高效氯氰菊酯微胶囊的制备、表征及释放性能

以高效氯氰菊酯为芯材, 乙基纤维素为壁材, 采用溶剂蒸发法制备了微胶囊, 并对其理化性能进行表征, 通过单因素实验研究了工艺参数对微胶囊外观形貌、 粒径大小及分布、 包封率、 载药量和缓释性能的影响. 结果表明, 乳化剂种类和剪切时间可以显著影响微胶囊的外观形貌; 随着乳化剂用量增大, 微胶囊粒径减小, 分布变窄, 当Tween-80用量从4%增加至8%时, 微胶囊平均粒径从59.9 μm减少到29.8 μm, 跨距也从1.21减少到0.72. 随着芯壁比(质量比)减小, 微胶囊粒径和包封率均逐渐增大, 载药量逐渐减小, 当芯壁比为1:1.75时, 包封率可以达到70%以上. 微胶囊释放动力学模型符合Ritger-Peppas模型(lgQ=lgk+nlgt); 平均粒径相近而载药量不同时, 初期载药量最小的样品释放速率慢, 累积释放率低; 载药量相近而平均粒径不同时, 粒径大的样品释放速率低, 累积释放率也低.     

用溶剂蒸发法研制维生素C微胶囊

本文用溶剂蒸发法研制了以乙基纤维素、羟两基甲基纤维素苯二甲酸酯等聚合物为包覆材料的维生素C微胶囊,探讨了微胶囊化的条件和包覆效果,并测定了微胶囊的载药量及其溶解释放性能。     

聚[2-(甲基丙烯酰氧)乙基三甲基氯化铵]/阿拉伯胶复凝聚法十二醇微胶囊的制备

将聚[2-(甲基丙烯酰氧)乙基三甲基氯化铵](PMTC)和阿拉伯胶(GA)在一定条件下进行了复凝聚,并对影响复凝聚实验的壁材配比、壁材浓度、离子强度等因素进行了考察.实验结果表明,PMTC与GA配比为1/3.22,壁材总浓度为4%时复凝聚效率最高;体系中不同浓度的氯化钠的存在会对复凝聚起到不同程度的抑制作用.在实验确定的最佳复凝聚条件下以有机小分子化合物十二醇作为芯材进行了包覆,制备了不同壁芯比例的微胶囊.对微胶囊的包覆率及载药量进行了测量,并对它们的释放行为进行了考察.包覆有十二醇的复合微胶囊大小一般在几微米.随着壁材与芯材比例的增大,胶囊载药量逐渐降低,微胶囊释放十二醇的速率明显变小,但包覆率却无明显变化规律.     

甲胺基阿维菌素苯甲酸盐微胶囊的制备与表征

以三聚氰胺-甲醛树脂为壁材,采用原位聚合法制备了甲胺基阿维菌素苯甲酸盐微胶囊,研究了三聚氰胺与甲醛的质量比、芯壁比、乳化剂、搅拌速度与时间、pH值、温度等因素对微胶囊形成的影响,对制备的微胶囊进行了表征,测定了甲维盐微胶囊化前后的光解率。结果表明,三聚氰胺与甲醛质量比为1∶2、芯材与壁材质量比为3∶2、以质量分数1%羟乙基纤维素(HEC)为乳化剂、在1000r/min搅拌速度下、pH=5.0和50℃保温2h可制备出形貌较好、平均粒径4.4μm的甲维盐微胶囊。红外光谱分析证明,甲维盐已完全被包覆在微胶囊中。紫外分光光度法测定其缓释性能良好。光解实验表明,微胶囊化可有效降低甲维盐原药的光解。     

大豆分离蛋白-十二烷基硫酸钠微胶囊的制备与表征

以大豆分离蛋白(SPI)和十二烷基硫酸钠(SDS)为壁材, 以十六烷为芯材, 通过复凝聚法制备了微胶囊. 首先确定了SPI和SDS发生复凝聚的适宜pH、SPI/SDS配比、壁材浓度等. 在确定的实验条件下进行复凝聚, 凝聚物产率可达85%. 改变搅拌转速和芯壁比, 考察它们对微胶囊性能的影响. 用光学显微镜观察了微胶囊形貌. 用气相色谱测定了微胶囊的载药量和包覆率. 芯壁比为2、搅拌转速为400 r/min时所制备微胶囊的载药量可达61%. 随着芯壁比的增大, 微胶囊粒径及载药量都逐渐增大.     

