任意相移阴影叠栅相位解调技术的研究

结合时域和频域干涉图分析方法,提出一种任意相移阴影叠栅条纹图相位解调技术,降低了干涉图在采样过程中对相移量的严格标定要求,补偿了相移阴影叠栅技术固有的相移不匀误差。使用空域技术确定采样干涉图的正交信号,进而得到了采样干涉图的相移量,然后运用任意相移相位提取算法搜索测量相位信息。实验证明此方法简单方便、求解迅速,且优于典型的相移算法,其测量误差的标准差不超过3×10-3 mm,该方法为提高相移阴影叠栅技术的测量精度提供了有效手段。     

基于傅里叶变换的高精度条纹细分方法

针对传统傅里叶变换法在提取条纹图相位中存在的能量泄漏问题,提出了条纹图整周期裁剪的方法,可有效抑制能量泄漏对检相精度的影响,提高傅里叶变换法相位计算的精度。在此基础上,提出了一种基于傅里叶变换时移特性的叠栅条纹细分新方法。与传统傅里叶变换法相比,该方法求取相邻两帧条纹图间的相移,只需经过两次傅里叶变换,不需要截取条纹图的基频再逆变换回空域,因此计算量至少减少了一倍,计算速度大大提高。数值计算结果表明,对两束单色平面波形成的条纹,理想条件下细分精度高达10-12量级;对高斯包络调制的条纹,细分精度至少可达10-3量级。     

提高数字式干涉型光纤传感器条纹细分的研究

本文提出了一种新颖的对数字式干涉型光纤传感器的条纹进行直接细分的方案,研究了实现这一方案的原理和方法,与叠栅光栅检测中的条纹直接细分相比,细分数得到显著提高.     

提高数字式与干涉型光纤传感器条纹细分的研究

本文提出了一种新颖的对数字式干涉型光纤传感器的条纹进行直接细分的方案,研究了实现这一方案的原理和方法,与叠栅光栅检测中的条纹直接细分相比,细分数得到显著提高。     

一种多距离融合的大深度测量范围相移阴影叠栅轮廓术

针对传统阴影叠栅轮廓术深度测量范围有限的问题,根据阴影叠栅条纹对比度的变化特点,提出了大深度范围内的阴影叠栅轮廓新型测量方法。该方法将光栅置于不同的高度,在物体表面形成叠栅条纹,通过将不同高度范围内的条纹相位测量结果相互融合,实现了大深度范围内的阴影叠栅轮廓测量。分析了光栅处于不同位置时叠栅条纹的相位分布特点,提出了基于重叠区域的相位融合方法和误差补偿方法。通过实验验证了所提出方法的可行性和准确性。     

使用叠栅层析技术测量超音速风洞中的非对称复杂密度场

使用叠栅层析技术解决超音速风洞中复杂密度场的测量难题。应用高灵敏度叠栅偏折仪和间隔角度旋转模型的方法获取超音速风洞中流场的多方向叠栅条纹图。层析计算中使用一种新的偏折角修正迭代的叠栅层析算法,该方法可以实现对有限角采样和包含遮挡物的非完全数据重建,迭代过程中结合内边界平滑滤波提高重建精度。实验中获取了马赫数为2.52的超音速风洞中9幅不同采样角的条纹图,经过50次迭代计算后重建出膨胀波区非对称密度场的截面分布,并对测量结果和误差进行了分析和讨论。使用计算流体力学技术对该密度场进行建模和计算,验证了叠栅层析重建结果的正确性,证实了该技术在测量复杂流场领域的重要价值。     

双螺旋叠栅条纹检测光束准直性的两种方法

介绍双螺旋叠栅条纹检测光束准直性的基本原理,进一步就双螺旋叠栅条纹的特征参量与被测光束发散角(即光束准直精度)的关系进行分析和推导。在分析双螺旋叠栅条纹进行时,首先采用频域低通滤波提取纯叠栅条纹,然后提取纯叠栅条纹的特征参量。提出两种特征参量的提取方法,一种依次进行傅里叶变换计算相位信息的傅里叶变换方法,另一种是受传统时间相移算法启发而提出的空间相移算法,讨论了在两种方法中极坐标的重采样问题和相应的计算公式,并进行了计算机模拟。结果表明,傅里叶变换方法和空间相移算法实质都是获取叠栅条纹全场趋势的平均值,使最终光束发散角的检测具有很高的精度,对自成像条纹周期的检测误差在±2.8‰以内。     

提高叠栅条纹信号质量的一种新方法

在国内外普遍使用的细栅距幅光栅叠栅条纹系统中,衍射效应是很明显的,这是造成叠栅条纹信号的衬比(度)和正弦性不好的主要原因.本文在分析了叠栅条纹信号的基础上,导出了衍射光栅副中±1级叠栅条纹的相位与光栅副间隔,光线入射角等的关系,提出了用±1级叠栅条纹来提高叠栅条纹的信号质量,实验结果与理论分析一致,实际应用,效果良好.     

