Film-forming ability and mechanical properties of coalesced latex blends

The film-forming ability of latex blends (hard latex + soft latex) and the mechanical behavior at finite strain of latex blend films (soft matrix with tough inclusions) has been investigated. The maximum weight fraction of hard latex particles (ϕ_max) which still gives rise to transparent and crack-free films has been used as film-forming ability criterion. It was shown that when the T_g of the soft latex is low (T_g(soft) < 0°C), ϕ_max is constant and equal to 0.55 because the film-forming ability is controlled by contacts between hard particles. Nevertheless, the expected effect of T_g(soft) on film-forming ability is observed (i.e., ϕ_max decreases when T_g(soft) increases) when T_g(soft) is above 0°C. From the mechanical behavior point of view, it was shown that the two main parameters controlling the mechanical behavior of latex blend films are: the mechanical properties of the soft polymer because it represents the continuous matrix and the weight fraction of hard latex particles since they enhance the local deformation of matrix under load. However, it was also proven that debounding between the T_g latex particles and low T_g matrix occurs rapidly (at an elongation ratio ≈ 30%) during uniaxial strain experiments and has to be taken into account in order to gain a thorough understanding of the mechanical behavior of these biphasic films. © 1997 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 35: 2093–2101, 1997     

Miscible blends containing a crystallizable component: poly(vinyl alcohol)/poly(ethyleneimine)

Blends of poly(vinyl alcohol) (PVAI) with poly(ethyleneimine) (PEI) were prepared by casting from a common solvent. All blends show a single, composition dependent glass transition temperature (T_g), indicating that the blends are miscible in the amorphous state and in the melt. The overall crystallization rate of PVAI in the blend decreases with increasing PEI content. The crystallinity index of PVAI in the blend does not decrease greatly with PEI content up to a composition of 70/30 PVAI/PEI, since the T_g of the crystallizable component PVAI is larger than that of the non-crystallizable component PEI. The T_g of the system PVAI/PEI decreases with increasing PEI content. The interaction parameter B of the two polymers in the melt was found to be −24 J/cm³.     

DSC and spectroscopic investigation of human serum albumin adsorbed onto silica nanoparticles functionalized by amino groups

Human serum albumin (HSA) adsorbed onto silica nanoparticles modified by 3-aminopropyltriethoxysilane (APTES) and polyethyleneimine (PEI) was investigated by differential scanning calorimetry, IR spectroscopy, and photon correlation spectroscopy. The structural alterations of the protein molecules induced from adsorption process were estimated on the basis of temperatures of denaturation transition (T _d) of the protein in free (native) and adsorbed form. It was found that adsorption of the protein onto the APTES-modified silica nanoparticles results in an increase in the temperature of denaturation transition from 42 to 47.4 °C. HSA adsorbed onto the PEI-modified silica nanoparticles unfolds extensively.     

Development of novel cardo‐containing phenylethynyl‐terminated polyimide with high thermal properties

A phenylethynyl‐terminated reactive diluent [Card‐4‐phenylethynylphthalic anhydride (PEPA)], which contained fluorenyl cardo structures, was successfully synthesized and used as a modifier for flexible phenylethynyl‐terminated imide oligomer (PEI‐PEPA). The chemical structure, crosslink characterization, molecular weights, and thermal properties of the products were characterized. The imide systems with addition of 10, 20, 30, and 40 wt% Card‐PEPA to PEI‐PEPA (PEI‐PEPA‐Card) and their cured resin systems were prepared. The thermal curing behaviors of imide systems at different heating rates were analyzed by using differential scanning calorimetry. Thermal properties such as glass transition temperature (T_g) and char yield at 800°C of the resultant resin systems were studied by differential scanning calorimetry, dynamic mechanical analysis, and thermogravimetric analysis. The rheological properties were also investigated using a dynamic rheometry. These properties were found to be outstanding compared with pure PEI‐PEPA. The uncured imide systems exhibited lower T_g and lower isothermal viscosity with addition of Card‐PEPA. Furthermore, the T_g and char yield of the cured resin systems increased with addition of Card‐PEPA. The cured resin systems containing 40 wt% Card‐PEPA exhibited the highest T_g of 359°C and char yield at 800°C of 66.5%. Copyright © 2016 John Wiley & Sons, Ltd.     

