芦丁修饰电极研究多巴胺的电化学响应

通过循环伏安法(CV)制备了芦丁修饰电极,研究多巴胺(DA)在修饰电极上的电化学行为.结果表明,芦丁修饰膜对DA的氧化有明显的催化作用,并且可以消除抗坏血酸(AA)对DA测定的干扰.DA的浓度在1.0×10-7～9.5×10-6 mol/L范围内与其氧化峰电流呈线性关系,相关系数为0.9996,检出限为1.0×10-8 mol/L.将该修饰电极用于注射液样品中DA的测定,结果表明该修饰电极可用于实际样品分析.     

纳米金修饰的碳纤维超微电极在高浓度抗坏血酸体系中选择性测定多巴胺

将柠檬酸三钠与硼氢化钠还原氯金酸制备纳米金颗粒,采用一步恒电位沉积的方法在碳纤维超微电极上沉积纳米金颗粒,并对电极进行电化学表征。分别对100μmol/L DA、1mmol/L AA在该电极上修饰前后的电化学行为进行了研究,结果表明在浓度为1 mmol/L抗坏血酸共存下,DA的浓度(0. 1～10μmol/L)与氧化峰电流成正比,线性回归方程为Ip(μA)=200 c(μmol/L)+2×10~(-4),相关系数R~2=0. 9979,线性范围0. 1～10μmol/L,检出限为1. 28×10~(-2)μmol/L (S/N=3)。方法可用于较高浓度抗坏血酸共存下对多巴胺的选择性测定。     

聚对氨基苯磺酸/氧化石墨烯修饰电极同时测定多巴胺和抗坏血酸

用循环伏安法制备了聚对氨基苯磺酸/氧化石墨烯修饰玻碳电极(PABSA/GO/GCE),研究了多巴胺(DA)和抗坏血酸(AA)在该修饰电极上的电化学行为,并建立了同时测定多巴胺和抗坏血酸电化学分析新方法,相对于裸玻碳电极,该电极测定DA和AA的峰电流明显增加。实验结果表明:在实验条件下,DA测定的线性范围为0.50～300μmol/L;检出限为5.0μmol/L。AA测定的线性范围是0.10～2.4 mmol/L,检出限为0.50μmol/L。     

应用单壁碳纳米管修饰纳米碳纤维电极同时测定多巴胺和抗坏血酸

采用滴涂法制备了单壁碳纳米管修饰的纳米碳纤维电极,研究了多巴胺(DA)、抗坏血酸(AA)及其混合溶液在修饰前后电极上的电化学行为。在20 mmol/L Tris-HCl(pH 7.4)缓冲溶液中,修饰电极对DA和AA具有很好的电催化作用。采用差示脉冲伏安法对DA与AA混合溶液氧化峰电流与浓度的关系进行定量分析,DA和AA的氧化峰电流在1.0×10-7~5.0×10-5mol/L和1.0×10-5~1.0×10-3mol/L范围内与浓度呈线性关系,其线性回归方程及相关系数分别为Ip=0.0012c+4×10-9,r=0.9907;Ip=10-5c+7×10-10,r=0.9974,两种物质的检测限分别达到8.0×10-9mol/L和2×10-6mol/L。     

单分子层γ-氨基丁酸共价修饰玻碳电极同时测定多巴胺、尿酸和抗坏血酸

采用电氧化法制备了一种新型γ-氨基丁酸(ABA)修饰的玻碳电极.X射线光电子能谱(XPS)和循环伏安法研究表明,ABA以单分子层状态以C—N键牢固地共价键合在电极表面.该修饰电极对多巴胺(DA)、尿酸(UA)和抗坏血酸(AA)都具有良好的电化学催化特性.在pH=7.0磷酸缓冲溶液中,DA,UA和AA分别于0.45,0.25和0.07V(vs.Ag/AgCl)有一个良好的、独立的阳极方波伏安峰,表明此修饰电极可用于这3种物质的同时测定.与DA,UA和AA的方波伏安峰电流呈线性关系的浓度范围分别为4.0～400,2.0～500和1.0～600μmol/L,检测限(3δ)分别为1.6,1.2和0.8μmol/L.该修饰电极具有良好的灵敏度、选择性和稳定性,并具有抗污染能力.     

