Fast determination of tetrafluoroborate by high-performance liquid chromatography using a monolithic column

Fast determination of tetrafluoroborate by high-performance liquid chromatography using a silica-based monolithic column and direct conductivity detection was carried out. Chromatographic separation was performed on a Chromolith Speed ROD RP-18e column (50 mm x 4.6 mm i.d.) with tetrabutylammonium hydroxide (TBA-OH)+ phthalic acid as eluent. The effects of eluent concentration, eluent pH, column temperature and flow rate on retention time of tetrafluoroborate were investigated. The optimized chromatographic conditions for determination of tetrafluoroborate were using 0.5mM TBA-OH + 0.31 mM phthalic acid (pH 5.5) as eluent, column temperature of 30 degrees C and flow rate of 6.0 mL/min. Retention time of tetrafluoroborate was less than 1min under the conditions. Common anions (Cl(-), Br(-), NO3(-) and SO4(2-)) did not interfere with the determination of tetrafluoroborate. Detection limit (S/N = 2) for tetrafluoroborate was 1.4 mg/L. The linear range of calibration curve between peak area and the concentration of tetrafluoroborate was from 1.4 to 100.0 mg/L. The reproducibility was 0.09% and 1.8% (n = 5) relative standard deviation (RSD) for retention time and peak area, respectively. The method has been applied to the determination of tetrafluoroborate in ionic liquids. Recoveries of tetrafluoroborate after spiking were 98.2-101.5%.     

Liquid chromatography determination of natural dyes in extracts from historical Scottish textiles excavated from peat bogs

Textiles excavated from Scottish sites belonging now to the collections of the National Museums of Scotland, including seventeenth century textiles from peat bogs in the Scottish Highlands and Islands, were selected for analysis by high performance liquid chromatography with photodiode array detection (PDA HPLC) to detect whether any dyes remained and, if so, to identify their biological sources. Dye components were identified in 36 of the 81 samples analysed. Although it was not possible to identify the exact sources of the dyestuffs because of the wide-spread occurrence of these natural dyes components, the study has shown that textiles previously not thought to have been coloured had detectable traces of dye. Before the historical textiles were analyzed, an improved extraction procedure that combined the routine acid hydrolysis method with one using dimethylformamide (DMF) was applied. The DMF method enabled increased recovery of major flavonoid and anthraquinoid compounds, and very high efficiency of recovery of indigotin even in textiles with no colour visible, thereby complementing the acid hydrolysis method already in use. Extracts from historical thread samples were analysed by PDA HPLC using a reversed-phase gradient system comprising of a C18 column (150 mm x 4.6 mm i.d., 25 +/- 1 degrees C) with water, methanol and o-phosphoric acid at an eluent flow rate of 1.2 ml/min. A preliminary investigation to improve the detection limits further for a selection of natural dyes was made by comparing results from the 4.6mm internal diameter (i.d.) column with a narrow bore C18 column (2.1 mm i.d.). An increase in the detector response was observed for narrow-bore column proving its possibility of enhancement of sensitivity.     

Chloride analysis in magnesium metal using ion chromatography with conductometric detection

A simple, rapid and accurate method for the determination of chloride in magnesium metal has been developed. The quantitative determination of chloride was accomplished by anion exchange chromatography with conductometric determination. A Metrosep Anion Dual 2 analytical column connected in series with a Metrosep RP guard column was used for chloride separation. A solution containing a mixture of 1.3 mM Na2CO3 and 2 mM NaHCO3 was used as eluent. The method requires a sample dissolution using nitric acid. The limit of detection for the determination of chloride is 50 mg kg(-1) and the relative standard deviation was 5% for the overall method. The recovery of chloride added was 99-102%. No interference was observed from either the closely eluting "system peak" or the nitrate peak in the determination of chloride.     

