A NADH Sensor Based on 1,2‐Naphththoquinone Electropolymerized on Multi‐walled Carbon Nanotubes Modified Glassy Carbon Electrode

A new carbon nanotubes modified electrode (poly‐Nq‐MWCNTs/GCE) was fabricated by electropolymerization of 1,2‐naphththoquinone to the surface of multi‐walled carbon nanotubes modified electrode by casting method. The morphology of the nanocomposite was characterized by scanning electron microscopy. Cyclic voltammetry and chronoamperometry were applied to investigate the electrochemical properties of the poly‐Nq‐MWCNTs nanocomposite modified electrode. The result of electrochemical experiments showed that such modified electrode had a favorable catalytic ability to oxidation of β‐nicotinamide adenine dinucleotide (NADH). The resulted sensor was sensitiveness to NADH and achieved 95β of the steady‐state current within 5s. Furthermore, the anodic peak current was linear to the concentration of NADH for the range from 1.0 μM to 0.14 mM. The linear equation was: I(μA) = 0.3987 + 0.1035c (μmol/L), the correlation coefficient r = 0.9962, the detect limit is down to 1 × 10^?7 M (S/N = 3) and the sensitivity is 0.1035 μA/mmol. The well catalytic activity of the sensor was ascribed to the synergistic effect role played by MWCNTs and poly‐Nq. Moreover, the based sensor possesses good stability and reproducibility.     

Electrochemical Behaviors of Baicalin at an Electrochemically Activated Glassy Carbon Electrode and Its Determination in Human Blood Serum

Electrochemical behavior of baicalin (BA) at an electrochemically activated glassy carbon electrode (GCE) had been investigated in Britton‐Robinson (B‐R) buffer solution (pH = 2.87) by cyclic voltammetry (CV) and square wave voltammetry (SWV). The experimental results suggested that the electrode exhibited an electrocatalytic activity toward the redox of BA. The electron transfer coefficient (α) and the standard rate constant (k_s) of BA at the electrochemically activated glassy carbon electrode were calculated. The reaction mechanism was proposed and discussed in this work. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of BA in the range of 5.0 × 10^?8 to 3.0 × 10^?6 mol L^?1 (r = 0.9990), with a detection limit of 2.0 × 10^?8 mol L^?1. The relative standard deviation (R.S.D.) for five times successful determination of 1.0 × 10^?6 mol L^?1 baicalin were 2.9%. The proposed method was also successfully applied for the determination of BA in human blood serum.     

A sensitive and selective sensor‐coated molecularly imprinted sol–gel film incorporating β‐cyclodextrin‐multi‐walled carbon nanotubes and cobalt nanoparticles‐chitosan for oxacillin determination

A sensitive and selective imprinted electrochemical sensor for the determination of oxacillin was developed based on indium tin oxide electrode. The proposed sensor was decorated with imprinted sol–gel film and cobalt nanoparticles‐chitosan/β‐cyclodextrin‐multiwalled carbon nanotubes nanocomposites. The surface morphologies of the modified electrodes were characterized by scanning electron microscopy and transmission electron microscope. The stepwise assembly process and electrochemical behavior of the novel sensor were characterized by differential pulse voltammetry, cyclic voltammetry and Amperometric i‐t response. The imprinted sensor displayed excellent selectivity toward oxacillin. Meanwhile, the introduced cobalt nanoparticles‐chitosan and β‐cyclodextrin‐multi‐walled carbon nanotubes exhibited noticeable amplified electrochemical response signal. The differential voltammetric anodic peak current was linear to oxacillin concentration in the range from 2.0 × 10^?7 to 1.0 × 10^?4 mol·l^?1, and the detection limit was 6.9 × 10^?9 mol·l^?1. The proposed imprinted sensor was applied to the determination of oxacillin in human blood serum samples successfully. Copyright © 2011 John Wiley & Sons, Ltd.     