纳米NiO-还原石墨烯复合修饰玻碳电极的制备及电催化检测多巴胺

制备了纳米NiO-还原石墨烯复合修饰电极(NiO-rGO/GCE),并用于多巴胺(DA)的检测。用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了DA在该修饰电极上的电化学行为。结果表明,在pH=7.0的磷酸盐缓冲溶液(PBS)中,该修饰电极对DA有良好的催化作用。DA浓度在5.0×10-7~3.2×10-5 mol/L范围内与氧化峰电流呈良好的线性关系,检出限为3.8×10-8 mol/L。用该修饰电极直接测定了血清中DA含量,回收率在97.8%~101.1%之间。     

多巴胺在聚亚甲基蓝/石墨烯修饰电极上的电化学行为研究

利用电聚合方法在石墨烯修饰的玻碳电极表面制备了聚亚甲基蓝/石墨烯修饰电极(PMB/GH/GCE)。采用循环伏安法(CV)和差分脉冲伏安法(DPV)研究了多巴胺(DA)和抗坏血酸(AA)在该修饰电极上的电化学行为。在pH 6.9的磷酸盐缓冲溶液中,DA和AA分别在0.208 V和-0.108 V处产生灵敏的氧化峰,与其在聚亚甲基蓝和石墨烯单层修饰电极上的电化学行为相比,两者的峰电流明显增加,峰电位差达316 mV。研究表明,电聚合方法使亚甲基蓝牢固地非共价修饰到石墨烯上,并产生协同增效作用,较好地提高了电极的灵敏度和分子识别性能,有利于在大量AA存在下实现对DA的选择性测定。在1.00×10-3mol/L AA的存在下,DA的差分脉冲伏安法峰电流与其浓度在1.00×10-7～5.00×10-3mol/L范围内呈良好的线性关系,检出限达1.00×10-8mol/L。将该方法用于盐酸多巴胺注射液的测定,结果满意。     

柠檬酸修饰电极对抗坏血酸、多巴胺和尿酸的同时检测

研究柠檬酸(CA)修饰玻碳电极(CA/GC)在抗坏血酸(AA)、多巴胺(DA)和尿酸(UA)混合体系中的循环伏安(CV)行为.结果表明,AA、DA和UA在CA/GC电极上氧化峰电流增大,且三者氧化峰电位明显分离(ΔEp(DA,AA)=170 mV,ΔEp(DA,UA)=130 mV,ΔEp(AA,UA)=300 mV).据此,可同时检测AA、DA和UA.在优化的实验条件下,AA、DA和UA的氧化峰电流与其浓度分别在2.0×10-6～1.5×10-3mol.L-1,6.0×10-7～1.0×10-3mol.L-1和6.0×10-7～1.0×10-3mol.L-1范围内呈线性关系.该电极重现性好,可用于盐酸多巴胺针剂DA、VC片剂AA及人体尿液UA的测定.     

在抗坏血酸存在下用L-赖氨酸修饰玻碳电极测定多巴胺

采用电化学氧化法制备了L-广赖氮酸单分子层修饰玻碳电极，研究了多巴胺（DA）和抗坏血酸（AA）在该电极上的电化学行为。结果表明，L-广赖氨酸单分子层修饰玻碳电极不仅能改善多巴胺和抗坏血酸的电化学行为，而且能将多巴胺和抗坏血酸二者在裸电极上的完全重叠的单氧化峰分开成为两个完全独立的氧化峰，循环伏安（CV）图上峰间距为507mV，差分脉冲伏安（DPV）图上峰间距为460mV，由此可实现在AA的共存下对样品中的DA进行选择性测定。     

Nafion/胆碱双层膜碳纤维电极探测小白鼠大脑内的多巴胺

制备了胆碱(Ch)共价键植的碳纤维电极(Ch/CFE),进而吸附涂敷一薄层Nafion膜得到了Nafion/Ch/CFE。以循环伏安(CV)法和差分脉冲伏安(DPV)法研究了该电极上多巴胺(DA)的电化学响应。使用DPV法,该电极能良好抵抗代谢产物3,4-二羟苯乙酸(DOPAC)和抗坏血酸(AA)的干扰而选择性测量DA。在1.0 mmol/L AA存在下,使用5 mm长Nafion/Ch/CFE测定DA,检出限(S/N=3)为0.1μmol/L;线性范围为0.4~16μmol/L。该电极适于活体监测。将该电极插入小白鼠大脑纹状体内,实时监测了神经递质DA的浓度及其变化,观察到DA水平由静脉注射药物左旋多巴(L-DOPA)后随时间的响应,并发现针刺激对应于中医"风府穴"的头部皮下组织可引起脑内DA的即时性脉冲释放。     