Blends of a novel high-temperature poly(oxy-1,4′-diphenyleneoxy-1,4-phenylenecarbonyl-1,4-phenylene) with poly(ether imide): structure, interaction, and miscibility

 Polymer miscibility has been discovered in a blend system comprising poly(ether imide) (PEI) and a new poly(ether diphenyl ether ketone) (PEDEK). The miscibility of the PEDEK/PEI polymer system (quenched from the molten state) was investigated in this study using differential scanning calorimetry and Fourier transform (FT-IR) spectroscopy. A composition-dependent single glass-transition temperature (T _g) in the PEDEK/PEI blends over a full composition range was observed; the sharp transition width and the T _g–composition relationship both suggest that the scale of mixing is fine and uniform. Evidence based on observation of the cold-crystallization peak and suppression of the blend crystallinity and melting peak also indicated intimate intermolecular mixing. The FT-IR result yielded further evidence that the physical interactions leading to miscibility were weak, with no apparent specific interactions between the constituent polymers. Relationships between structures and interactions responsible for the miscibility in PEI and several ether-ketone-type polymers are briefly discussed. Received: 8 July 1999 Accepted in revised form: 21 October 1999     

A fluorescence approach to investigate repartitioning of coalescing agents in acrylic polymer emulsions

Repartitioning of co-solvents between particles of latex emulsions was investigated by means of a fluorescence method based on the detection of the amount of co-solvent via the solvatochromic shift of the emission maximum of a fluorescent probe, copolymerized at a low concentration. Complete repartitioning of co-solvents between particles of latex materials with a low T _g (ca. 25 °C) occurred within minutes. For a hydrophilic latex with a T _g of 68 °C, equilibration was achieved within an hour. Repartitioning was faster for more hydrophobic co-solvents. For a hydrophobic latex of similar T _g , co-solvent repartitioning took place on the same time scale, but complete equilibration was not reached. Possibly, there is an additional slow component in the repartitioning, or the prolonged presence of co-solvent causes a structural change in the latex particles that affects the outcome of the experiment.     

Synthesis and property comparison of isomeric AB‐type homo‐ and copoly(etherimide)s

AB‐type homo‐ and copoly(etherimide)s were prepared by the polymerization of 3‐ and 4‐(3,4‐dicarboxyphenyloxy)aniline hydrochlorides ( 3A and 4A ) at 160 °C in dimethylacetamide in the presence of triethylamine and triphenyl phosphite. After the structures of the polymers were characterized, their solubilities, ultraviolet–visible (UV–vis) absorption behaviors, thermal properties, and crystallinities were measured, and these properties are discussed with respect to the structure of the homopolymers and the composition of the copolymers. Poly(etherimide) (PEI) derived from 3A [PEI( 3A )] was amorphous and soluble in chloroform on heating, whereas that derived from 4A [PEI( 4A )] was crystalline and insoluble in common organic solvents even on heating. In UV–vis absorption spectra, PEI( 4A ) showed a small bathochromic shift relative to N‐phenylphthalimide, but PEI(3A) did not. PEI(3A) revealed a glass‐transition temperature (T_g) at 195 °C, but no T_g was detectable for PEI( 4A ). All the measured physical properties of the copoly(etherimide)s showed a good dependence on their composition between PEI( 3A ) and PEI( 4A ). © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 402–410, 2000     

Effect of alkyl side chain length on the properties of polyetherimides from molecular simulation combined with experimental results

Three polyetherimides (PEIs) with the same backbone of Ultem 100 but different lengths of the alkyl side chains were simulated by using molecular dynamics and molecular mechanics techniques to investigate the effect of side chain length on their properties and physical mechanism behind. Simulation results, which are consistent to the experimental data, show that PEI‐5 with four methylene units in each alkyl side chain has higher T_g (glass transition temperature) and higher tensile strength, but lower tensile elongation at break than those of PEI‐6 with five and PEI‐8 with seven methylene units in each alkyl side chain. However, unlike the traditional phenomena, conformational analysis provides that PEI‐5 with the highest T_g gives the highest flexibility to the polymer chain, whereas PEI‐8 with the lowest T_g imparts the lowest flexibility resulting from attachment of longer alkyl side chain increase the rigidity of backbone. From the calculated ratio of the accessible volume to the total volume for each system, the highest ratio of PEI‐8 indicates that long alkyl side chains generate more free volume than short side chains, acting as an internal plasticizer in bulk structure. It is the internal plasticizing effect that is predominantly responsible for the abnormal properties, instead of the rigidity from side chains. © 2010 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 48: 595–599, 2010     

