, dielectric behaviour and thermal stability studies of lithium ion dissociation in poly(methyl methacrylate)-based gel polymer electrolytes

Thin films of poly(methyl methacrylate) (PMMA) with lithium triflate (LiCF₃SO₃) were prepared by using the solution-casting method with PMMA as the host polymer. Ionic conductivity and dielectric measurements were carried out on these films. The highest conductivity for polymer electrolyte with a ratio of 65:35 was found to be 9.88 × 10⁻⁵ S cm⁻¹, which is suitable for the production of mobile phone battery. Thermal gravimetric analysis was carried out to evaluate the thermal stability of the polymer electrolyte. The addition of salts will increase thermal stability of the polymer electrolyte.     

AC Conductivity,XRD and transport properties of melt quenched PbI<Subscript>2</Subscript>–Ag<Subscript>2</Subscript>O–Cr<Subscript>2</Subscript>O<Subscript>3</Subscript> system

Composite materials used for electrode and electrolyte materials have been intensely studied in view of their advantages such as higher conductivity and better operational performance compared to their single-phase counterparts. The present work aims at studying the electrical and structural characteristics of a new composite electrolyte namely, (PbI₂) _x  − (Ag₂O–Cr₂O₃)_100−x where x = 5, 10, 15, 20, and 25 mol%, respectively, prepared by the melt quenching technique. The room temperature X-ray diffraction spectra revealed certain crystalline phases in the samples. AC conductivity analysis for all the prepared samples was carried out over the frequency range 1 MHz–20 Hz and in the temperature window 297–468 K. The room temperature conductivity values were calculated to be in the order of 10⁻⁵–10⁻³ Scm⁻¹. An Arrhenius dependence of temperature with conductivity was observed, and the activation energies calculated were found to be in the range 0.27–0.31 eV. Furthermore, the total ionic transport number (t _i) values obtained for all these indicated the ionic nature of this system. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7–9, 2006.     

Structural and electrical properties of pure and H<Subscript>2</Subscript>SO<Subscript>4</Subscript> doped (PVA)<Subscript>0.7</Subscript>(NaI)<Subscript>0.3</Subscript> solid polymer electrolyte

Solid polymer electrolytes (SPE) based on poly-(vinyl alcohol) (PVA)_0.7 and sodium iodide (NaI)_0.3 complexed with sulfuric acid (SA) at different concentrations were prepared using solution casting technique. The structural properties of these electrolyte films were examined by X-ray diffraction (XRD) studies. The XRD data revealed that sulfuric acid disrupt the semi-crystalline nature of (PVA)_0.7(NaI)_0.3 and convert it into an amorphous phase. The proton conductivity and impedance of the electrolyte were studied with changing sulfuric acid concentration from 0 to 5.1 mol/liter (M). The highest conductivity of (PVA)_0.7(NaI)_0.3 matrix at room temperature was 10⁻⁵ S cm⁻¹ and this increased to 10⁻³ S cm⁻¹ with doping by 5.1 M sulfuric acid. The electrical conductivity (σ) and dielectric permittivity (ε′) of the solid polymer electrolyte in frequency range (500 Hz–1 MHz) and temperature range (300–400) K were carried out. The electrolyte with the highest electrical conductivity was used in the fabrication of a sodium battery with the configuration Na/SPE/MnO₂. The fabricated cells give open circuit voltage of 3.34 V and have an internal resistance of 4.5 kΩ.     

Impact of ethylene carbonate on electrical properties of PVA/(NH4)2SO4/H2SO4 proton-conductive membrane

A new proton-conductive membrane (PCM) based on poly (vinyl alcohol) and ammonium sulfate (NH₄)₂SO₄ complexed with sulfuric acid and plasticized with ethylene carbonate (EC) at different weight percent were prepared by casting technique. The structural properties of these electrolyte films were examined by XRD studies. The XRD patterns of all the prepared polymer electrolytes reveal the amorphous nature of the films. ac conductivity and dielectric spectra of the electrolyte were studied with changing EC content from weight 0.00 to 0.75 g. A maximum conductivity of 7.3 × 10⁻⁵ S cm⁻¹ has been achieved at ambient temperature for PCM containing 0.25 g of ethylene carbonate. The electrical conductivity σ, dielectric constant ε′ and dielectric loss ε″ of PCM in frequency range (100 Hz to 100 KHz), and temperature range (300–400 K) were carried out. Measurement of transference number was carried out to investigate the nature of charge transport in these polymer electrolyte films using Wagner’s polarization technique. Transport number data showed that the charge transport in these polymer electrolyte systems was predominantly due to ions. The electrolyte with the highest electrical conductivity was used in the fabrication of a solid-state electrochemical cell with the configuration (Mg/PCM/PbO₂). Various cell parameters ldensity, and current density were determined. The fabricated cells gave capacity of 650 μAh and have an internal resistance of 11.6 kΩ.     