Electrochemical Behaviors of Adenosine‐5′‐triphosphate on Molecular Wire Modified Carbon Paste Electrode and Its Sensitive Detection

A new electrochemical method was proposed for the determination of adenosine‐5′‐triphosphate (ATP) based on the electrooxidation at a molecular wire (MW) modified carbon paste electrode (CPE), which was fabricated with diphenylacetylene (DPA) as the binder. A single well‐defined irreversible oxidation peak of ATP appeared on MW‐CPE with adsorption‐controlled process and enhanced electrochemical response in a pH 3.0 Britton‐Robinson buffer solution, which was due to the presence of high conductive DPA in the electrode. The electrochemical parameters of ATP were calculated with the electron transfer coefficient (α) as 0.54, the electron transfer number (n) as 1.9, the apparent heterogeneous electron transfer rate constant (k_s) as 2.67 × 10^?5 s^?1 and the surface coverage (Γ_T) as 4.15 × 10^?10 mol cm^?2. Under the selected conditions the oxidation peak current was proportional to ATP concentration in the range from 1.0 × 10^?7 mol L^?1 to 2.0 × 10^?3 mol L^?1 with the detection limit as 1.28 × 10^?8 mol L^?1 (3σ) by sensitive differential pulse voltammetry. The proposed method showed good selectivity without the interferences of coexisting substances and was successful applied to the ATP injection samples detection.     

Electrochemistry of adenosine-5′-diphosphate on ionic liquid modified carbon electrode and its detection

A sensitive electrochemical method was proposed for the determination of adenosine-5′-diphosphate (ADP) on an ionic liquid (IL) 1-(3-chloro-2-hydroxy-propyl)-3-methylimidazole chloride modified carbon paste electrode (CPE) in a pH 4.5 Britton-Robinson (B-R) buffer solution. Compared with CPE, IL modified CPE (CILE) showed strong electrocatalytic ability to promote the electrochemical oxidation of ADP. A well-defined irreversible oxidation peak of ADP appeared at +1.381 V with an adsorption-controlled process, which was due to the presence of high conductive IL on the electrode. The experimental conditions were optimized and the electrochemical parameters of ADP were calculated with the electron transfer coefficient (α) as 0.293, the electron transfer number (n) as 1.23, the apparent heterogeneous electron transfer rate constant (k ^s) as 3.325 × 10^?6 s^?1 and the surface coverage (Γ_T) as 0.92 × 10^?8 mol/cm². Under the optimum conditions, the oxidation peak current was linear to ADP concentration in the range from 3.0 to 1000.0 μmol/L with the detection limit as 2.78 μmol/L (3σ) by differential pulse voltammetry. The CILE also eliminated the interferences of commonly coexisting substances and was successfully applied to detect the ADP artificial samples.     

Chitosan Incorporating Cetyltrimethylammonium Bromide Modified Glassy Carbon Electrode for Simultaneous Determination of Ascorbic Acid and Dopamine

Simultaneous determination of a neurotransmitter, dopamine (DA), and ascorbic acid (AA) is achieved at neutral pH on a chitosan incorporating cetyltrimethylammonium bromide (CTAB) modified glassy carbon (GC) electrode. Differential pulse voltammetry (DPV) technique was used to investigate the electrochemical response of DA and AA at a glassy carbon electrode modified with chitosan incorporating CTAB. An optimum 6.0 mmol L^?1 of CTAB together with 0.5 wt% of chitosan was used to improve the resolution and the determination sensitivity. In 0.1 mol L^?1 aqueous phosphate buffer solution of pH 6.8, the chitosan‐CTAB modified electrode showed a good electrocatalytic response towards DA and AA. The anodic peak potential of DA shifted positively, while that of AA shifted negatively. Thus, the difference of the anodic peaks of DA and AA reached 0.23 V, which was enough to separate the two anodic peaks very well. The presented method herein could be applied to the direct simultaneous determination of DA and AA without prior treatment. The anodic peak currents (I_pa) of DPV are proportional to DA in the concentration range of 8 μM to 1000 μM, to that of AA 10 μM to 2000 μM, with correlation coefficients of 0.9930 and 0.9945, respectively. The linear range is much wider than previously reported.     

