Preparative isolation of arylbutanoid‐type phenol [(‐)‐rhododendrin] with peak tailing on conventional C18 column using middle chromatogram isolated gel column coupled with reversed‐phase liquid chromatography

Reversed‐phase liquid chromatography coupled with middle chromatogram isolated gel column was employed for the efficient preparative separation of the arylbutanoid‐type phenol [(‐)‐rhododendrin] from Saxifraga tangutica. Universal C18 (XTerra C18) and XCharge C18 columns were compared for (‐)‐rhododendrin fraction analysis and preparation. Although tailing and overloading occurred on the XTerra C18 column, the positively charged reversed‐phase C18 column (XCharge C18) overcame these drawbacks, allowing for favorable separation resolution, even when loading at a on a preparative scale (3.69 mg per injection). The general separation process was as follows. First, 365.0 mg of crude (‐)‐rhododendrin was enriched from 165 g Saxifraga tangutica extract via a middle chromatogram isolated gel column. Second, separation was performed on an XTerra C18 preparative column, from which 73.8 mg of the target fraction was easily obtained. Finally, the 24.0 mg tailing peak of (‐)‐rhododendrin on XTerra C18 column was selectively purified on the XCharge C18 analytical column. These results demonstrate that the tailing nonalkaloid peaks can be effectively used for preparative isolation on XCharge C18 columns.     

An automated food protein isolation approach on preparative scale by two‐dimensional liquid chromatography with active modulation interface

In this work, an automated 2D‐LC approach for protein isolation from egg samples on preparative scale is proposed. The method is based on the use of a C18 guard column installed in a switching valve to focus the proteins coming from the first dimension column, before their elution in the second column. For the first dimension separation, a size‐exclusion column, packed with 3 μm ultrapure silica particles was used. An RP column based on core‐shell technology was used for the second dimension separation. A standard mixture of BSA, β‐lactoglobulin, and glucose oxidase, chosen as a protein model system, was used to optimize the chromatographic separation conditions. The fully automated workflow allowed to isolate, in a single‐chromatographic analysis, a protein amount of 50 μg for each peak fraction, with a total time of 15 min for the first separation and additional 30 min of the second separation for each trapped protein. The final aim was the development of proper analytical tools for protein isolation from foodstuffs to be used for the molecular identification by MS, as well as for biotherapeutic uses, allergy testing, and large‐scale investigations in biological systems.     

Simultaneous separation and determination of thallium in water samples by high‐performance liquid chromatography with inductively coupled plasma mass spectrometry

An analytical method for separation and determination of thallium species in water using high‐performance liquid chromatography with inductively coupled plasma mass spectrometry was developed. The composition and concentration of mobile phase, injection volume, and pH value were optimized respectively with an anion or cation exchange column. The results showed that Tl(I) and Tl(III) were effectively separated using anion exchange column Hamilton PRP‐X100, with the mobile phase consisting of 200 mmol/L ammonium acetate and 10 mmol/L diethylenetriaminepentaacetic acid (pH = 4.2). When using a Dionex cation exchange guard column, CS12A, 15 mmol/L HNO₃, and 3 mmol/L diethylenetriaminepentaacetic acid as the mobile phase, Tl(I) and Tl(III) could be effectively separated. The detection limits of the methods were 3–6 and 9–12 ng/L, respectively. In a solution containing Fe ions and oxalic acid, a significant quantity of Tl(I) was oxidized. Fe ions and oxalic acid in the water samples did not interfere with high‐performance liquid chromatography‐inductively coupled plasma mass spectrometry measurement results.     

