Silver based mercury film electrode: Part II. The influence of aging of electrode on the electrode processes of various metal ions

The cyclic voltammetric behaviour of 8 metal ions at solid silver amalgam electrodes prepared by aging of a thin silver based mercury film electrode (SBMFE) and by deposition of silver and mercury on platinum were investigated. It was established that such electrodes behave in relation to some metals (Pb, Bi, Sn) similarly as silver electrodes i.e. the cyclic curves obtained with these electrodes at concentration 10^?3M range show a prepeak-postpeak system corresponding to deposition and dissolution of the monolayer of deposit. On the other hand under the same conditions no prepeaks were observed for cadmium, zinc and thallium. In all cases investigated the heights of anodic stripping peaks were lower on curves obtained with aged SBMFE than on those obtained with fresh SBMFE having a mercury layer 1 μm thick.     

An iridium based mercury film electrode: Part II. Comparison of mercury-film electrode behaviors: theory versus reality

An experimental study of a 2 mm diameter iridium based mercury film rotating disk electrode (IrMFE) is presented. Using anodic stripping voltammetry and test ions of cadmium, lead and zinc, the effects of Hg film thickness on peak potential, half-width and peak height are compared with the predictions given by the De Vries and Van Dalen theory. The response of the Ir-MFE was found to be theoretical for Hg film thicknesses less than 1 μm. Application of this classical theory to real Hg film electrodes, on any type of substrate, is found to be inappropriate when the Hg film thickness begins to exceed 1 μm. It is also shown that the stripping peak characteristics at a semi-spherical film electrode can be estimated by assuming that it is composed of a large number of annular flat films. The individual responses of the flat films can be summed to give the overall semi-spherical response.     

Square-wave anodic stripping voltammetry with a mercury-plated reticulated vitreous carbon electrode

A rotating mercury-plated reticulated vitreous carbon (RVC) electrode is tested for square-wave anodic stripping voltammetry; RVC provides very large surface areas which are easily plated with mercury. Despite the ill-defined geometry of the electrode, the square-wave stripping peaks are very well defined; their behaviour conforms partly to known theory for square-wave stripping from mercury film electrodes. Fast analytical determinations of lead and cadmium in the μg l^?1 range are facilitated by the high efficiency of the preconcentration step and the high sensitivity given by the stripping waveform.     

Voltammetry at the mercury film electrodes: Comparison of theoretical and experimental results obtained for indium in thiocyanate medium

The voltammetric behaviour of the In(III)-In(Hg) system was studied at the silver-, graphite-, and glassy carbon-based mercury film electrodes under cyclic and stripping conditions in thiocyanate media. The reversible curves obtained at high thiocyanate ion concentration showed a good agreement with theoretical predictions, particularly for the cathodic process. The anodic curves obtained at thin silver-based mercury film electrodes deviated from theoretical predictions due to the interactions between indium, dissolved in mercury, and the silver substrate of the film electrode. At low thiocyanate ion concentrations, where the current was controlled partly by the rate of the preceding chemical step and partly by diffusion, the variations in the film thickness affected the position of the curve as predicted theoretically for the reversible diffusion controlled case.     

General characteristics of the copper-based mercury film electrode

The optimum conditions for the preparation, storage, conditioning and renewal of copper-based mercury film electrodes (CBMFEs) are given. The voltammetric results obtained at these electrodes are compared with the predictions of the theory of cyclic and stripping voltammetry at the mercury film electrode, as well as with the results obtained at the silver-based and the platinum-based mercury film electrodes. The advantage of a CBMFE is prolonged life-time, whereas the disadvantages ar the decreased range of usable positive potentials and the possibility of interfering reactions of the electrodeposited metals with the copper substrate or copper dissolved in the mercury phase. The presence of copper has no essential influence on the behaviour of lead and thallium; it affects the behaviour of zinc markedly and that of cadmium and indium slightly. The conditions allowing the minimization of the harmful action of copper on the behaviour of cadmium and indium have been found.     

Anodic stripping voltammetry with the florence mercury film electrode. determination of copper,lead and cadmium in sea water

The use of the rotating glassy carbon electrode mercury plated in situ for anodic stripping voltammetry has been investigated. The choice of electrode material is discussed. The effect of instrumental parameters on the stripping response for copper, lead and cadmium in sea water is studied, the results being in accordance with the theory of thin film electrodes. The variation in the observed sensitivity for the three metals in sea water is discussed in terms of complex-forming ligands. Lastly the performance of the film electrode is compared to that of the hanging mercury drop electrode.     

