New method to synthesize mesoporous titania by photodegradation of surfactant template

Mesoporous titania has been successfully synthesized by photodegradation removal of cetyltrimethylammonium bromide as the surfactant, after slow hydrolyzation of titanium(IV) isopropoxide. Fourier transform infrared spectra proved that photodegradation has successfully decreased the peak areas of the alkyl groups from the template. The nitrogen adsorption analysis showed that the pore size and the specific surface area of the mesoporous titania were 3.7 nm and 203 m² g⁻¹, respectively, proving the mesoporosity of the titania obtained with the existence of the interparticle mesoporosity which was confirmed by transmission electron microscopy. Based on X-ray diffraction results, the mesoporous titania obtained was in the form of crystalline anatase phase. Furthermore, results from the diffuse reflectance ultra violet-visible spectra showed that the composition of tetrahedral titanium(IV) was more than the octahedral titanium(IV). When the mesoporous titania obtained was used as a catalyst in the oxidation of styrene, an improvement in the conversion of styrene (38%) was observed when compared to those obtained using Degussa P25 TiO₂ (14%) as the catalyst.     

Adsorption and structural properties of channel-like and cage-like organosilicas

Channel-like and cage-like mesoporous silicas, SBA-15 (P6mm symmetry group) and SBA-16 (Im3m symmetry group), were modified by introducing single ureidopropyl surface groups, mixed ureidopropyl and mercaptopropyl surface groups, and single bis(propyl)disulfide bridging groups. These hexagonal and cubic organosilicas were prepared under acidic conditions via co-condensation of tetraethyl orthosilicate (TEOS) and proper organosilanes using poly(ethylene oxide)-block-poly(propylene oxide)-block-poly(ethylene oxide) amphiphilic block copolymer templates, P123 (EO₂₀PO₇₀EO₂₀) and F127 (EO₁₀₆PO₇₀EO₁₀₆). The modified SBA-15 and SBA-16 materials were synthesized by varying the molar ratio of organosilane to TEOS in the initial synthesis gel. The removal of polymeric templates, P123 and F127, was performed with ethanol/hydrochloric acid solution. In the case of SBA-15 the P123 template was fully extracted, whereas this extraction process was less efficient for the removal of F127 template from the SBA-16-type organosilicas; in the latter case a small residue of F127 was retained. The adsorption and structural properties of the resulting materials were studied by nitrogen adsorption-desorption isotherms at −196^∘C (surface area, pore size distribution, pore volumes), powder X-Ray diffraction, CHNS elemental analysis and high-resolution thermogravimetry. The structural ordering, the BET specific surface area, pore volume and pore size decreased for both channel-like and cage-like mesoporous organosilicas with increasing concentration of incorporated organic groups.     

Temporal evolution study of the plasma induced by CO2 pulsed laser on targets of titanium oxides

This paper reports studies on time-resolved laser induced breakdown spectroscopy (LIBS) of plasmas induced by IR nanosecond laser pulses on the titanium oxides TiO and TiO₂ (anatase). LIBS excitation was performed using a CO₂ laser. The laser-induced plasma was found strongly ionized yielding Ti⁺, O⁺, Ti^2 +, O^2 +, Ti^3 +, and Ti^4 + species and rich in neutral titanium and oxygen atoms. The temporal behavior of specific emission lines of Ti, Ti⁺, Ti^2 + and Ti^3 + was characterized. The results show a faster decay of Ti^3 + and Ti^2 + ionic species than that of Ti⁺ and neutral Ti atoms. Spectroscopic diagnostics were used to determine the time-resolved electron density and excitation temperatures. Laser irradiation of TiO₂-anatase induces on the surface sample the polymorphic transformation to TiO₂-rutile. The dependence on fluence and number of irradiation pulses of this transformation was studied by micro-Raman spectroscopy.     

Significant effect of lanthanide doping on the texture and properties of nanocrystalline mesoporous TiO2

A systematic study of microstructure and photocatalytic properties of lanthanide doping of nanocrystalline mesoporous titanium dioxide is performed. The anatase-to-rutile (A-R) phase transformation of nanosized TiO₂ was significantly inhibited by lanthanide doping and the inhibitory effect was enhanced with the increase of the rare earth radius, i.e., La³⁺>Gd³⁺>Yb³⁺ for different lanthanide dopants. At high calcination temperatures, different texture lanthanide titanium oxides of Ln₄Ti₉O₂₄ (La³⁺, Pr³⁺, Nd³⁺), Ln₂Ti₂O₇ (Eu³⁺, Gd³⁺, Tb³⁺, Dy³⁺, Er³⁺), and Yb₂TiO₅ were developed, respectively, revealing that the structures of lanthanide titanium oxide developed in Ln/TiO₂ depend on the lanthanide radius. Larger radius lanthanides prefer to form higher coordination number lanthanide titanium oxide. In addition, the thermal stability of mesoporous structures of TiO₂ was remarkable improved by lanthanide doping. The photocatalytic properties were studied by employing the photodegradation of Rhodamine B (RB) as a probe reaction. The results indicate that the lanthanide doping could bring about significant improvement to the photoreactivity of TiO₂, and the improvement was sensitive to the atomic electronic configuration.     