Efficient separation of acetate and formate by ion chromatography: application to air samples in a cultural heritage environment

A method for the separation of acetate and formate anions by ion chromatography has been optimized under various measurement conditions (e.g. the composition of the mobile phase, and the flow rate of the eluent). For this purpose, two different analytical columns were examined: the IonPac AS14 (250 mm x 4 mm i.d.; designed mostly for the separation of inorganic anions) and the Allsep A-2 (150 mm x 4.6 mm i.d.; designed for the separation of low-molecular mass organic acids). However, nearly baseline separation of acetate and formate has been found on each column using the following conditions: (i) IonPac AS14 column and 2.0 mM Na2B4O7 solution as an eluent with a flow rate of 1.0 ml/min, or (ii) Allsep A-2 column and an eluent containing a mixture of 1.2 mM Na2CO3 plus 1.5 mM NaHCO3 with a flow rate of 1.3 ml/min. Additionally, the separation of fluoride from acetate and formate on both columns was studied. On the IonPac AS14 column it was possible to separate all three investigated anions. However, on the Allsep A-2 column, when the concentration of fluoride was comparable to, or higher than acetate, it was impossible to achieve good separation of these two anions, even using the optimized elution procedure. Therefore, the measurements of real samples were carried out with the use of IonPac AS14 column. The concentrations of acetate and formate have been determined in the air samples of the Cathedral of Cologne (Germany), after sampling the corresponding acids by passive diffusion tubes. Average concentrations of 122 and 9 microg/m(3) for acetic and formic acids were found, respectively, inside the Cathedral and in a depot with medieval stained glass panels.     

Simultaneous determination of inorganic cations by capillary ion chromatography with a non-suppressed contactless conductivity detector

A non-suppressed capillary ion chromatographic method with a laboratory-made packed cation-exchange column (100 mm × 0.32 mm i.d.) was developed for the separation and simultaneous determination of five common inorganic cations (sodium, ammonium, potassium, magnesium and calcium). Cation exchangers were prepared by the reaction of the hydroxyl group on the surface of diol-group bonded silica gel with 1,3-propanesultone in methanol. Simultaneous separation of these five common inorganic cations were achieved within 17 min using 1 mM methanesulfonic acid and 0.1 mM 15-crown-5 ether in methanol-water (8:2, v/v) as the eluent. The effects of organic solvents and crown ethers in the eluent on the retention of analytes were investigated. The limits of detection (S/N = 3) of the cations were in the range of 18-124 μg/l, the linear correlation coefficients were 0.9991-0.9998, and the RSD values of retention time and peak height were all smaller than 2.1%. The present analytical method was successfully applied to the rapid and direct determination of inorganic cations in samples of river water and commercial drinks, with satisfactory results.     

Retention behavior of alkali, alkaline earth and transition metal cations in ion chromatography with an unmodified silica gel column

An unmodified silica gel (Develosil 30-5) column (150×4.6 mm I.D.) has been applied to the ion chromatographic separation of alkali, alkaline earth and transition metal cations. The retention behavior of the above cations on the bare substrate was investigated using a number of weak inorganic and organic acid eluents. During this investigation, several separations were achieved and the most suitable eluent conditions were identified. It was concluded that: (a) 1.5 mM HNO₃-0.5mM pyridine-2,6-dicar☐ylic acid eluent was the most effective for the simultaneous separation of common alkali and alkaline earth metal cations, (b) 1.5 mM oxalic acid eluent resulted in the best separation of alkali, alkaline earth, and transition metal cations, (c) 0.5 mM CuSO₄ eluent could be used for the separation of alkali metal cations alone and (d) 0.5 mM ethylenediamine-oxalic acid eluent at pH 5.5 resulted in themost efficient separation of both alkaline earth and transition metal cations.     

Determination of trichloroacetate in human serum and urine by ion chromatography

A simple and rapid ion chromatographic method has been developed for the determination of trichloroacetate in human serum and urine. Two short (50 x 5 mm i.d.) low-capacity anion-exchange resin columns in series were used as the analytical column and a mixture of 35 mM sodium hydroxide, 20 mM p-hydroxybenzonitrile and 2% V/V acetonitrile (pH 12.3) as the eluent. The calibration graph was rectilinear from 0.3 to 33 mg l-1 of trichloroacetate at 10 microS with a detection limit (3 sigma) of 0.08 mg l-1. The recovery of trichloroacetate, obtained by analysing spiked serum and urine samples, was in the range 98.2-101% and the coefficient of variation was always less than 3.0%.     