Development of a liquid chromatography–tandem mass spectrometry method for simultaneous determination of five isoflavonoids and seven neurochemicals in rat brain dialysate and its application to a pharmacological study

Pueraria lobata is a medicinal plant widely used in traditional Chinese medicine. The total pueraria isoflavones have demonstrated positive effect against neurological disorders. In the present study, we first develop an ultra high performance liquid chromatography and tandem mass spectrometry method to quantify the multiple active pueraria isoflavonoids and neurochemical markers in brain dialysate to provide tools for further exploring the functional mechanism of pueraria isoflavones for neuroactivities. A phenomenex Luna C18 column (50 × 2.0 mm, 5 μm) was employed with acetonitrile/0.05% formic acid in water as the mobile phase for the separation of analytes. A mass spectrometer with electrospray ionization source in positive/negative ion switching mode was used for multiple reaction monitoring of the detected compounds. The method was validated and proved acceptable. The intra‐ and interday precision across quality control levels was within 13.87 for all analytes, whereas the deviation of assay accuracies ranged between 0.03 and 11.53%. The method was successfully applied to a pharmacological study of pueraria isoflavones in rat brain.     

Ionic‐liquid‐based ultrasound‐assisted extraction of isoflavones from Belamcanda chinensis and subsequent screening and isolation of potential α‐glucosidase inhibitors by ultrafiltration and semipreparative high‐performance liquid chromatography

The separation of a compound of interest from its structurally similar homologues to produce high‐purity natural products is a challenging problem. This work proposes a novel method for the separation of iristectorigenin A from its structurally similar homologues by ionic‐liquid‐based ultrasound‐assisted extraction and the subsequent screening and isolation of potential α‐glucosidase inhibitors via ultrafiltration and semipreparative high‐performance liquid chromatography. Ionic‐liquid‐based ultrasound‐assisted extraction was successfully applied to the extraction of tectorigenin, iristectorigenin A, irigenin, and irisflorentin from Belamcanda chinensis . The optimum conditions for the efficient extraction of isoflavones were determined as 1.0 M 1‐ethyl‐3‐methylimidazolium tetrafluoroborate with extraction time of 30 min and a solvent to solid ratio of 30 mL/g. Ultrafiltration with liquid chromatography and mass spectrometry was applied to screen and identify α‐glucosidase inhibitors from B. chinensis , followed by the application of semipreparative high‐performance liquid chromatography to separate and isolate the active constituents. Four major compounds including tectorigenin, iristectorigenin A, irigenin, and irisflorentin were screened and identified as α‐glucosidase inhibitors, and then the four active compounds abovementioned were subsequently isolated by semipreparative high‐performance liquid chromatography (99.89, 88.97, 99.79, and 99.97% purity, respectively). The results demonstrate that ionic liquid extraction can be successfully applied to the extraction of isoflavones from B. chinensis .     

Temperature‐programmed multicapillary gas chromatograph microcolumn for the analysis of odorous sulfur pollutants

We report the fabrication and performance of a silicon‐on‐glass micro gas chromatography eight‐capillary column based on microelectromechanical systems technology that is 50 cm long, 30 μm wide, and 300 μm deep. According to the theory of a gas chromatography column, an even gas flow among different capillaries play a vital role in the peak broadening. Thus, a flow splitter structure is designed by the finite element method through the comparison of the velocity distributions of the eight‐capillary columns with and without splitter as well as an open tubular column. The simulation results reveal that eight‐capillary column with flow splitters can receive more uniform flow velocity in different capillaries, hence decreases the peak broadening and in turn increases the separation efficiency. The separation experiment results show that the separation efficiency of about 22 000 plates/m is achieved with the chip column temperature programmed for analysis of odorous sulfur pollutants. This figure is nearly two times higher than that of the commercial capillary column coated the similar stationary phase. And the separation time of all the components in the microcolumn is less than 3.8 min, which is faster than the commercial capillary column.     