Simultaneous Differential Pulse Voltammetric Determination of Ascorbic Acid and Caffeine in Pharmaceutical Formulations Using a Boron‐Doped Diamond Electrode

A cathodically pretreated boron‐doped diamond electrode was used for the simultaneous anodic determination of ascorbic acid (AA) and caffeine (CAF) by differential pulse voltammetry. Linear calibration curves (r=0.999) were obtained from 1.9×10^?5 to 2.1×10^?4 mol L^?1 for AA and from 9.7×10^?6 to 1.1×10^?4 mol L^?1 for CAF, with detection limits of 19 μmol L^?1 and 7.0 μmol L^?1, respectively. This method was successfully applied for the determination of AA and CAF in pharmaceutical formulations, with results equal to those obtained using a HPLC reference method.     

Electrochemical Oxidative Detection of Guanosine‐5′‐triphosphate Based on a New Ionic Liquid Modified Carbon Paste Electrode

An ionic liquid (IL) 1‐(3‐chloro‐2‐hydroxy‐propyl)‐3‐methylimidazolium trifluoroacetate was used as the modifier for the preparation of the modified carbon paste electrode (CPE). The IL‐CPE showed excellent electrocatalytic activity towards the oxidation of guanosine‐5′‐triphosphate (5′‐GTP) in a pH 5.0 Britton‐Robinson buffer solution. Due to the presence of high conductive IL on the electrode surface, the electrooxidation of 5′‐GTP was greatly promoted with a single well‐defined irreversible oxidation peak appeared. The electrode reaction was an adsorption‐controlled process and the electrochemical parameters of 5′‐GTP on IL‐CPE were calculated with the electron transfer coefficient (α) as 0.44, the electron transfer number (n) as 1.99, the apparent heterogeneous electron transfer rate constant (k_s) as 2.21 × 10^?9 s^?1 and the surface coverage (Γ_T) as 1.53 × 10^?10 mol cm^?2. Under the selected conditions a linear calibration curve between the oxidation peak currents and 5′‐GTP concentration was obtained in the range from 2.0 to 1000.0 μmol L^?1 with the detection limit as 0.049 μmol L^?1 (3σ) by differential pulse voltammetry. The proposed method showed good selectivity to the 5‘‐GTP detection without the interferences of coexisting substances and the practical application was checked by measurements of the artificial samples.     

Sensitive Electrochemical Determination of Catechol with a Graphene Modified Carbon Ionic Liquid Electrode

In this paper a graphene (GR) modified carbon ionic liquid electrode (CILE) was fabricated and used as the voltammetric sensor for the sensitive detection of catechol. Due to the specific physicochemical characteristics of GR such as high surface area, excellent conductivity and good electrochemical properties, the modified electrode exhibits rapid response and strong catalytic activity with high stability toward the electrochemical oxidation of catechol. A pair of well‐defined redox peaks appeared with the anodic and the cathodic peak potential located at 225 mV and 133 mV (vs.SCE) in pH 6.5 phosphate buffer solution, respectively. Electrochemical behaviors of catechol on the GR modified CILE were carefully investigated and the electrochemical parameters were calculated with the results of the electrode reaction standard rate constant (k_s) as 1.24 s^?1, the charge transfer coefficient (α) as 0.4 and the electron transfer number (n) as 2. Under the selected conditions the differential pulse voltammetric peak current increased linearly with the catechol concentrations in the range from 1.0 × 10^‐7 to 7.0 × 10^?4mol L‐1 with the detection limit as 3.0 × 10^?8mol L‐1 (3σ). The proposed method was further applied to the synthetic waste water samples determination with satisfactory results     

Electroanalytical Determination of Cd(II) and Pb(II) in Bivalve Mollusks using Electrochemically Reduced Graphene Oxide‐based Electrode

An electrochemical sensor for the simultaneous determination of Cd(II) and Pb(II) by square wave anodic stripping voltammetry (SWASV) in bivalve mollusks using a glassy carbon electrode modified with electrochemically reduced graphene oxide has been developed. The modified surface was characterized by cyclic voltammetry, high resolution scanning electron microscopy (HR‐SEM), and Raman spectroscopy. The optimum conditions were optimized and a linear range was observed from 15–105 μg L^?1 with a limits of detection of 15 μg L^?1 for Cd(II) and Pb(II). The methodology was validated and applied in different samples of commercial bivalve mollusks with satisfactory results. The high conductivity and greater surface area of the modifying agent improves the preconcentration capacity of the electrochemical sensor, allowing to develop a simple, rapid and sensitive analysis in the detection of lead and cadmium in marine resources.     

