Rapid and sensitive HPLC method for the simultaneous determination of paraquat and diquat in human serum.

A rapid and sensitive HPLC method for the simultaneous determination of paraquat and diquat in human serum has been developed. After deproteinization of the serum with 10% trichloroacetic acid, the samples were separated on a reversed-phase column, and subsequently reduced to their radicals with alkaline sodium hydrosulfite solution. These radicals were monitored with a UV detector at 391 nm. This method permitted the reliable quantification of paraquat over linear ranges of 50 ng - 10 microg/ml and 100 ng - 10 microg/ml for diquat in human serum. The within- and between-day variations are lower than 2.3 and 2.2%, respectively. This technique was also utilized to determine the paraquat and diquat serum levels in a patient who had ingested herbicide (Prigrox L) containing paraquat and diquat.     

Solid-phase extraction and sample stacking-capillary electrophoresis for the determination of quaternary ammonium herbicides in drinking water

Conditions for the simultaneous determination of paraquat, diquat and difenzoquat by capillary zone electrophoresis were established by combining two preconcentration procedures. Off-line solid-phase extraction was used for the isolation and preconcentration of quats in drinking water. Quats were then analysed by capillary electrophoresis using sample stacking with matrix removal as on-column preconcentration procedure. Two different porous graphitic carbon cartridges were compared. The breakthrough volumes of the three herbicides were calculated and the loading capacity of the sorbents was compared. Recoveries higher than 80% for difenzoquat and around 40% for paraquat and diquat were obtained when a sample volume of 250 ml was percolated. For the stacking-capillary electrophoresis analysis of quats, 50 mM acetic acid-ammonium acetate (pH 4.0), 0.8 mM cetyltrimethylammonium bromide with 5% (v/v) methanol as carrier electrolyte was used. Detection limits, based on a signal-to-noise ratio of 3:1, were lower than 0.3 microg l(-1) for standards in Milli-Q water, and lower than 2.2 microg l(-1) for drinking water samples. Run-to-run and day-to-day precision of the method were established. The two preconcentration procedures used together was successfully applied to the analysis of the three herbicides in spiked drinking water at concentrations below the maximum admissible US Environmental Protection Agency levels.     

Sample stacking with matrix removal for the determination of paraquat, diquat and difenzoquat in water by capillary electrophoresis

Conditions for the simultaneous determination of paraquat, diquat and difenzoquat by capillary zone electrophoresis using a stacking technique in a chemically modified capillary have been established. To apply the stacking method with sample matrix removal for the analysis of cations, an anodic electroosmotic flow is mandatory. For quats, 50 mM acetic acid-ammonium acetate (pH 4.0) with 5% (v/v) methanol as electrophoretic buffer and the addition of 0.8 mM cetyltrimethylammonium bromide as wall capillary organic modifier was proposed. Field polarity reversal time was optimised for several sample matrices. Detection was carried out at 220 and 255 nm. Detection limits, based on a signal-to-noise ratio of 3:1, were lower than 15 microg l(-1) for standards in Milli-Q water and two to ten times higher for drinking water samples. Run-to-run and day-to-day reproducibility have been established. The method was successfully applied to the determination of the three herbicides in spiked drinking water.     

Automated on-line in-tube solid-phase microextraction followed by liquid chromatography/electrospray ionization-mass spectrometry for the determination of chlorinated phenoxy acid herbicides in environmental waters

