A Novel Fluorescent Cesium Ion-Selective Optode Membrane based on 15-Crown-5-Anthracene

An optode system based on a plasticized polymer membrane containing cesium ion-selective fluoroionophore and lipophilic anions for the determination of cesium ions has been developed. In this work, 15-crown-5 derivative including anthracene was used as a fluoroionophore. Emission intensity of the optode membrane incorporating 15-crown-5-anthracene was measured at 500 nm with excitation at 360 nm in the presence of Tris-HCl buffer solution. Under optimum experimental condition, the relative fluorescence intensity was linear with the concentration of cesium ion in the range of 1.0 × 10^-4 M to 1.0 × 10^-1 M and the detection limit was obtained 4.2 × 10^-5 M, as defined by LOD = 3 × S_b/m (where S_b=standard deviation of blank signal and, m=slope of the calibration curve). The effect of pH of sample solution on the fluorescent response, the selectivity, response time and reproducibility of the optode membrane were also discussed. The fluorescent optode system shows a high selectivity and sensitivity for cesium ion with respect to other cations such as K⁺, Na⁺ and Li⁺.     

Preparation and Characterization of CdHgTe Nanoparticles and Their Application on the Determination of Proteins

CdHgTe nanoparticles (NPs) with the emission in the near-infrared regions were prepared in aqueous solution, and were characterized by transmission electron microscopy, X-ray diffraction spectrometry, spectrofluorometry and ultraviolet-visible spectrometry. Based on the fluorescence quenching of CdHgTe NPs in the presence of proteins, a novel method for the determination of proteins with CdHgTe NPs as a near-infrared fluorescence probe was developed. Maximum fluorescence quenching was observed with the excitation and emission wavelengths of 500 and 693 nm, respectively. Under the optimal conditions, the calibration graphs were linear in the range of 0.04 × 10⁻⁶–5.6 × 10⁻⁶ g ml⁻¹ for lysozyme (Lyz) and 0.06 × 10⁻⁶–6.1 × 10⁻⁶ g ml⁻¹ for bovine hemoglobin (BHb), respectively. The limits of detection were 13 ng ml⁻¹ for Lyz and 27 ng ml⁻¹ for BHb, respectively. Four synthetic samples were determined and the results were satisfied.     

Fluorescence Enhancement of the Silver Nanoparticales – Curcumin - Cetyltrimethylammonium Bromide-nucleic Acids System and its Analytical Application

It is found that silver nanoparticles (AgNPs) can further enhance the fluorescence intensity of curcumin (CU) - cetyltrimethylammonium bromide (CTAB) – nucleic acids and improve its anti-photobleaching activity. Under optimum conditions, the enhanced fluorescence intensity is proportion to the concentration of nucleic acids in the range of 2.0 × 10⁻⁸–1.0 × 10⁻⁶ g mL⁻¹ for fish sperm DNA (fsDNA), 2.0 × 10⁻⁸–1.0 × 10⁻⁶ g mL⁻¹ for calf thymus DNA (ctDNA), 1.0 × 10⁻⁸–1.0 × 10⁻⁶ g mL⁻¹ for yeast RNA (yRNA), and their detection limits (S/N = 3) are 8.0 ng mL⁻¹, 10.5 ng mL⁻¹ and 5.8 ng mL⁻¹, respectively. This method is used for determining the concentration of DNA in actual sample with satisfactory results. The interaction mechanism is also studied.     

