Electrical properties of amorphous and crystalline InSb and InAs thin films

Amorphous films of indium antimonide (0.02–0.26 μm) and indium arsenide (0.03–0.3 μm) were formed on goldseal glass, freshly cleaved mica and NaCl substrates by using a “flash evaporation” technique. The post-deposition heat treatment was carried out on these films when the amorphous → crystalline transformation was observed. The transformation was characterized by a sudden and large fall in the resistance of the film at a particular temperature depending on the thickness. This transformation was confirmed by transmission electron micrographs and diffraction patterns obtained on the films before and after heat treatment. The transformation temperatures lie between 495–525 K for indium antimonide and 550–575 K for indium aresenide, for the thickness range involved in our investigations. The electrical conductivity measurements showed a temperature dependent activation in the high temperature region and hopping conduction in the low temperature region (Mott's theory). The activation energies, at different temperatures for various thicknesses were calculated and presented. While no Hall mobility could be observed in as-deposited films, very low mobilities were observed in annealed thick films (t > 2000 Å). Thermoelectric power for InSb films was found to vary from 0.075–0.17 mV/K for films of thickness ranging from 1000–2300 Å, whereas for InAs films, its value varied from 0.09–0.27 mV/K for the thickness range, 1250–2500 Å. These measurements indicated the conductivity to be n-type and supported the hopping conduction mechanism observed in low temperature conductivity measurements.     

Structural and Electrical Properties of Cd Doped InSe Thin Films

Polycrystalline Cd doped InSe thin films were obtained by thermal co‐evaporation of alpha‐In₂Se₃ lumps and Cd onto glass substrates at a temperature of 150°C. The films were annealed at 150°C and 200°C. The films were found to contain around 46% In, 47% Se and 7% Cd in weight. The films exhibited p‐type conductivity. The results of conductivity measurements have revealed that thermionic emission and variable range hopping are the two dominant conduction mechanisms, in the temperature ranges of 320‐160 K and 150‐40 K respectively. It was observed that above 240 K mobility is limited by the scattering at the grain boundaries. As the temperature decreases, thermal lattice scattering followed by the ionized impurity scattering dominate as the two main mechanisms controlling the mobility. Acceptor to donor concentration ratio was found to be slightly increasing due to annealing.     

Influence of thermal annealing on the composition and structural parameters of DC magnetron sputtered titanium dioxide thin films

Titanium dioxide films have been deposited using DC magnetron sputtering technique. Films were deposited onto RCA cleaned p‐silicon substrates at the ambient temperature at an oxygen partial pressure of 7 × 10^–5 mbar and sputtering pressure of 1 × 10 ^–3 mbar. The deposited films were annealed in the temperature range 673–873 K. The structure and composition of the films were confirmed using X‐ray diffraction and Auger electron spectroscopy. The structure of the films deposited at the ambient was found to be amorphous and the films annealed at 673 K and above were crystalline with anatase structure. The lattice constants, grain size, microstrain and the dislocation density of the film are calculated and correlated with annealing temperature.     

Influence of precursor concentration on structural,morphological and electrical properties of spray deposited ZnO thin films

Nanostructured ZnO thin films were coated on glass substrate by spray pyrolysis using Zinc acetate dihydrate as precursor. Effect of precursor concentration on structural, morphological, optical and electrical properties of the films was investigated. The crystal structure and orientation of the ZnO thin films prepared with four different precursor solution concentrations were studied and it was observed that, the prepared films are polycrystalline in nature with hexagonal wurzite structure. The peaks are indexed to (100), (002), (101), (102) and (110) planes. Grain size and texture coefficient (TC) were calculated and the grain size found to increase with an increase in precursor concentration. Presence of Zn and O elements was confirmed with EDAX spectra. Optical absorption measurements were carried out in the wavelength region of 380 to 800 nm and the band gap decreases as precursor concentration increases. The current‐voltage characteristics were observed at room temperature and in dark. It was found that for the films deposited at four different precursor concentrations, the conductivity improves as precursor concentration increases. As trimethyl amine TMA is a good marker for food quality discrimination, sensing behavior of the films at an optimized operating temperature of 373 K, towards various concentrations of (TMA) was observed and reported. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Fractional composition of large crystallite grains: A unique microstructural parameter to explain conduction behavior in single phase undoped microcrystalline silicon

We have studied the dark conductivity of a broad microstructural range of plasma deposited single phase undoped microcrystalline silicon (μc-Si:H) films in a wide temperature range (15–450 K) to identify the possible transport mechanisms and the interrelationship between film microstructure and electrical transport behavior. Different conduction behaviors seen in films with different microstructures are explained in the context of underlying transport mechanisms and microstructural features, for above and below room temperature measurements. Our microstructural studies have shown that different ranges of the percentage volume fraction of the constituent large crystallite grains (F_cl) of the μc-Si:H films correspond to characteristically different and specific microstructures, irrespective of deposition conditions and thicknesses. Our electrical transport studies demonstrate that each type of μc-Si:H material having a different range of F_cl shows different electrical transport behaviors.     

