Electric property of mixed conductor BaIn1−xCoxO3−δ

We synthesized BaIn_1−xCo_xO_3−δ (x = 0–0.8) with a defective perovskite structure by partly replacing In with Co in Ba₂In₂O₅. Based on XRD measurements, the synthesized compound was found to have cubic perovskite and orthorhombic brownmillerite structures depending on the amount of Co. BaIn_1−xCo_xO_3−δ (x = 0.2 and 0.3) showed high total electrical conductivities without undergoing the structural transformation that the original Ba₂In₂O₅ undergoes. Some of the samples showed both electronic and oxide ionic conductivities. At the same time, the oxide ionic conductivity was comparable with that of Ba₂In₂O₅. For example, the sample with x = 0.1 had a total electrical conductivity of 4.7 × 10^− 1 S cm^− 1 and an oxide ion transport number of 0.52 at 850 °C.     

Electrical conductivity and thermal expansion of the oxy-cuspidine Gd4Al2O9 substituted with Ca and Sr

The series of Gd_4 ? xM_xAl₂O_9 ? x/2 (M = Ca, Sr) with x = 0, 0.01, 0.05, 0.10 and 0.25 was prepared by the citrate complexation method. Both Gd_4 ? xCa_xAl₂O_9 ? x/2 and Gd_4 ? xSr_xAl₂O_9 ? x/2 show the monoclinic cuspidine structure with space group of P2₁/c up to 0.05–0.1 and 0.01–0.05 mol for Ca and Sr, respectively. Beyond the substitution limit of Gd₄Al₂O₉, GdAlO₃ and SrGd₂Al₂O₇ appear as additional phases. The highest electrical conductivity obtained at 900 °C yielded σ = 1.49 × 10^? 4 S/cm for Gd_3.95Ca_0.05Al₂O_8.98. In comparison, the conductivity of pure Gd₄Al₂O₉ was σ = 1.73 × 10^? 5 S/cm. The conductivities determined are in a similar range as those of other cuspidine materials investigated previously. The thermal expansion coefficient of Gd₄Al₂O₉ at 1000 °C was 7.4 × 10^? 6 K^? 1. The phase transition between 1100 and 1200 °C reported earlier changes with increasing substitution of Ca and Sr.     

Synthesis and electrical transport properties of Lu2+xTi2−xO7−x/2 oxide-ion conductors

The Lu_2+xTi_2−xO_7−x/2 (x = 0; 0.052; 0.096; 0.286; 0.44; 0.63; 33.3–49 mol% Lu₂O₃) nanoceramics with partly disordered pyrochlore-type structure are prepared by sintering freeze-dried powders obtained by a co-precipitation technique with 1600 °C annealing. Similar to pyrochlore-like compositions in the zirconate system, some of the new titanates are good oxide-ion conductors in air. The new solid-state electrolytes have oxide-ion conductivity in the interval of 1.0 × 10^− 3 – 2.5 × 10^− 3 S/cm at 740 °C in air. This value of conductivity is comparable with that of ZrO₂/Y₂O₃ ceramics. The conductivity of Lu_2+xTi_2−xO_7−x/2 depends on the chemical composition. The highest ionic conductivity is exhibited by nearly stoichiometric Lu_2+xTi_2−xO_7−x/2 (x = 0.096; 35.5 mol% Lu₂O₃) material containing ∼ 4.8 at.% Lu_Ti anti-site defects.     

Mixed conductivity and electrocatalytic performance of SrFeO3-δ–SrAl2O4 composite membranes

Oxygen-ionic and electronic transport in dense (SrFe)_1−x(SrAl₂)_xO_z composites, consisting of strontium-deficient Sr(Fe,Al)O_3-δ and SrAl₂O₄ phases, is determined by the properties of perovskite-like solid solution. Increasing the content of SrAl₂O₄, with a total conductivity as low as 5 × 10^− 7 −  10^− 5 S × cm^− 1 at 973–1273 K in air, results in the gradual decrease of the partial conductivities, but also enables the suppression of thermal expansion. Compared to single-phase SrFe_1−xAl_xO_3-δ, (SrFe)_1−x(SrAl₂)_xO_z composites exhibit enhanced thermomechanical properties, while the oxygen permeability of these materials has similar values. The composite membranes exhibit stable performance under air/(H₂–H₂O–N₂) and air/(CH₄–He) gradients at 973–1173 K. The oxidation of dry methane by oxygen permeating through (SrFe)_0.7(SrAl₂)_0.3O_z results in dominant total oxidation, suggesting the necessity to incorporate a reforming catalyst into the ceramic reactors for natural gas conversion.     

