Filter-free ultra-wideband doublet pulses generation based on wavelength conversion and fiber dispersion effect

Filter-free ultra-wideband (UWB) doublet pulse generation is experimentally demonstrated in the optical domain based on cross-gain modulation (XGM) in semiconductor optical amplifier (SOA) and UWB-over-fiber technology is implemented by exploiting dispersion-induced pulse broadening effect in single-mode fiber (SMF). In our proposed system, the SOA generates a polarity-inversed Gaussian pulse train with respect to the injected one through the XGM. After a piece of SMF, the bandwidth of polarity-reversed Gaussian pulse broadens due to the induced dispersion. After the combination of the two light waves with a suitable time delay between them, UWB pulse is obtained. The key parameters for UWB pulse, including central frequency, 10 dB bandwidth, as well as fractional bandwidth are experimentally obtained with 8 GHz, 9.9 GHz and 123% respectively. The generated UWB doublet pulse conforms with the UWB definition of Federal Communications Commission (FCC).     

Ultra-broad and flat supercontinuum generation in short photonic crystal fiber combined with conventional fibers

In order to gain ultra-broad and flat super-continuum (SC) spectrum, we propose and demonstrate a new scheme. By coupling a train of short pulses with 100 fs width and 16.2 mW average power generated by a mode-locked laser into the scheme – short photonic crystal fiber (PCF) combined with conventional fibers. The SC spectrum has 491 nm bandwidth at −15 dBm below the spectral peak with ±0.5 dBm uniformity 100 nm in only 0.45 m PCF. The spectral bandwidth generated in the scheme increases 292 nm than spectrum generated in the two conventional fibers, and increases 152 nm than spectrum generated in the three convention fibers.     

Nanosecond-pulsed erbium-doped fiber lasers with graphene saturable absorber

We demonstrate graphene mode-locked nanosecond erbium-doped fiber laser in an all-fiber ring cavity. The clean and robust pulse train was generated at 27 mW pump power. Resultant central wavelength, repetition rate and pulse width was 1560 nm, 388 kHz and 6 ns, respectively. With two stage fiber amplifier, the output power was 553 mW, corresponding to single pulse energy of 1.4 μJ. In addition, the pulse-width can be varied ranging from 3 ns to 20 ns at repetition rate between 200 kHz and 1.54 MHz by changing the length of the laser cavity.     

Supercontinuum generation using a passive mode-locked stretched-pulse bismuth-based erbium-doped fiber laser

A Supercontinuum (SC) generation in photonic crystal fiber (PCF) is demonstrated using an amplified picosecond stretched-pulses from a passive mode-locked Bismuth-based Erbium-doped fiber laser (Bi-EDFL). The Bi-EDFL employs of a piece of a highly nonlinear 49 cm long Bismuth-based Erbium-doped fiber (Bi-EDF), an optical isolator and a polarization controller in a cavity to generate a mode-locked stretched-pulse via a nonlinear polarization rotation technique. It operates at 1560 nm with a repetition rate of 42 MHz and a pulse width of 131 fs. The SC lights, which extends from 1250 nm to 1910 nm as well as in the visible green wavelength region are obtained with a 100 m long PCF and the amplified pump power of 30 dBm.     

330 MHz,sub 50 fs Yb: Fiber ring laser

We demonstrate 330 MHz repetition rate operation in a ring cavity Yb:fiber laser with an innovative wavelength-division-multiplexing collimator to raise the repetition rate. The spectral bandwidth of the pulse is 30 nm and the dechirped pulse width is 48 fs. The output power is 70 mW with 600 mW, 975 nm pump laser diode.     

A phase stable short pulse generator using a DPMZM and phase modulators for application in 160 GBaud DQPSK systems

A method of 40 GHz phase stable short pulses generation is experimentally demonstrated. It is based on a dual parallel Mach–Zehnder modulator (DPMZM) driven by only one electrical sinusoidal clock and two cascaded phase modulators. The generated pulses are characterized with full-width-at-half-maximum pulse width of 1.9 ps, extinction ratio of 27 dB, timing jitter of 36 fs and signal to noise ratio over 30 dB. The high quality and phase stability of the pulses are further experimentally verified in a 4 × 40 GBaud differential quadrature phase shift keying (DQPSK) optical-time-division-multiplexing (OTDM) system.     

