Comparative studies of neodymium (III)-selective PVC membrane sensors

Sensors based on two neutral ionophores, N,N′-bis((1H-pyrrol-2-yl)methylene)cyclohexane-1,2-diamine (L₁) and 3,3′-(cyclohexane-1,2-diylbis(azan-1-yl-1-ylidene)bis(methan-1-yl-1-ylidene)bis(5-hydroxymethyl)pyridine-2-ol) (L₂) are described for quantification of neodymium (III). Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), dibutyl butylphosphonate (DBBP), tri-n-butyl phosphates (TBP), dioctylpthalate (DOP) and chloronapthalen (CN) and anion excluder, sodiumtetraphenylborate (NaTPB) has been studied. The membrane composition of PVC:o-NPOE:ionophore (L₁):NaTPB (w/w; mg) of 150:300:5:5 exhibited best performance. The sensor with ionophore (L₁) exhibits significantly enhanced selectivity towards neodymium (III) in the concentration range 5.0 × 10⁻⁷ to 1.0 × 10⁻² M with a detection limit of 1.0 × 10⁻⁷ M and a Nernstian compliance (19.8 ± 0.3 mV decade⁻¹ of activity) within pH range 4.0-8.0. The response time of sensor was found as 10 s. The influence of the membrane composition and possible interfering ions has also been investigated on the response properties of the electrode. The fast and stable response, good reproducibility and long-term stability of the sensor are observed. The sensor has been found to work satisfactorily in partially non-aqueous media up to 20% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients determined by using fixed interference method (FIM) indicate high selectivity for neodymium. The proposed electrode shows fairly good discrimination of neodymium (III) from other cations. The application of prepared sensor has been demonstrated in the determination of neodymium (III) in spiked water samples.     

Comparative studies of praseodymium(III) selective sensors based on newly synthesized Schiff's bases

Praseodymium ion selective polyvinyl chloride (PVC) membrane sensors, based on two new Schiff's bases 1,3-diphenylpropane-1,3-diylidenebis(azan-1-ylidene)diphenol (M₁) and N,N′-bis(pyridoxylideneiminato) ethylene (M₂) have been developed and studied. The sensor having membrane composition of PVC: o-NPOE: ionophore (M₁): NaTPB (w/w; mg) of 150: 300: 8: 5 showed best performances in comparison to M₂ based membranes. The sensor based on (M₁) exhibits the working concentration range 1.0 × 10⁻⁸ to 1.0 × 10⁻² M with a detection limit of 5.0 × 10⁻⁹ M and a Nernstian slope 20.0 ± 0.3 mV decade⁻¹ of activity. It exhibited a quick response time as <8 s and its potential responses were pH independent across the range of 3.5-8.5.The influence of the membrane composition and possible interfering ions have also been investigated on the response properties of the electrode. The sensor has been found to work satisfactorily in partially non-aqueous media up to 15% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients determined by using fixed interference method (FIM) indicate high selectivity for praseodymium(III) ions over wide variety of other cations. To asses its analytical applicability the prepared sensor was successfully applied for determination of praseodymium(III) in spiked water samples.     

Manganese (II) selective PVC based membrane sensor using a Schiff base

N,N′,N″,N′′′-1,5,8,12-tetraazadodecane-bis(salicylaldiminato)(H₂L) has been used as ionophore for preparing Mn²⁺ selective sensor. Membranes of different composition with regard to ratio of H₂L:PVC:NPOE:NaTPB have been prepared and investigated. The best performance was obtained with the membrane of composition 10:150:150:10 (H₂L:PVC:NPOE:NaTPB) (w/w; mg). This membrane generated linear potential response in the concentration range of 5.0 × 10⁻⁶ to 1.0 × 10⁻¹ M with a Nernstian slope of 30.0 mV/decade of activity and fast response time (10 s). Hydrogen ion does not effect to the performance of sensor in the pH range 3.0-6.5. The sensor was found to be sufficient selective for Mn²⁺ over a number of alkali, alkaline and heavy metal ions and could therefore be used for the determination of manganese in various samples by direct potentiometry.     

