In this numerical study, laminar flow of water nanofluid/GNP–SDBS (graphene nanoplatelet–sodium dodecylbenzene sulfonate) for 0–0.1% solid nanoparticles mass fraction was investigated for Reynolds numbers of 50–1000 in 3D space via finite volume method. In the newly proposed microchannel design, the cooling fluid is moving in countercurrent in the upper and lower layers of the microchannels, and there are cavities and sinusoidal routes on the solid walls of the microchannel, and the presence of rectangular ribs on the flow centerline along the fluid path enhances mixing for cooling fluid and creates better heat transfer for warm surfaces. The results of this study show that this special design of the microchannel can have a substantial increase in Nusselt number and heat transfer so that in the considered geometry by adding solid nanoparticles mass fraction it is possible to increase average Nusselt number for each Reynolds number by approximately 20%. Also, the mixing of the fluid because of formation of secondary flows has a strong effect on making the temperature distribution uniform in the cooling fluid and solid bed (wall) of the microchannel, especially in the lower layer. The upper layer of the microchannel always has a lower temperature due to indirect contact with heat flux compared with the lower layer. In this study, by increasing Reynolds number and mass fraction of solid nanoparticles the Nusselt number is increased and heat resistance of the lower wall of the microchannel is reduced. Based on the investigation of flow field and heat transfer, the use of the proposed design of the microchannel is recommended for Reynolds number less than 300.
相似文献Turbulent flow characteristics and heat transfer applications of a twisted heat exchanger with 3-lobed cross section along with Y-tape insert are numerically studied. The working fluids for the simulations are pure water and water–Al2O3 nanofluid using two-phase mixture model. The study is carried out for various nanofluid volume fractions of 0.01, 0.02 and 0.03 with Reynolds number in the range of 5000–20,000. The effect of nanoparticles in heat transfer augmentation for smooth and lobed tubes is discussed based on presenting the highest thermal performance, which is a relation between heat transfer rate and pressure loss. Results show that implementing the twisted tube with Y-tape insert enhances the heat transfer more than the twisted tube. Relative Nusselt numbers for twisted tubes decrease with Reynolds number in comparison with the plain tube. Turbulent intensity, swirl number and tangential velocity of twisted tube with insert are higher than empty twisted tube indicating that inserting the Y-tape intensifies the turbulence and disturbs the fluid flow further. On the other hand, although the twisted tube increases the pressure drop more than plain tube, the case with Y-tape drastically increases the friction factor. So, the thermal performance of twisted tube with insert is lower than empty twisted tube. Adding nanoparticles to the base fluid has different influence on the investigated cases. It augments the relative Nusselt number inside plain tube and empty twisted tube with slight increment in friction factor. Increasing the nanoparticles concentration enhances the heat transfer rates for these cases while it does not increase the relative Nusselt number inside twisted tube with Y-tape insert at high Reynolds number and nanoparticle concentration. Moreover, it can be found that twisted tube with or without Y-tape insert is more efficient at low Reynolds number in comparison with the plain tube.
相似文献In this study, heat transfer and entropy generation were investigated in a microchannel containing FMWNT/water nanofluids given the slip condition. The main focus was on utilizing injection technique in the presence of the magnetic field. The injection from the upper high-temperature wall was incorporated into the flow field. Injection at high Reynolds number causes vortex formation, which ultimately reduces local heat transfer in the adjacent injection zone. By applying the magnetic field, the vortex intensity as well as boundary layer thickness was diminished which in turn improved the heat transfer. Based on numerical results, at higher nanoparticle volume fraction, the effect of the magnetic field on heat transfer enhancement was amplified. Moreover, at higher Reynolds numbers, the magnetic field efficacy is more obvious. The highest heat transfer occurred at the highest values of the Hartmann and Reynolds numbers and eventually the nanoparticle volume fraction. Owing to applying the magnetic field on the injectable microchannel containing nanofluid, heat transfer improvement can reach up to 79%. From the second law prospective, the entropy generation intensified by 82.8%.