Sub-200 fs microjoule pulses from a monolithic linear fiber CPA system

An all-fiber-integrated linear chirped-pulse amplifier system generating microjoule pulse energies is reported. It is seeded by an all-fiber dissipative-soliton laser and incorporates a newly developed fiber stretcher, whose dispersive properties match that of the grating compressor. Pulse durations of 189 fs with energies of 2.2 μJ were achieved after compression. The average power was 9.8 W at the repetition rate of 4.5 MHz.     

Femtosecond pulse compression in a hollow-core photonic bandgap fiber by tuning its cross section

We present a numerical study of soliton pulse compression in a seven-cell hollow-core photonic bandgap fiber. We analyze the enhancement of both the compression factor and the pulse shape quality of 360 nJ femtosecond pulses at the wavelength of 800 nm by tuning the cross section size of the fiber. We use the generalized non-linear Schrödinger equation in order to modeled the propagation of light pulses along the fiber. Our numerical results show that output compressed pulses can be obtained, in a propagation length of 31 cm, with a compression factor of 5.7 and pulse shape quality of 77% for a reduction of 4.5% of the cross section size of the fiber. The predicted compression factor is 3 times larger than that experimentally obtained in such propagation length of the pulse in a hollow-core photonic bandgap fiber.     

All fiber passively mode locked zirconium-based erbium-doped fiber laser

All passively mode locked erbium-doped fiber laser with a zirconium host is demonstrated. The fiber laser utilizes the Non-Linear Polarization Rotation (NPR) technique with an inexpensive fiber-based Polarization Beam Splitter (PBS) as the mode-locking element. A 2 m crystalline Zirconia–Yttria–Alumino-silicate fiber doped with erbium ions (Zr–Y–Al-EDF) acts as the gain medium and generates an Amplified Spontaneous Emission (ASE) spectrum from 1500 nm to 1650 nm. The generated mode-locked pulses have a spectrum ranging from 1548 nm to more than 1605 nm, as well as a 3-dB bandwidth of 12 nm. The mode-locked pulse train has an average output power level of 17 mW with a calculated peak power of 1.24 kW and energy per pulse of approximately 730 pJ. The spectrum also exhibits a Signal-to-Noise Ratio (SNR) of 50 dB as well as a repetition rate of 23.2 MHz. The system is very stable and shows little power fluctuation, in addition to being repeatable.     

Cascaded continuous-wave singly resonant optical parametric oscillator pumped by a single-frequency fiber laser

We present a cascaded continuous-wave singly resonant optical parametric oscillator (SRO) delivering idler output in mid-IR and terahertz frequency range. The SRO was pumped by an ytterbium-doped fiber laser with 27 W linear polarization pump powers, and based on periodically poled MgO:LiNbO₃ crystal (PPMgLN) in two-mirror linear cavity. The PPMgLN is 50 mm long with 29.5 μm period. The idler power output at 3811 nm was obtained 2.6 W. The additional spectral components that have been attributed to cascaded optical parametric processes are described at increasing pump levels. Besides the initial signal component at about 1476.8 nm, further generated wavelengths with frequency shifts about 47 cm^?1, 94 cm^?1 and 104 cm^?1 were observed. It was speculated that the idler waves lie in the terahertz (THz) domain from the observed results.     

Wavelength tunable,high energy femtosecond laser pulses directly generated from large-mode-area photonic crystal fiber

Wavelength tunable high energy ultrashort laser pulses are generated from a large-mode-area photonic crystal fiber in anomalous dispersion (AD) regime. A simplified laser cavity design with one fine polished facet of the fiber as a cavity mirror is used. The intra-cavity dispersion compensation is achieved by a grating pair, the spatial dispersed light from which also have optical spectrum filtering effects combined with the limited aperture of the fiber core. The laser system is able to generate ultrashort pulses ranging from 494 fs (with 56 nJ pulse energy) to 1.24 ps (with 49 nJ pulse energy) at 55 MHz repetition rate. The filtering mechanism benefits the generation of high energy pulses with narrowing pulse duration in AD regime. An undulation in frequency and time domain is also observed with the increase of the pump power. Furthermore, this laser system is directly used as seed for supercontinuum generation.     