Binding of Quercetin to Lysozyme as Probed by Spectroscopic Analysis and Molecular Simulation

The binding of quercetin to lysozyme (LYSO) in aqueous solution was investigated by fluorescence spectroscopy, UV-vis absorption spectroscopy and molecular simulation at pH 7.4. The fluorescence quenching of LYSO by addition of quercetin is due to static quenching, the binding constants, K _a , were 3.63 × 10⁴, 3.31 × 10⁴ and 2.85 × 10⁴ L·mol⁻¹ at 288, 298 and 308 K, respectively. The thermodynamic parameters, enthalpy change, ∆H, and entropy change, ∆S, were noted to be −7.56 kJ·mol⁻¹ and 61.07 J·mol⁻¹·K⁻¹. The results indicated that hydrophobic interaction may play a major role in the binding process. The distance r between the donor (LYSO) and acceptor (quercetin) was determined as 3.34 nm by the fluorescence resonance energy transfer. The synchronous fluorescence spectroscopy showed the polarity around the tryptophan residues increased and the hydrophobicity decreased. Furthermore, the study of molecular simulation indicated that quercetin could bind to the active site (a pocket made up of 24 amino-acid residues) of LYSO mainly via hydrophobic interactions and that there were hydrogen interactions between the residues (Gln 57, Ile 98) of LYSO and quercetin. The accessible surface area (ASA) calculation verified the important roles of tryptophan (Trp) residues during the binding process.     

Terbium Sensitized Luminescence for the Determination of Ketoprofen in Pharmaceutical Formulations

This paper explores an ultra-sensitive luminescence method for the determination of Ketoprofen (KP) in pharmaceutical formulations. The technique is indirect and exploits the luminescence enhancement of terbium (Tb³⁺) by complexation with KP (Tb³⁺–KP), which was monitored at respective excitation and emission wavelengths of λ _ex = 258 nm and λ _em = 549 nm. The effect of varying the Tb³⁺ concentration and using multiple solvents was examined to determine optimal experimental conditions. Maximum sensitization was accomplished in the presence of methanol where the most favourable condition for the formation of the complex was recorded at a level of 1.0 × 10⁻⁵ M of Tb³⁺. Under these optimum experimental conditions, linear calibration curve was obtained in the range of 2.8 × 10⁻⁷–3.1 × 10⁻⁶ M with a detection limit of 8.7 × 10⁻⁸ M. The technique was validated with ‘working’ reference standards and produced relative standard deviations < 2% indicating that the reproducibility was highly acceptable. The proposed method was successfully applied to assays of KP in pharmaceutical formulations with average recoveries of 92–98%. The results were found to be in good agreement with those obtained by HPLC. The method is highly suited for general applications of this nature.     

Fluorescent Method for the Determination of Sulfide Anion with ZnS:Mn Quantum Dots

Water-soluble Mn²⁺-doped ZnS quantum dots (QDs) were prepared using mercaptoacetic acid as the stabilizer. The optical properties and structure features were characterized by X-Ray, absorption spectrum, IR spectrum and fluorescence spectrum. In pH 7.8 Tris-HCl buffer, the QDs emitted strong fluorescence peaked at 590 nm with excitation wavelength at 300 nm. The presence of sulfide anion resulted in the quenching of fluorescence and the intensity decrease was proportional to the S²⁻ concentration. The linear range was from 2.5 × 10⁻⁶ to 3.8 × 10⁻⁵ mol L⁻¹ with detection limit as 1.5 × 10⁻⁷ mol L⁻¹. Most anions such as F⁻, Cl⁻, Br⁻, I⁻, CH₃CO₂ ⁻, ClO₄ ⁻, CO₃ ²⁻, NO₂ ⁻, NO₃ ⁻, S₂O₃ ²⁻, SO₃ ²⁻ and SO₄ ²⁻ did not interfere with the determination. Thus a highly selective assay was proposed and applied to the determination of S²⁻ in discharged water with the recovery of ca. 103%.     