Anisotropic Self‐Assembly of Citrate‐Coated Gold Nanoparticles on Fluidic Liposomes

The behavior of self‐assembly processes of nanoscale particles on plasma membranes can reveal mechanisms of important biofunctions and/or intractable diseases. Self‐assembly of citrate‐coated gold nanoparticles (cAuNPs) on liposomes was investigated. The adsorbed cAuNPs were initially fixed on the liposome surfaces and did not self‐assemble below the phospholipid phase transition temperature (T_m). In contrast, anisotropic cAuNP self‐assembly was observed upon heating of the composite above the T_m, where the phospholipids became fluid. The number of self‐assembled NPs is conveniently controlled by the initial mixing ratio of cAuNPs and liposomes. Gold nanoparticle protecting agents strongly affected the self‐assembly process on the fluidic membrane.     

Determination of interactions between aryl polyesters and poly(ether imide) via glass transition temperatures of separated phases in immiscible blends

Phase behavior in domains of immiscible blends of poly(pentamethylene terephthalate)/poly(ether imide) (PPT/PEI) and poly(hexamethylene terephthalate)/poly(ether imide) (PHT/PEI) were investigated using differential scanning calorimetry (DSC). The measured glass transition temperature (T _g) reveals that aryl polyesters dissolve more in the PEI-rich phase than the PEI does in the aryl polyester-rich phase, for both PPT/PEI and PHT/PEI systems. Additionally, optical microscopy supports the conclusion that PPT (or PHT) dissolves more in the PEI-rich phase than PEI does in the PPT-rich (or PHT-rich) phase in the aryl polyester/PEI blends. Furthermore, the Flory–Huggins interaction parameters (χ₁₂) for the PPT/PEI and the PHT/PEI blends were calculated to be 0.12 and 0.17, respectively. For the blend systems comprising of PEI and homologous aryl polyesters, the value of χ₁₂ exhibits a trend of variation with respect to structure of aryl polyesters. For the PPT/PEI and PHT/PEI blends, investigated in this study, value of the polymer–polymer interaction parameter (χ₁₂) between the aryl polyester and the PEI was found to be positive, which increases with the number of methylene moieties in the repeating unit of the aryl polyester, ultimately resulting in phase separation observed.     

Rubber toughening of poly(ether imide) by modification with poly(butylene terephthalate)

Rubber toughening of poly(ether imide) (PEI) has been elusive up to now due to the high processing temperature of PEI, which leads to degradation of the rubber. In this study, by profiting from the miscibility between PEI and poly(butylene terephthalate) (PBT), and the low T_g of PBT, we prepared a blend by melt extrusion with 20 wt% PBT in an attempt to render it toughenable by decreasing its T_g and processing temperature. The PEI-rich blend was subsequently mixed with maleic anhydride (0.9 wt%) grafted poly(ethylene-octene) copolymer (mPEO) up to 30 wt%. The decrease in T_g and processing temperature resulted in no observable degradation of the mPEO, and to the formation of a homogeneous morphology of rubber particles with a fine particle size, indicating that compatibilization was achieved. Upon rubber addition, stiffness decreased, while a very large toughness increase occurred with only 15% mPEO (impact strength more than 10-fold that of the PEI-PBT matrix). Upon observation of the fracture surface, the increase in impact strength was attributed partially to the cavitation and debonding of the rubber particles, and mostly to the deformation and yielding of the PEI-PBT matrix.     

Controlling the thermomechanical properties of polymer nanocomposites by tailoring the polymer–particle interface

We show that the thermomechanical properties of polymer nanocomposites are critically affected by polymer-particle wetting behavior. Silica nanoparticles grafted with dense polystyrene brushes of degree of polymerization 1050 are blended with polystyrene melts to form nanocomposites. It was found that low molecular weight (MW) polystyrene melts with lengths <880 wet these particles. Concurrently, the glass transition temperature (T_g) of the nanocomposite increases. At higher MW, the matrix does not wet the particles and the T_g decreases. © 2006 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 44: 2944–2950, 2006     

Synthesis and Application of Low Molecular Weight PEI-Based Copolymers for siRNA Delivery with Smart Polymer Blends

