Crude fat, diethyl ether extraction, in feed, cereal grain, and forage (Randall/Soxtec/submersion method): collaborative study

A method for determining crude fat in animal feed, cereal grain, and forage (plant tissue) was collaboratively studied. Crude fat was extracted from the animal feed, cereal grain, or forage material with diethyl ether by the Randall method, also called the Soxtec method or the submersion method. The proposed submersion method considerably decreases the extraction time required to complete a batch of samples. The increase in throughput is very desirable in the quest for faster turnaround times and the greater efficiency in the use of labor. In addition, this method provides for reclamation of the solvent as a step of the method. The submersion method for fat extraction was previously studied for meat and meat products and was accepted as AOAC Official Method 991.36. Fourteen blind samples were sent to 12 collaborators in the United States, Sweden, Canada, and Germany. The within-laboratory relative standard deviation (repeatability) ranged from 1.09 to 9.26% for crude fat. Among-laboratory (including within) relative standard deviation (reproducibility) ranged from 1.0 to 21.0%. The method is recommended for Official First Action.     

Crude fat, hexanes extraction, in feed, cereal grain, and forage (Randall/Soxtec/submersion method): collaborative study

A method for determining crude fat in animal feed, cereal grain, and forage (plant tissue) was collaboratively studied. Crude fat was extracted from the animal feed, cereal grain, or forage material with hexanes by the Randall method, also called the Soxtec method or the submersion method. The use of hexanes provides for an alternative to diethyl ether for fat extractions. The proposed submersion method considerably decreases the extraction time required to complete a batch of samples compared to Soxhlet. The increase in throughput is very desirable in the quest for faster turnaround times and the greater efficiency in the use of labor. In addition, this method provides for reclamation of the solvent as a step of the method. The submersion method for fat extraction was previously studied for meat and meat products and was accepted as AOAC Official Method 991.36. Fourteen blind samples were sent to 14 collaborators in the United States, Sweden, Canada, and Germany. The within-laboratory relative standard deviation (repeatability) ranged from 1.23 to 5.80% for crude fat. Among-laboratory (including within) relative standard deviation (reproducibility) ranged from 1.88 to 14.1%. The method is recommended for Official First Action.     

Deleterious effect of ammonium extraction from soil assisted by ultrasound

Ultrasound has been used to assist extraction procedures from solid samples based on the decrease of gradient concentration in the vicinity of particulate matter and the microjet produced during cavitation. In the present work, the harmful effect yield by ultrasound-assisted ammonium extraction from soil samples was observed by comparing with an extraction process assisted by magnetic stirring. Three soil samples from agricultural areas of Bahia state in Brazil were submitted to both extraction processes and ammonium concentrations for conventional stirring procedure were 25% higher than those obtained by the ultrasound-assisted extraction. This same effect was also observed by irradiating ammonium solutions with low frequency ultrasonic waves. After 5 min of ultrasonic irradiation, more than 25% of the ammonium was lost probably as N₂. Possible conversions of N-NH4⁺to hydrazine, hydroxylamine, nitrite and nitrate were evaluated. In addition, an increasing in nitrate concentration by irradiating solution with high saline concentration independent on the initial ammonium concentration was observed.     

Determination of vitamin A (retinol) in infant and medical nutritional formulas with AOAC method 992.06 using a modified extraction procedure: single-laboratory validation