Interaction of Thyroxine with 7 Hydroxycoumarin: A Fluorescence Quenching Study

The interaction between thyroxine hormone and 7 hydroxycoumarin (7HC) was investigated using fluorescence quenching method. The experimental results showed that thyroxine could quench the fluorescence of 7HC by forming the 7HC–thyroxine complex with static quenching. The apparent binding constants (K) between 7HC and thyroxine were determined to be 1.51 × 10⁴ (297 K) and 9.06 × 10³ (310 K). The binding sites (n) 0.98 ± 0.1. The thermodynamic parameters showed that the interaction between 7HC and thyroxine was driven mainly by hydrogen bonding interactions and van der Waals force. Calibration for thyroxine, based on quenching titration data, was linear in the concentration range 2.0 × 10⁻⁸ to 3.0 × 10⁻⁷ mol/l. The relative standard deviation was 2.58% for 2.0 × 10⁻⁷ mol/l thyroxine (n = 4) and the 3σ limit of detection was 3.42 × 10⁻⁸ mol/l in cationic surfactant CTAB medium.     

Study of Enhanced Chemiluminescence of Diperiodatocuprate (III) on 1,10-Phenanthroline/Hydrogen Peroxide/Cetyltrimethylammonium Bromide System

In the paper, a chemiluminescence (CL) system was developed based on the catalytical effect of diperiodatocuprate (III) (DPC) on the 1,10-phenanthroline (phen)/hydrogen peroxide (H₂O₂) in the presence of cetyltrimethylammonium bromide (CTAB). The effects of experimental conditions were investigated. Meanwhile the increase of CL intensity of the DPC/phen/H₂O₂/CTAB system is proportional to the concentration of phen in the range of low concentration. The linear range of the calibration curve is 5.0 × 10⁻⁹–1.0 × 10⁻⁶ mol L⁻¹, and the corresponding detection limit is 1.9 × 10⁻⁹ mol L⁻¹. The effects of phenolic compounds (PCs) on the system were investigated. Hydroquinone was used as an example to investigate the application of the CL system to the determination of PCs. The quenched CL intensity is linearly related to the logarithm of concentration of hydroquinone. The linear range of the calibration curve is 2.5 × 10⁻⁹–1.0 × 10⁻⁵ g mL⁻¹, and the corresponding detection limit is 1.8 × 10⁻⁹ g mL⁻¹. This phen and hydroquinone can be synchronously determined. The method was applied to the determination of hydroquinone in water samples and the recoveries were from 92% to 106%.     

Spectrofluorimetric Determination of Coumarin in Commercial Tablets

A simple, rapid and effective analytical method based on fluorescence spectroscopy for the determination of coumarin in pharmaceutical formulations without pre-treatment or pre-concentration step was development. Coumarin had maximum excitation and emission at 310 nm and 390 nm, respectively. Optimum conditions for the detection of coumarin were investigated. Under optimized conditions, we observed a linear behavior for the sign of coumarin in the concentration range of 2.5 × 10⁻⁶ to 1.0 × 10⁻⁴ mol L⁻¹, with linearity of 0.998 and sensitivity of 2.9 × 10¹⁰ u.a/mol L⁻¹. The proposed method was validated in terms of accuracy, precision and specificity of coumarin using the standard addition and external calibration. It was noted that the results support (P < 0.05), indicating that the matrices were not an interference in the determination of coumarin by fluorescence spectroscopy. The results were favorable compared with those obtained by reference chromatographic methods.     

Fluorescence Enhancement Effect for the Determination of Polychlorinated Biphenyls with Bovine Serum Albumin

A sensitive and selective method for the trace determination of 3, 3’, 4, 4’-tetrachlorobiphenyl (PCB77) by using bovine serum albumin (BSA) as a fluorescence probe was introduced. Under optimum conditions, the enhanced fluorescence intensity was proportional to the concentration of polychlorinated biphenyls in the range of 8.9 × 10⁻⁸–5.0 × 10⁻⁶ mol L⁻¹ for PCB77, and 5.0 × 10⁻⁷–5.0 × 10⁻⁶ mol L⁻¹ for 2, 2’, 5, 5’-tetrachlorbiphenyl (PCB52). The detection limits (S/N = 3) of PCB77 and PCB52 were 2.6 × 10⁻⁸ mol L⁻¹ and 2.9 × 10⁻⁷ mol L⁻¹, respectively. Furthermore, the fluorescence enhancement mechanism was discussed in detail. Results indicated that fluorescence enhancement of the system originated from the formation of BSA-PCBs complexes. In addition, PCBs were mainly bound to the tyrosine residues in BSA molecules.     