The differential pulse anodic stripping voltammetry of copper and lead and their determination in EDTA extracts of soils with the mercury film glassy carbon electrode

The differential pulse anodic stripping voltammetry of copper and lead at the mercury film glassy carbon electrode is discussed. The mercury film prevents the occurrence of a monolayer stripping peak for copper. The influence of antimony and bismuth on the anodic stripping voltammetric behaviour of copper and lead is discussed. An interaction between copper and antimony distorts the copper stripping peak and gives rise to an intermediate peak. The method described is suitable for determining copper and lead simultaneously in EDTA extracts of soils.     

Renewable silver amalgam film electrodes in electrochemical stripping analysis—a review

The success of a voltammetric sensing procedure depends mainly on the proper choice of the working electrode. This is because its ability to accumulate the analyte determines the sensitivity of the method. The main criterion of the selection of the proper working electrode is the available potential window. A variety of conductive materials have been used for the preparation of working electrodes. Of these, two kinds of mercury electrodes—hanging mercury drop and film—were used because of their excellent voltammetric performance and, in particular, their high overpotential of hydrogen reduction. The significant drawbacks of mercury electrodes, however, are the toxicity of the material and the instability of liquid mercury films. To overcome these disadvantages, less toxic mercury-containing materials have been used, such as amalgams and amalgam film electrodes. This group includes renewable silver amalgam film electrodes used for electrochemical stripping sensing purposes. These electrodes have successfully been applied for anodic, adsorptive, cathodic, catalytic voltammetric, and potentiometric stripping determination of trace amounts of inorganic cations and organic compounds in various natural matrices. In this review, the electrode design, characteristics, and application of two kinds of renewable silver amalgam film electrodes are discussed in detail.     

Anodic stripping voltammetry at a nickel-based mercury film electrode

The electrochemical properties of the nickel-based mercury film electrode (Ni-MFE) were investigated with respect to application of the electrode in the anodic stripping voltammetry (a.s.v.) of heavy metal ions. The hydrogen overpotential at the Ni-MFE is higher than those at MFEs based on other metals, and high enough to get quantitative a.s.v. peaks of lead and cadmium. The mercury film of the Ni-MFE is stable both mechanically and chemically; a.s.v. peaks at a Ni-MFE which had been used fifty times within 300 h after its preparation were identical with those at the freshly prepared electrode. With the Ni-MFE, 5 × 10^?10–10^?7 M lead(II) and 2 × 10^?10–10^?7 M cadmium(II) in the solution can be determined with relative standard deviations of 11 and 12%, respectively. These results are comparable to those obtained by a.s.v. at an in situ mercury-plated g]assy carbon electrode.     

Anodic stripping voltammetry at a mercury film electrode: baseline concentrations of cadmium,lead, and copper in selected natural waters

A simple, rapid, and inexpensive anodic stripping voltammetric method with a mercury thin film electrode is reported for the establishment of baseline concentrations of cadmium, lead, and copper in natural waters. The procedure for routine surface preparation of wax-impregnated graphite mercury film electrodes requires about 30 min. Concentrations in the 0.006–6 μg l^-1 range are determined by linear d.c. voltage sweeps; the total time for a plating and stripping cycle is 6 min or less. The need for pressure-digesting samples for copper determinations is demonstrated. The a.s.v. results correlate well with corresponding analyses performed by graphite-furnace atomic absorption spectrometry.     

Determination of heavy metals in real samples by anodic stripping voltammetry with mercury microelectrodes : Part 2. Application to Rain and Sea Waters

Differential-pulse anodic stripping voltammetry at a mercury microelectrode is applied to determine labile and total zinc, cadmium, lead and copper in samples of rain and sea water. The low ohmic drop associated with microelectrodes permits reliable measurements in rain water without addition of supporting electrolyte. The values found in a typical sample were 0.95 μg l^?1 Cu, 0.38 μg l^?1 Pb, 0.01 μg l^?1 Cd and 0.95 μg l^?1 Zn, with relative standard deviations in the range 4–18%. The small effects of organic matter at microelectrodes, compared with those at a hanging mercury drop electrode, allow sensitive and reliable measurements of labile metals in surface sea water. Total metal concentrations are determined after acidification to pH 1.5 with hydrochloric acid. The results are compared with those obtained with atomic absorption spectrometry and with differential-pulse anodic stripping voltammetry at conventional mercury electrodes. Satisfactory results were obtained for a reference sea water.     