The applicability of AOAC Official Method 992.06, vitamin A (retinol) in milk-based infant formula can be extended to specialty infant formulas, and medical and adult nutritional products with a few minor modifications to the sample preparation procedure. Currently, AOAC Official Method 992.06 is only applicable to milk-based infant formulas containing >500 IU vitamin A per reconstituted quart. When this method is used as written to test specialty infant formulas, vitamin A recoveries are low compared to results generated with alternate validated vitamin A methods. AOAC Method 992.06 vitamin A recoveries can be improved significantly in specialty infant formulas if the amount of potassium hydroxide used during the saponification step is doubled. With this one minor modification to the sample preparation procedure, AOAC Method 992.06 demonstrates acceptable precision and accuracy for the quantitation of vitamin A (retinol) in specialty infant formulas, milk- and soy-based infant formulas, and adult and medical nutritionals. Because increasing the amount of potassium hydroxide can cause emulsions to form, 2-4 mL aliquots of reagent alcohol may need to be added to some samples to separate the organic and aqueous layers during the extraction step. A single-laboratory validation of these modifications was completed. During validation, 15 different product matrixes were analyzed. The intermediate precision averaged 2.70% RSD, and spike recovery data averaged 96.3%.     

Ion chromatographic determination of phosphorus soluble in different extracting media in fertilizers

A new method based on ion chromatography (IC) was developed for the determination of phosphorus in fertilizers. Fertilizers were extracted with water, mineral acids, and 2% formic acid, 2% citric acid, and neutral ammonium citrate solutions according to European Regulation No. 2003/2003 of the European Parliament and the Council of October 13, 2003, or the Decree of the Italian Agriculture Minister of June 17, 2002; the extracts were analyzed by direct injection, after simple filtration, by IC on an IonPac AS19 (250 x 4 mm id) column, using a KOH (21-50-21 mM) gradient and suppressed conductivity detection. The calibration plot was linear over the range of 5-50 mg/L (r(2) of >0.999). The method was evaluated by comparison with a gravimetric method according to established norms. Associated uncertainty at the 95% confidence level was established as 0.47% for the determination of 3-46% P2O5 by IC. A good chromatographic separation of phosphorus forms such as phosphates and phosphites, and some other important anions like nitrates, chlorides, and sulfates present in many commercial fertilizers was also possible, with a linear response over the range of 5-50 mg/L. After a more complete validation, this IC determination of phosphorus could replace more tedious methods such as those using gravimetric determinations.     

Comparison of methods for extraction of ethyl carbamate from alcoholic beverages in gas chromatography/mass spectrometry analysis

A procedure to analyze ethyl carbamate (EC) by gas chromatography/mass spectrometry was optimized and validated. Deuterated EC (d5-EC) was added to the samples as an internal standard followed by extraction with polystyrene crosslinked polystyrene cartridges using minimal volumes of ethyl acetate. The EC response was measured in selective ion monitoring (SIM) mode and found to be linear in the range between the limit of quantitation (10 micro/L) and 1000 microg/L. EC recoveries varied from 92 to 112%, with the average value of 100 +/- 8%. The procedure compared well (r2 = 0.9970) with the existing AOAC Official Method with the added benefits of minimal solvent usage and reduced matrix interferences.     

Removal of aqueous ammonium with magnesium phosphates obtained from the ammonium-elimination of magnesium ammonium phosphate

In order to recycle magnesium ammonium phosphate (MgNH4PO4.6H2O: MAP) obtained from MAP process, which is one of the attractive processes for removal of aqueous ammonium and phosphate from wastewater, ammonium elimination from MAP to magnesium phosphates and ammonium incorporation into the magnesium phosphates have been investigated in the present study. It is confirmed that magnesium hydrogen phosphate (MgHPO4) is favorably obtained from the ammonium elimination from MAP at temperatures greater than 353 K, although magnesium phosphate (Mg3(PO4)2) and magnesium pyrophosphate (Mg2P2O7) have been suggested as possible candidates. Based on the dissolution-precipitation mechanism for the removal of aqueous ammonium with magnesium phosphates, three magnesium phosphates were employed for the removal of aqueous ammonium. The order of the removal rate of the aqueous ammonium was MgHPO4>Mg3(PO4)2>Mg2P2O7, as expected from the solubility of those magnesium phosphates. The removability of the solid obtained from ammonium elimination of MAP is also confirmed. The present results show that MAP can be employed as an advanced material for the removal/recovery of ammonium, although it is generally accepted that an excess of MAP obtained from the wastewater treatment can be only used as a slow-acting fertilizer.     