A method for the determination of six chlorinated phenoxy acid herbicides in river water was developed using in-tube solid-phase microextraction (SPME) followed by liquid chromatography/electrospray ionization-mass spectrometry (LC/ESI-MS). In-tube SPME is an extraction technique for organic compounds in aqueous samples, in which analytes are extracted from a sample directly into an open tubular capillary by repeated draw/eject cycles of the sample solution. Simple mass spectra with strong signals corresponding to [M-H]- and [M-RCOOH]- were observed for all herbicides tested in this study. The best separation of these compounds was obtained with a C18 column using linear gradient elution with a mobile phase of acetonitrile-water containing 5 mmol l-1 dibutylamine acetate (DBA). To optimize the extraction of herbicides, several in-tube SPME parameters were examined. The optimum extraction conditions were 25 draw/eject cycles of 30 microliters of sample in 0.2% formic acid (pH 2) at a flow rate of 200 microliters min-1 using a DB-WAX capillary. The herbicides extracted by the capillary were easily desorbed by 10 microliters acetonitrile. Using in-tube SPME-LC/ESI-MS with time-scheduled selected ion monitoring, the calibration curves of herbicides were linear in the range 0.05-50 ng ml-1 with correlation coefficients above 0.999. This method was successfully applied to the analysis of river water samples without interference peaks. The limit of quantification was in the range 0.02-0.06 ng ml-1 and the limit of detection (S/N = 3) was in the range 0.005-0.03 ng ml-1. The repeatability and reproducibility were in the range 2.5-4.1% and 6.2-9.1%, respectively.     

Analysis of the herbicides paraquat,diquat and difenzoquat in drinking water by micellar electrokinetic chromatography using sweeping and cation selective exhaustive injection

Optimum conditions for the determination of the herbicides paraquat, diquat and difenzoquat by micellar electrokinetic chromatography (MEKC) using sweeping and cation-selective exhaustive injection (CSEI) as on-line concentration methods were developed. Sodium dodecyl sulfate (80 mM) in 50 mM phosphate buffer (pH 2.5) with 20% acetonitrile was used as a background electrolyte for the methods studied. The limits of detection, based on a signal-to-noise ratio of 3:1, were about 2.6-5.1 mg 1(-1) in purified water when MEKC was applied for the standards. By using an on-line preconcentration method known as sweeping-MEKC, up to a 500-fold increase in detection sensitivity was obtained whereas up to a 50 000-fold increase for CSEI-sweeping-MEKC was achieved. The limits of detection using optimum CSEI-sweeping-MEKC were lower than 1 microg 1(-1) and the method was validated obtaining good reproducibility (relative standard deviation lower than 22%) and linearity. CSEI-sweeping-MEKC was successfully applied to the determination of the three herbicides in spiked tap water below the levels established by the US Environmental Protection Agency.     

Simultaneous determination of paraquat and diquat in serum using capillary electrophoresis.

The use of capillary electrophoresis for simultaneous separation and detection of the two bipyridylium herbicides, paraquat and diquat, was investigated. Both herbicides were extracted from fortified sera with disposable ODS-silica cartridges. Separation was carried out using a capillary tube (50 microns i.d., 750 mm) of fused silica containing 10 mM glycine-HCl buffer (pH 3.0), 40 mM NaCl and 20% methanol as the carrier. Paraquat and diquat were completely separated in 10 min at an applied potential of 20 kV. On-column UV monitoring allowed detection of both herbicides simultaneously. The assay sensitivity was 0.05 micrograms/mL (signal-to-noise ratio, 2:1), which probably increases with increase in the sample volume of serum. Analytical recovery of both herbicides added to serum was about 97% at concentrations of 0.5-2.0 micrograms/mL.     

Simultaneous determination of binary mixtures of sulfonylurea herbicides in water by first-derivative photochemically induced spectrofluorimetry.

First-derivative photochemically induced spectrofluorimetry (PIF-1D) is applied to the simultaneous determination of binary mixtures of 4 sulfonylurea herbicides in aqueous micellar samples. Synthetic binary mixtures of sulfometuronmethyl with chlorsulfuron, metsulfuron-methyl, and 3-rimsulfuron, respectively, are well resolved by using the zero-crossing point procedure. PIF-1D allows the determination of binary mixtures of these herbicides with linear dynamic ranges over about 2 orders of magnitude, limits of detection between 0.5 and 52 ng/mL, and relative standard deviations within 0.3-2.9%. Application to the determination of binary mixtures of these herbicides in spiked tap water samples yielded satisfactory recoveries (90-117%).     