Electroless Deposition of Thionin onto Glassy Carbon Electrode Modified with Single Wall and Multiwall Carbon Nanotubes: Improvement of the Electrochemical Reversibility and Stability

A simple procedure was developed to prepare a glassy carbon electrode modified with carbon nanotubes (CNTs) and thionin. Abrasive immobilization of CNTs on a GC electrode was achieved by gently rubbing the electrode surface on a filter paper supporting carbon nanotubes, then immersing the GC/CNTs‐modified electrode into a thionin solution (electroless deposition) for a short period of time (5–50 s for MWCNTs and 5–120 s for SWCNTs ). Cyclic voltammograms of the resulting modified electrode show stable and a well defined redox couple with surface confined characteristic at wide pH range 2–12. The electrochemical reversibility and stability of modified electrode prepared with incorporation of thionin into CNTs film was compared with usual methods for attachment of thionin to electrode surfaces such as electropolymerization and adsorption on the surface of preanodized electrodes. The formal potential of redox couple (E°′) shifts linearly toward the negative direction with increasing solution pH. The surface coverage of thionin immobilized on CNTs glassy carbon electrode was approximately 1.95×10^?10 mol cm^?2 and 3.2×10^?10 mol cm^?2 for MWCNTs and SWCNTs, respectively. The transfer coefficient (α) was calculated to be 0.3 and 0.35 and heterogeneous electron transfer rate constants (K_s) were 65 s^?1 and 55 s^?1 for MWCNTs/thionin and SWCNTs/thionin‐modified GC electrodes, respectively. The results clearly show a great facilitation of the electron transfer between thionin and CNTs adsorbed on the electrode surface. Excellent electrochemical reversibility of redox couple, high stability, technically simple and possibility of preparation at short period of time are of great advantages of this procedure for modification of electrodes.     

镧掺杂的二氧化锰/碳纳米管电化学超级电容器复合电极

尽管在二氧化锰/多壁碳纳米管（MnO₂/MWCNTs）上获得了较高的比电容,低电导率仍是制约MnO₂担载量或膜厚度提高的主要障碍.另一个问题是MnO₂/MWCNTs的循环稳定性远低于活性炭.所以截止到目前这一新型材料的应用仍然受到很大的限制.本文采用原位还原的方法制备镧掺杂二氧化锰/多壁碳纳米管电化学超级电容器复合电极材料.分别通过透射电镜（TEM）、扫描电镜（SEM）、X射线衍射（XRD）和傅里叶变换红外（FTIR）光谱等技术对这些复合材料的形貌与结构进行了分析.采用循环伏安法、恒电流充放电法和交流阻抗法对其进行了电化学性能的研究.研究结果表明,通过还原MnO₄^-可以在MWCNTs上形成La掺杂MnO₂复合材料.La掺杂降低了复合电极的电阻,这是因为La的引入可以增大MnO₂的晶格缺陷,从而提高材料的电导率以及电极的电化学性能.因此La掺杂是克服MnO₂本征导电性差的有效途径之一.掺杂La可以在不增大电极电阻的情况下提高MnO₂的担载量或膜厚度.La掺杂的更重要的作用是使以MnO₂/MWCNTs作电极的对称电化学超级电容器的循环性能得到显著改善.此外,La掺杂也使复合电极的比电容得到一定程度的提高.     

Fabrication, Characterization and Electrocatalysis of an Ordered Carbon Nanotube Electrode

A method for fabrication of ordered carbon nanotube (CNT) film,which was template-synthesized within the highly ordered pores of a commercially available alumina template membrane,modified glassy carbon(CNT/GC) electrode was established.The CNT/GC electrode showed excellent electrocatalytic activity toward dopamine electrochemical reaction without introducing any electrochemically active group into CNT film or activating any electrochemically active group into CNT film or activating the electrode electrochemically.DA undergoes ideal reversible electrochemical reaction on CNT/GC electrode at low scan rate(≤20mV/s) with an excellent reproducibility and stability.The CNT/GC electrode might be used in biosensors because the highly ordered CNT may present a steric effect on more efficient redox reactions of biomolecules.     