One‐pot preparation of mercaptotetrazole‐silica hybrid monoliths by the thiol‐ene click reaction for mixed‐mode capillary liquid chromatography

A novel mercaptotetrazole‐silica hybrid monolithic column was prepared for capillary liquid chromatography, in which the thiol‐end mercaptotetrazole was mixed with hydrolyzed γ‐methacryloxypropyltrimethoxysilane and tetramethyloxysilane for the co‐polycondensation and thiol‐ene click reaction in a one‐pot process. The effects of the molar ratio of silanes, the amount of mercaptotetrazole, and the volume of porogen on the morphology, permeability and pore properties of the as‐prepared mercaptotetrazole‐silica hybrid monoliths were investigated in detail. A series of test compounds including alkylbenzenes, amides and anilines were employed for evaluating the retention behaviors of the mercaptotetrazole‐silica hybrid monolithic columns. The results demonstrated that the mercaptotetrazole‐silica hybrid monoliths exhibited hydrophobic, hydrophilic as well as ion‐exchange interaction. The run‐to‐run, column‐to‐column and batch‐to‐batch reproducibilities of the mercaptotetrazole‐silica hybrid monoliths were satisfactory with the relative standard deviations less than 1.4 (n  = 5), 3.9 (n  = 3) and 4.0% (n  = 5), respectively. In addition, the mercaptotetrazole‐silica hybrid monolith was further applied to the separation of sulfonamides, nucleobases and protein tryptic digests. These successful applications confirmed the promising potential of the mercaptotetrazole‐silica hybrid monolith in the separation of complex samples.     

Open-tubular nanoelectrochromatography (OT-NEC): gel-free separation of single stranded DNAs (ssDNAs) in thermoplastic nanochannels

Electrophoresis or electrochromatography carried out in nanometer columns (width and depth) offers some attractive benefits compared to microscale columns. These advantages include unique separation mechanisms that are scale dependent, fast separation times, and simpler workflow due to the lack of a need for column packing and/or wall coatings to create a stationary phase. We report the use of thermoplastics, in this case PMMA, as the substrate for separating single-stranded DNAs (ssDNAs). Electrophoresis nanochannels were created in PMMA using nanoimprint lithography (NIL), which can produce devices at lower cost and in a higher production mode compared to the fabrication techniques required for glass devices. The nanochannel column in PMMA was successful in separating ssDNAs in free solution that was not possible using microchip electrophoresis in PMMA. The separation could be performed in <1 s with resolution >1.5 when carried out using at an electric field strength of 280 V/cm and an effective column length of 60 μm (100 nm × 100 nm, depth and width). The ssDNAs transport through the PMMA column was driven electrokinetically under the influence of an EOF. The results indicated that the separation was dominated by chromatographic effects using an open tubular nano-electrochromatography (OT-NEC) mode of separation. Interesting to these separations was that no column packing was required nor a wall coating to create the stationary phase; the separation was affected using the native polymer that was UV/O₃ activated and an aqueous buffer mobile phase.     

Cryogenic modulation fast GC × GC–MS using a 10 m microbore column combination: Concept,method optimization,and application

The present research is based on the concept of using a 10 m × 0.1 mm id column for cryogenic‐modulation fast comprehensive two‐dimensional gas chromatography with quadrupole mass spectrometry. Specifically, an 8.9 m × 0.1 mm id low‐polarity column was used as the first dimension, and a 1.1 m × 0.1 mm id medium‐polarity column was used as the second dimension. The main scope of the investigation was to develop a high peak‐capacity method, with an analysis time of approximately 10 min. Various aspects related to method optimization are discussed, as well as separation parameters such as peak capacity (in each dimension, and as a total value), first‐dimension sample capacity, peak widths, modulation ratio, sensitivity enhancement, and number of spectra per peak. The fast approach was evaluated in applications involving a mixture of cosmetic allergens and a sample of perfume. The approach proposed enables high‐resolution separations in a short time (across the C₈–C₂₃ alkane range), as well as a considerable reduction of the consumption of gases for modulation cooling and heating.     

