Critical comparison of ICP-OES, XRF and fluorine volatilization-FTIR spectrometry for the reliable determination of the silicon main constituent in ceramic materials

For the optimization of preparation processes for ceramic powders and compacts by pyrolysis of inorganic polymers, the intermediate and final products have to be monitored by in-situ analysis (in its original place) for main, subsidiary and trace components. In the determination of silicon in Si-N-C- based ceramic samples by ICP-OES after pressurized decomposition at temperatures between 220°–250°C too low concentrations of Si were found. Completely independent analytical procedures were applied to trace systematic errors, i.e. XRF after decomposition of the sample in a metaborate/boric acid melt and FTIR-spectrometry after reaction of the sample with fluorine. The low recoveries of Si were found to be due to losses, which amount up to 25% depending on the temperature and time applied for the pressurized decomposition. With the latter two procedures Si can be determined in the %-range with a relative standard deviation of 0.4% and 0.2%, respectively.     

电感耦合等离子体原子发射光谱(ICP-AES)法测定胡蜂酒中无机元素

采用电感耦合等离子体原子发射光谱法测定胡蜂酒中20种无机元素,建立无机元素对照指纹图谱,对重金属元素进行风险评估。结果表明,胡蜂酒中无机元素种类丰富,其中P、K、Na元素占测定总元素的96.14%。有害元素Pb、Cd、As、Hg、Cu含量符合国家药典标准要求,Cu的靶标危险系数(THQ)为1.00×10^-2,THQ<1说明摄入的重金属对人体健康造成的影响不明显。不同产区胡蜂酒金属元素含量存在差异,根据金属元素图谱得出元素含量按原子序数顺序出现相似的分布态势。结果表明,胡蜂酒中含有丰富的金属元素,很多为营养微量元素,有害元素(Pb、Cd、As、Hg、Cu)含量符合药典要求,从金属元素方面单一来看,饮用胡蜂酒没有明显的健康风险。胡蜂酒无机元素指纹图谱可为胡蜂酒的鉴别提供一定的的参考依据。     

Determination of Inorganic and Total Arsenic in Wines by Hydride Generation Atomic Absorption Spectrometry

A method is described for the determination of inorganic arsenic species and total arsenic in wines by means of hydride generation atomic absorption spectrometry (HGAAS). Simple ethanol evaporation is the only pretreatment procedure proposed for wine samples prior to direct measurement of inorganic arsenic (AsIII) and As(V) species by HGAAS. The total arsenic content is determined after microwave digestion of the wine samples. The optimal parameters for the microwave digestion procedure and the next HGAAS measurement of arsenic are established. The detection limits achieved are 0.1µgL^–1 for inorganic and total arsenic determination. The relative standard deviation for both procedures and for ten independent determinations varied between 8 and 15% for arsenic species in the range of 1–30µgL^–1. The accuracy of the procedure for total arsenic determination was proved by comparative analysis using electrothermal atomic absorption spectrometry.     

蜂花粉的营养价值研究

蜂花粉经微波消解完全后,通过ICP-OES测定了其多种微量元素的含量.结果表明,蜂花粉中含有丰富的微量元素,平均含量以钙、铁、镁居多,分别为1 118.110、782.135、82.351 mg/kg;其它被检测的微量元素均有一定的含量,且均在人体健康适用范围之内;有毒害性的元素铅、镉含量极微.由此可见,蜂花粉因其含量...     

Ein Beitrag zur ?nologie und ?kologie von Selen

Summary Little is known about selenium contents in alcoholic beverages, especially in wine, because no reliable determination method was available so far. A procedure for the detection of selenium in the pg- and low ng-range was developed, which uses the hydride-generation-condensation-AAS (HGC-AAS). Selenium contents in 103 German wines of the year vintages 1950 until 1985 were determined. In mean they range between 0.29 and 0.79 g/l Se and show a certain dependence from the geological soil formation and the wine species. Corresponding vineyard soils from Ingelheim (Rheinhessen, FRG) contain 0.18–0.44 mg/kg Se, mean 0.24 mg/kg Se, 10% of it is available for plants. The distribution of selenium in grape berries shows selenium-rich seeds and — with red wine species — selenium-rich skins. Higher selenium contents by contamination were observed near an industrial location. The behaviour of selenium in the vegetation cycle is pursued. The selenium depletion during fermentation may amount to 60%. All results are summarized in the so-called trace element vinogram. Selenium hence is a regular and natural constituent part of wine.