高分子聚合物-多壁碳纳米管复合物固定漆酶及其在玻碳电极上的直接电子迁移

采用不同结构的高分子聚合物与纯化的多壁碳纳米管(MWCNTs)共混的方法,制备得到聚合物非共价功能化多壁碳管复合物,测定了这些载体对漆酶(lac)的担载量、固定漆酶的比活力及稳定性.以固定漆酶的复合物修饰玻碳(GC)电极后,采用循环伏安法研究这些电极在无氧磷酸盐缓冲液(PBS)中的直接电化学行为及催化氧还原活力,粗略地测定了固定漆酶与电极间电子转移的速率常数.实验结果表明,当聚合物中含亲漆酶基团或能与漆酶活性中心发生相互作用的官能团时利于直接电子转移,而且复合物固定漆酶保持了游离漆酶的天然构象.这些电极中,lac/NIPAM-co-BPCP-M WCNTs/GC(NIPAM-co-BPCP:N-烯丙基-1-苯甲酰基-3-苯基-4,5-2H-4-甲酰胺基吡唑-co-N-异丙基丙烯酰胺)在无氧PBS中发生直接电子转移的式电位(605mV)更接近漆酶活性中心的式电位(580mV),具有较快的异相电子转移速率(0.726s-1),较高的漆酶担载量(103.5mg/g)和固定漆酶比活力(1.68U/mg),较高的催化氧还原能力(氧还原起始电位820mV,在650mV时的催化峰电流为85.5μA)以及良好的重复使用性和长期使用性.     

A Novel Polycatechol/Ordered Mesoporous Carbon Composite Film Modified Electrode and Its Electrocatalytic Application

Polycatechol (PCC) was prepared by electropolymerizing catechol (CC) on the surface of an ordered mesoporous carbon (OMC) modified electrode for the first time. Scanning electron microscopy (SEM) and cyclic voltammetry (CV) were used to characterize the structure and electrochemical behaviors of PCC/OMC nanocomposite film. Compared with the bare GC and OMC/GC electrodes, the PCC/OMC/GC electrode exhibits a good electrocatalysis toward the oxidation of NADH at 0.0 V with a high sensitivity (8.7 mA/mM). These make PCC/OMC/GC electrode a promising candidate for stable and efficient electrochemical sensors for the detection of NADH.     

Cyclic Voltammograms of Ferrocene on Multi‐Walled Carbon Nanotubes (MWCNTs)‐Modified Edge Plane Pyrolytic Graphite (EPPG) Electrode in Room Temperature Ionic Liquids (RTILs) of 1‐Ethyl‐3‐Methylimidazolium Tetrafluoroborate (EMIBF4)

In this work, the electrochemical behavior of ferrocene (Fc) was investigated by cyclic voltammetry (CV) in room temperature ionic liquids (RTILs) of 1‐ethyl‐3‐methylimidazolium tetrafluoroborate (EMIBF₄) on glass carbon (GC), edge plane pyrolytic graphite (EPPG) and multi‐walled carbon nanotube (MWCNTs)‐modified EPPG electrodes, respectively. The results demonstrated that on GC electrode, pairs of well‐defined reversible peaks were observed, while for the electrode of EPPG, the peak potential separation (ΔE_p) is obviously larger than the theoretical value of 59 mV, hinting that the electrode of EPPG is distinguished from the commonly used electrode, consistent with the previous proposition that EPPG has many “defects”. To obtain an improved electrochemical response, multi‐walled carbon nanotubes (MWCNTs) were modified on the electrode of EPPG; the increased peak current and promoted peak potential separation not only proved the existence of “defects” in MWCNTs, but also supported that “creating active points” on an electrode is the main contribution of MWCNTs. Initiating the electrochemical research of Fc on the MWCNTs‐modified EPPG electrode in RTILs and verifying the presence of “defects” on both EPPG and MWCNTs using cyclic voltammograms (CVs) of Fc obtained in RTILs of EMIBF₄, is the main contribution of this preliminary work.     