Styrene‐N‐phenylacrylamide co‐polymer modified silica monolith particles with an optimized mixing ratio of monomers as a new stationary phase for the separation of peptides in high performance liquid chromatography

A stationary phase was prepared by chemical derivatization of the support particles with a layer of copolymer composed of styrene and N‐phenyl acrylamide. Silica monolith particles of ca. 2.6 µm (volume‐based average) have been prepared as the support particles by sol‐gel reaction followed by differential sedimentation. The particles were reacted with 3‐chloropropyl trimethoxysilane followed by sodium diethyldithiocarbamate to introduce an initiator moiety. Then, the copolymer layer was immobilized via reversible addition‐fragmentation transfer polymerization. The resultant phase was packed in glass‐lined stainless‐steel micro‐columns (1 x 150 mm) and evaluated for the separation of a mixture composed of five peptides (Trp‐Gly, Thr‐Tyr‐Ser, angiotensin I, isotocin and bradykinin). The effect of monomer mixing ratio (styrene versus N‐phenyl acrylamide) on the chromatographic separation efficiency of the stationary phase was examined. A number of theoretical plates (N) as high as 33 600 plates/column (224 000 plates/m, 4.46 µm plate height) was achieved using the column packed with the optimized stationary phase. The column‐to‐column reproducibility based on three columns packed with three different batches of stationary phase was found satisfactory in separation efficiency, retention factor, and asymmetry factor.     

Open tubular capillary column of 50 μm internal diameter with a very high separation efficiency for the separation of peptides in CEC and LC

A specially designed long open tubular capillary column (50 μm internal diameter and 112 cm effective length) was prepared by fabrication of a thin three‐component co‐polymer layer on the inner surface of silica capillary. A pretreated silica capillary was reacted with 4‐(chloromethyl)phenyl isocyanate in the presence of dibutyltin dichloride as catalyst followed by sodium diethyl dithiocarbamate. Then a thin polymer layer was made on the inner surface of capillary by reversible addition‐fragmentation transfer polymerization of styrene, N‐phenylacrylamide, and methacrylic acid. A carefully adjusted formulation of reaction mixture and elaborated procedures were adopted to secure formation of the co‐polymer layer of enhanced separation performance. The co‐polymer immobilized open tubular capillary column was used for the separation of a synthetic mixture of five peptides and excellent separation efficiency (over 1.7 million per column) was obtained in the capillary electrochromatography mode. Such excellent separation efficiencies of ca. 1 m column have not been obtained in the isocratic elution mode so far. The column was also used for separation of the peptides in the liquid chromatography mode to show very good separation efficiency (average 286 700 per column).     

Enantioseparation of aromatic amino acids using CEC monolith with novel chiral selector,N‐methacryloyl‐l‐histidine methyl ester

A new type of polymethacrylate‐based monolithic column with chiral stationary phase was prepared for the enantioseparation of aromatic amino acids, namely d ,l ‐phenylalanine, d ,l ‐tyrosine, and d ,l ‐tryptophan by CEC. The monolithic column was prepared by in situ polymerization of butyl methacrylate (BMA), N‐methacryloyl‐l ‐histidine methyl ester (MAH), and ethylene dimethacrylate (EDMA) in the presence of porogens. The porogen mixture included DMF and phosphate buffer. MAH was used as a chiral selector. FTIR spectrum of the polymethacrylate‐based monolith showed that MAH was incorporated into the polymeric structure via in situ polymerization. Some experimental parameters including pH, concentration of the mobile phase, and MAH concentration with regard to the chiral CEC separation were investigated. Single enantiomers and enantiomer mixtures of the amino acids were separately injected into the monolithic column. It was observed that l ‐enantiomers of aromatic amino acids migrated before d ‐enantiomers. The reversal enantiomer migration order for tryptophan was observed upon changing of pH. Using the chiral monolithic column (100 μm id and 375 μm od), the best chiral separation was performed in 35:65% ACN/phosphate buffer (pH 8.0, 10 mM) with an applied voltage of 12 kV in CEC. SEM images showed that the chiral monolithic column has a continuous polymeric skeleton and large through‐pore structure.     

