Characterization of shock accelerometers using Davies bar and laser interferometer

In this paper, we propose a novel method for evaluating the frequency response of shock accelerometers using Davies bar and interferometry. The method adopts elastic wave pulses propagating in a thin circular bar for the generation of high accelerations. The accelerometer to be examined is attached to one end of the bar and experiences high accelerations of the order of 10³∼10⁵ m/s². A laser interferometer system is newly designed for the absolute measurement of the bar end motion. It can measure the motion of a diffuse surface specimen at a speed of 10⁻³ ∼10⁰ m/s. Uncertainty of the velocity measurement is estimated to be±6×10⁻⁴ m/s, proving a high potential for use in the primary calibration of shock accelerometers. Frequency characteristics of the accelerometer are determined by comparing the accelerometer's output with velocity data of the interferometry in the frequency domain. Two piezoelectric-type accelerometers are tested in the experiment, and their frequency characteristics are obtained over a wide frequency range up to several ten kilohertz. It is also shown that the results obtained using strain gages are consistent with those by this new method. Paper was presented at the 1992 SEM Spring Conference on Experimental Mechanics held in Las Vegas, NV on June 8–11.     

Irradiation-Induced Solute Clustering in a Low Nickel FeMnNi Ferritic Alloy

Understanding the radiation embrittlement of reactor pressure vessel (RPV) steels is required to be able to operate safely a nuclear power plant or to extend its lifetime. The mechanical properties degradation is partly due to the clustering of solute under irradiation. To gain knowledge about the clustering process, a Fe−1.1 Mn−0.7 Ni (at.%) alloy was irradiated in a test reactor at two fluxes of 0.15 and 9 ×10¹⁷ n _E > 1MeV .m^− 2.s^− 1 and at increasing doses from 0.18 to 1.3 ×10²⁴ n _E > 1MeV .m^− 2 at 300°C. Atom probe tomography (APT) experiments revealed that the irradiation promotes the formation in the α iron matrix of Mn/Mn and/or Ni/Ni pair correlations at low dose and Mn–Ni enriched clusters at high dose. These clusters dissolve partially after a thermal treatment at 400°C. Based on a comparison with thermodynamic calculations, we show that the solute clustering under irradiation can just result from an induced mechanism.     

Supersonic leeside flow topology on delta wings revisited

The leeside vortex structures on delta wings with sharp leading edges were studied for supersonic flow at the Institute of Theoretical and Applied Mechanics of the Russian Academy of Sciences in Novosibirsk. The experiments were carried out with three wings with sweep angles of χ=68°, 73°, and 78° and parabolic profiles in the 0.6 × 0.6 m² test section of the blow-down wind tunnel T-313 of the institute. The test conditions were varied from Mach numbers M=2 to 4, unit Reynolds numbers from Re _l=26 × 10⁶ to 56 × 10⁶ m⁻¹, and angles of attack from α=0° to 22°. The results of the investigations revealed that for certain flow conditions shocks are formed above, below, and between the primary vortices. The experimental data were accurate enough to detect the onset of secondary and tertiary separation as well as other boundaries. The various flow regimes discussed in the literature were extended in several cases. The major findings are reported. Received: 6 September 1999/Accepted: 24 January 2000     

Nusselt-Rayleigh correlations for free convection in 2D air-filled parallelogrammic enclosures with isothermal active walls

In the present study Nu-Ra-α correlations are proposed to calculate the steady-state natural convection heat transfer taking place in 2D air-filled cavities of parallelogrammic section. The thermal conditions and the dimensions of the enclosures permit to cover a large range of Rayleigh numbers, 1.7 × 10³  ≤ Ra ≤ 3.0 × 10⁹, suitable for diverse engineering applications. The two active walls of the cavities are kept vertical and isothermal at hot and cold temperatures T _h and T _c respectively. Separated by a horizontal distance H, they have the same height H and are connected by a closed adiabatic channel whose upper and lower walls can be inclined at an angle α with respect to the horizontal, varying between −60° to +60°. That gives rise to a conducting or insulating cavity, in the convective sense of the term (diode cavity). A computational model based on the finite volume method is used to solve the governing equations. The large number of treated configurations led to propose Nu-Ra-α correlations for large ranges of Ra and α which can be applied to many engineering areas. The results of this numerical study have been successfully compared with calculated and measured available data.     