Chromium(III) selective membrane sensors based on Schiff bases as chelating ionophores

The two chromium chelates of Schiff bases, N-(acetoacetanilide)-1,2-diaminoethane (L₁) and N,N′-bis(acetoacetanilide)-triethylenetetraammine (L₂), have been synthesized and explored as neutral ionophores for preparing poly(vinylchloride) (PVC) based membrane sensors selective to Cr(III). The addition of lipophilic anion excluder (NaTPB) and various plasticizers viz. o-Nitrophenyloctyl ether (o-NPOE), dioctylpthalate (DOP), dibutylphthalate (DBP), tris(2-ethylhexyl)phosphate (TEHP), and benzyl acetate (BA) have found to improve the performance of the sensors. The best performance was obtained for the membrane sensor having a composition of L₁:PVC:DBP:NaTPB in the ratio 5:150:250:3 (w/w). The sensor exhibits Nernstian response in the concentration range 8.9 × 10⁻⁸ to 1.0 × 10⁻¹ M Cr³⁺ with limit of detection 5.6 × 10⁻⁸ M. The proposed sensor manifest advantages of relatively fast response (10 s) and good selectivity over some alkali, alkaline earth, transition and heavy metal ions. The selectivity behavior of the proposed electrode revealed a considerable improvement as compared to the best previously PVC-membrane electrode for chromium(III) ion. The potentiometric response of the proposed sensor was independent of pH of the test solution in the range of 2.0-7.0. The sensor has found to work satisfactorily in partially non-aqueous media up to 20% (v/v) content of methanol, ethanol and acetonitrile and could be used for a period of 3 months. The proposed electrode was used as an indicator electrode in potentiometric titration of chromium ion with EDTA and in direct determination in different water and food samples.     

Comparative studies on Tb (III)-selective PVC membrane sensors

A new terbium selective sensor based on N-(2-hydroxyphenyl)-3-(2-hydroxyphenylhydroxyphenylimino)-N-phenylbutanamidine (L₁) and N,N′-bis((1H-indole-3-yl)methylene)butane-1,4 diamine (L₂) as a ionophore is reported. Effect of various plasticizers; 2-nitrophenyloctylether (o-NPOE), dibutyl butylphosphonate (DBBP), chloronaphthelene (CN), dioctylphthalate (DOP) and tri-(2-ethylhexyl)phosphate (TEHP) with anion excluder, potassium tetrakis (p-chloropheny1)borate (KTpClPB) have been studied. The membrane with a composition of ionophore (L₁):KTpClPB:PVC:o-NPOE (w/w, %) in ratio of 3.0:5.0:30.0:62.0 exhibited enhanced selectivity towards terbium ions (III) in the concentration range of 3.5 × 10⁻⁷ to 1.0 × 10⁻² M with a detection limit of 1.2 × 10⁻⁷ M and a Nernstian slope (20.0 ± 0.5 mV dec⁻¹ activity). The sensors showed the working pH range to be 3.5-7.5 with response time of 11 s. The sensor has been found to work satisfactorily in partially non-aqueous media up to 15% (v/v) content of methanol, ethanol or acetonitrile and could be used for a period of 3 months. The selectivity coefficients indicated high selectivity for terbium (III). The fast and stable response, good reproducibility and long-term stability of the sensors were observed. The application of the sensor has been demonstrated in determination of terbium (III) ions in spiked water samples.     