Rapid promoting thrombus formation and fibrin cross-linked Bi-doped mesoporous bioglass for hemostatic agent

Despite decades of development of biomaterials, hemorrhage remains a primary cause of death in surgeries and accidents. Effective hemostatic agents that induce hemostasis and rapid coagulation are needed by surgeons and in daily life. Here, we report on the application of hemostatic agents by studying mesoporous bioglass (MBG) doped with bismuth oxide via a two-step acid-catalyzed self-assembly (TSACSA) process. The results show that all the samples have an ordered mesoporous structure and a large surface area, especially MBG doped with 2 mol% Bi₂O₃ has the highest specific surface area (704.06 m²/g). MBG doped with different proportions of Bi accelerated the intrinsic coagulation pathway and was not found to exhibit severe erythrocyte cytotoxicity. It is worth noting that MBG added with 1 and 2 mol% Bi₂O₃ had higher thrombus formation, fibrin polymerization rates, and platelet adhesion; however, higher content of Bi₂O₃ (3 mol%) may affect the consequence of coagulation. These results of our investigation suggest that MBG doped with a low range of Bi is a potential hemostatic biomaterial for clinical applications.     

Ethylene glycol assisted preparation of Ti-modified polydopamine coated magnetic particles with rough surface for capture of phosphorylated proteins

The reversible protein phosphorylation is very important in regulating almost all aspects of cell life, while the enrichment of phosphorylated proteins still remains a technical challenge. In this work, polydopamine (PDA) modified magnetic particles with rough surface (rPDA@Fe₃O₄) were synthesized by introduction of ethylene glycol in aqueous solution. The PDA coating possessing a wealth of catechol hydroxyl groups could serve as an active medium to immobilize titanium ions through the metal-catechol chelation, which makes the fabrication of titanium ions modified rPDA@Fe₃O₄ particles (Ti⁴⁺-rPDA@Fe₃O₄) simple and very convenient. The spherical Ti⁴⁺-rPDA@Fe₃O₄ particles have a surface area of 37.7 m² g⁻¹ and superparamagnetism with a saturation magnetization value of 38.4 emu g⁻¹. The amount of Ti element in the particle was measured to be 3.93%. And the particles demonstrated good water dispersibility. The particles were used as adsorbents for capture of phosphorylated proteins and they demonstrated affinity and specificity for phosphorylated proteins due to the specific binding sites (Ti⁴⁺). Factors affecting the adsorption of phosphorylated proteins on Ti⁴⁺-rPDA@Fe₃O₄ particles were investigated. The adsorption capacity of Ti⁴⁺-rPDA@Fe₃O₄ particles for κ-casein was 1105.6 mg g⁻¹. Furthermore, the particles were successfully applied to isolate phosphorylated proteins in milk samples, which demonstrated that Ti⁴⁺-rPDA@Fe₃O₄ particles had potential application in selective separation of phosphorylated proteins.     

Highly ordered Ti-SBA-15: Efficient H2 adsorbent and photocatalyst for eco-toxic dye degradation

Highly ordered 2D-hexagonal mesoporous titanium silicate Ti-SBA-15 materials (space group p6mm) have been synthesized hydrothermally in acidic medium employing amphiphilic tri-block copolymer, Pluronic F127 as structure directing agent. Samples are characterized by powder X-ray diffraction, transmission electron microscopy, scanning electron microscopy, FT IR spectroscopy, UV-visible diffuse reflectance measurements, N₂ adsorption/desorption and TG-DTA analysis. XRD and TEM results suggested the presence of highly ordered mesophase with hexagonal pore arrangements. BET surface area for Ti-SBA-15 (924 m² g⁻¹) is considerably higher than the pure silica SBA-15 (611 m² g⁻¹) prepared following the same synthetic route. UV-visible and FT-IR studies suggested the incorporation of mostly tetrahedral titanium (IV) species, along with some six-coordinated sites in the silicate network. This material shows very good H₂ adsorption capacity at higher pressure and excellent catalytic activity in the photocatalytic degradation of ecologically abundant dye methylene blue.     