Determination of phosphorus in fertilizers by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) method was developed for the determination of phosphorus in fertilizers. Total phosphorus, direct extraction available phosphorus (EDTA), and water-soluble phosphorus, reported as phosphorus pentoxide (P205), in 15 Magruder check fertilizers were measured by ICP-AES, and the results were compared with those obtained by the AOAC official method. Five analytical wavelengths of phosphorus, 177.499, 178.287, 213.618, 214.914, and 253.565 nm, were tested for the determination of phosphorus in fertilizers, and their detection limits were obtained. Acid effects of perchloric acid and possible matrix effects of aluminum, calcium, magnesium, potassium, and sodium were negligible for phosphorus determination. Wavelength 213.618 nm was the best analytical wavelength for phosphorus determination by all 3 sample preparation methods for the selected Magruder fertilizers. The results demonstrated that the accuracy and precision of the ICP-AES method were comparable with those of the official methods.     

Determination of water (moisture) and dry matter in animal feed, grain, and forage (plant tissue) by Karl Fischer titration: collaborative study

A Karl Fischer method for determining water (dry matter) in animal feed and forages was collaboratively studied. Water was extracted from animal feed or forage material into methanol-formamide (1 + 1) directly in the Karl Fischer titration vessel by high-speed homogenization. The water was titrated at 50 degrees C with one-component Karl Fischer reagent based on imidazole. Ten blind samples were sent to 9 collaborators in the United States, Canada, and Germany. The within-laboratory relative standard deviation (repeatability) ranged from 1.14 to 6.99% for water or from 0.09 to 0.56% for dry matter. Among-laboratory (including within-) relative standard deviation (reproducibility) ranged from 5.35 to 10.73%, or from 0.44 to 0.77% for dry matter. The authors recommend that the method be adopted as Official First Action by AOAC INTERNATIONAL. A comparable alternative extraction procedure using boiling methanol is also recommended for Official First Action.     

Evaluation of a cloud point extraction method for the preconcentration and quantification of silver nanoparticles in water samples by ETAAS

ABSTRACT

A simple and reliable analytical method using instrumentation available in most of the laboratories has been developed for the separation and determination of silver nanoparticles in water samples. Cloud point extraction (CPE) was used for the separation of silver nanoparticles (AgNPs) from the sample and these nanoparticles were then determined by electrothermal atomic absorption spectrometry (ETAAS). Parameters related to the cloud point extraction procedure (Triton X-114 concentration, type of complexing agent (EDTA or Na₂S₂O₃), pH, incubation temperature, incubation and centrifugation time) were selected using a multivariate approach (designs of experiments); 8.6% (v/v) Triton X-114, 750 µL saturated EDTA and pH 7 were selected as the optimum conditions. Calibration standards in a concentration range from 0 to 10 µg L^?1 of AgNPs were subjected to the CPE procedure to obtain quantitative recoveries. The LOD and LOQ were 0.04 and 0.13 µg L^?1, respectively. The method is selective for the extraction of AgNPs, and ionic Ag remains in the aqueous phase. Single particle inductively coupled plasma mass spectrometry (SP-ICP-MS) was used to evaluate the effect of the CPE procedure in particle size, and no changes were observed. Finally, the procedure was applied to wastewater samples spiked with nanoparticles with quantitative recoveries.     

聚乙二醇-硫酸铵双水相萃取次甲基蓝的研究

利用分光光度法研究了次甲基蓝在聚乙二醇-硫酸铵双水相体系的萃取行为,探索了质量配比(mPEc/m(NH4)2SO4)、温度和次甲基蓝的浓度对双水相及次甲基蓝萃取率(Y)的影响.实验表明:(1)在一定的温度和浓度下,随着mPEC/m(NH4)2SO4的减小,分配系数K( cup/clow)增加,萃取率Y略有减小;(2)在一定的质量配比和浓度下,分配系数K(cup/clow)随温度的升高而增大,但萃取率Y却基本保持不变;(3)在一定的质量配比和温度下,随着次甲基蓝浓度的增加,分配系数K(cup/clow)增大;萃取率Y略有增加.在mPEG/m( NH4) 2SO4为1.50∶1,c次甲基蓝=8.915×10-5mol/L、t=30℃的实验条件下,K(cup/clow)=22.14,萃取率(y)可达95.43％.     