10 GHz ultra-stable short optical pulse generation via phase-modulation enhanced dual-loop optoelectronic oscillator

We report on a high rate, ultra-low timing jitter, short optical pulse generator based on cascaded amplitude and phase modulation in an optoelectronic oscillator. The radio-frequency supermodes are shown to be greatly suppressed with the dual-loop architecture, and a highly coherent and flat optical frequency comb is generated. Optical pulses of 12.8 ps duration are obtained with 27.5 fs integrated timing jitter from 100 Hz to 10 MHz.     

Fundamental and harmonic mode-locking in erbium-doped fiber laser based on graphene saturable absorber

Graphene-based passively mode-locked erbium doped fiber laser is presented. Multilayer graphene was obtained by mechanical exfoliation of pure graphitic block and deposited on the fiber ferrule. The mode-locking performance was investigated under various laser pumping conditions. The laser could operate at fundamental repetition rate of 16.34 MHz with 844 fs pulse duration and 30 mW average output power. Also harmonic-mode locking of the laser is demonstrated. 294 and 800 MHz repetition rates were obtained (corresponding to the 18th and 49th harmonic of the fundamental repetition frequency, respectively) with nearly transform-limited pulses.     

10 Gb/s optical carrier distributed network with W-band (0.1 THz) short-reach wireless communication system

Millimeter-wave (mm-wave) operated in W-band (75 GHz–0.11 THz) is of particular interests, since this frequency band can carry signals at much higher data rates. We demonstrate a 10 Gb/s optical carrier-distributed network with the wireless communication system. The mm-wave signal at carrier frequency of 0.1 THz is generated by a high speed near-ballistic uni-traveling carrier photodiode (NBUTC-PD) based transmitter (Tx), which is optically excited by optical short pulses. The optical pulse source is produced from a self-developed photonic mm-wave waveform generator (PMWG), which allows spectral line-by-line pulse shaping. Hence these optical pulses have high tolerance to fiber chromatic dispersion. The W-band 10 Gb/s wireless data is transmitted and received via a pair of horn antennas. The received 10 Gb/s data is envelope-detected and then used to drive an optical modulator at the remote antenna unit (RAU) to produce the upstream signal sending back to the central office (CO). 20 km single mode fiber (SMF) error free transmission is achieved. Analysis about the optimum repetition rate of the optical pulse source and the transmission performance of the upstream signal are also performed and discussed.     

Novel 60 GHz RoF system with optical single sideband mm-wave signal generation and wavelength reuse for uplink connection

In order to improve RF frequency to achieve higher bandwidth and larger capacity, we propose a novel scheme to generate optical single sideband (SSB) millimeter-wave, in which frequency doubling of local radio frequency (RF) is obtained by using one integrated Mach–Zehnder modulator (MZM), and we theoretically investigate the generating principle of SSB. The optical SSB modulation scheme is employed to generate 60 GHz optical mm-wave and the 2.5 Gb/s baseband signal is simultaneously up-converted at the central station (CS) for downlink transmission, and the optical carrier is reused for uplink connection at the base station (BS). The full-duplex 2.5 Gb/s data are successfully transmitted over 40 km standard single-mode fiber (SMF-28) for both uplink connection and downlink connection with less than 2-dB power penalty. Results show the novel 60 GHz RoF system with optical SSB mm-wave signal generation using optical frequency doubling is feasible and we can obtain simple cost-efficient configuration and good performance over long-distance transmission.     