An oxygen permeable membrane La0.8Sr0.2(Ga0.8Mg0.2)1 − xCrxO3 − δ for a reduced atmosphere

Mixed electron hole and oxide ion conducting perovskite-type oxides, La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ (0 ≤ x ≤ 1.0)_, were prepared by solid state reaction. The phase stability and the oxygen permeation properties of the oxides were examined as a function of the content of Cr. La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ has a perovskite related tetragonal phase with x = 0.1 to 0.8. The total electrical conductivity of La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ increases with increasing x. The oxygen permeation flux across the La_0.8Sr_0.2(Ga_0.8Mg_0.2)_1 ? xCr_xO_3 ? δ membranes at higher temperatures increases with x up to x = 04. The maximum oxygen permeation flux of 1.6 × 10^? 7 mol^? 1 cm^? 2 at 1100 °C in a oxygen activity gradient of air/10^? 2 Pa is observed in La_0.8Sr_0.2(Ga_0.8Mg_0.2)_0.6Cr_0.4O_3 ? δ. This perovskite-type oxide is stable under an oxygen partial pressure of 7 × 10^? 10 Pa at 1000 °C.     

High temperature properties of the n = 2 Ruddlesden–Popper phases (La,Sr)3(Fe,Ni)2O7−δ

The crystal chemistry and mixed conductor properties of the n = 2 member of the Ruddlesden–Popper (R–P) phases Sr_3−xLa_xFe_2−yNi_yO_7−δ with 0 ≤ x ≤ 0.3 and 0 ≤ y ≤ 1.0 have been studied at high temperature. High-temperature X-ray diffraction and thermogravimetric measurements of the equilibrium pO₂ (10^− 5 ≤ pO₂ ≤ 1 atm) in the temperature range 400 ≤ T ≤ 1000 °C indicate that the Sr₃FeNiO_7−δ phase is able to accommodate a large oxygen non-stoichiometry (δ ∼ 1.5) without structural transformations. The electrical conductivity and oxygen permeability increase with the substitution of Ni for Fe in the range 550 ≤ T ≤ 1000 °C. The electrical transport of the Sr₃FeNiO_7−δ phase is thermally activated and the activation energy decreases with the substitution of Ni for Fe for a given oxygen content. The increase in the oxygen permeation flux with increasing Ni content is due to an increasing oxygen non-stoichiometry and a lower activation energy for permeation.     

Electrical conductivity of fully densified nano CaZr0.90In0.10O3 − δ ceramics prepared by a water-based gel precipitation method

Water-based gel precipitation method was first applied to synthesize high purity nano CaZr_0.90In_0.10O_3 ? δ powders suitable for fabricating dense ceramics at lower temperature. By using CaCO₃, Zr(NO₃)₄ and In(NO₃)₃ as raw materials, PEG as dispersant, CaZr_0.90In_0.10O_3 ? δ with an average particle size of about 40 nm was obtained at 850 °C, which was nearly 350 °C lower than that of traditional solid-state reaction method. Fully densified ceramics with an average grain size of 200–300 nm were obtained at 1350 °C, a temperature about 250 °C lower than that of traditional sintering techniques. Experimental results showed that the flexure stress, total, bulk and grain boundary protonic conductivities of the ceramics were more favorable than those of the ceramics fabricated at 1500 °C and 1600 °C from the powders synthesized by solid-state reaction method.     

Effect of Eu dopant concentration in SrCe1 − xEuxO3 − δ on ambipolar conductivity

The europium dopant concentration in strontium cerate was studied to achieve maximum hydrogen permeation. In order to determine high ambipolar conductivity, total conductivity and open circuit potential measurements were performed. Among the three different compositions of Eu-doped SrCe_1 ? xEu_xO_3 ? δ (x = 0.1, 0.15 and 0.2) studied, SrCe_0.9Eu_0.1O_3 ? δ showed highest total conductivity between 600 °C and 900 °C. However, transference number measurements showed increasing electronic conductivity with increasing dopant concentration and a stronger temperature dependence for electronic conduction. Therefore, the highest ambipolar conductivity was obtained over the compositional range from SrCe_0.85Eu_0.15O_3 ? δ to SrCe_0.8Eu_0.2O_3 ? δ depending on temperature. Finally, the hydrogen permeation flux was calculated based on the ambipolar conductivity and compared with experimental results.     