Polyethylenimine (PEI) is a commonly used cationic polymer for small-interfering RNA (siRNA) delivery due to its high transfection efficiency at low commercial cost. However, high molecular weight PEI is cytotoxic and thus, its practical application is limited. In this study, different formulations of low molecular weight PEI (LMW-PEI) based copolymers polyethylenimine-g-polycaprolactone (PEI–PCL) (800 Da–40 kDa) and PEI–PCL–PEI (5–5–5 kDa) blended with or without polyethylene glycol-b-polycaprolactone (PEG–PCL) (5 kDa-4 kDa) are investigated to prepare nanoparticles via nanoprecipitation using a solvent displacement method with sizes ≈100 nm. PEG–PCL can stabilize the nanoparticles, improve their biocompatibility, and extend their circulation time in vivo. The nanoparticles composed of PEI–PCL–PEI and PEG–PCL show higher siRNA encapsulation efficiency than PEI–PCL/PEG–PCL based nanoparticles at low N/P ratios, higher cellular uptake, and a gene silencing efficiency of ≈40% as a result of the higher molecular weight PEI blocks. These results suggest that the PEI–PCL–PEI/PEG–PCL nanoparticle system could be a promising vehicle for siRNA delivery at minimal synthetic effort.     

Glass transition temperature of polymer nanocomposites: Prediction from the continuous‐multilayer model

The continuous‐multilayer model introduced in our previous study for the T_g behavior of thin films is adapted to nanocomposite systems. T_g enhancement in both thin films and nanocomposites with attractive interfacial interactions can be explained by the same model. Various shapes of nanoparticles are proposed to rationalize the adaptation of the one‐dimensional model for the T_g behavior of thin film to three‐dimensional system such as nanocomposite. The tendency of predicted T_g enhancements in poly(methyl methacrylate) and P2VP nanocomposites with silica particles are qualitatively fit to experimental data in literatures. For the further quantitative fitting, the model is partially modified with the consideration for other factors affecting T_g deviation in nanocomposite. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2281–2287, 2009     

Thermal and FTIR investigation of freeze-dried protein-excipient mixtures

The effect of excipients on the secondary structure of lyophilized proteins was studied through second-derivative Fourier transform infrared (FTIR) spectroscopic analysis. The glass transition temperature (T _g), denaturation temperature (T _d) and moisture content were determined by differential scanning calorimetry (DSC) and thermogravimetry (TG). T _g, T _d and the preservation of protein secondary structure were found to be dependent upon the type and amount of the excipient included in the formulation. Meanwhile, the lyophilized proteins easily adsorbed amounts of moisture during storage to reduce their T _gs and stability.     

Structure and properties of poly(methyl methacrylate) particles prepared by a modified microemulsion polymerization

Nanoscale poly(methyl methacrylate) (PMMA) particles were prepared by modified microemulsion polymerization. Different from particles made by traditional microemulsion polymerization, the particles prepared by modified microemulsion polymerization were multichain systems. PMMA samples, whether prepared by the traditional procedure or the modified procedure, had glass-transition temperatures (T_g's) greater than 120 °C and were rich in syndiotactic content (55–61% rr). After the samples were dissolved in CHCl₃, there were decreases in the T_g values for the polymers prepared by the traditional procedure and those prepared by the modified process. However, a more evident T_g decrease was observed in the former than in the latter; still, for both, T_g was greater than 120 °C. Polarizing optical microscopy and wide-angle X-ray diffraction indicated that some ordered regions formed in the particles prepared by modified microemulsion polymerization. The addition of a chain-transfer agent resulted in a decrease in both the syndiotacticity and T_g through decreasing polymer molecular weight. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 733–741, 2004     

Controlled/living radical polymerization of isoprene and butadiene in emulsion

A process for RAFT-controlled radical polymerization in emulsion [36] has been applied to the polymerizations of isoprene and of butadiene in emulsion systems, with the goal of producing latex particles containing block copolymers of acrylic acid (stabilizer and starting polymer), styrene (second polymer) and isoprene or butadiene (third polymer). The microstructure of the polymer chains was examined using dual-detection size-exclusion chromatography, and the nanostructure of the materials was investigated by differential scanning calorimetry and solid-state nuclear magnetic resonance. Reactions were always slow (although faster than the corresponding processes in solution), and exhibited limited reinitiation by isoprene when in emulsion. The materials containing isoprene exhibit a nanostructure with a phase separation into high-T_g polystyrene-rich domains and low-T_g polyisoprene-rich domains, revealed by DSC and NMR. This has the potential to lead to barrier materials with novel physical properties.     