Comparison of experimental data with results of some drying models for regularly shaped products

This paper presents an experimental and theoretical investigation of drying of moist slab, cylinder and spherical products to study dimensionless moisture content distributions and their comparisons. Experimental study includes the measurement of the moisture content distributions of slab and cylindrical carrot, slab and cylindrical pumpkin and spherical blueberry during drying at various temperatures (e.g., 30, 40, 50 and 60°C) at specific constant velocity (U = 1 m/s) and the relative humidity φ = 30%. In theoretical analysis, two moisture transfer models are used to determine drying process parameters (e.g., drying coefficient and lag factor) and moisture transfer parameters (e.g., moisture diffusivity and moisture transfer coefficient), and to calculate the dimensionless moisture content distributions. The calculated results are then compared with the experimental moisture data. A considerably high agreement is obtained between the calculations and experimental measurements for the cases considered. The effective diffusivity values were evaluated between 0.741 × 10⁻⁵ and 5.981 × 10⁻⁵ m²/h for slab products, 0.818 × 10⁻⁵ and 6.287 × 10⁻⁵ m²/h for cylindrical products and 1.213 × 10⁻⁷ and 7.589 × 10⁻⁷ m²/h spherical products using the Model-I and 0.316 × 10⁻⁵–5.072 × 10⁻⁵ m²/h for slab products, 0.580 × 10⁻⁵–9.587 × 10⁻⁵ m²/h for cylindrical products and 1.408 × 10⁻⁷–13.913 × 10⁻⁷ m²/h spherical products using the Model-II.     

Aerodynamic modification of flow over bluff objects by plasma actuation

Particle image velocimetry and smoke visualization are used to study the alteration of the flow field in the wake of a bluff body by use of an alternating current (AC) surface dielectric barrier discharge. Staggered, surface, and buried electrodes were positioned on the downstream side of circular cylinders at conditions of Re _D = 1 × 10⁴−4 × 10⁴ configured to impose a force due to the ion drift that is either along or counter to the free-stream flow direction. Smoke visualization and Particle Image Velocimetry (PIV) in the wake of the flow confirms that the configuration of the surface electrodes and operation of the discharge significantly alters the location of the flow separation point and the time-averaged velocity profiles in the near and distant wake. Measurements of the vibrational and the rotational temperature using optical emission spectroscopy on the N₂ second positive system (C³Π_u–B³Π_g) indicates that the resulting plasma is highly non-equilibrium and discounts the possibility of a thermal effect on the flow separation process. The mechanism responsible for reduction or enhancement of flow separation is attributed to the streamwise force generated by the asymmetric ion wind—the direction of which is established by the electrode geometry and the local surface charge accumulated on AC cycles.     

Modeling of water transport in roof tiles by removal of moisture at isothermal conditions

The main objective of this article is to describe the drying process of ceramic roof tiles, shaped from red clay, using diffusion models. Samples of the product with initial moisture content of 0.24 (db) were placed inside an oven in the temperatures of 55.6, 69.7, 82.7 and 98.6°C; and the data of the drying kinetics were obtained. The analytical solutions of the diffusion equation for the parallelepiped with boundary conditions of the first and third kinds were used to describe the drying processes. The process parameters were determined using an optimization algorithm based on inverse method coupled to the analytical solutions. The analysis of the results makes it possible to affirm that the boundary condition of the third kind satisfactorily describes the drying processes. The values obtained for the convective mass transfer coefficient were between 8.25 × 10⁻⁷ and 1.64 × 10⁻⁶ m s⁻¹, and for the effective water diffusivity were between 9.21 × 10⁻⁹ and 1.80 × 10⁻⁸ m² s⁻¹.     

Precursor ionization ahead of strong shock waves in argon

The mechanism of precursor ionization ahead of strong shock waves has been studied in a low density shock tube. The experimental results are illustrated with Arrhenius plots with kink points dividing them into two parts with apparent activation energy ratio 1:2, namely with the values 7.7 eV and 15.3 eV, and varying with first and third power of the density respectively. A model is proposed to interpret the facts where the process taking place in the precursor region, is a two step photo ionization accompanied with the drift flow effect of the gas relative to the shock wave or the ionization recombination effect according to whether the shock speed and initial density are low enough. The product of the A-A collision excitation cross section coefficientS ^* multiplied by the radiation cross sectionQ ^* of ArgonS ^*×Q ^*=1×10⁻³⁶ (cm⁴eV⁻¹) and the three body recombination coefficient of Argon at room temperaturek _ra =1×10⁻²⁴ (cm⁻⁶s⁻¹). The project supported by the National Natural Science Foundation of China     