Hydrophobic ionic liquid modified thermoresponsive molecularly imprinted monolith for the selective recognition and separation of tanshinones

A hydrophobic ionic liquid modified thermoresponsive molecularly imprinted monolith was synthesized using N‐isopropylacrylamide as a thermoresponsive monomer and a long‐chain hydrophobic ionic liquid as an auxiliary modification monomer. The ionic‐liquid‐modified thermoresponsive molecularly imprinted polymer was characterized by scanning electron microscopy and Fourier transform infrared spectroscopy. When the column temperature was 50°C, the synthesized monolithic column was successfully applied to the selective separation of homologue tanshinones within 7 min and eluted only by water (mobile phase) (theoretical plates more than 1.00 × 10⁵ per meter). The negative Gibbs free energy (≤–2.37) values showed that the transfer of the tanshinones from the mobile phase to the stationary phase on this monolithic column was a thermodynamically spontaneous process. Good linearity of the five tanshinones by thermoresponsive monolith was obtained in the range of 0.100–25.0 μg/mL. The limit of detection (S/N = 3) and limit of quantitation (S/N = 10) were less than 0.0390 and 0.0630 μg/mL, respectively, with a relative standard deviation of <4.8%. In this proposed thermoresponsive chromatography method, the separation of homologue analytes can be achieved by changing the column temperature, and the use of water as the mobile phase would decrease the economic cost and organic pollution.     

The fabrication of poly (polyethylene glycol diacrylate) monolithic porous layer open tubular (mono‐PLOT) columns and applications in hydrophilic interaction chromatography and capillary gas chromatography for small molecules

The easy shrinkage and swelling of polymer monolithic column when exposed to mobile phase with different polarity is a problem that cannot be ignored. To overcome this drawback, a convenient aqueous two‐phase polymerization approach was used to prepare poly (polyethylene glycol diacrylate, PEGDA) monolithic porous layer open tubular (mono‐PLOT) columns (150 μm). The poly(PEGDA) mono‐PLOT column with homogeneous polymer porous layer was synthesized successfully. A maximum plate number of 41,500 plates per meter for allyl thiourea was obtained under a velocity of 1.8 mm/s. Several kinds of polar molecule were separated on the proposed mono‐PLOT column and a typical hydrophilic interaction retention mechanism was observed. High speed separation of benzoic acids was also carried out, baseline separation of five benzoic acids was successfully achieved within 5 min with a 70 cm mono‐PLOT column at 50°C. Furthermore, the resulting PLOT column was also successfully applied to separate standard analytes of three DNA oxidative damage products and RNA‐modified nucleosides and four chlorophenols. At last, the column could separate alcohols, alkanes, and aromatic isomers via GC. It had more than 20,000 plates per meter for butanol – higher than commercial coatings open tubular columns.     

Separation and purification of two taxanes and one xylosyl‐containing taxane from Taxus wallichiana Zucc.: A comparison between high‐speed countercurrent chromatography and reversed‐phase flash chromatography

10‐Deacetylbaccatin III, an important semisynthetic precursor of paclitaxel and docetaxel, can be extracted from Taxus wallichiana Zucc. A process for the isolation and purification of 10‐deacetylbaccatin III ( 1 ), baccatin III ( 2 ), and 7β‐xylosyl‐10‐deacetyltaxol ( 3 ) from the leaves and branches of Taxus wallichiana Zucc. via macroporous resin column chromatography combined with high‐speed countercurrent chromatography or reversed‐phase flash chromatography was developed in this study. After fractionation by macroporous resin column chromatography, 80% methanol fraction was selected based on high‐performance liquid chromatography and liquid chromatography with mass spectrometry qualitative analysis. A solvent system composed of n‐hexane, ethyl acetate, methanol, and water (1.6:2.5:1.6:2.5, v/v/v/v) was used for the high‐speed countercurrent chromatography separation at a flow rate of 2.5 mL/min. The reversed‐phase flash chromatography separation was performed using methanol/water as the mobile phase at a flow rate of 3 mL/min. The high‐speed countercurrent chromatography separation produced compounds 1 (10.2 mg, 94.4%), 2 (2.1 mg, 98.0%), and 3 (4.6 mg, 98.8%) from 100 mg of sample within 110 min, while the reversed‐phase flash chromatography separation purified compounds 1 (9.8 mg, 95.6%) and 3 (4.9 mg, 97.9%) from 100 mg of sample within 120 min.     