A strategy for scalable synthesis of Li4Ti5O12/reduced graphene oxide toward high rate lithium-ion batteries

Li₄Ti₅O₁₂/reduced graphene oxide (RGO) composites were prepared via a simple strategy. The as-prepared composites present Li₄Ti₅O₁₂ nanoparticles uniformly immobilized on the RGO sheets. The Li₄Ti₅O₁₂/RGO composites possess excellent electrochemical properties with good cycle stability and high specific capacities of 154 mAh g^− 1 (at 10C) and 149 mAh g^− 1 (at 20C), much higher than the results found in other literatures. The superior electrochemical performance of the Li₄Ti₅O₁₂/RGO composites is attributed to its unique hybrid structure of conductive graphene network with the uniformly dispersed Li₄Ti₅O₁₂ nanoparticles.     

Exfoliation and thermal transformations of Nb-substituted layered titanates

Single-layer Nb-substituted titanate nanosheets of ca. 1 nm thickness were obtained by exfoliating tetrabutylammonium (TBA)-intercalated Nb-substituted titanates in water. AFM images and turbidity measurements reveal that the exfoliated nanosheets crack and corrugate when sonicated. Upon heating, the thermal transformation into anatase and further to rutile is retarded. This suppression of the phase transition upon higher valent substitution may promote technological applications of anatase thin films, hereunder development of films with TCO properties. Depending on the oxygen partial pressure during the transformation, the Nb-substitution into TiO₂ provokes different defect situations and also electronic properties. At reducing conditions, Nb is incorporated as Nb^V and an equivalent amount of Ti^IV is transformed to Ti^III as evidenced by XPS. Magnetic susceptibility data show accordingly paramagnetic behavior. For samples heated in air Ti^IV and Nb^V cations prevail, the latter is compensated by cation vacancies. ⁹³Nb MAS NMR data prove that Nb is finely dispersed into the transformed (Ti,Nb)O₂ oxide matrices without sign of Nb₂O₅ (nano)precipitates. The Nb-O-Ti bonds and defects at cation sites are considered key factors for increasing the transformation temperatures for conversion of the nanosheets to anatase and finally into rutile. It is further tempting to link the delay in crystallization to morphology limitations originating from the nanosheets. The present work shows that layered Nb-titanates are appropriate precursors for formation of highly oriented Nb-substituted anatase thin films via delamination, reconstruction and subsequent heat treatment.     

Enhanced photocatalytic degradation of rhodamine B under visible light irradiation on mesoporous anatase TiO2 microspheres by codoping with W and N

Mesoporous anatase TiO₂ microspheres were prepared via solvothermal method. Ammonium tungstate was used as the W source, and ammonia gas flowing in an ammonothermal reactor as the N source for codoping. TiO₂:(W,N) mesoporous microspheres, which were prepared from solvothermal treatment at 160 °C for 16 h and thermal ammonolysis at 500 °C for 2 h after calcination, have high specific surface area of 106 m² g⁻¹. XPS results indicate the presence of N_O, N_i and W⁶⁺ in the codoped mesoporous TiO₂ microspheres. Monodoping with N shifts the absorption band edge of anatase TiO₂ from ultraviolet region to visible region. Although codoping with W makes the visible light absorbance decrease a little, the photocatalytic degradation of a cationic dye rhodamine B (RhB) on mesoporous TiO₂:(W,N) microspheres is increased to 1.7 times of that on mesoporous TiO₂:N microspheres. This may due to decreasing recombination centers by W-doping charge compensation.     

High-pressure synthesis and crystal structure of the mixed-valent titanium borate Ti5B12O26

The new titanium borate was synthesized under high-pressure/high-temperature conditions in a Walker-type multianvil apparatus at 7.5 GPa and 1350 °C. Ti₅B₁₂O₂₆ is built up exclusively from corner-sharing BO₄-tetrahedra and shows a structural relation to the Zintl phase NaTl. Consisting of B₁₂O₂₆-clusters as fundamental building blocks, the structure of Ti₅B₁₂O₂₆ can be described via two interpenetrating diamond structures as in NaTl, where each atom corresponds to one B₁₂O₂₆-cluster. The tetragonal titanium borate crystallizes with eight formula units in the space group I4₁/acd and exhibits lattice parameters of a=1121.1(2) pm and c=2211.5(4) pm. Ti₅B₁₂O₂₆ is a mixed-valent compound with Ti^III and Ti^IV cations. The environment of the titanium cations, as well as charge distribution calculations, leads us to the assumption that Ti^III and Ti^IV are located on different crystallographic sites.     