Strontium(II)-selective electrode based on a macrocyclic tetraamide

A new PVC membrane electrode based on 5,7,12,14-dibenzo-2,3,9,10-tetraoxa-1,4,8,11-tetraazacyclotetradecane (I) as an ion carrier, o-nitrophenyloctyl ether (o-NPOE) as solvent mediator and sodium tetraphenylborate (NaTPB) as lipophilic additive was fabricated and investigated as Sr²⁺-selective electrode. The best performance was exhibited by the membrane having composition 8:200:4:120 (I:o-NPOE:NaTPB:PVC). The electrode exhibited a Nernstian response for strontium ion over a wide concentration range 3.98 × 10⁻⁶ to 1.0 × 10⁻¹ M with a slope of 29.0 ± 0.1 mV/decade of concentration and a detection limit of 2.82 × 10⁻⁶ M. It showed a response time of less than 10 s and could be used for at least 3 months without any divergence in potential. The proposed electrode showed a good discriminating ability towards strontium(II) ion over a wide variety of other metal ions including alkali, alkaline earth, transition, and heavy metal ions. The electrode can be used in the pH range of 2.5-10.5 and in mixtures containing up to 35% (v/v) non-aqueous content. It was used as an indicator electrode in potentiometric titration of strontium ion against EDTA.     

Nickel pyrazolyl borate complexes: Synthesis, structure and analytical application in biological and environmental samples as anion selective sensors

A [{hydrotris(3-phenyl-5-methyl-1-pyrazolyl)borate}(3-phenyl-5-methyl-pyrazole) nickel chloride] [Tp^Ph,MeNi(Cl)Pz^Ph,MeH] (I) has been synthesized and explored as ionophores for the preparation of a poly (vinyl chloride) (PVC) membrane sensor for azide and thiocyanate anions. The compounds [Tp^Ph,MeNi(N₃)Pz^Ph,MeH] (II) and [Tp^Ph,MeNi(SCN)Pz^Ph,MeH] (III) were characterized by their crystal structures and proved to be bonded as monodentate through nitrogen atom of azide and thiocyanate anion. Potentiometric investigations also indicate high affinity of this receptor for thiocyanate and azide ions. PVC based membranes of I using as hexadecyltrimethylammonium bromide (HTAB) cation discriminator and o-nitrophenyloctyl ether (o-NPOE), dibutylphthalate (DBP), acetophenone (AP) and tributylphosphate (TBP) as plasticizing solvent mediators were prepared and investigated as SCN⁻ and N₃⁻ selective sensors. The best performance was shown by the membrane of thiocyanate with composition (w/w) of (I) (7%):PVC (31%):DBP (60%):HTAB (2%). This sensor works well over a wide concentration range 5.3 × 10⁻⁷ to 1.0 × 10⁻² M with Nernstian compliance (59.2 mV decade⁻¹ of activity) within pH range 2.5-9.0 with a response time of 11 s and showed good selectivity for thiocyanate ion over a number of anions. The sensor exhibits adequate life (3 months) and could be used successfully for the determination of thiocyanate content in human urine, saliva and river water samples. While the membrane of [Tp^Ph,MeNi(Cl)Pz^Ph,MeH] ionophore with composition (I) (6%):HTAB (4%):PVC (31%):TBP (59%) showed highest sensitivity and widest linear range for azide ion. These sensors exhibit the maximum working concentration range of 8.1 × 10⁻⁶ to 1.0 × 10⁻² M with Nernstian slope of 59.3 mV decade⁻¹ of activity. It can be applied for the monitoring of the azide ions concentration in aqueous black tea and orange juice samples.     

Acyclic tetrachalcogenoether ligands tethered with bulky substituents: Their syntheses and coordination chemistry

New o-phenylene-bridged tetrachalcogenoether ligands tethered with an extremely bulky substituent, 2,4,6-tris[bis(trimethylsilyl)methyl]phenyl (Tbt) group, [TbtE(o-phenylene)Se]₂(o-phenylene) (3: E = S, 4: E = Se), were synthesized. Complexation reactions of 3 and 4 with Na₂PdCl₄ gave the corresponding dichloropalladium(II) complexes 7 and 8. X-ray structural analysis of 7 and 8 indicated that the central palladium metals are in a distorted octahedral environment, where the two inner selenium atoms and the two chlorine atoms form a square planar arrangement around the palladium metal and the two terminal chalcogen atoms weakly coordinate to the palladium center at the axial positions. The AIM calculations also supported the existence of the interaction between the palladium and the terminal chalcogen atoms in the crystalline state. On the other hand, the ⁷⁷Se NMR spectra suggested that there are no or very weak interactions between the palladium and the terminal chalcogen atoms in solution. The UV/Vis spectra of 7, 8, and related compounds imply the possibility of weak interaction between the terminal selenium atoms and the palladium center in solution.     