Determination of Paracetamol Based on its Quenching Effect on the Photoluminescence of CdTe Fluorescence Probes

L-Cysteine capped CdTe nanoparticles (NPs) were synthesized in aqueous medium, and their application as fluorescence probes in the determination of paracetamol was studied. The L-cysteine capped CdTe NPs were characterized by transmission electron microscopy, X-ray diffraction spectrometry, spectrofluorometry, ultraviolet-visible and Fourier transform infrared spectrometry. Based on the distinct fluorescence quenching of CdTe fluorescence probes in the presence of paracetamol, a simple, rapid and specific method for paracetamol determination was presented. Under optimum conditions, the relative fluorescence intensity of CdTe NPs was linearly proportional to paracetamol concentration from 1.0 × 10⁻⁸ mol/L to 1.6 × 10⁻⁷ mol/L with a detection limit of 4.2 × 10⁻⁹ mol/L. The proposed method was applied to detect paracetamol in commercial tablets with satisfactory results.     

Spectrofluorimetric Assessment of Metoclopramide Hydrochloride Using Terbium Doped in PMMA Matrix Optical Sensor

A new, simple and accurate spectrofluorimetric method for the determination of metoclopramide hydrochloride was developed. The metoclopramide hydrochloride can remarkably enhance the luminescence intensity of the Tb³⁺ ion doped in PMMA matrix at λ_ex = 360 nm in methanol at pH 6.9. The intensity of the emission band at 545 nm of Tb³⁺ ion doped in PMMA matrix is increased due to the energy transfer from metoclopramide hydrochloride to Tb³⁺ in the excited stated. The effect of different parameters, e.g., pH, temperature, Tb³⁺ concentration, foreign ions that control the fluorescence intensity of the produced ion associate was critically investigated. The calibration curve of the emission intensity at 545 nm shows linear response of metoclopramide over a concentration range of 5 × 10⁻⁵–5.0 × 10⁻⁸ M with detection limit of 8.7 × 10⁻¹⁰ M. The method was used successfully for the determination of metoclopramide in pharmaceutical preparations and human serum. The average recovery of 99.48% with standard deviation of 0.32% and 96.98% with standard deviation of 0.4%, of pharmaceutical preparations and human serum respectively, were obtained which compared will with the results obtained from standard LC method of average recovery 99.04% and standard deviation of 0.6% and average recovery of 98.19% with standard deviation of 0.6% of pharmaceutical preparations and human serum, respectively.     

Silica coating of Co–Pt alloy nanoparticles prepared in the presence of poly(vinylpyrrolidone)

This article describes a method for silica coating of Co–Pt alloy nanoparticles prepared in the presence of poly(vinylpyrrolidone) (PVP) as a stabilizer. The Co–Pt nanoparticles were prepared in an aqueous solution at 25–80 °C from CoCl₂ (3.0 × 10⁻⁴ M), H₂PtCl₆ (3.0 × 10⁻⁴ M), PVP (0–10 g/L), and NaBH₄ (4.8 × 10⁻³–2.4 × 10⁻² M). The silica coating was performed for the Co–Pt nanoparticle colloid containing the PVP ([Co] = [Pt] = 3.0 × 10⁻⁵ M) at 25 °C in (1/4) (v/v) water/ethanol solution with tetraethoxyorthosilicate (TEOS) (7.2 × 10⁻⁵–7.2 × 10⁻³ M) and ammonia (0.1–1.0 M). Silica particles, which had an average size of 43 nm and contained multiple cores of Co–Pt nanoparticles with a size of ca. 8 nm, were produced at 1.4 × 10⁻³ M TEOS and 0.5 M ammonia after the preparation of Co–Pt nanoparticles at 80 °C, 5 g/L PVP, and 2.4 × 10⁻² M NaBH₄. Their core particles were fcc Co–Pt alloy crystallites. Their saturation magnetization was 2.0-emu/g sample, and their coercive field was 12 Oe.     