A novel ion chromatographic method based on cation-exchange and acid-base interactions for the simultaneous determination of total alkalinity and monovalent cations in samples of microliter volume

An ion chromatographic (IC) method based on the use of titrant (strong acid) as the stationary phase was developed for simultaneous determination of total alkalinity (TA) and monovalent cations. The titrant used in this study was obtained by initially loading lithium dodecylsulfate (Li-DS) onto a reversed-phase material and then conditioning the column with a slightly acidified aqueous LiCl solution (a mixture of 50.0 mM LiCl and 0.1 mM H2SO4). When a small amount of a basic sample was injected onto a column prepared in this way, the basic species (Bn-) reacted predominantly with H+ on the stationary phase and the reaction with the eluent phase was negligible due to the very low concentration of eluent H+ (in the eluent, a molar ratio of [Li+]/[H+] = 250:1 applied). The stationary phase H+ consumed in the acid-base reaction was then re-supplied by H+ from the eluent. By monitoring the conductance of the eluent using conductivity, an induced peak resulting from the basic species was observed. Calibration graphs of peak areas vs. molar concentration of the basic species for OH-, HCO3- and H2PO4- were found to be identical. CO3(2-), HPO4(2-), and B4O7(2-) also gave identical calibration curves but their slope values were twice those for HCO3-. The detection limit for HCO3- was less than 3.2 microM and the calibration curve was linear up to 12.3 mM (injection volume, 100 microL). Seawater was directly analyzed and its total alkalinity was found to be 2.87 mM (RSD 0.53%, n = 5), which was in good agreement with the result of 2.88 mM (RSD 3.2%, n = 5) obtained using auto-potentiometric titration. Na+ and K+ were determined simultaneously and the concentrations were 481.6 and 10.6 mM, respectively.     

Determination of sulfonated azo dyes in river water samples by capillary zone electrophoresis

A method based on capillary zone electrophoresis coupled with photodiode-array detection has been developed to determine several sulfonated dyes, including a sulfonated dye (acid yellow 1), and the sulfonated azo dyes acid orange 7, acid orange 12, acid orange 52, acid red 26, acid red 27 and acid red 88. A CElect-FS75 CE column is used. The electrophoresis buffer contains a 1:5 dilution of 10 mM phosphoric acid and tetrabutylammonium hydroxide buffer (pH 11.5), and 25 mM of triethylamine, the final pH being 11.55. The detection limits for the seven dyes ranged from 0.1 to 4.53 microg/ml. Spiked river water samples (100 ml), containing different concentration levels (0.025-0.150 microg/ml) of the dyes were analyzed after acidification (pH 3) and pre-concentration in disposable SPE Oasis HLB, 1 ml cartridges.     

Determination of tocopherols,tocopherolquinones and tocopherolhydroquinones by gas chromatography-mass spectrometry and preseparation with lipophilic gel chromatography

A method has been developed for the simultaneous determination of a range of aromatic amines using cation-exchange chromatography performed on a standard ion chromatography column using d.c. amperometric detection. The analytes separated were 2,4- and 2,6-toluenediamine (2,4- and 2,6-TDA), aniline, o-toluidine, benzidine, p-chloroaniline, 4,4'-diaminodiphenyl (4,4'-DDP), m-nitroaniline and 1-naphthylamine. A Dionex CS12 column was used with gradient elution from an initial eluent of 5% CH3CN+35 mM H2SO4 to 27% CH3CN+35 mM H2SO4 (at 35 min). Detection limits in the range 2.6-22.6 microg/l were observed for all analytes except m-nitroaniline, for which the detection limit was 201 microg/l. Linear calibrations and good precision were observed and the method was applied to the determination of benzidine, p-chloroaniline and 1-naphthylamine in wastewater samples. Further, the separation was also used (after some modification of the eluent conditions) for the determination of 2,4- and 2,6-toluene diisocyanate (2,4- and 2,6-TDI) and 4,4'-methylenediphenyl diisocyanate (4,4'-MDI) after their hydrolysis to 2,4-TDA, 2,6-TDA and 4,4'-DDP. Detection limits for 2,6- and 2,4-TDI and 4,4'-MDI were 3.8, 8.2, and 11.2 microg/l, respectively. The method was applied to the determination of diisocyanates in air.     