Capillary electrophoresis-mass spectrometry for the analysis of quaternary ammonium herbicides

Conditions for the simultaneous determination of the three herbicides paraquat, diquat and difenzoquat and the two plant growth regulators chlormequat and mepiquat by pressure-assisted capillary electrophoresis coupled to mass spectrometry (ion-trap) using electrospray as ionisation source have been established. A 200 mM formic acid-ammonium formate buffer solution at pH 3.0 with 50% of methanol was used as carrier electrolyte. Some capillary electrophoresis-mass spectrometry parameters such as sheath liquid and sheath gas flow-rates, sheath liquid composition, electrospray voltage andthe CE capillary position were optimised. The MS and MS-MS spectra of positive ions were studied in order to obtain structural information for the confirmation of the identity. The use of labelled standards allowed to confirm fragment ions assignation. The detection limits, based on a signal-to-noise ratio of 3:1, were between 0.5 and 2.5 mg l(-1) with hydrodynamic injection (10 s) and between 1 and 10 microg l(-1) with elecrokinetic injection (20 s, 10 kV) using standards in ultrapure water. Quality parameters such as linearity and run-to-run precision (n=6) were established. Quantitation was carried out using labelled standards. The method has been applied to the analysis of contaminated irrigation water and spiked mineral water samples.     

Integrated pulsed amperometric detection of glufosinate, bialaphos and glyphosate at gold electrodes in anion-exchange chromatography.

A rapid and practical method for direct detection of the herbicides (glufosinate, bialaphos and glyphosate) in anion-exchange chromatography has been developed with integrated pulsed amperometric detection (IPAD). The electrochemical behavior of these herbicides showed catalytic currents based on the oxidation of amines in their structures. Waveform in IPAD was similar to that for amino acids, which exhibited adsorption/desorption catalytic features at gold electrode surface in alkaline solution. Under optimized conditions, detection limits (signal-to-noise ratio of 3) for glufosinate, bialaphos and glyphosate were 20, 65 and 50 ng ml(-1), respectively, with correlation coefficients of 0.995, 0.997 and 0.996 over concentration ranges of 0.1-45, 0.3-32 and 0.1-50 microg ml(-1), respectively. The relative standard deviations (n=5) were 1.7-3.0%. The present method was successfully applied to the determination of glyphosate in urine and serum.     

Carrier-mediated extraction of bipyridilium herbicides across the hydrophobic liquid membrane

Supported liquid membrane (SLM) method for preconcentration and enrichment of the two bipyridilium herbicides, namely diquat and paraquat, from environmental water samples has been developed. The permanently charged cationic herbicides were extracted from a flowing aqueous solution to a stagnant acidic acceptor solution across a liquid membrane containing 40% (v/v) di-(2-ethylhexyl) phosphoric acid dissolved in di-n-hexyl ether. The mass transfer of analytes is driven by the counter-coupled transport of hydrogen ions from the acceptor to the donor phase. The efficiency of the extraction process depends on the donor solution pH, the amount of the mobile carrier added to the liquid membrane and the concentration of the counter ion in the acceptor solution. The applicability of the method for extraction of these quaternary ammonium herbicides from environmental waters was also investigated by spiking analyte sample solutions in river water. With 24 h sample enrichment concentrations of diquat and paraquat down to ca. 10 ng/L could be detected in environmental waters.     