Synthesis,structure, and electrochemistry of pyridinecarboxamide cobalt(III) complexes; the effect of bridge substituents on the redox properties

Two series of complexes of the types trans-[Co^III(Mebpb)(amine)₂]ClO₄ {Mebpb²⁻ = N,N-bis(pyridine-2-carboxamido)-4-methylbenzene dianion, and amine = pyrrolidine (prldn) (1a), piperidine (pprdn) (2a), morpholine (mrpln) (3a), benzylamine (bzlan) (4a)}, and trans-[Co^III(cbpb)(amine)₂]X {cbpb²⁻ = N,N-bis(pyridine-2-carboxamido)-4-chlorobenzene dianion, and amine = pyrrolidine (prldn), X = PF₆ (1b), piperidine (pprdn), X = PF₆ (2b), morpholine (mrpln), X = ClO₄ (3b), benzylamine (bzlan), X = PF₆ (4b)} have been synthesized and characterized by elemental analyses, IR, UV–Vis, and ¹H NMR spectroscopy. The crystal structure of 1a has been determined by X-ray diffraction. The electrochemical behavior of these complexes, with the goal of evaluating the effect of axial ligation and equatorial substitution on the redox properties, is also reported. The reduction potential of Co^III, ranging from −0.53 V for (1a) to −0.31 V for (3a) and from −0.48 V for (1b) to −0.22 V for (3b) show a relatively good correlation with the σ-donor ability of the axial ligands. The methyl and chloro substituents of the equatorial ligand have a considerable effect on the redox potentials of the central cobalt ion and the ligand-centered redox processes.     

Novel titanocene anti-cancer drugs derived from fulvenes and titanium dichloride

Starting from 6-(p−N,N-dimethylanilinyl)fulvene (1a) or 6-(pentamethylphenyl)fulvene (1b) [1,2-di(cyclopentadienyl)-1,2-di(p−N,N-dimethylaminophenyl)ethanediyl] titanium dichloride (2a) and [1,2-di(cyclopentadienyl)-1,2-bis(pentamethylphenyl)ethanediyl] titanium dichloride (2b) and their corresponding dithiocyanato complexes (3a, 3b) were synthesized. Titanocene 2b did not show a cytotoxic effect, but when 2a was tested against pig kidney carcinoma cells (LLC-PK) or human ovarian carcinoma cells (A2780/cp70) inhibitory concentrations (IC₅₀) of 2.7 × 10⁻⁴ and 1.9 ×  10⁻⁴ M, respectively, were observed.     

Synthesis, characterization and Schlenk equilibrium studies of methylmagnesium compounds with O- and N-donor ligands - the unexpected behavior of [MgMeBr(pmdta)] (pmdta = N,N,N′,N″,N″-pentamethyldiethylenetriamine)