Determination and pharmacokinetic analysis of salvianolic acid B in rat blood and bile by microdialysis and liquid chromatography

Salvianolic acid B is an herbal ingredient isolated from Salvia miltiorrhiza. An in vivo microdialysis sampling method coupled to high-performance liquid chromatography has been developed for continuous monitoring of protein-unbound salvianolic acid B in rat blood and bile. Microdialysis probes were inserted into the jugular vein/right atrium and bile duct of Sprague-Dawley rats, and a dose of 100 mg/kg salvianolic acid B was then administered via the femoral vein. Dialysates were collected and directly injected into a liquid chromatographic system. Salvianolic acid B was eluted using a microbore reversed-phase ODS 5 microm (150 mm x 1 mm I.D.) column. Isocratic elution of salvianolic acid B was achieved within 10 min using the liquid chromatographic system. The chromatographic mobile phase consisted of acetonitrile-methanol-20 mM monosodium phosphoric acid (pH 3.5) (10:30:60, v/v/v) containing 0.1 mM 1-octanesulfonic acid with 0.05 ml/min. The wavelength of the UV detector was set at 290 nm. Salvianolic acid B in both blood and bile dialysates was adequately determined using the liquid chromatographic conditions described, although the blank bile pattern was more complex. The retention times of salvianolic acid B in rat blood and bile dialysates were found to be 7.2 min. Peak-areas of salvianolic acid B were linear (r2 > 0.995) over a concentration range of 0.1-50 microg/ml. In vivo recoveries of microdialysis probes of salvianolic acid B in rat blood and bile averaged 22 +/- 2% and 41 +/- 1%, respectively. This study indicates that salvianolic acid B undergoes hepatobiliary excretion.     

反相硅胶整体柱离子对色谱法快速测定吡啶离子液体阳离子

建立了整体柱离子对色谱-紫外检测法梯度淋洗快速分离测定4种吡啶离子液体阳离子的方法。分离采用C18反相硅胶整体柱,以离子对试剂(用柠檬酸调节pH值)-乙腈为淋洗液,并采用多级梯度洗脱程序。实验考察了色谱柱、离子对试剂、乙腈浓度、色谱柱温度及流速对吡啶阳离子保留的影响,并讨论了其保留规律。咪唑阳离子的保留符合碳数规律。最佳色谱条件是:在流速3.0 mL/min,柱温30℃下,以1.0 mmol/L庚烷磺酸钠(pH 4.0)(A)+乙腈(B)为淋洗液进行梯度洗脱。淋洗梯度为0～2.0 min,10%B;2.0～2.5 min,10%～15%B;2.5～4.0 min,15%B;4.0～4.5 min,15%～20%B;4.5～10.0 min,20%B。在此条件下,4种吡啶阳离子可在7 min内基线分离。所测阳离子的检出限(S/N=3)为0.05～0.17 mg/L;峰面积的相对标准偏差(n=5)小于0.6%。将本方法用于实验室合成的离子液体样品和污水样品的分析,加标回收率在95.7%～99.0%之间。本方法准确、快速,具有较好的实用性。     

Ion chromatography on a latex-coated silica monolith column

A silica monolith column (Merck Chromolith, 100 mm x 4.6 mm) has been coated with Dionex AS9-SC latex nanoparticles to convert the column into an anion-exchange stationary phase. For comparison purposes, a reversed-phase silica monolith was also converted into an anion-exchange column by coating with the cationic surfactant didodecyldimethylammonium bromide (DDAB). Separations of common inorganic anions were carried out using 7.5 or 5.0 mM 4-hydroxybenzoic acid at pH 7.0 along with suppressed conductivity detection. Direct comparisons were then made between the two columns in terms of selectivity, efficiency and stability. The latex-coated column was on average 50% more efficient than the DDAB-coated column. A 10% decrease in retention times was observed on the DDAB column over 11 h of continuous eluent flow, while the latex coating exhibited <1% change in retention even after 2.5 months of periodic use.     