Effect of mercury(II) on metal complex labilities determined by direct-current anodic stripping voltammetry on a thin mercury film electrode

The labilities of copper, lead and cadmium complexes with fulvic acid, nitrilotriacetic acid and an iron-humic acid colloid were studied on a preplated thin mercury film electrode and with in-situ plating of mercury on a glassy carbon electrode. In the presence of mercury(II) the apparent labilities based on direct-current anodic stripping voltammetric peak-area measurements increased for each of the cadmium and lead species and for the copper iron-humic acid colloid species. In contrast, for the copper complexes with nitrilotriacetic acid and fulvic acid the lability was not measurably altered by mercury(II); it is inferred that they do not undergo rapid metal exchange with mercury(II).     

Graphite multi-micro-disc based mercury film electrode: Comparison of experimental and theoretical anodic stripping results

an ensemble of properly distanced micro mercury film electrodes (MMFE) was used in cyclic and anodic stripping voltammetry. the experimental results were compared with the anodic stripping theory, and the agreement was found to be satisfactory. The MMFE peaks (calculated per unit area) were higher, thinner and shifted towards more negative potentials compared with the large area mercury film electrode (LAMFE) peaks.The initial graphite electrode consisted of 65 independent micro-discs forming a circle, and was prepared from carbon fibres 4.66 μm in radius. The graphite multi-micro-disc electrode was quantitatively checked in a Fe(CN)₆^3? solution under both chronoamperometric and voltammetric conditions. The deposition and oxidation of mercury is discussed also.     

Nafion-coated mercury thin film electrodes for batch-injection analysis with anodic stripping voltammetry

Batch-injection analysis exhibits the advantages of rapid and simple electroanalysis of microlitre samples. Nafion-coated mercury thin film electrodes have been evaluated for use in batch-injection analysis with anodic stripping voltammetry (BIA-ASV). The advantages of Nafion-coated electrodes in reducing electrode contamination by components of complex matrices are combined with the analysis of small microlitre sample volumes. The measurement of traces of lead and cadmium is used to illustrate the approach. An optimised procedure for formation of Nafion-coated mercury thin film electrodes is evolved. The relative sensitivity for BIA-ASV at electrodes with and without Nafion coatings is 0.9 and 0.8 for cadmium and lead respectively; detection limits are 2 x 10(-9) M and 4 x 10(-9) M. Studies were done concerning the influence of surfactants and their effect was found to be much less with the Nafion film coating. Applications to real environmental samples are demonstrated.     

Voltammetric determination of traces of silver in some metals after dissolution of the sample in mercury

The general possibility of analysing metals and alloys by dissolution of the sample in mercury and recording the anodic voltammogram is examined for the determination of silver in some metals. In order to obtain good separation of the silver peak from the anodic limit, acetonitrile is used in the supporting electrolyte. If the main component of the sample is more noble than mercury, analysis is simple and takes ? 20 min. Significant amounts of base metals in samples must be removed from the amalgam prior to the anodic stripping; optimum conditions for the removal are given. The detection limits found for the determination of silver in gold and lead and in indium amalgam are 4 × 10^?3, 4 × 10^?4 and 4 × 10^?6 % respectively. Dissolution of the lead button in mercury seems to be a successful alternative to the cupellation procedure. Silver in mercury does not form intermetallic compounds with gold.     

Comparison of physicochemical speciation procedures with metal toxicity to chlorella pyrenoidosa

Metal speciation as measured by anodic stripping voltammetry (ASV), adsorption on a resin with adsorbed hydrated aluminium oxide, and dialysis with receiving resins is compared with the toxicity of the metals to the freshwater green alga Chlorella pyrenoidosa Chick. In the presence of natural and synthetic ligands, similar labile fractions of metals were obtained for ASV at three electrodes (hanging mercury drop electrode, mercury film electrode and Nafion-coated mercury film electrode). The toxic fractions determined by ASV and bioassay were in reasonable agreement for zinc, cadmium and copper, and alteration of the analytical conditions provided some measure of agreement for lead. The resin with adsorbed hydrated aluminium oxide correlated well with bioassay for copper, but over-estimated lead toxicity and under-estimated cadmium toxicity. Dialysis with receiving resins under-estimated metal bioaccumulation in the presence of ligands. Metal speciation analysis for water samples gave higher toxic fractions for metals in samples of polluted river water and road runoff samples than those found in pristine river water.     