MgMe₂ (1) was found to react with 1,4-diazabicyclo[2.2.2]octane (dabco) in tetrahydrofuran (thf) yielding a binuclear complex [{MgMe₂(thf)}₂(μ-dabco)] (2). Furthermore, from reactions of MgMeBr with diglyme (diethylene glycol dimethyl ether), NEt₃, and tmeda (N,N,N′,N′-tetramethylethylenediamine) in etheral solvents compounds MgMeBr(L), (L = diglyme (5); NEt₃ (6); tmeda (7)) were obtained as highly air- and moisture-sensitive white powders. From a thf solution of 7 crystals of [MgMeBr(thf)(tmeda)] (8) were obtained. Reactions of MgMeBr with pmdta (N,N,N′,N″,N″-pentamethyldiethylenetriamine) in thf resulted in formation of [MgMeBr(pmdta)] (9) in nearly quantitative yield. On the other hand, the same reaction in diethyl ether gave MgMeBr(pmdta) · MgBr₂(pmdta) (10) and [{MgMe₂(pmdta)}₇{MgMeBr(pmdta)}] (11) in 24% and 2% yield, respectively, as well as [MgMe₂(pmdta)] (12) as colorless needle-like crystals in about 26% yield. The synthesized methylmagnesium compounds were characterized by microanalysis and ¹H and ¹³C NMR spectroscopy. The coordination-induced shifts of the ¹H and ¹³C nuclei of the ligands are small; the largest ones were found in the tmeda and pmdta complexes. Single-crystal X-ray diffraction analyses revealed in 2 a tetrahedral environment of the Mg atoms with a bridging dabco ligand and in 8 a trigonal-bipyramidal coordination of the Mg atom. The single-crystal X-ray diffraction analyses of [MgMe₂(pmdta)] (12) and [MgBr₂(pmdta)] (13) showed them to be monomeric with five-coordinate Mg atoms. The square-pyramidal coordination polyhedra are built up of three N and two C atoms in 12 and three N and two Br atoms in 13. The apical positions are occupied by methyl and bromo ligands, respectively. Temperature-dependent ¹H NMR spectroscopic measurements (from 27 to −80 °C) of methylmagnesium bromide complexes MgMeBr(L) (L = thf (4); diglyme (5); NEt₃ (6); tmeda (7)) in thf-d₈ solutions indicated that the deeper the temperature the more the Schlenk equilibria are shifted to the dimethylmagnesium/dibromomagnesium species. Furthermore, at −80 °C the dimethylmagnesium compounds are predominant in the solutions of Grignard compounds 4-6 whereas in the case of the tmeda complex7 the equilibrium constant was roughly estimated to be 0.25. In contrast, [MgMeBr(pmdta)] (9) in thf-d₈ revealed no dismutation into [MgMe₂(pmdta)] (12) and [MgBr₂(pmdta)] (13) even up to −100 °C. In accordance with this unexpected behavior, 1:1 mixtures of 12 and 13 were found to react in thf at room temperature yielding quantitatively the corresponding Grignard compound 9. Moreover, the structures of [MgMeBr(pmdta)] (9c), [MgMe₂(pmdta)] (12c), and [MgBr₂(pmdta)] (13c) were calculated on the DFT level of theory. The calculated structures 12c and 13c are in a good agreement with the experimentally observed structures 12 and 13. The equilibrium constant of the Schlenk equilibrium (2 9c ? 12c + 13c) was calculated to be K_gas = 2.0 × 10⁻³ (298 K) in the gas phase. Considering the solvent effects of both thf and diethyl ether using a polarized continuum model (PCM) the corresponding equilibrium constants were calculated to be K_thf = 1.2 × 10⁻³ and K_ether = 3.2 × 10⁻³ (298 K), respectively.     

Novel hydridotris(pyrazolyl)borate ruthenium(II) complexes containing the water-soluble phosphane 1,3,5-triaza-7-phosphaadamantane: Synthesis and evaluation of DNA binding properties

A series of half-sandwich ruthenium(II) complexes containing κ³(N,N,N)-hydridotris(pyrazolyl)borate (κ³(N,N,N)-Tp) and the water-soluble phosphane 1,3,5-triaza-7-phosphaadamantane (PTA) [RuX{κ³(N,N,N)-Tp}(PPh₃)_2−n(PTA)_n] (n = 2, X = Cl (1), n = 1, X = Cl (2), I (3), NCS (4), H (5)) and [Ru{κ³(N,N,N)-Tp}(PPh₃)(PTA)L][PF₆] (L = NCMe (6), PTA (7)) have been synthesized. Complexes containing 1-methyl-3,5-diaza-1-azonia-7-phosphaadamantane(m-PTA) triflate [RuCl{κ³(N,N,N)-Tp}(m-PTA)₂][CF₃SO₃]₂ (8) and [RuX{κ³(N,N,N)-Tp}(PPh₃)(m-PTA)][CF₃SO₃] (X = Cl (9), H (10)) have been obtained by treatment, respectively, of complexes 1, 2 and 5 with methyl triflate. Single crystal X-ray diffraction analysis for complexes 1, 2 and 4 have been carried out. DNA binding properties by using a mobility shift assay and antimicrobial activity of selected complexes have been evaluated.     