Analysis of cyanobacterial toxins by hydrophilic interaction liquid chromatography-mass spectrometry

The combination of hydrophilic interaction liquid chromatography with electrospray mass spectrometry (HILIC-MS) has been investigated as a tool for the analysis of assorted toxins produced by cyanobacteria. Toxins examined included saxitoxin and its various analogues (1-18), anatoxin-a (ATX-a, 19), cylindrospermopsin (CYN, 20), deoxycylindrospermopsin (doCYN, 21), and microcystins-LR (22) and -RR (23). The saxitoxins could be unequivocally detected in one isocratic analysis using a TSK gel Amide-80 column eluted with 65% B, where eluent A is water and B is a 95% acetonitrile/water solution, both containing 2.0 mM ammonium formate and 3.6 mM formic acid. The analysis of ATX-a, CYN and doCYN required 75% B isocratic. Simultaneous determination of 1-21 was also possible by using gradient elution. HILIC proved to be suitable for the analysis of microcystins, but peak shape was not symmetric and it was concluded that these compounds are best analysed using existing reversed-phase methods. The HILIC-MS method was applied to the analysis of field and cultured samples of Anabaena circinalis and Cylindrospermopsis raciborskii. In general, the method proved quite robust with similar results obtained in two different laboratories using different instrumentation.     

Ion-exclusion chromatographic behavior of aliphatic carboxylic acids and benzenecarboxylic acids on a sulfonated styrene--divinylbenzene co-polymer resin column with sulfuric acid containing various alcohols as eluent

The addition of C1-C7 alcohols (methanol, ethanol, propanol, butanol, heptanol, hexanol and heptanol) to dilute sulfuric acid as eluent in ion-exclusion chromatography using a highly sulfonated styrene-divinylbenzene co-polymer resin (TSKgel SCX) in the H+ form as the stationary phase was carried out for the simultaneous separations of both (a) C1-C7 aliphatic carboxylic acids (formic, acetic, propionic, isobutyric, butyric, isovaleric, valeric, 2-methylvaleric, isocaproic, caproic, 2,2-dimethyl-n-valeric, 2-methylhexanoic, 5-methylhexanoic and heptanoic acids) and (b) benzenecarboxylic acids (pyromellitic, hemimellitic, trimellitic, o-phthalic, m-phthalic, p-phthalic, benzoic and salicylic acids and phenol). Heptanol was the most effective modifier in ion-exclusion chromatography for the improvement of peak shapes and a reduction in retention volumes for higher aliphatic carboxylic acids and benzenecarboxylic acids. Excellent simultaneous separation and relatively highly sensitive conductimetric detection for these C1-C7 aliphatic carboxylic acids were achieved on the TSKgel SCX column (150 x 6 mm I.D.) in 30 min using 0.5 mM sulfuric acid containing 0.025% heptanol as eluent. Excellent simultaneous separation and highly sensitive UV detection at 200 nm for these benzenecarboxylic acids were also achieved on the TSKgel SCX column in 30 min using 5 mM sulfuric acid containing 0.075% heptanol as eluent.     

Determination of monovalent inorganic anions in high-ionic-strength samples by electrostatic ion chromatography with suppressed conductometric detection

A new ion chromatographic (IC) system has been established by using micelles of 3-(N,N-dimethylmyristylammonio)propanesulfonate (Zwittergent 3-14) loaded onto a reversed-phase packed column as the separation column with an electronic rotary switching valve packed-bed suppressor for conductometric detection of inorganic anions. An aqueous H3BO3-Na2B4O7 solution has been demonstrated to be the most desirable eluent for this IC system. The relationship between retention time and the concentration of the borate eluent was determined for a series of model anionic analytes and this relationship was found to be opposite to that exhibited in a conventional anion-exchange IC system. The rapid elution and complete separation of monovalent inorganic anions were obtained by initially using a high-concentration borate solution as the eluent for a short-period, and then switching to a lower-concentration borate eluent to complete the separation. Detection limits for nitrite, bromide, nitrate, and chlorate were 0.85, 0.88, 0.95 and 4.8 microM, respectively, when a 7.0 mM Na2B4O7 eluent was used. Moreover, the ability to directly detect these monovalent anions in samples containing high concentrations of sulfate and/or chloride ions provided a major advantage of this approach.     