Molar absorptivities of aflatoxins B1, B2, G1, and G2 in acetonitrile, methanol, and toluene-acetonitrile (9 + 1) (modification of AOAC Official Method 971.22): collaborative study

Four laboratories participated in a mini-collaborative study of AOAC Official Method 971.22, Standards for Aflatoxins, Thin-Layer Chromatographic Method, to extend the method to 3 replacement solvents for benzene for calibration of standard aflatoxin solutions. Triplicate test sample vials, each containing 25 micrograms of the respective aflatoxin for each of the 4 aflatoxins and for each of the solvents, were prepared and sent to each collaborator. The collaborators dissolved the aflatoxin in each vial in 2 mL solvent, measured the UV spectrum, and reported the absorptivity maxima near 350 nm. The concentrations of the aflatoxins in the test samples were determined by dissolving identical test samples in benzene-acetonitrile (98 + 2) and following the procedure described in AOAC Official Method 971.22. These concentrations were, in turn, used to determine the molar absorptivities in the other 3 solvents (see Table 1). AOAC Official Method 971.22 has been modified to extend its applicability to 3 replacement solvents for benzene for calibration of standard aflatoxin solutions.     

Rapid immunoaffinity-based method for determination of zearalenone in corn by fluorometry and liquid chromatography

An immunoaffinity-based method was developed to determine zearalenone in corn. Corn samples were extracted in acetonitrile-water (90 + 10, v/v), applied to an immunoaffinity column, and eluted with methanol. The isolated toxin was quantitated either by reaction with aluminum chloride hexahydrate (AlCl3.6H2O) prior to measurement with a fluorometer or injection into a liquid chromatographic (LC) system with a fluorescence detector. Performance was evaluated in terms of antibody specificity, limit of detection, percentage recovery, precision, column capacity, assay linearity, and comparison with AOAC Official Method 985.18. With the immunoaffinity column cleanup procedure, only zearalenone and its metabolites were recognized by the antibody (> or = 75% recovery). Limits of detection were 0.10 microgram/g for the fluorometer and 0.10 or 0.0025 microgram/g (sensitive method) for the LC method. Percentage recovery averaged 105% (fluorometer) and 93% (LC method), with average relative standard deviations (RSDs) of 15.7 and 9.3%. Naturally contaminated samples gave comparable RSDs of 8.3 and 9.9% for the fluorometer and LC methods, respectively. Column capacity was 4.0 micrograms with 89% recovery. Assay linearity was comparable for both methods (r2 = 0.998). Optimum assay ranges were 0.10-5.0 micrograms/g for the fluorometer and 0.10-50 or 0.0025-5.0 micrograms/g (sensitive method) for the LC method. Comparative analysis of 17 naturally contaminated corn samples using Zearala Test LC and the official AOAC LC method for detection of zearalenone showed that Zearala Test is statistically comparable to the AOAC Official Method 985.18 (r2 = 0.747).     