Copper(II) complexes of N4 tetradentate ligands with flexible alkyl spacers: Crystal structure,DNA binding and cleavage studies

Mononuclear copper(II) complexes, [Cu L1] (ClO₄)₂ (1), [Cu L2] (ClO₄)₂ (2) and [Cu L3] (ClO₄)₂ (3) with quadridentate Schiff base ligands L1 (N,N′-bis-pyridin-2-ylmethyl-butane-1,4-diimine), L2 (N,N′-bis-pyridin-2-ylmethyl-pentane-1,5-diimine) and L3 (N,N′-bis-pyridin-2-ylmethyl-hexane-1,6-diimine) have been synthesized and characterized. The crystal structure data of 1 reveals the existence of the complex in two different geometries, namely a square pyramid and a distorted octahedron, which eventually leads to the packing of the molecule into helical and anti-parallel structures respectively. Absorption titration studies with calf thymus DNA for all three complexes are suggestive of groove binding with binding constant values for 1, 2 and 3 being 2.6 ± 0.2 × 10⁴ M⁻¹, 11.5 ± 0.2 × 10⁴ M⁻¹ and 1.83 ± 0.2 × 10⁴ M⁻¹ respectively. Control cleavage experiments using pBR 322 plasmid DNA and distamycin suggest minor groove binding for these complexes. In the presence of ascorbic acid, the complexes show efficient DNA cleavage, the order of efficiency being 1 > 2 ≅ 3.     

Self-assembly and characterization of a giant metallocycle

A giant, 100-membered metallocycle 3 was prepared via coordination bond-based self-assembly from W-shaped ligand 9 and a palladium complex. Metallocycle 3 may create three topologically discrete subcavities, thus capable of binding up to three molecules of a diamide guest by hydrogen-bonding interactions. Elemental analysis, ¹H NMR, and the ESI-mass spectra, and vapor pressure osmometry (VPO) data were all consistent with the structure of 3. N,N,N′,N′-tetramethylterephthalamide G was used as a guest for the binding study, and ESI-mass spectrum clearly displayed a characteristic, intense peak at m/z 1542 (41%), attributed to the fragment [3·G₃-3CF₃SO₃]³⁺ of 1:3 (host/guest) complex. The ¹H NMR titration experiments gave association constants of 2300 ± 300 and 1200 ± 200 M⁻¹ in CDCl₃ at 25 °C for two identical outer cavities, with weak positive cooperativity (Hill coefficient h = 1.3).     

Magnetic coupling in EE and EO azido-bridged binuclear copper complexes: Synthesis,structure and magnetic studies

Four azide bridged dinuclear copper(II) complexes, [Cu₂(L^X)₂(N₃)₂](ClO₄)₂, with L^X = substituted N,N-bis[(3,5-dimethylpyrazole-1-yl)-methyl]benzylamine, [X = H (1), OMe (2), Me (3) and Cl (4)] have been synthesized, out of which complexes 1 and 2 have been characterized structurally. In Complex 1 the two bridging azide ligands have connected the two metal centers in an end-on (EO) fashion with aSP (asymmetric Square Pyramidal) geometry and showed an weak antiferromagnetic interaction (J = −3.34 cm⁻¹). On the contrary, in complex 2, the two metal centers have been connected in end-to-end (EE) fashion exhibiting moderately strong ferromagnetic interaction (J = +19.7 cm⁻¹). Cyclic voltammetric studies performed on all the four complexes show a reasonably good correlations when E_1/2 for Cu^IICu^II → Cu^IICu^III and Cu^IICu^III → Cu^IIICu^III oxidations are plotted against σ (substituent constants) with ρ = −0.182 (R² = 0.92) and −0.684 (R² = 0.99) respectively.     