An optimized mixed‐mode stationary phase based on silica monolith particles for the separation of peptides and proteins in high‐performance liquid chromatography

A phase with both hydrophobic and hydrophilic functionalities has been synthesized by modification of ground silica monolith particles with C18 and 1‐[3‐(trimethoxysilyl)propyl] urea ligands. A series of phases was prepared by changing the ratio of the two ligands to determine the optimal ratio in view of separation efficiency. The resultant optimized stationary phase was packed in narrow‐bore glass‐lined stainless‐steel columns (1 × 300 mm and 2.1 × 100 mm) and used for the separation of synthetic peptides and proteins. The average numbers of theoretical plates (N) of 52 100/column (174 000/m, 5.75 µm plate height) and 35 500/column (118 000/m, 8.47 µm plate height) were achieved with the 300 mm column at a flow rate of 25 µL/min (0.86 mm/s) in 60:40 v/v acetonitrile/30 mM aqueous ammonium formate for the mixture of peptides (Thr‐Tyr‐Ser, Val‐Ala‐Pro‐Gly, angiotensin I, isotocin, and bradykinin) and for the mixture of proteins (myoglobin, human serum albumin, and insulin), respectively. Fast analysis of the peptides and proteins was also carried out at a flow rate of 0.9 mL/min (6.88 mm/s) with the 100 mm column and all the analytes were eluted within 2 min with good separation efficiency.     

Ionic liquids as mobile phase additives for determination of thiocyanate and iodide by liquid chromatography

An analytical method was developed for the simultaneous determination of thiocyanate and iodide by reversed‐phase liquid chromatography with UV detection using imidazolium ionic liquids as mobile phase additives. The chromatographic behaviors of the two anions on a C₁₈ column were studied and compared with four types of reagents including imidazolium ionic liquids, pyridinium ionic liquids, 4‐aminophenol hydrochloride and tetrabutylammonium as mobile phase additives. The effects of the concentrations of imidazolium ionic liquids, organic solvents and detection wavelength on separation and detection of the anions were investigated. The role of ionic liquids, retention rules and mechanisms were discussed. The separation of the anions was performed on the C₁₈ reserved‐phase column using acetonitrile‐0.3 mmol/L 1‐amyl‐3‐methylimidazolium tetrafluoroborate (10:90, v/v) as mobile phase, with column temperature of 35°C, flow rate of 1 mL/min and detection wavelength of 210 nm. Under these conditions, the two anions can be completely separated within 6 min. The limits of detection were 0.05 mg/L. The method was applied for the determination of thiocyanate and iodide in ionic liquid samples and iodide drugs, and the spiked recoveries ranged from 97 to 101%. The method is simple, accurate and meets the requirements of quantitative analysis for thiocyanate and iodide.     