复凝聚法制备昆虫激素模拟物十二醇微胶囊及其释放性能

以明胶(GE)和阿拉伯胶(AG)为壁材, 通过复凝聚法将昆虫激素模拟物十二醇(C12OH)包覆在微胶囊中, 改变微胶囊壁材的浓度和交联度, 探讨了体系中C12OH的可控释放性能. 通过对壁材质量比为1及不同pH条件下的壁材凝聚率测试确定最佳复凝聚的pH为4.0; 考察了不同分散剂对微胶囊及其分散液性能的影响, 确定以Tween 20/Span 80(质量比1∶1)作为复凝聚法包覆C12OH体系的分散剂. 在壁材质量分数大于或等于3%条件下制备的微胶囊粒径大于壁材质量分数为2%的微胶囊, 胶囊的载药量和C12OH包覆率明显高于后者. 增加交联剂的用量, 壁材交联度、胶囊的载药量和C12OH包覆率都显著提高. 在相同用量的情况下, 用甲醛作交联剂时得到的微胶囊的交联度比用戊二醛作交联剂时的要低, 但其对C12OH的包覆率更高. 通过扫描电镜对微胶囊进行了分析, 认为GE与AG通过复凝聚能够将C12OH包覆在微胶囊内部. 对胶囊中C12OH在恒温恒湿条件下的释放研究结果表明, 3%与4%壁材含量下1%戊二醛交联的微胶囊和5%壁材含量下4%戊二醛交联的微胶囊中C12OH的释放行为有明显的可控性. 通过调节微胶囊的壁材含量和交联度可以达到昆虫激素可控释放的目的.     

以聚脲为囊壁薄荷素油微胶囊的制备及表征

采用界面聚合法,以薄荷素油为芯材,以异佛尔酮二异氰酸酯为壁材单体,在催化剂四甲基乙二胺作用下和水反应形成聚脲外壳,制备出了薄荷素油微胶囊.通过扫描电镜、激光粒度分析仪、傅里叶红外光谱仪及热重分析仪分别对香精微胶囊的表面形貌、粒径分布、单体反应情况和热稳定性进行了分析表征.通过紫外可见分光光度计对香精微胶囊包覆率进行了测定.并分析了均质化速率和微胶囊平均粒径的关系以及不同乳化剂种类和芯壁比条件下微胶囊的形貌特征.结果表明,微胶囊平均粒径随均质化速率的增大而减小,下降到1μm左右时趋于平稳,当乳化剂采用聚乙烯醇且芯壁比为4∶1时,微胶囊形貌最佳,为规整球形.最终测得微胶囊芯材包覆率为84.09 wt%,粉末状微胶囊样品含油率为72.64 wt%,并且微胶囊芯材具有良好的热稳定性.     

改性胺微胶囊固化剂制备工艺的优化与性能

以改性胺1618固化剂为囊芯、脲醛树脂为壁材单体,采用界面聚合技术,成功制备了一种新型聚脲改性胺微胶囊固化剂。通过正交设计试验,考察了芯壁质量比、乳化剂种类和质量分数及搅拌速率对微胶囊包覆率、粒径大小及分布情况的影响,并确定了最佳制备工艺条件。采用马尔文激光粒度仪、扫描电镜对微胶囊粒径大小、分布情况及表面形貌进行表征,采用热重分析仪及傅里叶变换红外光谱对其化学结构进行表征,通过拉伸试验对自修复材料的断裂力学性能进行研究。结果表明,该微胶囊含有固化剂芯材,其热稳定温度为198°C,当芯壁质量比为0.7∶1、乳化剂为阿拉伯胶、乳化剂质量分数为1.5%、搅拌速率为800r/min时,所制备的微胶囊包覆率达到79.8%,平均粒径为207.5nm,呈规则的球形,分散性及表面致密性好。当基体材料中加入质量分数为1%的微胶囊后,拉伸强度提高64%,弹性模量提高287%。     