Development of a simultaneous extraction and cleanup method for pyrethroid pesticides from indoor house dust samples

An efficient and reliable analytical method was developed for the sensitive and selective quantification of pyrethroid pesticides (PYRs) in house dust samples. The method is based on selective pressurized liquid extraction (SPLE) of the dust-bound PYRs into dichloromethane (DCM) with analysis by gas chromatography/mass spectrometry. Various adsorbents and combinations of extraction solvents and temperatures were evaluated to achieve a high-throughput sample preparation that eliminates the post-extraction cleanup step. The final method used sulfuric acid-impregnated silica (acid silica) and neutral silica together in the extraction cell with the dust sample to provide both extraction and cleanup simultaneously. The optimal ratio of dust/acid silica/silica was 1:0.8:8. The extraction was performed at 2000 psi, at 100 °C with DCM for 5 min in three cycles. Method precision and accuracy were evaluated by the analysis of triplicate aliquots of the dust samples and the samples fortified with the target PYRs. The accuracy measured as the recoveries of the PYRs in the fortified samples ranged from 85% to 120%. The precision measured as the relative standard deviation of replicate samples was within ±25%. The SPLE method was applied to 20 house dust samples collected from households that participated in two field studies regarding exposures to pesticides and other pollutants. Similar concentrations of target PYRs were obtained for the SPLE and a stepwise extraction/cleanup procedure. The SPLE procedure reduces organic solvent consumption and increases the sample throughput when compared with a traditional stepwise extraction and cleanup procedure. This study demonstrates that the SPLE procedure can be applied to complex dust matrices for analysis of PYRs for large scale exposure or environmental monitoring studies.     

A new method of evaluation of element pollutant mobility in sediments

The application of a strong chelating agent for the screening test of element mobility in sedimentary systems was investigated. Single-step and sequential extraction procedures were applied to four sediment samples collected from an industrially polluted region of Eastern Slovakia. A sequential extraction procedure (SEP), recommended by the Institute for Reference Materials and Measurements (IRMM), was applied and used as a reference extraction method. A single-step extraction with 0.05 mol dm⁻³ ethylenediaminetetraacetic acid (EDTA) was adapted for sediments when extraction conditions were optimised. The extraction efficiency of the single-step procedure was compared with that of SEP. The contents of elements extracted by Na2EDTA were in good agreement with the sum of the first three steps of the SEP for Fe, Mn, and Co. Na₂EDTA can therefore be considered capable to extract the majority of elements associated with the reducible sedimentary phase — bound to Fe and Mn oxides in the regional geological conditions of the monitored region. Thus, Na₂EDTA extraction of Fe and Mn can serve as an economical, time-saving supplementary test for the IRMM procedure. This paper is dedicated to the memory of Erika Krakovská Presented at the XVIIIth Slovak Spectroscopic Conference, Spišská Nová Ves, 15–18 October 2006.     

Effect of some environmental ligands and fertilizers on humic acid complexation with strontium

The effect of some environmental ligands and certain fertilizers on the complexation of strontium with humic acid wasinvestigated colorimetrically and radiometrically. The results indicate that Na₂-EDTA, Na₃-citrate and NaCl compete to complex strontium in solution with the sequence: chloride < citrate < EDTA while Na₃-phosphate has the reverse behavior. In the case of nitrogen containing fertilizers, the results show that urea, Mg-ammonium nitrate and ammonium nitrate increase the availability of strontium to plants and microorganisms.     

Liquid chromatographic determination of urea in water-soluble urea-formaldehyde fertilizer products and in aqueous urea solutions: collaborative study

Water soluble urea-formaldehyde (UF) fertilizers, manufactured by complex reaction of urea and formaldehyde, typically contain varying amounts of unreacted urea. A liquid chromatography method for the analysis of urea in these products, and in aqueous urea solutions, was collaboratively studied. An amine chromatography column was used to separate the unreacted urea from numerous UF reaction products present in these liquid fertilizers. Unreacted urea was determined by using external urea standards with UV detection at 195 nm. The standards and test samples were prepared in the mobile phase of 85% (v/v) acetonitrile in water. Ten laboratories analyzed 5 different UF-based commercial products containing unreacted urea in the range of 6 to 17% by weight, and 5 different concentrations of urea in water equivalent to commercial products of that nature. The aqueous urea solutions contained 2-20% urea (w/w). The range of s(R) values for the 5 UF-based commercial fertilizers was 0.49-1.02 and the %RSD(R) was 1.94-6.14. The s(R) range for the 5 urea solutions was 0.10 to 0.79 and the %RSD(R) range was 2.54 to 4.88. The average recovery of urea from the aqueous urea solutions was 96-103%. Therefore, this method is capable of monitoring urea nitrogen manufacturers' label claims and total nitrogen claims in those cases where urea is the sole source of plant food nitrogen. Based on the collaborative study data, the authors recommend this method be approved for AOAC Official First Action status.     