在线净化/固相萃取-高效液相色谱法测定饮用水和环境水体中的百草枯和敌草快

建立了在线净化/固相萃取(SPE)-高效液相色谱(HPLC)快速、准确测定饮用水和环境水体中的两种痕量除草剂百草枯和敌草快的方法。样品用大体积自动进样器注入在线净化小柱并流经固相萃取小柱,通过双梯度高效液相色谱系统中的上样泵实现净化和富集后,通过阀切换将固相萃取小柱切换至分析流路中;用分析泵将待测物从富集柱冲洗至分析柱进行测定。上样泵流速和分析泵流速分别为0.7和0.6 mL/min,采用等度洗脱方式完成两种除草剂的分离和检测。检测波长分别为260 nm (百草枯)和311 nm (敌草快),进样体积为2.5 mL,整个分析时间为16 min。该方法在1.0～20 μg/L范围内线性关系良好,两种除草剂的线性相关系数均大于0.9980,检出限分别为0.10和0.12 μg/L(S/N=3)。该方法前处理简单,快速,可用于饮用水和环境水体中痕量除草剂的测定。     

Simultaneous determination of the herbicides diquat and paraquat in water

A method based on solid-phase extraction (on silica cartridges) and high-performance liquid chromatography (HPLC) followed by diode array UV detection is presented as an analytical tool for screening diquat (DQ) and paraquat (PQ) in drinking waters. The method is useful for quality control laboratories of water companies and beverage industries. Absolute recoveries of DQ and PQ from drinking water (25 mL in all cases), spiked at levels between 0.1, 1.0, and 5.0 microg/L, range from 91% to 103%. Relative standard deviation percentages are between 3% and 11%. Quantitation and detection limits are 70 and 40 ng/L for DQ and 90 and 60 ng/L for PQ, respectively; therefore, these herbicides can be detected and quantitated at levels below the limits established by the European Union.     

Liquid chromatography-electrospray ionization isotope dilution mass spectrometry analysis of paraquat and diquat using conventional and multilayer solid-phase extraction cartridges

The performance of alkyl-silica sorbent packed solid-phase extraction (SPE) cartridges and a mixed-mode, polymeric sorbent packed SPE cartridge (resin SPE cartridge) were evaluated for the sample preparation of paraquat and diquat in environmental water and vegetation matrices. Also the recoveries of the native and 2H-labeled paraquat and diquat were correlated to validate that the 2H-labeled species can be used for the isotopic dilution mass spectrometry (IDMS) analysis of paraquat and diquat. The results show that the extraction efficiency of alkyl-silica SPE is dependent on the carbon loading of the sorbent and deteriorates with an increasing sample pH. The resin SPE cartridge required no pH adjustment and showed excellent correlation between the native and 2H-labeled species, therefore, allowing us to develop the first liquid chromatography-electrospray ionization IDMS analytical method for the analysis of paraquat and diquat in environmental water and vegetation matrices. Method detection limits derived using standard EPA protocol were 0.2 and 0.1 microg/l for paraquat and diquat in water matrices, and 0.02 and 0.01 microg/g in vegetation matrices, respectively.     

Ultra‐trace level determination of diquat and paraquat residues in surface and drinking water using ion‐pair liquid chromatography with tandem mass spectrometry: A comparison of direct injection and solid‐phase extraction methods

Direct injection and solid‐phase extraction methods for the determination of diquat and paraquat in surface and drinking water were developed using liquid chromatography with tandem mass spectrometry. The signal intensities of analytes based on six ion‐pairing reagents were compared with each other, and 12.5 mM nonafluoropentanoic acid was selected as the best suited amongst them. A clean‐up method was developed using Oasis hydrophilic–lipophilic balance; this was compared to the direct injection method, with respect to limits of detection, interference, precision, and accuracy. Limits of quantification of diquat and paraquat were 0.03 and 0.01 μg/L using the direct injection method, and 0.002 and 0.001 μg/L using the hydrophilic–lipophilic balance method. When the hydrophilic–lipophilic balance method was used to analyze target compounds in 114 surface water and 30 drinking water samples, paraquat and diquat were detected within a concentration range of 0.001–0.12 and 0.002–0.038 μg/L in surface water, respectively. When the direct injection method was used to analyze target compounds in the same samples, the detected concentrations of paraquat and diquat were within 25% in samples being >0.015 μg/L using the hydrophilic–lipophilic balance method. The liquid chromatography with tandem mass spectrometry method using direct injection can thus be used for routine monitoring of paraquat and diquat in surface and drinking water.     