胆甾相液晶微胶囊制备与表征

为了实现液晶的分散、保护和致稳,完成了DYE液晶的包覆。对该方法所采用的芯壁比、乳化剂含量、剪切速度和剪切时间等影响微胶囊包覆因素做了研究。首先,用自由基聚合法制备了液晶微胶囊。接着,以偏光显微镜(POM)检验液晶微胶囊的包覆效果,即在液晶微胶囊经过加热前后,液晶是否仍然保持其独有的光学特性。然后,在分析比较SEM和激光粒度仪等评价方法的性能的基础上,说明了液晶微胶囊的形貌及粒径分布。最后,利用傅里叶变换红外光谱仪再次验证了液晶微胶囊的包覆效果。实验结果表明：当芯壁比为5:4时,剪切速度为7000 rpm,剪切时间为10 min,乳化剂HSMA含量为5 ml时,微胶囊的形貌及粒径分布最优,液晶微胶囊显色性能最优。研制的DYE液晶微胶囊具有单分散性好、显色性优、耐高温能力强等优点,并以此微胶囊制备了热至变色液晶膜。     

磁性微胶囊的制备及其药物缓控释性能

用乳液-凝胶法制备了磁性壳聚糖/海藻酸钠微胶囊. 在壳聚糖/海藻酸钠微胶囊中掺入Fe3O4磁性中空球, 使微胶囊具有磁靶向性能. 以头孢拉定作为模型药物研究了载药磁性微胶囊的载药量、包封率及药物缓控释性能等. 结果表明, 提高头孢拉定的初始浓度可以提高载药量, 却不利于提高药物的包封率. 所制备的微胶囊在各种缓冲溶液中长时间内具有显著的缓释效果, 并具有pH 刺激响应释放的性能, 即在模拟胃液中的药物释放率大大降低, 而在模拟体液和肠液中的释放时间大大延长, 可达50 h以上. 另外, 在外加磁场作用下, 微胶囊表现出良好的磁定向运动性能, 为磁靶向药物输送提供基础.     

Performances of new sugar-bearing poly(acrylamide) copolymers as DNA sieving matrices and capillary coatings for electrophoresis

We have synthesized two new sugar monomers, allylamine of gluconic and lactobionic acid, by opening the corresponding lactone ring with allylamine. These monomers were copolymerized with acrylamide leading to formation of copolymers with a relative molecular mass of 288000 and 180000 Da, respectively. Double-stranded DNA fragments were separated in entangled solutions of these linear polymers in capillary electrophoresis. Resolution, peak spacing and peak width were the parameters taken into account to evaluate the quality of the separation achieved with the new polymers. This work indicates that the copolymers of acrylamide and allyl gluconic acid have a high sieving capacity and provide a performance similar to that of hydroxyethylcellulose (HEC) of comparable viscosity. Unlike HEC, this copolymer selfcoats onto the capillary wall, allowing DNA fragments to be efficiently separated in an uncoated capillary.     

海藻酸钠-壳聚糖-粉末活性炭生物微胶囊的传递性能研究

测定不同分子量的聚乙二醇(PEG)溶液透过海藻酸钠-壳聚糖-粉末活性炭(SA-CA-PAC)生物微胶囊的性能,确定了SA-CA-PAC膜的截留分子量在PEG4000以下。研究了葡萄糖、乳糖、氨基酸等小分子的物质在SA-CA-PAC微胶囊中的扩散性能,用数学模型计算出了这些物质在微胶囊的混合扩散系数Dm以及相应的微胶囊膜层中扩散系数D1,结果表明小分子量的物质具有较好的扩散性能,且Dl<相似文献   

Adsorption and Exchange Dynamics in Aging Hydroxyethylcellulose Layers on Silica

The adsorption kinetics of hydroxyethylcellulose (HEC) on silica and relaxations in adsorbed HEC layers were probed using total internal reflectance fluorescence and near-Brewster reflectivity. Like many random-coil polymers, HEC was found to adsorb at the transport-limited rate. Relaxations occurred at nearly constant interfacial mass when HEC layers were exposed to aqueous solvent, causing the subsequent exchange of chains between the layer and the free solution to become increasingly hindered. Eventually, on the time scale of a day, layers became immobilized and unable to accommodate chains from free solution. A continued fluorescence decay, beyond time scales that could be probed with self exchange, suggested further relaxations of the adsorbed HEC. The polydisperse HEC system (with an average molecular weight near 450,000) behaved qualitatively similar to molecular weight standard polyethylene oxide (PEO) layers on silica. For instance, relaxations in PEO layers occurred on a time scale of 10-20 h, like the HEC layers. Young layers of the latter, however, exhibited self-exchange kinetics that were an order of magnitude slower than PEO layers of similar age. This difference in adsorbed layer dynamics was attributed to HEC's stiffer backbone, compared with flexible PEO. Copyright 2000 Academic Press.     