Confirmation of gentamicin and neomycin in milk by weak cation-exchange extraction and electrospray ionization/ion trap tandem mass spectrometry

A new procedure for the confirmation of two aminoglycoside antibiotics in milk was developed and validated. This work is among the early applications of ion trap mass spectrometry for regulatory methodology, and it incorporates a novel weak cation-exchange extraction. The procedure was validated for the confirmation of both gentamicin and neomycin at 30 ng ml(-1) and above. Milk is first treated with acid and centrifuged. The supernate, excluding the fat layer, is buffered with sodium citrate to neutral pH. The extract is applied to a weak cation-exchange solid-phase extraction column. Aminoglycosides are eluted with acidified methanol. Following separation by ion-pair liquid chromatography, analytes are ionized with an electrospray interface. Protonated molecular ions are selectively stored in an ion trap mass spectrometer, then collisionally dissociated to yield unique product ion spectra. Confirmation is based on matching spectral responses between samples and comparison standards consisting of a bona fide standard spiked into control extracts. Method performance was demonstrated with replicate samples of control milk, fortified milk, and milk containing incurred residues of each compound.     

A rapid method for the determination of benzylpenicillin in serum by reversed-phase HPLC

A simple procedure for the determination of benzylpenicillin in serum is described. The assay involves the extraction of the drug and the internal standard (phenoxymethylpenicillinic acid) from the sample into dichloromethane, using tetrabutylammonium hydrogen sulfate neutralized with NaOH and buffered with citrate as an ion-pairing reagent. RP-HPLC was performed on a Spherisorb 5 ODS column, eluting the drugs isocratically with 14% acetonitrile in 10 mM ammonium acetate buffer. Monitoring was by UV detection at 208 nm. Our results show that the method is accurate and reproducible, permitting quantification of serum levels of benzylpenicillin without interference from other drugs commonly used in therapy. Analytical recovery was greater than 79.2%.     

Should acid ammonium oxalate replace hydroxylammonium chloride in step 2 of the revised BCR sequential extraction protocol for soil and sediment?

The revised, four-step BCR sequential extraction for soil or sediment has been compared with an alternative procedure in which 0.2 mol l⁻¹ ammonium oxalate (pH 3) replaced 0.5 mol l⁻¹ hydroxylammonium chloride (pH 1.5) in step 2, the reducible step. A variety of substrates were studied: BCR CRM601, a sewage sludge amended soil, two industrial soils, and a steel manufacturing by-product (basic oxygen furnace filter cake). Greater amounts of iron were recovered in step 2 when acid ammonium oxalate was used, for all substrates. Similar trends were observed for copper. Manganese and zinc were not strongly affected by the procedural modification, except for zinc in the two industrial soils, where oxalate extraction proved more efficient than use of hydroxylammonium chloride. A large proportion of the calcium and lead isolated in step 2 of the BCR procedure was not released until step 3 when the alternative procedure with oxalate in step 2 was used. This is probably due to rapid precipitation of analyte oxalates from solution. Thus, whilst oxalate offers superior dissolution of iron-containing matrix components, it should not be used if calcium or lead concentrations are to be measured. Selection of the most appropriated sequential extraction protocol for use in a particular study must always be carried out on the basis of “fitness for purpose” criteria. However, the revised BCR protocol, involving use of 0.5 mol l⁻¹ NH₂OH·HCl in the reducible step, appears to be more generally applicable than procedures involving acid ammonium oxalate.