An Electrochemical Sensor Based on Ni(II) Complex and Multi Wall Carbon Nano Tubes Platform for Determination of Glucose in Real Samples

In the present paper, a stable and selective non‐enzymatic sensor is reported for determination of glucose (Glc) by using a carbon paste electrode modified with multiwall carbon nanotubes and Ni(II)‐SHP complex as modifier in an alkaline solution. This modified electrode showed impressive activity for oxidation of glucose in NaOH solution. Herein, Ni(II)‐SHP acts as a suitable platform for oxidation of glucose to glucolactone on the surface of the modified electrode by decreasing the overpotential and increasing in the current of analyte. Under the optimum conditions, the rate constant and electron transfer coefficient between electrode and modifier, were calculated to be 1.04 s⁻¹ and 0.64, respectively. The anodic peak currents indicated a linear dependency with the square root of scan rate and this behavior is the characteristic of a diffusion controlled process. So, the diffusion coefficient of glucose was found to be 3.12×10⁻⁶ cm² s⁻¹ due to the used number of transferred electron of 1. The obtained results revealed two linear ranges (5 to 190.0 μM (R²=0.997), 210.0 to 700.0 μM (R²=0.999)) and the detection limit of 1.3 μM for glucose was calculated by using differential pulse voltammetry (DPV) method. Also, the designed sensor was used for determination of glucose in the blood serum and urine samples. Some other advantages of Ni(II)‐SHP/CNT/CPE sensor are remarkable reproducibility, stability and selectivity which can be related to using nanomaterial of carbon nanotubes due to enhancement of electrode surface area.     

Simultaneous Electrochemical Determination of Hydroquinone and Bisphenol A using a Carbon Paste Electrode Modified with Silver Nanoparticles

In this paper, a rapid and sensitive modified electrode for the simultaneous determination of hydroquinone (HQ) and bisphenol A (BPA) is proposed. The simultaneous determination of these two compounds is extremely important since they can coexist in the same sample and are very harmful to plants, animals and the environment in general. A carbon paste electrode (CPE) was modified with silver nanoparticles (nAg) and polyvinylpyrrolidone (PVP). The PVP was used as a reducing and stabilizing agent of nAg from silver nitrate in aqueous media. The nAg‐PVP composite obtained was characterized by transmission electron microscopy and UV‐vis spectroscopy. The electrochemical behavior of HQ and BPA at the nAg‐PVP/CPE was investigated in 0.1 mol L⁻¹ B−R buffer (pH 6.0) using cyclic voltammetry (CV) and square wave voltammetry (SWV). The results indicate that the electrochemical responses are improved significantly with the use of the modified electrode. The calibration curves obtained by SWV, under the optimized conditions, showed linear ranges of 0.09–2.00 μmol L⁻¹ for HQ (limit of detection 0.088 μmol L⁻¹) and 0.04–1.00 μmol L⁻¹ for BPA (limit of detection 0.025 μmol L⁻¹). The modified electrode was successfully applied in the analysis of water samples and the results were comparable to those obtained using UV‐vis spectroscopy.     

Multi‐Walled Carbon Nanotubes (MWCNT)‐Ionic Liquid‐Modified Carbon Paste Electrode: Probing FurazolidoneDNA Interactions and DNA Determination

The interactions of furazolidone (Fu) with double‐stranded calf thymus DNA (dsDNA) on the multi‐walled carbon nanotubes‐ionic liquid‐modified carbon paste electrode (MWCNT‐IL‐CPE) have been studied by cyclic voltammetry. In the presence of DNA, the cathodic peak current of Fu decreased and the peak potential shifted to a positive potential, indicating the intercalative interaction of Fu with DNA. The binding constant of Fu with DNA and stoichiometric coefficient has been determined according to the Hill's model. This electrochemical method was further applied to the determination of DNA. Two linear calibration curves were obtained for DNA detection in the concentration ranges of 0.03–0.10 and 0.10–4.0 μg l^?1 with a detection limit of 0.027 μg l^?1. The method was successfully applied to analyze Fu in serum samples.     