Measurement of penbutolol and 4-hydroxypenbutolol in plasma or serum by HPLC

A simple HPLC method for penbutolol and 4-hydroxypenbutolol assay has been developed. Plasma or serum (200 microliters) is vortex-mixed (30 s) with Tris solution (2 M, pH 10.6) containing an internal standard (50 microliters) and methyl t-butyl ether (200 microliters). After centrifugation, the extract (100 microliters) is analysed using an unmodified silica column (250 x 5 mm ID) and iso-octane-methanol-methyl t-butyl ether (55:25:20) containing ammonium perchlorate (10 mM, pH 5.7) as eluent and with fluorescence detection. No interference has been encountered and the limit of accurate measurement for both compounds is 5 micrograms/l.     

Simultaneous determination of zidovudine and lamivudine from rat plasma, amniotic fluid and tissues by HPLC

A sensitive HPLC method has been developed and validated for the simultaneous quantification of zidovudine (AZT) and lamivudine (3TC) in rat plasma, amniotic fluid and placental and fetal tissues. Samples were processed by solid-phase extraction using C2 cartridges. Chromatography was performed using a phenyl column (5 microm, 150 x 2 mm i.d.) under a flow rate of 0.2 mL/min. The mobile phase consisted of 8% acetonitrile in 5 mM 1-heptane sulfonic acid dissolved in 30 mM ammonium formate buffer (pH 3.3). The method was validated in the range 0.25-50 microg/mL for both 3TC and AZT in the four biological matrices. Finally, the method was applied to a study involving fetal transport of co-administration of these compounds in a pregnant rat.     

Chemiluminescence high-performance liquid chromatography for the determination of hyaluronic acid, chondroitin sulphate and dermatan sulphate.

A sensitive chemiluminescence high-performance liquid chromatographic method has been developed for the determination of hyaluronic acid, chondroitin sulphate and dermatan sulphate as their unsaturated disaccharide-dansylhydrazine derivatives involving an effective sample clean-up system. The dansylhydrazones of the unsaturated disaccharides derived from the hyaluronic acid, chondroitin sulphate and dermatan sulphate by chondroitinase ABC and/or chondroitinase ACII, were separated by reversed-phase chromatography using a mixture of 0.1 M sodium acetate buffer (pH 6.0) and 80% acetonitrile on a column (250 mm x 4.0 mm I.D.) packed with amide-80 silica beads (5 microns diameter). For post-column elution in the chemiluminescence system, 1 mM bis[2-(3,6,9-trioxadecanyloxycarbonyl)-4-nitrophenyl]oxalate and 3mM hydrogen peroxide in acetonitrile were used. The detection limit of each glycosaminoglycan was 100 fmol. The method was applicable to the determination of the levels of hyaluronic acid, chondroitin sulphate and dermatan sulphate in rat peritoneal mast cells.     

Determination of some aliphatic carboxylic acids in anaerobic digestion process waters by ion-exclusion chromatography with conductimetric detection on a weakly acidic cation-exchange resin column

The determination of seven aliphatic carboxylic acids, formic, acetic, propionic, isobutyric, n-butyric, isovaleric and n-valeric acids in anaerobic digestion process waters was examined using ion-exclusion chromatography with conductimetric detection. The analysis of these biologically important carboxylic acids is necessary as a measure for evaluating and controlling the process. The ion-exclusion chromatography system employed consisted of polymethacrylate-based weakly acidic cation-exchange resin columns (TSKgel OApak-A or TSKgel Super IC-A/C). weakly acidic eluent (benzoic acid), and conductimetric detection. Particle size and cation-exchange capacity were 5 microm and 0.1 meq./ml for TSKgel OApak-A and 3 microm and 0.2 meq./ml for TSKgel Super IC-A/C, respectively. A dilute eluent (1.0-2.0 mM) of benzoic acid was effective for the high resolution and highly conductimetric detection of the carboxylic acids. The good separation of isobutyric and n-butyric acids was performed using the TSKgel Super IC-A/C column (150 mm x 6.0 mm i.d. x 2). The simple and good chromatograms were obtained by the optimized ion-exclusion chromatography conditions for real samples from mesophilic anaerobic digestors, thus the aliphatic carboxylic acids were successfully determined without any interferences.