相似文献Numerical studies of laminar forced convective heat transfer and fluid flow in a 2D louvered microchannel with Al2O3/water nanofluids are performed by the lattice Boltzmann method (LBM). Eight louvers are arranged in tandem within the single-pass microchannel. The Reynolds number based on channel hydraulic diameter and bulk mean velocity ranges from 100 to 400, where the Al2O3 fraction varies from 0 to 4%. A double distribution function approach is adopted for modeling fluid flow and heat transfer. Code validations are performed by comparing the streamwise Nusselt number (Nu) profiles and Fanning friction factors of the present LBM and those of the analytical solutions. Good agreements are obtained. Simulated results show that the louver microstructure can disturb the core flow and guide coolant toward the heated walls, thus enhancing the heat transfer significantly. Furthermore, the addition of nanoparticles in microchannels can also augment the heat transfer, but it creates an unnoticeable pressure loss. With both the louver microstructure and nanofluid, a maximum overall Nu enhancement of 7.06 is found relative to that of the fully developed smooth channel.
相似文献Nanofluid and coiled tubes have been employed as two passive methods for enhancing the heat transfer. In the present study, the turbulent flow of CuO–water nanofluid in helical and conical coiled tubes was numerically investigated with constant wall temperature through mixture model. The thermophysical properties of base fluid (water) were considered as temperature-dependent functions, while Brownian effects were adopted in thermal conductivity and dynamic viscosity of nanofluid. Simulation results were validated using experimental data for heat transfer coefficient and pressure drop in helical coiled tube for different Reynolds numbers. Four different geometries were simulated and compared. The first one was a conical coiled tube; the others were helical coiled tubes whose coil diameters were minimum, maximum, and median of the conical coiled tube pitch coil diameter. The velocity profiles indicated stronger secondary flow in conical coiled tube at a specified Dean number. The obtained results also showed higher heat transfer enhancement in the conical coiled tube in comparison with helical coiled tube with the same average pitch coil diameter. Moreover, the nanoparticle-induced heat transfer enhancement was more effective in conical coiled tube.
相似文献A numerical analysis was carried out of mixed convection heat transfer for a laminar flow in a rectangular inclined microchannel totally filled with a water/Al2O3 nanofluid. The governing conservation equations are translated into a dimensionless form using the thermal single relaxation time and they modify the lattice Boltzmann method with double distribution functions. The viscous dissipation effects are adapted to the energy equation. The effects of nanoparticle volume fractions ? (0?≤???≤?0.04) and inclination angles γ (0°?≤?γ?≤?60°) on the flow of the nanofluid and the heat transfer are investigated. The obtained results are presented in terms of streamlines, isotherms, slip velocity, wall temperature and Nusselt number. The results show that the higher values of the volume fraction of Al2O3 and the large values of inclination angles improve the heat transfer rate.
相似文献The present study aims to enhance the hydrothermal performance of a porous sinusoidal double-layered heat sink using nanofluid. The optimum thickness of metal foam (nickel) for different Reynolds numbers ranging from 10 to 100 for the laminar regime and Darcy numbers ranging from 10?4 to 10?2 is obtained. At the optimum porous thicknesses, nanofluid (silver–water) with three volume fractions of nanoparticles equal to 2, 3, and 4% is employed to enhance the heat sink thermal performance. Darcy–Brinkman–Forchheimer model and the local thermal non-equilibrium model or two equations method are employed to model the momentum equation and energy equations in the porous region, respectively. It was found that in the cases of Darcy numbers 10?4, 10?3, and 10?2 the dimensionless optimum porous thicknesses are 0.8, 0.8, and 0.2, respectively. It was also obtained that the maximum PEC number is 2.12 and it corresponds to the case with Darcy number 10?2, Reynolds number 40, and volume fraction of nanoparticles 0.04. The validity of local thermal equilibrium (LTE) assumption was investigated, and it was found that increasing the Darcy number which results in an enhancement in porous particle diameter leads to some errors in results, under LTE condition.