Pyrophosphate Selective Recognition in Aqueous Solution Based on Fluorescence Enhancement of a New Aluminium Complex

A novel and simple fluorescence enhancement method for selective pyrophosphate(PPi) sensing was proposed based on a 1:1 metal complex formation between bis(8-hydroxy quinoline-5-solphonat) chloride aluminum(III) (Al(QS)₂Cl), (L) and PPi in aqueous solution. The linear response range covers a concentration range of 1.6 × 10⁻⁷ to 1.0 × 10⁻⁵ mol/L of PPi and the detection limit of 2.3 × 10⁻⁸ mol/L. The association constant of L-PPi complex was calculated 2.6 × 10⁵ L/mol. L was found to show selectively and sensitively fluorescence enhancement toward PPi over than I₃^-, NO₃^-, CN⁻, CO₃²⁻, Br⁻, Cl⁻, F⁻, H₂PO4⁻ and SO₄²⁻, which was attributed to higher stability of inorganic complex between pyrophosphate and L.     

A Fe<Superscript>3+</Superscript>/Hg<Superscript>2+</Superscript>-Selective Anthracene-Based Fluorescent PET Sensor with Tridentate Ionophore of Amide/β-Amino Alcohol

A new anthracene-based fluorescent PET sensor 1 with a tridentate ionophore of amide/β-amino alcohol displays very good selectivity and sensitivity for Fe³⁺ (K _a = 1.6 × 10³ M⁻¹) and Hg²⁺ (K _a = 2.1 × 10³ M⁻¹) in CH₃CN–H₂O (3:7, v/v) with detection limit of 1 μM. More fluorescence enhancement was observed when 1 selectively detected Fe³⁺ or Hg²⁺ in CH₃CN and its detection limit was up to 0.03 μM.     

Conductivity studies of starch-based polymer electrolytes

A proton-conducting polymer electrolyte based on starch and ammonium nitrate (NH₄NO₃) has been prepared through solution casting method. Ionic conductivity for the system was conducted over a wide range of frequency between 50 Hz and 1 MHz and at temperatures between 303 K and 373 K. Impedance analysis shows that sample with 25 wt.% NH₄NO₃ has a smaller bulk resistance (R _b) compared to that of the pure sample. The amount of NH₄NO₃ was found to influence the proton conduction; the highest obtainable room temperature conductivity was 2.83 × 10⁻⁵ S cm⁻¹, while at 100 °C, the conductivity in found to be 2.09 × 10⁻⁴ S cm⁻¹. The dielectric analysis demonstrates a non-Debye behavior. Transport parameters of the samples were calculated using the Rice and Roth model and thus shows that the increase in conductivity is due to the increase in the number of mobile ions.     

Nonlinear optical absorption and refraction in Ru, Pd, and Au nanoparticle suspensions

We present the results of studies of the nonlinear optical properties of Pd, Ru, and Au nanoparticles. We studied the nonlinear refraction and nonlinear absorption of suspensions of these nanoparticles at 1064-nm wavelength. A relatively strong nonlinear absorption of the Pd nanoparticles was observed in the case of 1064-nm, 50-ps pulses (β=2×10⁻⁹ m W⁻¹). The Ru and Pd nanoparticles showed weak negative nonlinear refraction (γ∼−(6–8)×10⁻¹⁶ m² W⁻¹) in this spectral range. In the case of the Au nanoparticles, a saturated absorption at 532 nm dominated over other nonlinear optical processes.     