Synthesis of mono- and trinuclear palladium(II) complexes via oxidative addition of a bulky hexathioether containing a disulfide bond to palladium(0)

The oxidative addition reactions of a bulky hexathioether containing a disulfide bond, TbtS(o-phen)S(o-phen)SS(o-phen)S(o-phen)STbt (1) (Tbt = 2,4,6-tris[bis(trimethylsilyl)methyl]phenyl, o-phen = o-phenylene), to a palladium(0) complex were studied. In the reaction of 1 with 3 molar amounts of [Pd(PPh₃)₄], a trinuclear palladium(II) complex, [Pd₃{S(o-phen)S}₂{(o-phen)STbt}₂(PPh₃)₂] (2), was formed via three-step palladium insertion reaction including unusual C(aryl)-S bond cleavages. On the other hand, the reaction of 1 with an equimolar amount of [Pd(PPh₃)₄] afforded mononuclear palladium(II) complex having a pseudo-octahedral structure, [Pd{S(o-phen)S(o-phen)STbt}₂] (3). The hexa-coordinated geometry for the palladium center in 3 was confirmed by the atoms in molecule (AIM) analysis, which revealed the presence of the bond critical points between the central Pd atom and the S atoms at the axial positions. In contrast to the bulky system, the reaction of Ph-substituted hexathioether, PhS(o-phen)S(o-phen)SS(o-phen)S(o-phen)SPh (4), with an equimolar amount of [Pd(PPh₃)₄] gave a palladium(II) complex having square-planar structure, [Pd{S(o-phen)S(o-phen)SPh}₂] (5). Theoretical calculations revealed that there is no remarkable difference among the energies of isomers of [Pd{S(o-phen)SPh}₂], 6a-syn, 6a-anti, 6b-syn, and 6b-anti. This result suggests that a reason for the preference of the trans-anti-conformation in 3 is the steric repulsion between the bulky Tbt groups, and that of the cis-syn-conformations in 5 and 6 is the intermolecular interactions.     

Synthesis of 2-(N-arylimino-κN-methyl)pyrrolide-κN complexes of nickel

2-(N-aryliminomethyl)pyrrole precursors (2,6-R₂-C₆H₃-NCH-2-C₄H₃NH) (R = Me, IH; R = ⁱPr, IIH) were prepared and transformed into their corresponding sodium salts (Na⁺I⁻ and Na⁺II⁻) by treatment with NaH. Both salts readily react with [NiBr₂(DME)] (DME = 1,2-dimethoxyethane) to give the respective bis{2-(N-arylimino-κN-methyl)pyrrolide-κN}nickel(II) complexes (1, 2) in almost quantitative yields. The oxidative addition of IH to [Ni(COD)₂] (COD = 1,5-cyclooctadiene) results in the formation of 3, which is a mono(iminomethylpyrrolide)-η³-(cyclic-allyl)-type organonickel(II) complex. The crystal structure of compound 1 has been established by X-ray diffraction studies.     

Synthesis, photophysical and electrophosphorescent properties of mononuclear Pt(II) complexes with arylamine functionalized cyclometalating ligands