Voltammetric Determination of Mercury(II) at Poly(3‐hexylthiophene) Film Electrode. Effect of Halide Ions

The well‐known method for the determination of mercury(II), which is based on the anodic stripping voltammetry of mercury(II), has been adapted for applications at the thin film poly(3‐hexylthiophene) polymer electrode. Halide ions have been found to increase the sensitivity of the mercury response and shift it more positive potentials. This behavior is explained by formation of mercuric halide which can be easily deposited and stripped from the polymer electrode surface. The procedure was optimized for mercury determination. For 120 s accumulation time, detection limit of 5 ng mL^?1 mercury(II) has been observed. The relative standard deviation is 1.3% at 40 ng mL^?1 mercury(II). The performance of the polymer film studied in this work was evaluated in the presence of surfactants and some potential interfering metal ions such as cadmium, lead, copper and nickel.     

Pulsed anodic stripping voltammetry of zinc,cadmium and lead with a mercury-coated wax-impregnated graphite electrode

The use of a thin mercury-film wax-impregnated graphite electrode for the simultaneous determination of cadmium, lead and zinc in an acetate buffer by differential pulse anodic stripping voltammetry is described. Optimal instrumental parameters for maximum resolution and sensitivity for simultaneous analysis of these three elements in natural waters are discussed. The interference of copper with the determination of zinc is investigated in detail. An optimal mercury film thickness for this electrode is suggested.     

Polymer-Mercury Coated Screen-Printed Sensors for Electrochemical Stripping Analysis of Heavy Metals

In the perspective of in-field stripping analysis of heavy metals, the use and disposal of toxic mercury solutions (necessary to plate a mercury film on a carbon electrode surface) presents a problem. The aim of this work was the development of mercury coated screen-printed electrodes previously prepared in the lab and ready to use in-field. Thus some commercially available polymers like Nafion®, Eastman Kodak AQ29®, and Methocel® were investigated as mercury entrapping systems for electrochemical stripping analysis of heavy metals. Screen-printed disposable cells with a silver pseudo-reference electrode, a graphite counter electrode, and a graphite working electrode were used. To modify the sensor, the polymer solution was cast onto the carbon working electrode surface. Detection limits of 0.8 and 1 μg/L were obtained for lead and cadmium respectively. Since Methocel® based electrodes showed the best performance, they were used for the analysis of real samples. The results were compared with those obtained using a classical thin mercury film electrode and ICP spectroscopy.

All the experiments reported here were performed in un-deareated solutions as required for in-field analysis.     

Iridium Oxide Film Electrodes for Anodic Stripping Voltammetry

The new iridium oxide film electrode, applied for the determination of lead(II), cadmium(II) and copper(II) traces using differential pulse anodic stripping voltammetry (DP ASV) is presented. The electrode display an interesting stripping voltammetric performance which compares with electrodes commonly used in voltammetry. The deposited film is known as anodically electrodeposited iridium oxide film (AEIROF). The AEIROF electrode is characterized by long‐term stability (more than 40 days) and very good reproducibility of the analytical signals in this time (≤12% for 0.5 μM of lead). The regeneration of iridium film is very simple in a time shorter than 60 seconds. The effects of various factors such as: thickness of AEIROF film, preconcentration potential and time, supporting electrolyte composition, potential interferences are optimized. The detection limit for AEIROF film electrode based on glassy carbon for an accumulation time of 30 s is as low as 7 nM for lead(II). The repeatability of the method at a concentration level of the lead(II) as low as 0.5 μM, expressed as RSD is 2.5% (n=10). The proposed method was successfully applied and validated by studying certified reference material CTA‐OTL‐1. Such an attractive use of ‘mercury–free’ ‐ environmentally friendly electrodes offers great promise to measure trace metals.