Electrochemical determination of acetaminophen in the presence of propranolol using an electrode modified with a Schiff base from 2-hydroxy-1-naphthaldehyde and ethylenediamine and multi-walled carbon nanotubes

A carbon paste electrode, modified with N,N′-bis-(2-hydroxy-1-naphthalidene)ethylenediamine and multi-walled carbon nanotubes (HNED-MWCNPE), was used for the determination of acetaminophen (ACOP) and propranolol (PP). Cyclic voltammetry (CV), chronocoulometry, chronoamperometry and differential pulse voltammetry (DPV) techniques were employed to study electro-oxidation of ACOP. The results revealed that the modified electrode showed an electrocatalytic activity toward the anodic oxidation of acetaminophen by a marked enhancement in the current response in buffered solution at pH 8.0. Some kinetic parameters such as the electron transfer coefficient (α) were also determined for the ACOP oxidation. The linear concentration range of 1 × 10^?3?1 × 10^?6 M with a detection limit of 4.6 × 10^?8 M (n = 16) for ACOP was obtained using DPV (pH 8.0). The modified electrode shows good sensitivity, selectivity and stability. The prepared electrode was also applied for the determination of ACOP in human blood serum.     

Development of Electrochemical Biosensor Based on Nanostructured Carbon Materials for Paracetamol Determination

This work describes the development of a biosensor for paracetamol (PAR) determination based on a glassy carbon electrode (GCE) modified with multiwalled carbon nanotubes (MWCNT) and laccase enzyme (LAC), which was immobilized by means of covalent crosslinking using glutaraldehyde. Voltammetric investigations were carried out by cyclic voltammetry (CV), differential pulse voltammetry (DPV) and square wave voltammetry (SWV). The biosensor was characterized by Scanning Electron Microscope (SEM) and Fourier Transform Infrared Spectroscopy (FT‐IR). The results showed that the use of MWCNT/LAC composite increased the sensor sensitivity, compared to bare glassy carbon electrode. Factors affecting the voltammetric signals such as pH, ionic strength, scan rate and interferents were assessed. Linear range, limit of detection (LOD) and limit of quantitation (LOQ) obtained were 10–320 μmol L^?1, 7 μmol L^?1 and 10 μmol L^{? 1}, respectively. The developed biosensor was successfully applied to PAR determination in urine and pharmaceutical formulations samples, with recovery varying from 99.96 to 106.20 % in urine samples and a relative standard deviation less than 1.04 % for PAR determination in pharmaceutical formulations. Therefore, the MWCNT‐LAC/GCE exhibits excellent sensitivity and can be used to PAR determination as a viable alternative in clinical analyzes and quality control of pharmaceutical formulations, through a simple, fast and inexpensive methodology.     

Determination of 1-hydroxypyrene in human urine by a multi-wall carbon nanotubes-modified glassy carbon electrode

A multi-walled carbon nanotubes (MWNTs) modified glassy carbon electrode (MWNT-GCE) was used to study the electrochemical behaviour of1-hydroxypyrene (1-OHP) and applied to its determination. The results showed that the modified electrode had a strong adsorptive ability to 1-OHP and enhances its electrochemical signal. By square wave voltammetry, the linear relationship of 1-OHP was 6?×?10^?9???8?×?10^?7?mol?L^?1 with a linear correlation coefficient of 0.996, and the detection limit was 1?×?10^?10?mol?L^?1. Compared with other published methods, this newly proposed method possesses many advantages such as very low detection limit, fast response, low cost and simplicity. And this method was applied successfully in the determination of 1‐OHP in real human urine samples.     