Synthesis and structural characterization of perovskite type proton conducting BaZr1−xInxO3−δ (0.0 ≤ x ≤ 0.75)

Solid state sintering has been used to prepare the cubic perovskite structured compounds BaZr_1−xIn_xO_3−δ (0.0 ≤ x ≤ 0.75). Analysis of X-ray powder diffraction (XRPD) data reveals that the unit cell parameter, a, increases linearly with an increased Indium concentration. XRPD data was also used to demonstrate the completion of sample hydration, which was reached when the materials showed a set of single-phase Bragg-peaks. Dynamic thermogravimetric analysis (TGA) data showed that approx. 89% of the total number of available oxygen vacancies can be filled in BaZr_1−xIn_xO_3−δ for x = 0.50, and that the maximum water uptake occurs below 300 °C. Rietveld analysis of the room temperature neutron powder diffraction (NPD) data confirmed the average cubic symmetry (space group Pm-3m), and an expansion of the unit cell parameter after the hydration reaction. The strong O–H stretch band, 2500–3500 cm^− 1, in the infrared absorbance spectrum clearly manifests the presence of protons in the hydrated material. Proton conductivity of hydrated BaZr_1−xIn_xO_3−δ, x = 0.75 was investigated during heating and cooling cycles under dry argon atmosphere. The total conductivity during the heating cycle was nearly two orders of magnitude greater than that of cooling cycle at 300 °C, whilst these values were similar at higher temperatures i.e. T > 600 °C.     

YBCO films buffered by pyrochlore Nd2Mo2O7 layer on YSZ substrates by chemical solution deposition

A chemical solution deposition process was used to grow epitaxial Nd₂Mo₂O₇ (NMO) buffer layers on YSZ substrates to produce YBa₂Cu₃O_7?δ (YBCO) coated conductors. The NMO precursor solution prepared using metal acetylacetonates was spin-coated onto single crystal YSZ substrate of 10 mm × 10 mm in size at 3000 rpm for 30 s and heat-treated at 1000 °C for 2 h in Ar after calcinated at 550 °C for 1 h. The YBCO film was deposited by TFA-MOD route on top of the NMO/YSZ architecture. The phase purity and the crystalline orientation of NMO and YBCO films were evaluated by X-ray diffraction (XRD). Scanning electron microscopy (SEM) and atomic force microscopy (AFM) were used to observe their microstructure and their surface roughness. The critical current density (J_c) of YBCO film on NMO/YSZ is 1.8 MA/cm² at 77 K in self-field, which indicates that the Nd₂Mo₂O₇ is a potential buffer for YBCO coated conductor.     

Enhancement microwave dielectric properties of La(Mg0.5Sn0.5)O3 ceramics by substituting La3+ with Sm3+

The microwave dielectric properties of La_1?xSm_x(Mg_0.5Sn_0.5)O₃ ceramics were examined with a view to their exploitation for mobile communication. The La_1?xSm_x(Mg_0.5Sn_0.5)O₃ ceramics were prepared by the conventional solid-state method with various sintering temperatures. The X-ray diffraction patterns of the La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics revealed no significant variation of phase with sintering temperatures. Apparent density of 6.59 g/cm³, dielectric constant (ε_r) of 19.9, quality factor (Q×f) of 70,200 GHz, and temperature coefficient of resonant frequency (τ_f) of ?77 ppm/°C were obtained for La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics that were sintered at 1500 °C for 4 h. The dielectric constant, and τ_f of La_0.97Sm_0.03(Mg_0.5Sn_0.5)O₃ ceramics were almost independent with the sintering temperature as the sintering temperature varied from 1450 to 1600 °C.     

Critical temperature and orthorhombicity of Y2Ba4Cu7O15−δ

Superconducting properties have been systematically studied for oxygen content controlled Y₂Ba₄O₇O_15?δ (Y247) polycrystalline bulks sintered under various conditions, 940–975 °C and P(O₂) = 4–16 atm. T_c of oxygen annealed Y247 samples at 400 °C varied largely depending on the sintering conditions from ～60 to ～90 K. Samples sintered under higher P(O₂) exhibited lower T_c, whereas they were confirmed to be of Y247 single phase by powder X-ray analyses. Strong relationship between orthorhombicity defined as 1000(b ? a)/(a + b) and T_c was found in Y247 as in the cases of REBa₂Cu₃O_7?δ with light rare-earth elements, such as La, Nd, Sm, Eu and Gd. In addition, T_c‘s of samples with nominal compositions of Y_2+xBa_4?xO₇O_15?δ systematically decreased with an increase of x. These results indicated that partial substitution of Y for Ba occurred in the Y247 compounds possibly due to high occupancy ratio of oxygen at the Cu–O_1-δ chain during the sintering process.     