Numerical analysis of a broadband spectrum generated in a standard fiber by noise-like pulses from a passively mode-locked fiber laser

This paper covers a numerical analysis of supercontinuum spectrum generation in a piece of standard fiber by using as the pump noise-like pulses produced by a passively mode-locked fiber laser. An experimental study was also carried out, yielding results that support the numerical results. In the numerical study we estimated that the spectral extension of the generated supercontinuum reaches ~ 1000 nm, and that it presents a high flatness over a region of ~ 220 nm (1630 nm-1850 nm) when we use as the pump noise-like pulses with a wide optical bandwidth (~ 50 nm) and a peak power of ~ 2 kW. Experimentally, the output signal spectrum extends from ~ 1530 nm to at least 1750 nm and presents a high flatness over a region of 1640 nm to 1750 nm for the same value of numerical input power, 1750 nm being the upper limit of the optical spectrum analyzer. The numerical analysis presented here is thus an essential part to overcome the severe limitation in measuring capabilities and to understand the phenomena of supercontinuum generation, which is mainly related to Raman self-frequency shift. Finally, this work demonstrates the potential of noise-like pulses from a passively mode-locked fiber laser for broadband spectrum generation.     

Generation of long bursts of high-repetition-rate arbitrarily shaped optical pulses using time lens

A technique for the generation of long ultrahigh-speed bursts of optical pulses with arbitrary shapes is proposed. A laser pulse is temporally chirped by a time lens and then passes through a filter with a reconfigurable periodic spectral response, which produces time-delayed replicas of the chirped pulse and recombines them. As a result of the temporal interference between the replicas, the chirped pulse is broken up into short pulses with the shape determined by the chosen filter response. It is demonstrated that the filter acts on a long chirped optical pulse as a temporal modulator with a periodic modulation function. The modulation frequency and bandwidth of the modulator can be much higher than for commercially available high-frequency modulators. The additional advantage of this modulator is the arbitrary shape of the modulation function. A 2.4 ns burst of nearly flat-top pulses with a repetition rate of about 400 GHz is obtained in numerical simulations. In addition, the technique proposed can act as a pulse repetition rate multiplier and a pulse compressor. A repetition rate of 1.589 THz and an individual pulse width of 212 fs are achieved in simulations for a 9.7 ns sinusoidally phase modulated pulse burst.     

Multi-wavelength fiber ring laser based on a sampled chirped fiber Bragg grating with a hybrid gain medium

The novel multi-wavelength fiber ring laser based on a sampled chirped fiber Bragg grating with a single SOA or a hybrid gain medium is demonstrated, respectively. In case of a hybrid gain medium, the SMSR improvement of ~ 5 dB was obtained when compared with the system with a single SOA. The proposed fiber laser offers advantages such as simple structure, low loss, multi-wavelength lasing lines with moderate output power.     

Study of all-fiber asymmetric interleaver based on two-stage cascaded Mach–Zehnder Interferometer

In order to improve the transmission efficiency of optical-fiber communication system with 10 Gb/s + 40 Gb/s, an all-fiber interleaver with unequal passband is proposed and discussed, which is based on a two-stage cascaded Mach-Zehnder interferometer (MZI). The optimum value of structural parameters, such as splitting ratios of the couplers and the physical length differences of the interferometer arms, were chosen. One set of optimized data is validated in the experimental result. The experimental results and the theoretic analysis indicate that an all-fiber optical interleaver with 3 dB passband width in odd channels and even channels could be obtained, which having more than 60 GHz passband and 30 GHz passband, for transmission speed of 40 Gb/s and 10 Gb/s, respectively. By assigning different portions of spectrum to the 10 Gb/s and the 40 Gb/s channels, the bandwidth efficiency requirement of the 40 Gb/s channel is relieved, and therefore longer transmission distance can be achieved.     

Experimental study on tandem pumped fiber amplifier

We present the experimental results of a 1083 nm fiber amplifier tandem pumped by 1030 nm fiber laser. The output characteristics of the tandem pumped amplifier with cladding-pump and core-pump schemes are both investigated. The 1083 nm signal laser has not been efficiently amplified when cladding-pumped by 1030 nm laser for the weak absorption of the gain fiber. The core-pump scheme works well with the amplifier. The output properties with different gain fiber length are experimentally investigated. The maximum output power is 2.4 W with power conversion efficiency of 60%.