不同结构绝对光栅尺的误码机制研究

针对光栅尺具有断电位置复位、无累计误差、高精度优点,在光学隔振平台上分别建立开放式和封闭式绝对光栅尺实验系统,绝对光栅尺采用图像识别原理,以气浮直线电机ArotechABL1500为参考对象,使用激光干涉仪RENISHAW XL-80校核精度,研究不同结构绝对光栅尺的误码特点及原因。通过对比实验及研究分析,表明封闭式绝对尺相对于开放式绝对尺的误码率要高,开放式绝对式光栅尺的误码率为3%,封闭式绝对式光栅尺的误码率为8%。     

一种新的光栅仪器误差修正方法

<正> 一般来说,使用光栅尺为基准的高精度仪器,由于光栅尺制造精度不能满足仪器总精度要求,就要考虑对光栅仪器或光栅尺制造偏差进行修正。常见的光栅仪器误差修正方法是按要求给副光栅一个附加位移,或者是用光学扫描方法,使副光栅的象在光栅尺上有一个微小位移。这里介绍一种新的方法。这种方法与前两种方法相比,能收到修正机构制造精度低和仪器结构简单而获得修正后残差小的效果。根据光栅幅工作原理,当光栅幅的主副光栅相对位移一个栅节距时,光栅幅形成的莫尔条纹也相应位移一个条纹宽度。如果给接收莫     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Hybrid Wavelength and Code Division Multiple Access in Optical Networks

A review of schemes for multiple access in fiber optic networks shows that a hybrid of wavelength and code division multiple access (WCDMA) combines the best features of both. In particular, the hybrid scheme retains the large information carrying capacity of wavelength division multiple access (WDMA) and flexibility of code division multiple access (CDMA). In this paper WDMA, optical CDMA (OCDMA), and WCDMA networks are discussed. In OCDMA networks, concept of incoherent and coherent coding including inverse decoding and matched filter is introduced. The delay performance of both WDMA and WCDMA networks, under the simple suboptimum access protocols based on cyclic search, is computed. It has been shown quantitatively that tuning delay significantly affects the delay performance of both WDMA and WCDMA networks. Futhermore, delay performance of WCDMA networks is always better than the WDMA networks for the same tuning delay, load, and number of users.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Research on beamforming method for dual-line array with space mismatch between the two line arrays

The performance of port/starboard discrimination of dual-line array will be seriously degraded when the space between the two line arrays of the dual-line array is mismatched. The directivity function of the delay-sum and delay-subtract beamforming is deduced and the port/starboard discrimination of the delay-sum and delay-subtract beamforming is also studied both under the ideal status and the status under which the space between the two line arrays of the dual-line array is mismatched. Analysis results show the delay-subtract beamforming has better performance of port/starboard discrimination. At last, the sea trial results demonstrate the theoretical results.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Retrieval of ultraviolet skylight radiances and O3 slant column densities from balloon-borne limb spectrometer

With a novel light-weight and absolutely calibrated ultraviolet （UV） spectrometer, UV skylight radiances and O3 slant column densities are measured by balloon-borne limb measurements in Xinjiang area, China. UV skylight radiances measured at the height of 31 km are compared with the results from Modtran in the wavelength range from 290 to 420 nm. O3 slant column densities are derived from radiance spectra in the Huggins bands （320 - 335 nm） using differential optical absorption spectroscopy method. And the parameter exhibits a good correlation with the same value simulated by radiative transfer model （Tracy）. The O3 profile simultaneously measured by an O3 sonde is used as input in Tracy calculations. The O3 sonde is launched on the same balloon.     

Design optimization of highly sensitive LSPR enhanced surface plasmon resonance biosensors with nanoholes

For breaking through the sensitivity limitation of conventional surface plasmon resonance (SPR) biosensors, novel highly sensitive SPR biosensors with Au nanoparticles and nanogratings enhancement have been proposed recently.But in practice, these structures have obvious disadvantages.In this study, a nanohole based sensitivity enhancement SPR biosensor is proposed and the influence of different structural parameters on the performance is investigated by using rigorous coupled wave analysis (RCWA).Electromagnetic field distributions around the nanohole are also given out to directly explain the performance difference for various structural parameters.The results indicate that significant sensitivity increase is associated with localized surface plasmons (LSPs) excitation mediated by nanoholes.Except to outcome the weakness of other LSP based biosensors, larger resonance angle shift, reflectance amplitude, and sharper SPR curves' width are obtained simultaneously under optimized structural parameters.     

Polymer gratings based on photopolymerization for low-order distributed feedback polymer lasers

Novel polymer distributed feedback(DFB)gratings are fabricated based on photopolymerization to reduce lasing threshold of polymer lasers.A photopolymer formulation sensitive to 355-nm ultraviolet(UV)light is proposed for the fabrication of polymer gratings and it can be used to form polymer films by spin-coating process.A very low surface-relief depth ranging from 12.5 to about 1.0 nm has been demonstrated with a refractive-index modulation of about 0.012.The experimental results indicate that such polymer gratings have promising potentials for the fabrication of low-order DFB organic semiconductor lasers.