Structural,thermal and ion transport studies on nanocomposite polymer electrolyte-{(PEO + SiO<Subscript>2</Subscript>):NH<Subscript>4</Subscript>SCN} system

Development and characterisation of polyethylene oxide (PEO)-based nanocomposite polymer electrolytes comprising of (PEO-SiO₂): NH₄SCN is reported. For synthesis of the said electrolyte, polyethylene oxide has been taken as polymer host and NH₄SCN as an ionic charge supplier. Sol–gel-derived silica powder of nano dimension has been used as ceramic filler for development of nanocomposite electrolytes. The maximum conductivity of electrolyte ∼2.0 × 10⁻⁶ S/cm is observed for samples containing 30 wt.% silica. The temperature dependence of conductivity seems to follow an Arrhenius-type, thermally activated process over a limited temperature range.     

Morphology,chemical interaction,and conductivity of a PEO-ENR50 based on solid polymer electrolyte

A solid polymer electrolytes (SPE) comprising blend of poly(ethylene oxide; PEO) and epoxidized natural rubber as a polymer host and LiCF₃SO₃ as a dopant were prepared by solution-casting technique. The SPE films were characterized by field emission scanning electron microscopy to determine the surface morphology, X-ray diffraction, and differential scanning calorimeter to determine the crystallinity and thermogravimetric analysis to confirm the mass decrease caused by loss of the solvent. While the presence of the complexes was investigated by reflection Fourier transform infrared (ATR-FTIR) spectroscopy. Electrochemical impedance spectroscopy was conducted to obtain ionic conductivity. Scanning electron microscopy analysis showed that a rough surface morphology of SPE became smoother with addition of salt, while ATR-FTIR spectroscopy analysis confirmed the polymer salt complex formation. The interaction occurred between the salt, and ether group of polymer host where the triple peaks of ether group in PEO merged and formed one strong peak at 1,096 cm⁻¹. Ionic conductivity was found to increase with the increase of salt concentration in the polymer blend complexes. The highest conductivity achieved was 1.4 × 10⁻⁴ Scm⁻¹ at 20 wt.% of LiCF₃SO₃, and this composition exhibited an Arrhenius-like behavior with the activation energy of 0.42 eV and the preexponential factor of 1.6 × 10³ Scm⁻¹.     

The effects of ceramic fillers on the PMMA-based polymer electrolyte systems

The effects of ceramics fillers on the polymethylmethacrylate (PMMA)-based solid polymer electrolytes have been studied using ac impedance spectroscopy and infrared spectroscopy. The polymer film samples were prepared using solution cast technique, tetrahydrofuran (THF) used as a solvent, and ethylene carbonate (EC) has been used as plasticizer. Lithium triflate salt (LiCF₃SO₃) has been incorporated into the polymer electrolyte systems. Two types of ceramic fillers, i.e., SiO₂ and Al₂O₃, were then implemented into the polymer electrolyte systems. The solutions were stirred for several hours before it is poured into petri dishes for drying under ambient air. After the film has formed, it was transferred into desiccator for further drying before the test. From the observation done by impedance spectroscopy, the room temperature conductivity for the highest conducting film from the (PMMA–EC–LiCF₃SO₃) system is 1.36 × 10⁻⁵ S cm⁻¹. On addition of the SiO₂ filler and Al₂O₃ filler, the conductivity are expected to increase in the order of ∼10⁻⁴ S cm⁻¹. Infrared spectroscopy indicates complexation between the polymer and the plasticizer, the polymer and the salts, the plasticizer and the salts, and the polymer and the fillers. The interactions have been observed in the C=O band, C–O–C band, and the O–CH₃ band. Paper presented at the Third International Conference on Ionic Devices (ICID 2006), Chennai, Tamilnadu, India, Dec. 7-9, 2006.     

Photovoltaic activity in a ZnSe/PEO–chitosan blend electrolyte junction

Thin films of ZnSe and PEO–chitosan blend polymer doped with NH₄I and iodine crystals were prepared to form the two sides of a semiconductor electrolyte junction. ZnSe was electrodeposited on indium tin oxide (ITO) conducting glass. The polymer is a blend of 50 wt% chitosan and 50 wt% polyethylene oxide. The polymer blend was complexed with ammonium iodide (NH₄I), and some iodine crystals were added to the polymer–NH₄I solution to provide the I⁻/I³⁻redox couple. The room temperature ionic conductivity of the polymer electrolyte is 4.32 × 10⁻⁶ S/cm. The polymer film was sandwiched between the ZnSe semiconductor and an ITO glass to form a ZnSe/polymer electrolyte/ITO photovoltaic cell. The open circuit voltage (V _oc) of the fabricated cells ranges between 200 to 400 mV and the short circuit current between 7 to 10 μA.