Effect of strontium addition on europium-doped ceria properties

Nanopowders of composition Ce_0.9(Eu_1 ? xSr_x)_0.1O_2 ? δ (x = 0, 0.1, 0.3, 0.5, and 0.7) were prepared by the Pechini method. The microstructure and properties of powders and sintered ceramics are discussed in this paper. X-ray diffraction (XRD) and Raman spectroscopy revealed that all powders calcined at 550 °C were single phase, with the cubic fluorite-type structure. The good sintering properties of the synthesized nanopowders allowed us to obtain dense ceramics (> 96% theoretical density). Dense ceramics with density higher than 96% of the theoretical value were obtained without the need of sintering aid. The morphology of the sintered ceramics was evidenced by scanning electron microscopy (SEM). The ionic conductivities of doped and co-doped ceria ceramics were investigated as a function of temperature by using AC impedance spectroscopy in the temperature range 250–800 °C. Impedance spectra indicate a significant diminution of grain boundary resistance after partial substitution of Eu with Sr in europia-doped ceria sample, especially in the low and intermediate-temperature range. The best conductivity was evidenced for the Ce_0.9Eu_0.09Sr_0.01O_2 ? δ composition.     

Effects of composition and frozen-in conditions on bulk and grain boundary conductivities of Yb2Ti2O7-based materials

The present work provides a comprehensive interpretation of factors which affect cation and/or anion disordering in Yb₂Ti₂O₇-based materials, and their effects on transport properties. It also provides guidelines for further improvements of transport properties. Powder processing and thermal history may play major roles, especially when anti-site cation exchange is likely to occur at typical sintering temperatures, as confirmed by structural refinement. One found that the cooling rate may also determine changes in frozen-in conditions. Excessive sintering temperatures affect both the bulk and grain boundary properties of samples with composition Yb₂Ti₂O₇; this was ascribed to the formation of a Ti-rich amorphous phase, and corresponding excess of Yb in the bulk phase. Anti-site occupancy of B-site positions was found to affect ionic conductivity, as demonstrated for conditions that cause cation heterogeneities in Yb₂Ti₂O₇, and also by analysing conductivity data for compositions with excess of Yb. The conductivity data obtained for Yb_2 + xTi_2 ? xO_7 ? d become less dependent on sample preparation, possibly because deliberate composition changes play a prevailing role, compared to intrinsic cationic and anionic disorders. Samples with slight excess of Ti retain prevailing ionic conductivity, which differs significantly from the effects of a typical donor additive on ionic and electronic conductivities.     

Proton conductivity and low temperature structure of In-doped BaZrO3

The proton conductivity and structural features of In³⁺ substituted BaZrO₃ samples, i.e., BaZr_1−xIn_xO_3−δ, were investigated. Rietveld analysis of low temperature (10 K) neutron powder diffraction data collected on as-prepared and deuterated samples confirmed cubic symmetry (space group Pm-3m) for all compositions. The level of oxygen vacancies refined in the as-prepared samples were in good agreement with the values expected to conserve charge neutrality, whilst an increase in oxygen occupancy, reflecting the incorporation of OD⁻ species, was obtained for the deuterated materials. An expansion of the unit cell parameter, a, was observed as a function of In³⁺ doping as well as after the deuteration reaction. The conductivity of pre-hydrated and dry samples was measured using impedance methods. For 25% In-doped BaZrO₃, the low T (300 °C) conductivity of the heating cycle of the dried sample was greater than that of the cooling cycle of the pre-hydrated sample indicating a greater number of protons in the nominally dry sample. In contrast, the conductivity values were similar at higher temperatures e.g. T > 500 °C where proton conduction is not dominant.     

Chemical diffusion of water in the double perovskites Ba4Ca2Nb2O11 and Sr6Ta2O11

The mechanism and kinetics of water incorporation in the double perovskites Ва₄Ca₂Nb₂O₁₁ and Sr₆Ta₂O₁₁ has been investigated (T = 300÷500 °C and aH₂O = 1 · 10^− 3÷2.2 · 10^− 2). The formation of hydration products Ba₄Ca₂Nb₂O₁₁·xH₂O and Sr₆Ta₂O₁₁·xH₂O (0.2 < x < 0.50) was limited by the diffusion of H₂O. It has been found that the concentration dependences of D˜_H2O are the same for both samples: small increasing of D˜_H2O with increasing x. The temperature dependences of the chemical diffusion coefficients of water for compositions of Ba₄Ca₂Nb₂O₁₁·0.35H₂O and Sr₆Ta₂O₁₁·0.35H₂O could be described with close activation energies of E_a = 0.38 ± 0.03 eV and E_a = 0.49 ± 0.03 eV, respectively. The chemical diffusion coefficients of water are nearly one order of magnitude smaller for tantalate Sr₆Ta₂O₁₁. This result correlates with lower oxygen and proton conductivities in Sr₆Ta₂O₁₁ as the consequence of lower mobilities.     