Determination of betaine,l‐carnitine,and choline in human urine using a self‐packed column and column‐switching ion chromatography with nonsuppressed conductivity detection

A simple method for the determination of betaine, l ‐carnitine, and choline in human urine was developed based on column‐switching ion chromatography coupled with nonsuppressed conductivity detection by using a self‐packed column. A pretreatment column (50 mm × 4.6 mm, id) packed with poly(glycidyl methacrylate‐divinylbenzene) microspheres was used for the extraction and cleanup of analytes. Chromatographic separation was achieved within 10 min on a cationic exchange column (150 mm × 4.6 mm, id) using maleic anhydride modified poly(glycidyl methacrylate‐divinylbenzene) as the particles for packing. The detection was performed by ion chromatography with nonsuppressed conductivity detection. Parameters including column‐switching time, eluent type, flow rates of eluent, and interfering effects were optimized. Linearity (r ² ≥ 0.99) was obtained for the concentration range of 0.50–100, 0.75–100, and 0.25–100 μg/mL for betaine, l ‐carnitine, and choline, respectively. Detection limits were 0.12, 0.20, and 0.05 μg/mL for betaine, l ‐carnitine, and choline, respectively. The intra‐ and interday accuracy and precision for all quality controls were within ±10.11%. Satisfactory recovery was observed between 92.5 and 105.0%. The validated method was successfully applied for the determination of betaine, l ‐carnitine, and choline in urine samples from healthy people.     

Hansen solubility parameters for assay method optimization of simvastatin,ramipril, atenolol,hydrochlorothiazide and aspirin in human plasma using liquid chromatography with tandem mass spectrometry

A simple, specific, sensitive, validated method was developed using liquid chromatography with tandem mass spectrometry with electrospray ionization of human plasma for the simultaneous estimation of drugs (simvastatin, ramipril, atenolol, hydrochlorothiazide, and aspirin) of Polycap^TM capsule used in cardiovascular therapy. The interaction of these actives including internal standards between the stationary and mobile phase were investigated using Hansen solubility parameters. Chromatographic separation was performed on Phenomenex Synergi Polar‐RP (30 × 2 mm, 4 μm) column with a gradient mobile phase composition of acetonitrile and 5 mM ammonium formate for positive mode and 0.1% formic acid in both water and acetonitrile for negative mode. The flow rate and runtime were 1.0 mL/min and 3.5 min, respectively. Sample extraction was done by protein precipitation using acetonitrile, enabling a fast analysis. The calibration ranges from 0.1 to 100, 0.1 to 100, and 1 to 1000 ng/mL for simvastatin, ramipril, and atenolol using internal standard carbamazepine in positive mode, respectively, whereas it was 0.3–300 and 2–2000 ng/mL for hydrochlorothiazide and aspirin using internal standard 7‐hydroxy coumarin in negative mode, respectively. Hansen solubility parameters can be used as a high‐throughput optimizing tool for column and mobile phase selection in bioanalysis. This validated bioanalytical method has the potential for future fixed dose combination based preclinical and clinical studies that can save analysis time.     

Separation of selenium species and their sensitive determination in rice samples by ion‐pairing reversed‐phase liquid chromatography with inductively coupled plasma tandem mass spectrometry

A highly sensitive method was developed for the simultaneous separation and determination of organic and inorganic selenium species in rice by ion‐pairing reversed‐phase chromatography combined with inductively coupled plasma tandem mass spectrometry. To achieve a good separation of these species, a comparison between anion‐exchange chromatography and ion‐pairing reversed‐phase chromatography was performed. The results indicated that ion‐pairing reversed‐phase chromatography was more suitable due to better separation and higher sensitivity for all analytes. In this case, a StableBond C18 column proved to be more robust or to have a better resolution than other C18 columns, when 0.5 mM tetrabutylammonium hydroxide and 10 mM ammonium acetate at pH 5.5 were used as the mobile phase. Moreover, an excellent sensitivity was obtained in terms of interferences by means of tandem mass spectrometry in the hydrogen mode. The detection limits were 0.02–0.12 μg/L, and recoveries of five selenium species were 75–114%, with relative standard deviations ≤ 9.4%. This method was successfully applied to the analysis of rice samples. Compared with previous studies, the proposed method not only gave comparable results when used for measuring selenium‐enriched rice, but it can provide greater sensitivity for the detection of low concentrations of selenium species in rice.