Determination of dynamic yield strengths with embedded manganin gages in plate-impact and long-rod experiments

The dynamic yield strengths of three steels were determined at strain rates of about 10³ s⁻¹ and 10⁶ s⁻¹. The measurements at 10³ s⁻¹ were obtained by a new technique based on measurements of large amplitude elastic waves in long bars struck by rigid flyer plates. Embedded manganin gages were used to measure stress, and the gage records were long enough to observe subsequent reverberations between the bar free end and the plastically deformed impact end. The measurements at 10⁶ s⁻¹ were made with a slightly modified version of a conventional flyer-plate impact configuration. The data are combined with static results to show the behavior of these steels at strain rates of 10⁻³ s⁻¹ to 10⁶ s⁻¹.     

An optical dilatometer

Summary An instrument is described which enables displacements of 2 × 10⁻⁶ cm to be determined by means of interference phenomena of monochromatic light. The measuring pin is pushed against the specimen with a force of 4000 dynes. The instrument setting remains stable for a period of several hours.     

Dynamical deformation of a flat liquid–liquid interface

The passage of solid spheres through a liquid–liquid interface was experimentally investigated using a high-speed video and PIV (particle image velocimetry) system. Experiments were conducted in a square Plexiglas column of 0.1 m. The Newtonian Emkarox (HV45 50 and 65% wt) aqueous solutions were employed for the dense phase, while different silicone oils of different viscosity ranging from 10 to 100 mPa s were used as light phase. Experimental results quantitatively reveal the effect of the sphere’s size, interfacial tension and viscosity of both phases on the retaining time and the height of the liquid entrained behind the sphere. These data were combined with our previous results concerning the passage of a rising bubble through a liquid–liquid interface in order to propose a general relationship for the interface breakthrough for the wide range of Mo ₁/Mo ₂ ∈ [2 × 10⁻⁵–5 × 10⁴] and Re ₁/Re ₂ ∈ [2 × 10⁻³–5 × 10²].     

Quantitative Stereovision in a Scanning Electron Microscope

Accurate, 3D full-field measurements at the micron-level are of interest in a wide range of applications, including both facilitation of mechanical experiments at reduced length scales and accurate profiling of specimen surfaces. Scanning electron microscope systems (SEMs) are a natural platform for acquiring high magnification images for stereo-reconstruction. In this work, an integrated methodology for accurate three-dimensional metric reconstruction and deformation measurements using single column SEM imaging systems is described. In these studies, the specimen stage is rotated in order to obtain stereo views of the specimen as it undergoes mechanical or thermal loading. Simulations and preliminary experimental studies at 300× demonstrate that (a) spatially-varying image distortions can be removed from images using a non-parametric distortion model, (b) the system can be reliably calibrated using distortion-corrected images of a planar object and grid at various orientations and (c) specimen rotation variability during the measurement phase can be controlled so that baseline strain errors are within the range of ±150 με. Benchmark rigid body motion experiments using calibrated SEM views demonstrate that all components of strain in the reconstructed object have a mean value around O(10⁻⁴) and a random spatial distribution with standard deviation ≈ 300 micro-strain.     

Full-field Thermal Deformation Measurements in a Scanning Electron Microscope by 2D Digital Image Correlation

Using recently developed methods for application of a nano-scale random pattern having high contrast during SEM imaging, baseline full-field thermal deformation experiments have been performed successfully in an FEI Quanta SEM using 2D-DIC methods. Employing a specially redesigned commercial heating plate and control system, with modified specimen attachment procedures to minimize unwanted image motions, recently developed distortion correction procedures were shown to be effective in removing both drift and spatial distortion fields under thermal heating. 2D-DIC results from heating experiments up to 125°C on an aluminum specimen indicate that (a) the fully corrected displacement components have nearly random variability and a standard deviation of 0.02 pixels (≈25 nm at 200× and ≈0.5 nm at 10,000×) in each displacement component and (b) the unbiased measured strain fields have a standard deviation ≈150 × 10⁻⁶ and a mean value that is in good agreement with independent measurements, confirming that the SEM-DIC based method can be used for both micro-scale and nano-scale thermal strain measurements.