Supercritical fluid extraction as an on-line clean-up technique for rapid amperometric screening and alternative liquid chromatography for confirmation of paraquat and diquat in olive oil samples

A rapid and simple method for the direct screening of paraquat (PQ) and diquat (DQ) in olive oil samples is proposed. The sample screening method involves supercritical fluid extraction (SFE) (clean-up followed by the extraction of the analytes) followed by continuous flow electrochemical detection. Those samples for which the total concentration is close to or above the threshold limit established by the Columbian Society for Social Protection (0.05mugg(-1)) are subsequently analyzed by liquid chromatography (LC) with diode array detection (DAD). This confirmation method allows the determination of PQ and DQ in the range between 0.04 and 1.0mugg(-1), with average relative standard deviations lower than 3.5%, and 0.003 and 0.002mugg(-1) detection limits for PQ and DQ, respectively. The proposed arrangement opens up interesting prospects for the direct determination of polar pesticides in complex samples with a good throughput and a high level of automation.     

Determination of triazine herbicides in environmental samples by dispersive liquid-liquid microextraction coupled with high performance liquid chromatography

A simple, rapid, efficient, and environmentally friendly method for the determination of five triazine herbicides in water and soil samples was developed by using dispersive liquid-liquid microextraction (DLLME), coupled with high performance liquid chromatography-diode array detection (HPLC-DAD). The water samples were directly used for DLLME extraction. For soil samples, the target analytes were first extracted by water-methanol (99:1, v/v). In the DLLME extraction method, chloroform was used as an extraction solvent, and acetonitrile as a dispersive solvent. Under the optimum conditions, the enrichment factors of DLLME were in the range between 183-221. The linearity of the method was obtained in the range of 0.5-200 ng/mL for the water sample analysis, and 1-200 ng/g for the soil samples, respectively. The correlation coefficients ranged from 0.9968 to 0.9999. The limits of detection were 0.05-0.1 ng/mL for the water samples, and 0.1-0.2 ng/g for the soil samples. The proposed method has been successfully applied to the analysis of target triazine herbicides (simazin, atrazine, prometon, ametryn, and prometryn) in water and soil samples with satisfactory results.     

Fast analysis of quaternary ammonium pesticides in food and beverages using cation‐exchange chromatography coupled with isotope‐dilution high‐resolution mass spectrometry

A fast separation based on cation‐exchange liquid chromatography coupled with high‐resolution mass spectrometry is proposed for simultaneous determination of chlormequat, difenzoquat, diquat, mepiquat and paraquat in several food and beverage commodities. Solid samples were extracted using a mixture of water/methanol/formic acid (69.6:30:0.4, v/v/v), while liquid samples were ten times diluted with the same solution. Separation was carried out on an experimental length‐modified IonPac CS17 column (2 × 15 mm²) that allowed the use of formic acid and acetonitrile as mobile phase. Detection limits for food and beverage matrices were established at 1.5 μg/L for chlormequat, difenzoquat and mepiquat, and 3 μg/L for diquat and paraquat, while for drinking water a pre‐analytical sample concentration allowed detection limits of 9 and 20 ng/L, respectively. Precision, as repeatability (RSD%), ranged from 0.2 to 24%, with a median value of 6%, and trueness, as recovery, ranged from 64 to 118%, with a median value of 96%. The method developed was successfully applied to investigate the presence of herbicide residues in commercial commodities (mineral water, orange juice, beer, tea, green coffee bean, toasted coffee powder, cocoa bean, white corn flour, rice and sugar samples).     