Four cyclometalated Pt(II) complexes, i.e., [(L²)PtCl] (1b), [(L³)PtCl] (1c), [(L²)PtCCC₆H₅] (2b) and [(L³)PtCCC₆H₅] (2c) (HL² = 4-[p-(N-butyl-N-phenyl)anilino]-6-phenyl-2,2′-bipyridine and HL³ = 4-[p-(N,N′-dibutyl-N′-phenyl)phenylene-diamino]-phenyl-6-phenyl-2,2′-bipyridine), have been synthesized and verified by ¹H NMR, ¹³C NMR and X-ray crystallography. Unlike previously reported complexes [(L¹)PtCl] (1a) and [(L¹)PtCCC₆H₅] (2a) (HL¹ = 4,6-diphenyl-2,2′-bipyridine), intense and continuous absorption bands in the region of 300-500 nm with strong metal-to-ligand charge transfer (¹MLCT) (dπ(Pt) → π^∗(L)) transitions (ε ∼ 2 × 10⁴ dm³ mol⁻¹ cm⁻¹) at 449-467 nm were observed in the UV-Vis absorption spectra of complexes 1b, 1c, 2b and 2c. Meanwhile, with the introduction of electron-donating arylamino groups in the ligands of 1a and 2a, complexes 1b and 2b display stronger phosphorescence in CH₂Cl₂ solutions at room temperature with bathochromically shifted emission maxima at 595 and 600 nm, relatively higher quantum yields of 0.11 and 0.26, and much longer lifetimes of 8.4 and 4.5 μs, respectively. An electrochromic film of 1b-based polymer was obtained on Pt or ITO electrode surface, which suggests an efficient oxidative polymerization behavior. An orange multilayer organic light-emitting diode with 1b as phosphorescent dopant was fabricated, achieving a maximum current efficiency of 11.3 cd A⁻¹ and a maximum external efficiency of 5.7%. The luminescent properties of complexes 1c and 2c are dependent on pH value and solvent polarity, which is attributed to the protonation of arylamino units in the C^N^N cyclometalating ligands.     

Two-stage formation of chloro (N-o-chlorobenzamido-meso-tetraphenylporphyrinato) zinc(II) methylene chloride solvate: Zn(N-NHCO(o-Cl)C6H4-tpp)Cl · CH2Cl2

The coordinating properties of N-o-chlorobenzamido-meso-tetraphenylporphyrin (N-NHCO(o-Cl)C₆H₄-Htpp; 11) have been investigated for the Zn²⁺ ion. Insertion of Zn results in the formation of the zinc complex Zn(N-NCO(o-Cl)C₆H₄-tpp)(MeOH) · MeOH (12 · MeOH). The diamagnetic 12 · MeOH can be transformed into the diamagnetic Zn(N-NHCO(o-Cl)C₆H₄-tpp)Cl · CH₂Cl₂ (13 · CH₂Cl₂) in a reaction with aqueous hydrogen chloride (2%). X-ray structures for 12 · MeOH and 13 · CH₂Cl₂ have been determined. The coordination sphere around the Zn²⁺ ion in 12 · MeOH is a distorted trigonal bipyramid with N(2), N(4) and O(2) lying in the equatorial plane, whereas for the Zn²⁺ ion in 13 · CH₂Cl₂, it is a square-based pyramid in which the apical site is occupied by the Cl(1) atom.     

Synthesis and characterization of N-(2-pyridyl)benzamide-based nickel complexes and their activity for ethylene oligomerization

A series of N-(2-pyridyl)benzamides (1)-(11) and their nickel complexes, [N-(2-pyridyl)benzamide]dinickel(II) di-μ-bromide dibromide (12)-(16) and (aryl)[N-(2-pyridyl)benzamido](triphenylphosphine)nickel(II) (17)-(24), were synthesized and characterized. The single-crystal X-ray analysis revealed that 12 and 14 are binuclear nickel complexes bridged by bromine atoms and each nickel atom adopts a distorted trigonal bipyramidal geometry. The key feature of the complexes 17, 19 and 23 is each has a six-membered nickel chelate ring including a deprotonated secondary nitrogen atom and an O-donor atom. The nickel complexes show moderate to high catalytic activity for ethylene oligomerization with methylaluminoxane (MAO) as cocatalyst. The activity of 12-16/MAO systems is up to 3.3 × 10⁴ g mol⁻¹ h⁻¹ whereas for 17-24/MAO systems it is up to 4.94 × 10⁵ g mol⁻¹ atm⁻¹ h⁻¹. The influence of Al/Ni molar ratio, reaction temperature, reaction period and PPh₃/Ni molar ratio on catalytic activity was investigated.