---

---

Herrn Prof. Dr. R. Neeb zum 60. Geburtstag gewidmet     

Trace determination of molybdenum and vanadium in natural waters by means of atomic spectroscopy (AAS, ICP-OES) after preconcentration

Conclusions Mo and V are abundant trace elements in the environment and of great significance for many organisms [1]. Their accurate and precise determination in natural waters by means of AAS and ICP-OES often requires a separation and/or a pre-concentration step. For the reliable and simple separation of Mo and V in the ng/l- to g/l-range, the co-precipitation on Cell-Fe and Cell-In can be applied with good reproducibility. By coupling with atomic spectroscopy, analytical procedures result for ultratrace determination of Mo and V, even in complex water matrices or biological fluids (e.g., urine).

---

Atomspektroskopische Bestimmung (AAS, ICP-OES) von Molybdän- und Vanadium-Spuren in natürlichen Wässern nach Voranreicherung

     

Sensitive Method for Trace Determination of Mercury in Wines Using Electrothermal Atomic Absorption Spectrometry

An accurate, simple and precise method for total mercury determination in wines is described. Liquid/liquid extraction of inorganic and organic mercury species directly from untreated wine samples is recommended as a preconcentration procedure prior to determination by electrothermal atomic absorption spectrometry (ETAAS). Ammonium pyrrolidinedithiocarbamate was used as complexation agent. The optimal instrumental parameters for ETAAS measurement of mercury species extracted are proposed. The detection limit for total mercury determination is 0.2µgL^–1. The relative standard deviation is 15–22% for mercury in wine in the range of 0.2–5µgL^–1. The proposed procedure has been successfully applied to the determination of mercury in bottled wines in Bulgaria and Macedonia.     

Determination of trace elements in small water samples by total reflexion X-ray fluorescence (TXRF) and by neutron activation analysis (NAA)

The problems encountered in the determination of trace elements in small sample volumes of the order of 1 to 10 l (e.g. in droplets of water) are discussed. Total reflexion X-ray fluorescence (TXRF) and neutron activation analysis (NAA) are applied for the determination of Na, Mg, K, Ca, Mn, Fe, Co, and Cu in concentrations of 0.01 to 10 mg/L in 1 to 10 L of water. The applied methods are described, the results are discussed and the advantages of TXRF are brought forward.     

A kinetic study of trace element leachability from abandoned-mine-polluted soil treated with SS-MSW compost and red mud. Comparison with results from sequential extraction

The effect of adding treated red mud, a by-product of alumina production, to soil polluted by an abandoned mine and characterised by high concentrations of heavy metals, relatively low reaction grade, and low organic carbon content, was investigated. Also studied was addition of both red mud and compost (produced from source-separated municipal solid waste)—the synergistic action of red mud and compost could be exploited to achieve both metal trapping and an increase in organic carbon content. Leaching batch tests were performed on four different systems: soil, soil and treated red mud, soil and compost, soil and compost plus treated red mud. Dilute sulfuric acid and EDTA solution (liquid/solid ratio 10:1) were used in the tests—sulfuric acid to mimic acid rain and EDTA in accordance with general methods for estimating plant-available metals. Sequential extraction was also applied to the same samples. The use of relatively non-specific extractant reagents in the leaching tests led to a kinetic approach (already proposed in literature), because measurements of trace elements extracted at equilibrium cannot be related to their speciation. Comparison of information obtainable by the kinetic approach to evaluation of data from leaching tests with results from sequential extraction enabled evaluation whether the kinetic fractionation method, a relatively rapid and simple procedure, furnishes adequate information about the mobility and bioavailability of trace elements. Especially interesting results were obtained for Mn, Zn, and Ni, present in large amounts in the soil studied—their leachability was significantly reduced by addition of red mud and compost, suggesting interesting perspectives in soil-remediation activity.     

Performance for PAN-3 chelate fiber for adsorbing and separating trace uranium—determination by ICP-OES

An ICP-OES method is established for polyacrylamidoxime-carboxylic acid chelate fiber (PAN-3) adsorbing and separating trace uranium in waste water. The conditions for quantitative enrichment and desorption uranyl ions are investigated. The stability and the reuse performance of the chelate fiber are discussed. The interference of co-existent ions on uranyl ions as well as the analyses of samples are performed with satisfactory results. The lowest concentration of uranium determined by ICP-OES is 5 g/l, its RSD is 2.6%.     