Adsorptive Stripping Differential Pulse Voltammetric Determination of Risperidone with a Multi‐Walled Carbon Nanotube‐Ionic Liquid Paste Modified Glassy Carbon Electrode

A new composite electrode has been fabricated based on coating multi‐walled carbon nanotubes (MWCNTs) and n‐octylpyridinum hexafluorophosphate (OPPF₆) ionic liquid composite on a glassy carbon (GC) electrode (OPPF₆‐MWCNTs/GCE). This electrode shows very attractive electrochemical performances for electrooxidation of risperidone (RIS) compared to conventional electrodes using carbon and mineral oil, notably improved sensitivity and stability. The oxidation peak potentials in cyclic voltammogram of RIS on the OPPF₆‐MWCNTs/GCE was occurred around 230 mV vs. SCE at Britton–Robinson (B–R) buffer (pH 4.0) at scan rate of 100 mV s^?1. The electrochemical parameters such as diffusion coefficient (D), charge transfer coefficient (α) and the electron transfer rate constant (k/_s) were determined using cyclic voltammetry. Under the optimized conditions, the peak current was linear to risperidone concentration over the concentration range of 10–200 nM with sensitivity of 0.016 μA/nM^?1 using differential pulse voltammetry. The detection limit was 6.54 nM (S/N = 3). The electrode also displayed good selectivity and repeatability. In the presence of clozapine (CLZ) the response of RIS kept almost unchanged. Thus this electrode could find application in the determination of RIS in some real samples. The analytical performance of the OPPF₆‐MWCNTs/GCE was demonstrated for the determination of RIS in human serum and pharmaceutical samples.     

Sensitive Voltammetric Detection of Trace Heavy Metals in Real Water Using Multi‐Wall Carbon Nanotubes/Nafion Composite Film Electrode

Multi‐wall carbon nanotubes (MWCNTs) and Nafion composite film (MWCNTs/Nafion) were used for fabricating electrochemical sensors for the voltammetric detection of trace lead(II) and cadmium(II) in several water samples. The morphology and structure of MWCNTs/Nafion film were characterized by scanning electron microscopy (SEM) and infrared spectrum (IR). The electron transfer of MWCNTs/Nafion composite film was examined by cyclic voltammetry (CV) and electrochemical impedance spectrum (EIS). Various experimental parameters, which influenced the response of MWCNTs/Nafion/GC to target metals, were optimized. The results showed that the synergistic effect was obtained on the MWCNTs/Nafion/GC whose sensitivity and stability were better than those of Nafion‐coated electrode (Nafion/GC) or CNTs/GC. Stability of the Pb(II) and Cd(II) stripping signals was excellent with relative standard deviations (RSD) within 5% (n=10) from one electrode preparation to another, and RSD of 30 µg·L^?1 Pb(II) and Cd(II) were 2.8% and 3.2% for 20 repeated analysis on one single CNTs/Nafion/GC. Over 50 runs, the stability of Pb and Cd detection at the MWCNTs/Nafion conposites electrode was still satisfactory with RSD lower than 6.0%. The determination limits (S/N=3) of the proposed method were determined to be 100 ng·L^?1 for Pb and 150 ng·L^?1 for Cd. Finally, the MWCNTs/Nafion/GC was successfully applied to determine Pb(II) and Cd(II) in different water samples with recoveries of 97%–103% for Pb and 96%–104% for Cd.     

Pt/DNA-MWCNTs/GC电极制备及其H2O2还原的电催化活性

将DNA功能化多壁碳纳米管（MWCNTs）复合材料修饰于玻碳基底（GC）表面制得DNA-MWCNTs/GC电极,并在此基础上电沉积负载Pt纳米颗粒构建了一种新型无酶H₂O₂传感电极. 利用扫描电子显微镜（SEM）表征制得的修饰电极,同时通过循环伏安法和计时电流法研究了该传感电极的H2O2响应性能. 结果表明,该传感电极的H₂O₂检测在0.04 ~ 18.07 mmol·L^-1浓度范围内成线性相关,检出限3.85 μmol·L^-1（S/N = 3）,且有良好的重现性、稳定性与选择性.     

基于BCNTs/GC电极的鸟嘌呤与腺嘌呤电化学行为及其同时检测

利用掺硼碳纳米管（BCNTs）/GC电极研究了鸟嘌呤（G）和腺嘌呤（A）的电化学氧化行为. 与GC和CNTs/GC电极相比,BCNTs/GC电极具有更强的电催化活性,且响应电流明显增加. 两混合样品在BCNTs/GC电极上的氧化峰间隔较大,可实现对A和G的同时检测.