Effects of annealing on structural,electrical and optical properties of AgGa(Se0.5S0.5)2 thin films deposited by using sintered stoichometric powder

The structural, electrical and optical properties of AgGa(Se_0.5S_0.5 )₂ thin films deposited by using the thermal evaporation method have been investigated as a function of annealing in the temperature range of 450–600 °C. X‐ray diffraction (XRD) analysis showed that the structural transformation from amorphous to polycrystalline structure started at 450 ^oC with mixed binary phases of Ga₂Se₃, Ga₂S₃, ternary phase of AgGaS₂ and single phase of S. The compositional analysis with the energy dispersive X‐ray analysis (EDXA) revealed that the as‐grown film has different elemental composition with the percentage values of Ag, Ga, Se and S being 5.58, 27.76, 13.84 and 52.82 % than the evaporation source powder, and the detailed information about the stoichometry and the segregation mechanisms of the constituent elements in the structure have been obtained. The optical band gap values as a function of annealing temperature were calculated as 2.68, 2.85, 2.82, 2.83, and 2.81 eV for as‐grown, annealed at 450, 500, 550, and 600 °C samples, respectively. It was determined that these changes in the band gap are related with the structural changes with annealing. The temperature dependent conductivity measurements were carried out in the temperature range of 250‐430 K for all samples. The room temperature resistivity value of as‐grown film was found to be 0.7x10⁸ (Ω‐cm) and reduced to 0.9x10⁷ (Ω‐cm) following to the annealing. From the variation of electrical conductivity as a function of the ambient temperature, the activation energies at specific temperature intervals for each sample were evaluated. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Polycrystalline Lead Tin Chalcogenide Thin Film Grown by Spray Pyrolysis

PbSnS₂ thin film has been prepared for the first time by spray pyrolysis technique on FTO substrate at 570K. The preliminary optical and structural characteristics of the film have been reported. The optical studies showed that the value of the fundamental absorption edge lies at 1.47eV and a low energy absorption band tail has been observed. The prepared film is p‐ type electrical conductivity, polycrystalline in nature and has an orthorhombic crystal structure. The value of an average grain size of the film is 350Å.     

Electrical and Photoelectrical Properties of Vacuum Deposited SnSe Thin Films

Polycrystalline thin films of tin selenide have been prepared by vacuum deposition at a substrate temperature of 150°C and reported. X‐ray diffraction, optical transmission, electrical conductivity and photoconductivity studies have been carried out on these films. Annealing the films at 300°C for 2 hours improves the crystallinity and a preferred orientation along the (111) plane develops. The optical transmission measurement reveals that the SnSe thin films have a direct allowed band gap of 1.26 eV. Electrical conductivity study shows that the conductivity increases with increasing temperature. The observed electrical conductivity at low temperature is explained based on hopping conduction mechanism. The photoconductivity measurement indicates the presence of continuously distributed deep localised gap states in this material.     

Influence of substrate temperature on microcrystalline structure and optical properties of ZnTe thin films

ZnTe thin films were deposited onto well‐cleaned glass substrates kept at different temperatures (Ts = 303, 373 and 423 K), by vacuum evaporation method under the pressure of 10^–5 Torr. The thickness of the film was measured by quartz crystal monitor and verified by the multiple beam interferometer method. The structural characterization was made using X‐ray diffractometer with filtered CuKα radiation. The grain sizes of the microcrystallines in films increases with increase in substrate temperature. The strain (ε), grain size (D) and dislocation density (δ) was calculated and results are discussed based on substrate temperature. Optical behaviour of the film was analyzed from transmittance spectra in the visible region (400–800 nm). The optical transition in ZnTe films is direct and allowed type. The optical band gap energy shows an inverse dependence on substrate temperature and thickness. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Growth and electrical properties of flash evaporated AgGaTe2 thin films

Thin films have been prepared by flash evaporation technique of a stoichiometric bulk of AgGaTe₂ compound in vacuum and analysed using X‐ray diffraction, transmission electron microscopy, selected area diffraction and energy dispersive analysis of X‐rays. The effect of substrate temperature on the structural properties – grain size, film orientation, composition, and stoichiometry of the films have been studied. It was found that the polycrystalline, stoichiometric films of AgGaTe₂ can be grown in the substrate temperature range of 473K < Ts < 573K. The influence of substrate temperature (Ts) on the electrical characteristics‐ Resistivity, Hall Mobility, Carrier concentration of AgGaTe₂ thin films were studied. The electrical resistivity was found to decrease with increase in substrate temperature up to 573K and then increases. The variation of activation energy of AgGaTe₂ thin films were also investigated. The implications are discussed. (© 2006 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electrical conductivity and dielectric properties of potassium sulfamate single crystals