Li4Ti5O12/reduced graphite oxide nano-hybrid material for high rate lithium-ion batteries

A spinel Li₄Ti₅O₁₂ nanoplatelet/reduced graphite oxide nano-hybrid was successfully synthesized by a two-step microwave-assisted solvothermal reaction and heat treatment. The Li₄Ti₅O₁₂ in the hybrid could deliver a discharge capacity of 154 mAhg^? 1 of Li₄Ti₅O₁₂ at 1 C-rate, 128 mAhg^-1 of Li₄Ti₅O₁₂ at 50 C-rate and 101 mAhg^-1 of Li₄Ti₅O₁₂ at 100 C-rate. It demonstrated promising potential as an anode material in a Li-ion battery with excellent rate capability and good cycling.     

Synthesis,characterization and catalytic properties of heterogeneous iron(III) tetradentate Schiff base complexes for the aerobic epoxidation of styrene

A series of hybrid mesoporous SBA-15 materials containing four iron(III) Schiff base complexes of the type [FeL ^x (NO₃)] (x = 4–7, L = N,N′-bis(salicylidene)ethylenediamine, N,N′-bis(salicylidene)diethylenetriamine, N,N′-bis(salicylidene)o-phenylenediamine, N,N′-bis(3-nitro-salicylidene)ethylenediamine) was synthesized by a post-grafting route. The XRD, N₂ adsorption/desorption and TEM measurements confirmed the structural integrity of the mesoporous hosts, and the spectroscopic characterization techniques (FT-IR, UV–vis spectroscopy, ¹H NMR) confirmed the ligands and the successful anchoring of iron(III) Schiff base complexes over the modified mesoporous support. Quantification of the supported ligand and metal was carried out by TG/DSC and ICP-AES techniques. The catalyst FeL⁷-SBA resulting from N,N′-bis(3-nitro-salicylidene)ethylenediamine) ligand was considerably active for the aerobic epoxidation of styrene, in which the highest conversion of styrene reached 83.6%, and the selectivity to styrene oxide was 83.0%. Moreover, it was also found that the catalytic activity increases with the decrease in the electron-donating ability of the Schiff bases, and the selectivity varies according to the types of substituents in the ligands.     

Molecular Design Strategy for Ordered Mesoporous Stoichiometric Metal Oxide

A molecular design strategy is used to construct ordered mesoporous Ti³⁺‐doped Li₄Ti₅O₁₂ nanocrystal frameworks (OM‐Ti³⁺‐Li₄Ti₅O₁₂) by the stoichiometric cationic coordination assembly process. Ti⁴⁺/Li⁺‐citrate chelate is designed as a new molecular precursor, in which the citrate can not only stoichiometrically coordinate Ti⁴⁺ with Li⁺ homogeneously at the atomic scale, but also interact strongly with the PEO segments in the Pluronic F127. These features make the co‐assembly and crystallization process more controllable, thus benefiting for the formation of the ordered mesostructures. The resultant OM‐Ti³⁺‐Li₄Ti₅O₁₂ shows excellent rate (143 mAh g^?1 at 30 C) and cycling performances (<0.005 % fading per cycle). This work could open a facile avenue to constructing stoichiometric ordered mesoporous oxides or minerals with highly crystalline frameworks.     

Heterogenization of [Ti(η-C5HMe4)Cl3] on to MCM-41 and organomodified MCM-41 to form epoxidation catalyst

This paper describes the heterogenization of a tetramethylmonocyclopentadienyl titanium (IV) trichloride complex, [Ti(η⁵-C₅HMe₄)Cl₃] onto mesoporous MCM-41. Its immobilization has been performed via a straightforward grafting process of the organometallic precursor in the pores of an MCM-41 host material and by reaction with previously organomodified MCM-41 material with a hydroxyl triazine based compound. Applying all-silica MCM-41 hosts, stable and heterogeneous liquid-phase epoxidation catalysts are obtained. Powder X-ray diffraction and nitrogen adsorption-desorption analysis indicated that the structural integrity of the support has been preserved during the titanium complex immobilization. These materials have been also extensively characterized using diffuse reflectance UV-vis, ¹³C and ²⁸Si MAS NMR and FT-IR spectroscopy. With these techniques the strong adsorption of the intact catalytic complex within an all-silica MCM-41 host is demonstrated. These materials have been tested as catalyst for the epoxidation of aliphatic and aromatic alkenes with TBHP as oxidant exhibiting a significant selectivity toward the epoxide with negligible leaching of titanium species. The conversion values are moderated, being the olefin trend reactivity 1-octene > cyclohexene > styrene.     