Determination of Total Antioxidant Capacity by a New Spectrofluorometric Method Based on Ce(IV) Reduction: Ce(III) Fluorescence Probe for CERAC Assay

A Ce(IV)-based reducing capacity (CERAC) assay was developed to measure the total antioxidant capacity (TAC) of foods, in which Ce(IV) would selectively oxidize antioxidant compounds but not citric acid and reducing sugars which are not classified as antioxidants. The method is based on the electron-transfer (ET) reaction between Ce(IV) ion and antioxidants in optimized acidic sulphate medium (i.e., 0.3 M H₂SO₄ and 0.7 M Na₂SO₄) and subsequent determination of the produced Ce(III) ions by a fluorometric method. The fluorescent product, Ce(III), exhibited strong fluorescence at 360 nm with an excitation wavelength of 256 nm, the fluorescence intensity being correlated to antioxidant power of the original sample. The linear concentration range for most antioxidants was quite wide, e.g., 5.0 × 10⁻⁷–1.0 × 10⁻⁵ M for quercetin. The developed procedure was successfully applied to the TAC assay of antioxidant compounds such as trolox, quercetin, gallic acid, ascorbic acid, catechin, naringin, naringenin, caffeic acid, ferulic acid, glutathione, and cysteine. The proposed method was reproducible, additive in terms of TAC values of constituents of complex mixtures, and the trolox equivalent antioxidant capacities (TEAC coefficients) of the tested antioxidant compounds gave good correlations with those found by reference methods such as ABTS and CUPRAC.     

A Long Wavelength Excitable Fluorophore; Chloro Phenyl Imino Propenyl Aniline (CPIPA) for Selective Sensing of Hg (II)

In this study, a very sensitive and highly selective irreversible optical chemical sensor (optode) for mercury ions was described. The sensing scheme was based on the interaction of Hg (II) with a newly synthesized fluoroionophore; chloro phenyl imino propenyl aniline (CPIPA) in plasticized PVC membrane. The sensor membranes were tested for the determination of mercury ion in aqueous solutions by batch and flow-through methods. The optodes allow determination of Hg (II) in the working range of 1.0 × 10⁻⁹–1.0 × 10⁻⁵ M with a detection limit of 4.3 ppb. The sensor exhibited excellent selectivity for Hg (II) with respect to several common alkali, alkaline earth and transition metal ions. The association constant of the 1:1 complex formation for Hg (II) was found to be K_a = 1.86 × 10⁵ M⁻¹. The CPIPA exhibited high fluorescence quantum yield, long excitation and emission wavelength and high Stokes’ shift values in the solid matrix which makes it compatible with solid state optics.     

Development of Flow Injection Spectrofluorimetric Detection System for the Determination of Homocysteine

In this work, a new simple and sensitive flow injection method is developed for the determination of homocysteine with spectrofluorimetric detection technique. This method is based on the oxidation of homocysteine with Tl (III) in acidic media, producing fluorescence reagent, TlCl₃^2- (λ_ex = 237 nm, λ_em = 419 nm). The effects of chemical parameters (including pH of the solutions, the buffer, Tl (III) and potassium chloride concentrations), instrumental parameters (such as flow rate of the solutions, reaction coil length, and sample loop volume) and temperature on the fluorescence intensity as an analytical signal are studied and optimized. In the optimum conditions of the above variables, homocysteine can be determined in the range 4.0 × 10^-7–40.0 × 10^-6 M with the LDR from 4.0 × 10^-7 to 25.0 × 10^-6 M. The detection limit (with S/N = 3) is 6.0 × 10^-8 M of homocysteine and precision for the injection of 5.0, 10.0 and 15.0 μM of homocysteine are 0.8%, 1.5% and 2.5% (n = 10) respectively. The rate of analysis is 90 samples per hour. The influence of potential interfering substances, including amino acids and carbohydrates is also studied. The proposed method has been successfully used for the determination of homocysteine in the real sample (blood serum and tap water) matrix.