益本昌药酒的研制、临床应用与微量元素测定

介绍了益本昌药酒的研制,临床应用和疗效,测定并探讨了该药酒中所含微量元素及其与心脑血管病等的关系。结果表明,该药酒含有或富含人体必需宏量和微量元素钾,镁,钙,磷,钠,镍,钴,钒,锰,铜,铁,钴,锌,硒等。     

Bestimmung von Spurenelementen in Flu?wasser mit Hilfe der Voltammetrie

Zusammenfassung Bei der Bestimmung von Spurenelementen in Flußwasser durch Voltammetrie treten Störungen auf, die überwiegend von organischen Verunreinigungen verursacht werden. Die Einflüsse dieser Verunreinigungen können durch oxidative UV-Photolyse beseitigt werden.Im Anschluß an die Bestrahlung der Proben konnten in filtriertem Rheinwasser Zn, Cd, Pb, Cu, Ni, Co, Tl und mit Einschränkungen auch Mn voltammetrisch bestimmt werden. Die Konzentrationen an Bi und Se lagen unterhalb der Nachweisgrenze. Die Nachweisgrenzen für die genannten Elemente in Flußwasser bewegten sich in der Größenordnung zwischen 0,1 und 1 g/l. Vergleichsbestimmungen mit Hilfe der flammenlosen AAS (Graphitrohrküvette) ergaben gute Übereinstimmung für die Elemente Cu, Zn und Mn, während die Konzentrationen der anderen Elemente unterhalb der Nachweisgrenze der AAS lagen.Die Komplexierungskapazität des Rheinwassers für Zn, Cd, Pb und Cu wurde durch voltammetrische Titration ermittelt. Sie lag zwischen 5,0 und 0,7 g/l und nahm in der Reihenfolge Cu > Zn > Pb > Cd ab.

---

Determination of trace elements in river water by means of voltammetry

Summary The determination of trace elements in river water by voltammetry is disturbed by the presence of organic substances. The influence of these substances can be eliminated by oxidative UV-photolysis.After UV irradiation the following elements were determined in Rhine water by voltammetry: Zn, Cd, Pb, Cu, Ni, Co, Tl and — with reservations — Mn. The concentrations of Bi and Se were below the detection limits. The detection limits in river water for the elements mentioned were determined and found to be between 0.1 and 1 g/l. Comparative determinations by AAS (graphite tube) showed good agreement for Cu, Zn and Mn, whereas the concentrations of the other elements were below the detection limits of AAS.The complexing capacity of Rhine water for Zn, Cd, Pb and Cu was determined by voltammetric titration. It decreased in the order Cu > Zn > Pb > Cd and was between 5.0 and 0.7 g/l.

     

Ammonium determination in wine by gas phase molecular absorption spectrometry

A procedure for the determination of ammonium is described, based on its transformation into ammonia gas and subsequent measurement by UV-visible molecular absorption spectrometry at 194 nm. Two different procedures for generating the ammonia are proposed, using NaOH solution and solid NaOH, respectively. After generation conditions for both procedures had been optimized, better sensitivity was observed with solid NaOH. In these conditions, the method showed two ranges of linear response: from 1 to 100 g and from 100 to 400 g of ammonium. Finally, we determined ammonium in wine samples. Preliminary studies indicated that the only observable interfering species was ethanol, which could be eliminated by subjecting the sample to vacuum evaporation until nearly dry. This process also increased the sensitivity of the method by as much as ten times. The values obtained from three different wine samples yielded results within the range of the concentration obtained by other authors. The recovery of ammonium added to the wine samples was around 95%.     

3D-SIMS analysis of ultra high purity molybdenum and tungsten: a characterisation of different manufacturing techniques and products

Applying a recently developed three dimensional SIMS imaging technique major differences in the distribution of trace elements in ultra high purity Mo and W have been found. In the electron beam melted material severe grain boundary segregation of trace elements have occurred whereas in the hot pressed material trace elements have been present as precipitates with a size of 5–15 m. Guided by the results of the 3D-SIMS images and the advantages of the sintering process a material with homogeneous distribution of trace elements has been developed and characterised. To test the applicability for the microelectronics industry, sputtering targets have been manufactured out of this new material and layers with a thickness of 350 nm have been sputterdeposited on silicon. The quality of these layers, with respect to particle emission and the distribution of trace elements, was evaluated by EPMA and 3D-SIMS imaging. Further improvement of the sintering process led to a material with a completely homogeneous distribution of C, H, N, O and S to minimise the outgassing and diffusion of impurities.Abbreviations BSE Back scattered electron - EPMA Electron probe micro analysis - GAAS Graphite furnace atomic absorption spectrometry - GDMS Glow discharge mass spectrometry - ICP-AES Inductively coupled plasma atomic emission spectrometry - ICP-MS Inductively coupled plasma mass spectrometry - SIMS Secondary ion mass spectrometry - ULSI Ultra large scale integration     

Determination of rare earths and other trace elements in samples of Antarctica by neutron activation analysis

The concentrations of REE and other trace elements have been determined in samples of Antarctica by Instrumental Neutron Activation Analysis (INAA). The samples were collected from the West Lake area near Great Wall Station. The samples include sediment, residual plants, rock and soil taken from the bottom of the lake to 3.4 m deep. The amounts of samples were very rare. In order to get more information, reactor NAA using both short and long irradiations with K₀ standardization has been adopted. Nine rare-earth elements (REE) namely La, Ce, Nd, Sm, Eu, Tb, Dy, Yb, and Lu as well as other trace elements (As, Au, Ba, Br, Co, Cr, Hf, Sc, Se, Th, V, Zn) have been determined. The concentrations and distribution patterns of REE in the samples have been given.     