Oxygen adsorption properties of YBaCo4O7-type compounds

The oxygen adsorption and desorption of newly found compounds RBaCo₄O₇ (R = Y, Dy–Lu, In) were investigated by thermogravimetry (TG) in the temperature range from room temperature to 1100 °C. The influence of Co replaced by Zn and Fe on the oxygen diffusion properties of YBaCo₄O₇ was also studied. TG results showed clearly that all RBaCo₄O₇ compounds basically experience two oxygen adsorption and desorption processes in the temperature range 20∼1100 °C in oxygen flow. One happens at about 200∼450 °C and the another happens at about 660∼1050 °C. The differences between the resulting states by adsorbing oxygen at lower and high temperature were discussed based on the X-ray diffraction (XRD) patterns and TG data. We showed evidence that the oxygen adsorption at the lower temperature has a small activation energy, while the oxygen adsorption at the higher temperature has a large activation energy. The oxygen adsorbed at high temperature will destroy the RBaCo₄O₇ structure. Zn substituting in the YBaCo_4 − xZn_xO₇ influences the oxygen diffusion behavior prominently, the amount of oxygen adsorbed becomes increasingly weak with the increase of Zn content and disappears completely for the samples with x ≥ 2.0. However, replacement of Co by Fe has little effect on the oxygen absorption process.     

Electrochemical supercapacitor studies of hierarchical structured Co2+-substituted SnO2 nanoparticles by a hydrothermal method

Hierarchical structured Co-doped SnO₂ nanoparticles are prepared by a low temperature hydrothermal process. The structural and surface morphologies of the SnO₂ and Sn_1?xCo_xO₂ nanoparticles are studied by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), transmission electron microscopy (TEM), and scanning electron microscopy (SEM). The Sn_1?xCo_xO₂ nanoparticles form with a tetragonal rutile structure during the hydrothermal process without further calcination. The pseudocapacitance behavior of the Sn_1?xCo_xO₂ nanoparticles is characterized by cyclic voltammetry (CV) in 1.0 M H₂SO₄ electrolyte. The specific capacitance (SC) is found to increase with an increase in cobalt content. A maximum SC of 840 F g^?1 is obtained for a Sn_0.96Co_0.04O₂ composite at a 10 mV s^?1 scan rate.     

Ionic and electronic conductivity of Yb2+xTi2−xO7−x/2 materials

Bulk and grain boundary conductivities of Yb_2+xTi_2−xO_7−x/2 (x = 0, 0.1, 0.18 and 0.29) materials were studied by impedance spectroscopy in the range 300–900 °C in air. Ionic and electronic conductivities were separated by both ion blocking Hebb–Wagner measurements and total conductivity measurements as a function of oxygen partial pressure in the temperature range 700–1000 °C. The oxygen partial pressure dependence of the total conductivity shows that these materials are nearly pure ionic conductors in air and that the ionic conductivity decreases for Yb-rich compositions. This was interpreted as a predominant effect of a decrease in mobility of ionic charge carriers, opposing the expected increase in concentration of oxygen vacancies with increasing Yb content. The studied materials become mixed conductors under typical fuel conditions, except possibly at temperatures below about 700 °C. Yb-excess slightly suppresses the electronic conductivity.     

Effect of Fe doping on the room temperature ferromagnetism in chemically synthesized (In1−xFex)2O3 (0 ⩽ x ⩽ 0.07) magnetic semiconductors

Observation of room temperature ferromagnetism in Fe doped In₂O₃ samples (In_1−xFe_x)₂O₃ (0 ⩽ x ⩽ 0.07) prepared by co-precipitation technique is reported. Lattice parameter obtained from powder X software shows distinct shrinkage of the lattice constant indicating an actual incorporation of Fe ions into the In₂O₃ lattice. X-ray diffraction data measurements show that the entire sample exhibits single phase polycrystalline behavior. SEM micrographs showed the prepared powder was in the range 25–36 nm. SEM EDS mapping showed the presence of Fe and In ions in the Fe doped In₂O₃ sample. The highest remanence magnetization moment (6.624 × 10⁻⁴ emu/g) is reached in the sample with x = 0.03.