相似文献In the present study, heat transfer and fluid flow of a pseudo-plastic non-Newtonian nanofluid over permeable surface has been solved in the presence of injection and suction. Similarity solution method is utilized to convert the governing partial differential equations into ordinary differential equations, which then is solved numerically using Runge–Kutta–Fehlberg fourth–fifth order (RKF45) method. The Cu, CuO, TiO2 and Al2O3 nanoparticles are considered in this study along with sodium carboxymethyl cellulose (CMC)/water as base fluid. Validation has been done with former numerical results. The influence of power-law index, volume fraction of nanoparticles, nanoparticles type and permeability parameter on nanofluid flow and heat transfer was investigated. The results of the study illustrated that the flow and heat transfer of non-Newtonian nanofluid in the presence of suction and injection has different behaviors. For injection and the impermeable plate, the non-Newtonian nanofluid shows a better heat transfer performance compared to Newtonian nanofluid. However, changing the type of nanoparticles has a more intense influence on heat transfer process during suction. It was also observed that in injection, contrary to the other two cases, the usage of non-Newtonian nanofluid can decrease heat transfer in all cases.
相似文献In this paper, we analyze the effect of heat transfer on the flow of tangent hyperbolic nanofluid in a ciliated tube (fallopian tube where embryo in blood make the development). This study will be beneficial for the researchers and medical experts in the field of embryology. The nanoparticles are beneficial to remove the cysts from the fallopian tube where development of embryo takes place. To resolves the ciliary flow problems, medical doctors use nanoparticles (drug delivery) that may create a temperature gradient. The heat transfer helps to optimize the energy for which the entropy generation is reduced. Therefore, in this research we discuss the heat transfer effect on tangent hyperbolic nanofluid and entropy generation due to ciliary movement. The governing partial differential equations are solved by HPM and software MATHEMATICA?. Effect of viscoelastic parameter, nanoparticles, cilia length and Brinkman number on the velocity, temperature and entropy generation has been illustrated with the help of graphs. Graphical results show that thermal conductivity of fluid increases by adding nanoparticles. The entropy generation due to nanoparticles will decrease the viscosity near the tube wall and blood through tube will flow with normal pressure.
相似文献Development of various electronic devices demands to create effective cooling complexes. The present paper deals with computational analysis of mixed convection cooling of heat-conducting and heat-generating element located inside an alumina–water nanofluid enclosure with upper moving wall. Usage of upper moving wall, nanofluid and cooling vertical walls allows to create the effective cooling process. Analysis has been performed numerically using the Oberbeck–Boussinesq equations. The effects of nanoparticles concentration, heat source location and upper wall velocity on flow structures, heat exchange and entropy generation have been investigated. It has been ascertained that effective cooling of the heated element occurs for high Reynolds number and central position of the heat-generating element.
相似文献Forced convection hybrid nanofluid flow over a backward-facing step under a non-uniform magnetic field is numerically studied using a finite volume method. The external magnetic source is placed in the step edge. The study is performed for a range of nanoparticles volume fraction, φ, from 0 to 2%, Hartmann number, Ha, from 0 to 50, and Reynolds number, Re, from 100 to 300. Results show that the reattachment length reduces by increasing volume fraction of nanoparticles and by decreasing Reynolds number. The recirculation bubble weakens and the conductive heat transfer mode growth by increasing Hartmann number at weak magnetic field intensity. It totally disappears at high Hartmann number when the convective mode dominates. The average Nusselt number increases by increasing volume fraction of nanoparticles and varies with the Hartmann number. The effects of Lorentz force and hybrid nanoparticles on the heat transfer enhancement rates are strongly linked with volume fraction of nanoparticles and Hartmann and Reynolds numbers.
相似文献In the present study, the exact solution of a nanofluid flow and mixed convection within a vertical cylindrical annulus with suction/injection, which is adjacent to the radial magnetic field, is presented with regard to the motion of cylinders’ walls. The impact of Brownian motion and shape factor on the thermal state of CuO–water nanofluid is also considered. The influence of such parameters as Hartmann number, mixed convection parameter, suction/injection, volume fraction of nanoparticles and motion of cylinders’ walls on flow and heat transfer is probed. The results show that the shape of the nanoparticles could change the thermal behavior of the nanofluid and when the nanoparticles are used in the shape of a platelet, the highest Nusselt number is obtained (about 2.5% increasement of Nusselt number on internal cylinders’ wall comparison to spherical shape). The results shed light on the fact that if, for example, the external cylinder is stationary and the internal cylinder moves in the direction of z axis, the maximum and minimum heat transfer take place on the walls of internal and external cylinders, respectively (for η?=?300, about 15% increasement of Nusselt number on internal cylinders’ wall). Furthermore, the enhancement of radius ratio between two cylinders increases the rate of heat transfer and decreases the shear stress on the internal cylinder’s wall.