Platinum-Group Element Distribution in Some Ore Deposits: Results of EPMA and Micro-PIXE Analyses

The distribution of platinum-group elements (PGE) in the Main Sulfide Zone of the Great Dyke of Zimbabwe, in the arsenide ores of Vammala and Kylmäkoski mines in Finland, and in the chromite-Ni arsenide ores from the Ronda and Beni Bousera massifs (Spain and Morocco) has been studied by means of different optical and microanalytical techniques. The results show a bimodal distribution of PGE in the ores from the Great Dyke and the Vammala and Kylmäkoski mines where Pd, Pt and, to lesser extent, Rh occur both as discrete platinum-group minerals and in solid solution in sulfides, arsenides and sulfarsenides. In the ores from Ronda and Beni Bousera, platinum-group elements occur only in solid solution in arsenides and sulfarsenides.Trace electron probe (EPMA) and micro-PIXE analyses of Pd in sulfides, arsenides and sulfarsenides produce comparable results at concentration levels well above their limit of detection (LOD). These are 27–29ppm by EMPA and 2.5–7ppm by micro-PIXE. Whereas trace EPMA on arsenides and sulfarsenides measure Pt concentrations above 33–35ppm, the proximity of the Pt L lines and the As K line severely degrade de detection limit for Pt in micro-PIXE analyses, increasing the LOD up to 440ppm. The rest of PGE were randomly detected by both methods at concentrations close to their LOD.     

In-line determination of heavy elements by gamma ray-induced energy-dispersive K-line XRF

In-line determination of heavy elements, especially in nuclear fuel reprocessing solutions by means of XRF analysis and -emitting radionuclides as excitation sources for the K-lines has been investigated.⁵⁷Co,¹³³Ba and¹⁹²Ir are used as radionuclide sources. U, Np, and Pu can be determined from the lower ppm range up to the saturation concentration of about 400 g/l. In case of Pu concentrations >100 mg/l the detection limits for U and Np increase. A matrix effect due to the composition of the solution is observed, which depends only on the density of the solution. At higher activities of fission products in the solution, an increase of the background count rate but no interferences are observed. This allows determination of heavy elements in fission product solutions.     

Differential-pulse adsorptive stripping voltammetry of the herbicides metamitron and isometiozine

Summary A new extract-photometric method is proposed for determining trace amounts of Fe³⁺ based on the formation of a coloured complex with 2-indolehydroxamic acid (2-IHA), that can be extracted into a solution of trioctylmethylammonium chloride solution in toluene. Beer's law was obeyed between 0.06 g/g and 1.25 g/g (minimum error range) of iron in the aqueous phase, with a relative error (p=0.05) of ±0.86%. Molar absortivity at 455 nm was 6500 l mol^–1 cm^–1. The method was applied to the determination of iron in various samples: commercial pharmaceutical nutritional preparations, wine and standard samples of Portland cement and magnesite.     

Microwave digestion methods for the determination of trace elements in brain and liver samples by inductively coupled plasma mass spectrometry

Two microwave digestion systems (open-focused and closed-pressurized) were tested for the mineralization of human brain and bovine liver (NIST SRM 1577a) as dissolution steps prior to the determination of 16 trace elements (Bi, Cd, Co, Cs, Cu, Fe, Hg, Mn, Mo, Pb, Rb, Sb, Sn, Sr, Tl, and Zn) by inductively coupled plasma mass spectrometry (ICP-MS). Digestion parameters (mass of sample, digestion mixture, and power/time steps) were optimized using temperature and pressure sensors. Digestions with the open-focused microwave system require larger volumes of conc. HNO₃ and 30% H₂O₂ than digestions with the closed-pressurized system. Both systems produce correct results for the bovine liver samples. The concentrations obtained for the digests of the open-focused system tend to be less precise than the concentrations from the closed-pressurized digests. Because the open-focused digests must be diluted to 50 mL to bring the acid concentration to 0.7–2.0 mol/L required by the ICP-MS (closed-pressurized digests need to be diluted to only 20 mL), the detection limits for the system with the open-focused digestion are higher than for the system with the closed-pressurized digestor. The open-focused digestor cannot handle more than 150 mg brain tissue, whereas the closed-pressurized system can mineralize 470 mg. The latter method gave better results with brain tissue than the open-focused system. The preparation of brain tissue as reference material for the determination of trace elements in brain samples is described.