Single crystals of potassium sulfamate are grown by the method of slow evaporation at constant temperature. AC electrical conductivity of potassium sulfamate is measured in the temperature range 300–430 K and in the frequency region between 100 Hz and 3 MHz along the a, b and c‐axes. Complex impedance spectroscopy is used to investigate the frequency response of the electrical properties of the potassium sulfamate single crystal. Temperature variation of AC conductivity and dielectric measurements show a slope change around 345 K for both heating and cooling run and this anomaly is attributed as phase transition, which is well supported by the DSC measurements. Value of loss tangent in the temperature region 330–400 K is found to be very low. Activation energies for the conduction process are calculated along the a, b and c‐axes. (© 2011 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Electrical conductivity of sulfamic acid single crystals

Single crystals of sulfamic acid have been grown by the method of slow evaporation at constant temperature. DC electrical conductivity was measured in the temperature range 300 ‐ 440 K along a, b and c‐axes. Conductivity measurements show slope change near 330 K and 410 K. The slope change observed around 330 K may be attributed as due to a phase transition which has been well supported by the DSC and DTA measurements. Slope change observed around 410 K is attributed as the onset of the thermal decomcoposition as evidenced by TGA curve. TGA studies show the crystal is very stable up to 440 K. Activation energies for the conduction process are calculated for all measured crystallographic directions. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Thickness and substrate orientation dependence of ferromagnetism in Mn doped ZnO thin films

The effect of film thickness and substrate orientation on ferromagnetism in Mn doped ZnO thin films have been studied. The Mn doped ZnO films of different thickness (15, 35 and 105 nm) have been grown on both Si (100) and Si (111) substrates. The structural, electrical, optical, elemental and magnetic properties of the films have been investigated by X‐ray diffraction (XRD), Hall Effect measurements, photoluminescence (PL), energy dispersive spectroscopy (EDS) and vibrating sample magnetometer (VSM), respectively. It is found that all the properties are strongly influenced by the film thickness and substrate orientation. The XRD analysis confirmed that the formation of high quality monophasic hexagonal wurtzite structure for all the grown films. The room temperature VSM measurements showed that the films of lower thickness have better ferromagnetism than that of the thicker films grown on both the substrates. Among the lower thickness films, the film grown on Si (111) substrate has higher saturation magnetization (291×10^‐5 emu cm^‐3) due to high density of the defects. The observed ferromagnetism has been well justified by XRD, Hall measurements and PL. The presence of Mn atoms in the film has been confirmed by EDS. (© 2012 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Properties of InAs co‐doped ZnO thin films prepared by pulsed laser deposition

InAs co‐doped ZnO films were grown on sapphire substrates by pulsed laser deposition. The grown films have been characterized using X‐ray diffraction (XRD), Hall effect measurements, Atomic force microscope (AFM) and Field emission scanning electron microscope (FESEM) in order to investigate the structural, electrical, morphological and elemental properties of the films respectively. XRD analysis showed that all the films were highly orientated along the c‐axis. It was observed from Hall effect measurements that InAs co‐doped ZnO films were of n‐type conductivity. In addition, the presence of In and As has been confirmed by Energy dispersive X‐ray analysis. AFM images revealed that the surface roughness of the films was decreased upon the co‐doping. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Microstructural and optoelectrical properties of transparent conducting ZnO:Al thin films for organic solar cells

The Al‐doped zinc oxide (ZnO:Al) thin films were grown on glass substrates by the magnetron sputtering technique. The films were characterized with X‐ray diffractometer, four‐point probe and optical transmission spectroscopy, respectively. The dependence of microstructural, electrical and optical properties on deposition temperature was investigated. The results show that all the films have hexagonal wurtzite structure with highly c‐axis orientation. And the microstrural and optoelectrical properties of the films are observed to be subjected to the deposition temperature. The ZnO:Al film prepared at the deposition temperature of 650 K possesses the best optoelectrical properties, with the lowest electrical resistivity (6.1×10⁻⁴ Ω·cm), the highest average visible transmittance (85.3%) and the maximum figure of merit (0.41 Ω⁻¹). The optical energy gap of the films was estimated from Tauc's law and observed to be an increasing tendency with the increment of the deposition temperature. Furthermore, the refractive index of the films was determined by the optical characterization methods and the dispersion behavior was studied by the single electronic oscillator model.     