相似文献Entropy generation analysis for the Cu–water nanofluid flow through a heat exchanger tube equipped with perforated conical rings is numerically investigated. Frictional and thermal entropy generation rates are defined as functions of velocity and temperature gradients. Governing equations are solved by using finite volume method, and Reynolds number is in the range of 5000–15,000. The effects of geometrical and physical parameters such as Reynolds number, number of holes and nanoparticles volume fraction on the thermal and viscous entropy generation rates and Bejan number are investigated. The results indicate that the thermal irreversibility is dominant in most part of the tube. But it decreases with increasing the nanoparticle volume fraction. Frictional entropy generation reduces with increasing the number of holes from 4 to 10. This is because of stronger velocity gradient near the perforated holes. Bejan number decreases with augment of Reynolds number.
相似文献This study aimed to investigate the increase in heat transfer in the indirect heater at a city gate station (CGS) with the addition of copper oxide (CuO) nanoparticles to water–ethylene glycol base fluids. Indirect heaters are typically used at CGSs to raise the heat transfer coefficient of output gas flow from ? 5 to 15 °C. Moreover, manufacturing laboratory equipment in the presence of water–ethylene glycol base fluid and the nanoparticle in volume fractions of 0.05, 0.1, 0.2, and 0.3 at a temperature of 40–70 °C was discussed using dimensional simulation and analysis. The physical properties of the base fluid and nanofluid were measured using precise devices. Heat transfer tests for the base and nanofluid, as well as replacing of the air by gas, were conducted in a simulated and developed device. According to the obtained results with respect to the changes in convection and conduction heat transfer, enhancement of temperature difference at a rate of 36% was observed in the indirect heater with nanoparticle volume concentration of 0.2% at a temperature of 70 °C. Moreover, the Nusselt number showed a relatively good agreement with theoretical discussions.
相似文献The effect of a magnetic field on heat and fluid flow of ferrofluid in a helical tube is studied numerically. The helical tube is under constant wall temperature boundary condition. Parametric studies are done to investigate the effects of different factors such as the magnetic field gradient value and Reynolds number on heat transfer rate and pressure drop. Results indicate that the magnetic field increases the Nusselt number by about 40%. At high magnetic gradient value, Nusselt number and friction factor rise slightly, while at low magnetic gradient value, the increment of Nusselt number is considerable. Furthermore, the growth of wall shear stress on tube wall results in lower thermal–hydraulic performance at the high magnetic gradient value. There is an optimum case for thermal–hydraulic performance which results in most top performance of helical tube in the presence of the magnetic field.
相似文献Pulsating heat pipe (PHP) is a type of wickless heat pipe that has a simple structure and an outstanding thermal performance. Nanofluid is a type of fluid in which nanoparticles are dispersed in a base fluid and have generally a better thermal conductivity in comparison with its base fluid. In this article, the performance of a nanofluid PHP is investigated. Graphene/water nanofluid with a concentration of 1 mg mL?1 and TiO2 (titania)/water nanofluid with a concentration of 10 mg mL?1 are used as the working fluids. To simultaneously investigate the thermal performance and flow regimes in the PHP, a one-turn copper PHP with a Pyrex glass attached to its adiabatic section is used. A one-turn Pyrex PHP is also used to fully visualize flow patterns in the PHP. Our results show that the material for the fabrication of a PHP and temperature of the working fluid are the most important parameters that affect the stability of a nanofluid in the PHP. The more stable nanofluid keeps its stability in the cupper PHP, while the less stable nanofluid starts to aggregate right after the injection to the cupper PHP. The more stable nanofluid has a better thermal performance than water, while the less stable nanofluid has a worse thermal performance than water. In the case of flow regimes, no significant differences are observed between the nanofluid PHP and the water PHP which is different from the previous observations. These results can help researchers to choose the best working fluid for PHPs.
相似文献