Self-Assembly Approach Towards MoS2-Embedded Hierarchical Porous Carbons for Enhanced Electrocatalytic Hydrogen Evolution

Transition metal-based nanoparticle-embedded carbon materials have received increasing attention for constructing next-generation electrochemical catalysts for energy storage and conversion. However, designing hybrid carbon materials with controllable hierarchical micro/mesoporous structures, excellent dispersion of metal nanoparticles, and multiple heteroatom-doping remains challenging. Here, a novel pyridinium-containing ionic hypercrosslinked micellar frameworks (IHMFs) prepared from the core–shell unimicelle of s-poly(tert-butyl acrylate)-b-poly(4-bromomethyl) styrene (s-PtBA-b-PBMS) and linear poly(4-vinylpyridine) were used as self-sacrificial templates for confined growth of molybdenum disulfide (MoS₂) inside cationic IHMFs through electrostatic interaction. After pyrolysis, MoS₂-anchored nitrogen-doped porous carbons possessing tunable hierarchical micro/mesoporous structures and favorable distributions of MoS₂ nanoparticles exhibited excellent electrocatalytic activity for hydrogen evolution reaction as well as small Tafel slope of 66.7 mV dec⁻¹, low onset potential, and excellent cycling stability under acidic condition. Crucially, hierarchical micro/mesoporous structure and high surface area could boost their catalytic hydrogen evolution performance. This approach provides a novel route for preparation of micro/mesoporous hybrid carbon materials with confined transition metal nanoparticles for electrochemical energy conversion.     

High-Yield Synthesis of Gold Microplates Using Amphiphilic Block Copolymers: Are Lyotropic Liquid Crystals Required?

Summary : High-yield synthesis of gold microplates is achieved through autoreduction of hydrogen tetrachloroaureate (III) hydrate (HAuCl₄ · 3H₂O) in aqueous solutions of poly(ethylene oxide)-poly(propylene oxide)-poly(ethylene oxide) block copolymer (Pluronic L64, EO₁₃PO₃₀EO₁₃) at ambient conditions, in the absence of added energy, reductant, or other surfactants. The formation by the amphiphilic block copolymer of lyotropic liquid crystals (e.g., ordered cylindrical/hexagonal or lamellar phases) is not required for templating the formation of such microplates.     

Polymer-templated organosilicas with hexagonally ordered mesopores: the effect of organosilane addition at different synthesis stages

Two series of ordered mesoporous organosilica (OMO) SBA-15 materials with surface and bridging groups were fabricated by varying the organic precursor addition at different synthesis stages. The consequence of the delayed introduction of organic precursor on the structural and adsorption properties of the resulting OMOs was investigated. The OMOs studied were synthesized via co-condensation of tetraethyl orthosilicate (TEOS) and ureidopropyltrimethoxysilane (UPS) as well as TEOS and bis(triethoxysilylpropyl) disulfide (BTDS) in the presence of poly(ethylene oxide)-poly(propylene oxide)- poly(ethylene oxide) triblock copolymer Pluronic P123 (EO₂₀PO₇₀EO₂₀). The aforementioned OMOs were characterized by nitrogen adsorption-desorption isotherms at −196 °C and powder X-ray diffraction (XRD). Nitrogen adsorption isotherms were used to estimate the pore volume, mesopore diameter and the BET specific surface area, whereas the XRD data provided information about structural ordering and unit cell of the samples studied. Ryan Felix, undergraduate student from Oberlin College (Oberlin, OH, USA) participating in the NSF-REU program during Summer 2006.     

Different Reactivity of Rutile and Anatase TiO2 Nanoparticles: Synthesis and Surface States of Nanoparticles of Mixed-Valence Magnéli Oxides

Magnéli phases Ti_nO_2n−1 (3<n≤10) are mixed Ti⁴⁺/Ti³⁺ oxides with high electrical conductivity. When used for water remediation or electrochemical energy storage and conversion, they are nanostructured and exposed to various environments. Therefore, understanding their surface reactivity is of prime importance. Such studies have been hindered by carbon contamination from syntheses. Herein, this synthetic and characterization challenge is addressed through a new approach to 50 nm carbon-free Ti₄O₇ and Ti₆O₁₁ nanoparticles. It takes advantage of the different reactivities of rutile and anatase TiO₂ nanoparticles towards H₂, to use the former as precursor of Ti_nO_2n−1 and the latter as a diluting agent. This approach is combined with silica templating to restrain particle growth. The surface reactivity of the Magnéli nanoparticles under different atmospheres was then evaluated quantitatively by synchrotron-radiation-based X-ray photoelectron spectroscopy, which revealed oxidized surfaces with lower conductivity than the core. This finding sheds a new light on the charge transfer occurring in these materials.