DC conductivity studies in K3Na(SeO4)2 single crystals

DC electrical conductivity studies were carried out along the three crystallographic axes for Tripotassium sodium diselenate (K₃Na(SeO₄)₂ or KNSe). Earlier studies of phase transition in this crystal show successive phase transitions at 334 K, 346 K, 730 K, and 758 K. In this paper we report the dc electrical conductivity measurements in the temperature region 303 K – 430 K along a, b and c – axes. An anomaly in conductivity was obtained around 341 K and another one around 333 K. These can be attributed as due to phase transitions in this crystal. A strong anomaly also has been observed along the c‐axis and comparatively week one along a and b axes around 395 K for the first time. This can be due to newly observed phase transition in the crystal. DSC taken for the sample also shows endothermic peak supporting the occurrence of newly observed phase transition. (© 2009 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Characteristics of ITO films fabricated on glass substrates by high intensity pulsed ion beam method

Transparent conductive oxides such as indium tin oxide (ITO) are interesting materials due to their wide-band gaps, high visible light transmittance, high infrared reflectance, high electrical conductivity, hardness and chemical inertness. ITO films were fabricated on soda lime glass substrates by using high-intensity pulsed ion beam (HIPIB) technique. The as-deposited films comprised of partially crystallized In₂O₃ and after annealing at 500 °C for 1 h the film changed to polycrystalline phase. After annealing carrier concentration and Hall mobility increased while specific resistance and sheet resistance decreased quickly; and this trend was also observed when film thickness increased up to 300 nm for the post-annealed samples. Further increase in thickness of the film changed the electrical properties slightly. Atomic force microscopy (AFM) revealed that roughness decreased after 500 °C annealing for 1 h in air, except for the film of 65 nm thick. The thickness of the film which relates to the carrier concentration and mobility, degree of crystallization, size of the grain, and connections among grains in film are main factors to determine film’s electrical properties.     

Crystallization behavior of e-beam evaporated Ga5Ge15Te80 thin films

Ga₅Ge₁₅Te₈₀ thin films have been deposited by e-beam evaporation method. The chemical composition of the deposited films was identified using energy dispersive X-ray spectrometry. The electrical conductivity, σ of the deposited films during heating/cooling cycles was investigated in the temperatures 298–570 K. The conductivity curve showed two sudden upward trends during the first heating cycle. The first upward trend occurs in the temperature range 408–430 K and was attributed to the amorphous-to-crystalline phase transformation. While the second is in the temperature range 470–495 K, and can be attributed to the crystallization process. However, for second heating cycle the conductivity curve becomes reversible. The optical band gap of the as-deposited and annealed film at annealing temperature 423 K was determined from the recorded transmittance and reflectance spectra. The obtained results were confirmed throughout the X-ray and transmission electron microscope studies.     

Influence of photonic excitations on the electrical parameters of TlInS2 crystals

The photo‐excitation effect on the current transport mechanism in TlInS₂ crystals has been studied by means of dark and illuminated conductivity measurements. The temperature‐dependent electrical conductivity analysis in the temperature region of 110‐340 K revealed the domination of the thermionic emission and the thermally assisted variable range hopping (VRH) of charge carriers above and below 160 K, respectively. Above 160 K, the conductivity activation energies in the dark are found to be 0.28 and 0.15 eV in the temperature regions of 340‐240 K and 230‐160 K, respectively. In the temperature region of 110‐150 K, the dark variable range hopping analysis revealed a density of localized states of 1.99×10²² cm^–3eV^–1, an average hopping distance of 0.53 nm and an average hopping energy of 79.65 meV. When the sample was photo‐excited, the values of the conductivity activation energies, the density of localized states near the Fermi level and the average hopping energy were observed to decrease sharply with increasing illumination intensity. On the other hand, the average hopping distance increased with rising illumination intensity. Such behaviours were attributed to the Fermi level shift and/or trap density reduction by electron‐hole recombination. (© 2010 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

纳米金刚石薄膜的掺杂、表/界面调控及性能研究

本文综述了近年来国内外研究者在纳米金刚石薄膜的掺杂、导电性能、场发射性能和电化学性能等方面的工作,涉及化学气相沉积法制备n型纳米金刚石薄膜,离子注入掺杂纳米金刚石晶粒提高薄膜的n型导电性能,金属离子注入制备场发射性能良好的纳米金刚石薄膜,低剂量离子注入和晶粒表面氧终止态获得高迁移率n型电导,纳米金刚石/石墨烯复合结构的调控对其电学及电化学性能的影响,以及硼掺杂金刚石薄膜电极的微结构和电化学性能研究等。综合分析发现,晶粒掺杂和表界面协同调控可以提升薄膜的电学性能、场发射性能及电化学性能,为纳米金刚石薄膜在纳米电子器件、电化学电极等领域的应用提供了理论基础。