Investigation of Electrochemical Oxidation of Methanol at a Carbon Paste Electrode Modified with Ni(II)‐BS Complex and Reduced Graphene Oxide Nano Sheets

In the present research, the electro oxidation of methanol was investigated by different electrochemical methods at a carbon paste electrode (CPE) modified with bis(salicylaldehyde)‐nickel(II)‐dihydrate complex (Ni(II)‐BS) and reduced graphene oxide (RGO) (which named Ni(II)‐BS/RGO/CPE) in an alkaline solution. This modified electrode showed very efficient activity for oxidation of methanol. It was found that methanol was oxidized by NiOOH groups generated by further electrochemical oxidation of nickel (II) hydroxide on the surface of the modified electrode. The rate constant and electron transfer coefficient were calculated to be 2.18 s^?1 and 0.4, respectively. The anodic peak currents revealed a linear dependency with the square root of scan rate. This behaviour is the characteristic of a diffusion controlled process, so the diffusion coefficient of methanol was found to be 1.16×10^?5 cm² s^?1 and the number of transferred electron was calculated to be 1. Moreover, differential pulse voltammetry (DPV) investigations showed that the peak current values were proportional to the concentration of methanol in two linear ranges. The obtained linear ranges were from 0.5 to 100.0 µM (R²=0.991) and 400.0 to 1300.0 µM (R²=0.992), and the detection limit was found to be 0.19 µM for methanol determination. Generally, the Ni(II)‐BS/RGO/CPE sensor was used for determination of methanol in an industrial ethanol solution containing 4.0 % methanol.     

Voltammetric Determination of L‐Dopa Using a Carbon Nanotubes‐Nafion Modified Glassy Carbon Electrode

Abstract

A method for determination of L‐dopa by the adsorption stripping voltammetry (ASV) using a multiwalled carbon nanotubes (MWNTs)–Nafion modified glassy carbon electrode (GMGCE) was proposed. This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed and the anodic peak potential is ca. 0.374V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of L‐dopa in samples. There is a good linear relationship between the peak current (i_p) and L‐dopa concentration in the range of 3.5×10^?7～1.5×10^?5 mol/L, with the limit of detection 5.0×10^?8 mol/L.     

A Graphite‐Polyurethane Composite Electrode for the Analysis of Furosemide

A graphite‐polyurethane composite electrode has been used for the determination of furosemide, a antihypertensive drug, in pharmaceutical samples by anodic oxidation. Cyclic voltammetry and electrochemical impedance spectroscopy were used to characterize the electrooxidation process at +1.0 V vs. SCE over a wide pH range, with the result that no adsorption of analyte or products occurs, unlike at other carbon‐based electrode materials. Quantification was carried out using cyclic voltammetry, differential pulse voltammetry, and square‐wave voltammetry. Linear ranges were determined (up to 21 μmol L^?1 with cyclic voltammetry) as well as limits of detection (0.15 μmol L^?1 by differential pulse voltammetry). Four different types of commercial samples were successfully analyzed. Recovery tests were performed which agreed with those obtained by spectrophotometric evaluation. The advantages of this electrode material for repetitive analyzes, due to the fact that no electrode surface renewal is needed owing to the lack of adsorption, are highlighted.     

Electrochemical determination of homocysteine using carbon nanotubes modified paste electrode and isoprenaline as a mediator

Homocysteine (HCy) is an important amino acid containing thiol group and is known as a risk factor in relation to ischemic heart disease and stroke. In this study the electrochemical determination of homocysteine (HCy) has been described using isoprenaline hydrochloride (ISP) as a mediator on multiwall carbon nanotubes modified paste electrode (MWCNTPE). Electrochemical behavior of homocysteine was investigated by cyclic voltarrtmetry and chronoamperometry. The cyclic voltammograms showed that the electrocatalytic oxidation of homocysteine occurs in the presence of ISP on the surface of MWCNTPE at a potential about 640 mV. Also, results showed that the oxidatation peak current of HCy at the modified carbon nanotubes electrode was more than unmodified electrode. The diffusion coefficient and the kinetic parameters including electron transfer coefficient and rate constant of electrocatalytic reaction were determined using electrochemical approaches. Linear sweep voltammetry results showed that electrocatalytic oxidation peak current of HCy had linear dynamic range in the range of 5.0 to 800 μmol L^?1 with a detection limit of 3.3 μmol L^?1 in pH 3.5 (universal buffer).