Photochemical-fluorimetric method for the determination of total chlorophenoxyacid herbicides

A room temperature photochemically-induced fluorescence (RTPF) method is proposed for the quantitative analysis of seven widely-used chlorophenoxyacid herbicides. The influence of organic solvent, pH (in aqueous solutions), methanol percentage, and UV irradiation time on the excitation and emission wavelengths and fluorescence intensity was investigated. It was found that the largest fluorescence signals were obtained in a mixture of methanol and pH 5 buffer (50/50, v/v), while organic solvents and water produced generally lower signals. The tri- and bichlorinated phenoxyacid herbicides were photolysed significantly more slowly than the monochlorinated derivatives, and the derivatives of 2-propionic acid were photodegraded more quickly than the corresponding derivatives of acetic and butyric acid. Selected UV irradiation times were found to be 15 min for all herbicides under study. Linear calibration graphs were established over about one to two orders of magnitude in the interval 0.1-10 mug ml(-1). The RTPF limits of detection were between 36 ng ml(-1) and 179 ng ml(-1), according to the compound. Analytical application of RTPF to river water samples containing chlorophenoxyacid herbicides is discussed.     

Determination of narciclasine in serum by reversed-phase high-performance liquid chromatography: comparison of amperometric, ultraviolet photometric and fluorescence detection

Narciclasine was determined in the blood of mice by reversed-phase high-performance liquid chromatography, using a C18 stationary phase and a mobile phase of methanol-0.025 M potassium dihydrogen phosphate (50:50, v/v) of pH 5.5. Amperometric detection at a carbon fibre array working electrode held at +1.8 V (Ag/AgCl) permitted determination down to concentrations of 10 and 15.4 ng ml-1 (at a signal-to-noise ratio of 2) in aqueous solution and in serum, respectively. Fluorescence detection (excitation and emission wavelengths of 360 and 480 nm, respectively) exhibited somewhat poorer sensitivities for aqueous and serum samples: the respective limits of detection were 25 and 32 ng ml-1 at a signal-to-noise ratio of 2. Both the amperometric and the fluorescence detection were free from interference from blood components, but the fluorescence measurement required a post-column pH adjustment. UV photometric detection at 254 nm exhibited detection limits of 15 and 65 ng ml-1 in aqueous samples and in serum, respectively, and suffered from interferences from blood components that strongly absorbed in the ultraviolet region. All three detection techniques exhibited good linearity and precision.     

Determination of paraquat and diquat in human body fluids by high-performance liquid chromatography/tandem mass spectrometry

Paraquat (PQ) and diquat (DQ) in human whole blood and urine were analyzed by high-performance liquid chromatography/tandem mass spectrometry (HPLC/MS/MS) with positive ion electrospray ionization (ESI). The compounds were extracted with Sep-Pak C18 cartridges from whole blood and urine samples containing ethyl paraquat as an internal standard. The separation of PQ and DQ was carried out using ion-pair chromatography with heptafluorobutyric acid in 20 mM ammonium acetate and acetonitrile gradient elution for successful coupling with MS. Both compounds formed base peaks due to [M-H]+ ions by HPLC/ESI-MS and the product ions produced from each [M-H]+ ion by HPLC/MS/MS. Selective reaction monitoring (SRM) showed much higher sensitivity for both body fluids. Therefore, a detailed procedure for the detection of compounds by SRM with HPLC/MS/MS was established and carefully validated. The recoveries of PQ and DQ were 80.8-95.4% for whole blood and 84.2-96.7% for urine. The calibration curves for PQ and DQ showed excellent linearity in the range of 25-400 ng ml(-1) of whole blood and urine. The detection limits were 10 ng ml(-1) for PQ and 5 ng ml(-1) for DQ in both body fluids. The intra- and inter-day precision for both compounds in whole blood and urine samples were not greater than 13.0%. The data obtained from the determination of PQ and DQ in rat blood after oral administration of the compounds are also presented.