Shear Failure of Inconel 718 under Dynamic Loads

Kinetics of deformation and fracture of nickel–iron alloy Inconel 718 under dynamic shear loading was measured using a split torsional Hopkinson bar facility and high-speed photography. Tubular specimens with a reduced gage length and a starter notch were sheared at strain rates up to 6 × 10³ s⁻¹. High-speed photographs of fiducial lines scribed on the specimen surface showed the development of local strains and cracking. This paper describes the experimental and analytical procedures, illustrates average and local plastic strain evolution, and presents shear crack initiation times and propagation speeds.     

Single bubble deformation and breakup in simple shear flow

Experiments in a parallel band apparatus and a transparent concentric cylinder device allow the observation of bubble deformation (shape and orientation) and breakup as a function of the viscosity ratio λ and the Capillary number Ca. For viscosity ratios between 3.1 × 10⁻⁷ and 6.7 × 10⁻⁸, critical Capillary numbers Ca _c for bubble breakup between 29 and 45 are found. It is furthermore shown that in the given parameter space no clear distinction between tip breakup and fracture can be made for bubbles. An erratum to this article can be found at     

Precursor vacuum-ultraviolet radiation ahead of strong shock waves in a shock tube

The profile and excitation mechanism of vacuum-ultraviolet radiation emitted from shock wave is investigated in a shock tube. For shock wave in argon, the rdiation is due to resonant transition excited by argon-argon collision in the shock front with excitation cross section coefficientS ^*=1.0×10⁻¹⁷ cm²·ev⁻¹ and activation energyE ^*=11.4 ev. For shock wave in air the radition is emitted from a very thin shock layer in which the mechanism ofX ¹∑→b ¹∑ of N₂ is excited with excitation cross sectionQ=2×10⁻¹⁶cm² and activation energyE ^*=12.1 ev. Institute of Mechanics, Academia Sinica     

Direct Observation of Trapped Gas Bubbles by Capillarity in Sandy Porous Media

We investigated the mechanism of residual gas trapping at a microscopic level. We imaged trapped air bubbles in a Berea sandstone chip after spontaneous imbibition at atmospheric pressure. The pore structure and trapped bubbles were observed by microfocused X-ray computed tomography. Distributions of trapped bubbles in Berea and Tako sandstone were imaged in coreflooding at a capillary number of 1.0 × 10⁻⁶. Trapped bubbles are of two types, those occupying the center of the pore with a pore-scale size and others having a pore-network scale size. In low-porosity media such as sandstone, connected bubbles contribute greatly to trapped gas saturation. Effects of capillary number and injected water volume were investigated using a packed bed of glass beads 600μm in diameter, which had high porosity (38%). The trapped N₂ bubbles are stable against the water flow rate corresponding to a capillary number of 1.0 × 10⁻⁴.     

Experimental study on surface wave and film breakdown of falling liquid film flow

In order to evaluate characteristics of the liquid film flow and their influences on heat and mass transfer, measurements of the instantaneous film thickness using a capacitance method and observation of film breakdown are performed. Experimental results are reported in the paper. Experiments are carried out at Re = 250–10000, T _in = 20–50°C and three axial positions of vertically falling liquid films for film thickness measurements. Instantaneous surface waveshapes are given by the interpretation of the test data using the cubic spline method. The correlation of the mean film thickness versus the film Reynolds number is also given by fitting the test data. It is revealed that the surface wave has nonlinear behavior. Observation of film breakdown is performed at Re = 1.40 × 10³–1.75 × 10⁴ and T _in = 85–95°C. From experimental results, the correlation of the film breakdown criterion can be obtained as follows: Bd = 1.567 × 10⁻⁶ Re ^1.183     

Thin-layer drying of tomato (<Emphasis Type="Italic">Lycopersicum esculentum Mill. cv. Rio Grande</Emphasis>) slices in a convective hot air dryer

The effects of different drying temperatures on the drying kinetics of tomato slices were investigated using a cabinet-type dryer. The experimental drying data were fitted best to the to the Page and Modified Page models apart from other theoretical models to predict the drying kinetics. The effective moisture diffusivities varied from 1.015 × 10⁻⁹ to 2.650 × 10⁻⁹ m² s⁻¹over the temperature range studied, and activation energy was 22.981 kJ mol⁻¹.