Decoration of Fe3O4 nanoparticles on the surface of poly(acrylic acid) functionalized multi‐walled carbon nanotubes by covalent bonding

Fe₃O₄ nanoparticles were indirectly implanted onto functionalized multi‐walled carbon nanotubes (MWCNTs) leading to a nanocomposite with stronger magnetic performance. Poly(acrylic acid) (PAA) oligomer was first reacted with hydroxyl‐functionalized MWCNTs (MWCNTs‐OH) forming PAA‐grafted MWCNTs (PAA‐g‐MWCNTs). Subsequently, Fe₃O₄ nanoparticles were attached onto the surface of PAA‐g‐MWCNTs through an amidation reaction between the amino groups on the surface of Fe₃O₄ nanoparticles and the carboxyl groups of PAA. Fourier transform infrared spectra confirmed that the Fe₃O₄ nanoparticles and PAA‐g‐MWCNTs were indeed chemically linked. The morphology of the nanocomposites was characterized using transmission electron microscope (TEM). The surface and bulk structure of the nanocomposites were examined using X‐ray diffraction, X‐ray photoelectron spectrometer (XPS), and thermogravimetric analysis (TGA). The magnetic performance was characterized by vibrating sample magnetometer (VSM) and the magnetic saturation value of the magnetic nanocomposites was 47 emu g^?1. The resulting products could be separated from deionized water under an external magnetic field within about 15 s. Finally, the magnetorheological (MR) performances of the synthesized magnetic nanocomposites and pure Fe₃O₄ nanoparticles were examined using a rotational rheometer. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Vitrification/devitrification phenomena during isothermal and nonisothermal crystallization of poly(aryl–ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) blends

We have established time–temperature transformation and continuous-heating transformation diagrams for poly(ether–ether–ketone) (PEEK) and PEEK/poly(ether–imide) (PEI) blends, in order to analyze the effects of relaxation control on crystallization. Similar diagrams are widely used in the field of thermosetting resins. Upon crystallization, the glass transition temperature (T_g) of PEEK and PEEK/PEI blends is found to increase significantly. In the case of PEEK, the shift of the α-relaxation is due to the progressive constraining of amorphous regions by nearby crystals. This phenomenon results in the isothermal vitrification of PEEK during its latest crystallization stages for crystallization temperatures near the initial T_g of PEEK. However, vitrification/devitrification effects are found to be of minor importance for anisothermal crystallization, above 0.1°C/min heating rate. In the case of PEEK/PEI blends, amorphous regions are progressively enriched in PEI upon PEEK crystallization. This promotes a shift of the α-relaxation of these regions to higher temperatures, with a consequent vitrification of the material when crystallized below the T_g of PEI. The data obtained for the blends in anisothermal regimes allow one to detect a region in the (temperature/heating rate) plane where crystallization proceeds in the continuously close proximity of the glass transition (dynamic vitrification). These experimental findings are in agreement with simple simulations based on a modified Avrami model coupled with the Fox equation. © 1998 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 36: 919–930, 1998     

Preparation of composite particles with magnetic silica core and fluorescent polymer shell

Dual functions of magnetic and fluorescent properties were created in composite particles that incorporated magnetite (Fe₃O₄) nanoparticles in particle cores of silica and fluorescent pyrene in particle shells of polystyrene. The Fe₃O₄ nanoparticles were prepared with a conventional homogeneous precipitation method and surface modified with a coupling agent of carboxyethylsilanetriol. The silica particles incorporating Fe₃O₄ nanoparticles were synthesized with a modified Stöber method in which the Fe₃O₄ nanoparticles were added to a system of tetraethylorthosilicate (TEOS)/ammonia/water/ethanol. Then, the magnetite/silica composite particles were coated with the pyrene/polystyrene shell in a soap-free emulsion polymerization, which was conducted in the presence of pyrene in a mixed solvent of water/ethanol. The composite particles prepared in the mixed solvent had both magnetic and fluorescent properties. The fluorescent spectrum of the particles with Fe₃O₄ was very similar to that without Fe₃O₄, indicating that the magnetic component within the core particles scarcely interfered with the fluorescent emission from the polymer shell.