十八烷/聚(St-MMA)相变微胶囊制备及表征

采用乳液聚合的方法,分别选取聚苯乙烯(PS)、聚甲基丙烯酸甲酯(PMMA)或苯乙烯和甲基丙烯酸甲酯的共聚物为壁材,正十八烷为芯材,十二烷基苯磺酸钠(SDBS)为乳化剂,制作相变储能微胶囊。用粒径分析仪、透射电子显微镜(TEM)、热重分析仪(TG)和示差扫描量热测试仪(DSC)对微胶囊的形貌、相变热性能和热稳定性分别进行表征。结果表明:壁材选取两者共聚物,当两种单体的比例为St∶MMA=1∶5,SDBS用量为1.5g(总质量的3%)时,微胶囊粒径大小均匀,粒子分散性好,壁材的包裹性好。微胶囊的放热峰为起始温度为27.3℃,终止温度为31.9℃,相变温度为28.9℃,相变焓为48.4J/g。TG表明长期使用温度不能超过131℃。IR分析微胶囊中含有芯材和壁材。这种十八烷/聚(St-MMA)相变微胶囊可以用于诸能材料。     

The effect of temperature and solvent on the morphology of microcapsules doped with a europium beta-diketonate complex

Fluorescent microcapsules doped with a europium beta-diketonate complex were fabricated for the first time by stepwise adsorption of polyelectrolytes and europium complex using the layer-by-layer technique. The influence of temperature and solvent treatment on the morphology of the microcapsules was investigated. Intense red light emission of the microcapsules could be clearly observed by fluorescence microscopy before and after treatment. Remarkable shrinking, decrease of the inner volume and increase of the wall thickness were observed using atomic force microscopy (AFM) and transmission electron microscopy (TEM) after thermal treatment. The shrinkage induced by annealing could be recovered by dissolving in ethanol solution, which was confirmed by AFM and TEM. Morphology variation of the luminescent microcapsules induced by annealing or solvent are both attributed to the molecular rearrangement of polyelectrolytes. While the shrinkage by annealing is an entropy driven process with formation of more coiled conformations of polyelectrolytes the morphology variation by ethanol might be due to the effective screening of electrostatic interaction within the polyelectrolyte multilayers and the changed interaction between hydrophobic fragments present in the polyelectrolytes.     

Preparation and barrier properties of the microcapsules added nanoclays in the wall

Preparation of microcapsules applied to the fabrication of self‐healing composites has attracted a lot of attention. However, the leakage of core material from the microcapsule is a major problem in self‐healing microcapsules. Proper dispersion of layered silicates within the wall of microcapsule is a strategy for improving the barrier properties of the microcapsule. In the present study, poly(urea‐formaldehyde) (PUF) microcapsules containing dicyclopentadiene (DCPD) were prepared by in situ polymerization. For the preparation of UF/clay nanocomposite microcapsules, acid‐modified montmorillonite (H‐MMT) was used as an effective catalyst for the condensation of urea and formaldehyde, and the condensation polymerization in the galleries resulted in the delamination of the clay, as confirmed by TEM and XRD analysis. Scanning electron microscopy (SEM) was applied to observe the morphology of the microcapsules and the barrier property of microcapsules was investigated by thermal gravimetry (TG) analysis and mass release method. On comparison with conventional microcapsules (CMs), nanocomposite microcapsules (NCMs) have better barrier property. This can be attributed to the nanocomposite structure of the microcapsules, where nanosized montmorillonite dispersed in UF to decrease the core material cross‐over. Copyright © 2008 John Wiley & Sons, Ltd.     

Flow behaviour of titanium dioxide dispersions in the presence of 2-hydroxyethyl cellulose

 The effects of 2-hydroxyethyl cellulose (HEC) of weight-average molecular weight 15,000, 90,000 and 7,20,000 on the rheological properties of TiO₂ dispersions were evaluated. For all three HECs, the maximum yield stress, τ_ymax, (occurred at zero zeta potential), decreased with increasing HEC concentration. Interestingly, the largest reduction in τ_ymax was observed with the HEC with the highest molecular weight. This reduction was attributed to steric interaction arising from adsorbed HEC. Adsorbed high-molecular-weight HEC formed an effectively thicker steric barrier because of its larger size and higher adsorption capacity. Bridging interactions that were expected to be important for the high-molecular-weight HEC were found to be unimportant here. In the flocculated regime, HEC enhanced the shear-thinning characteristics of the TiO₂ dispersions. Received: 8 November 1999 Accepted: 20 December 1999