Improvement of Ni/SDC anode by alkaline earth metal oxide addition for direct methane–solid oxide fuel cells

The anodic performances of Ni/CeO₂–Sm₂O₃(Ni/SDC) modified by the addition of alkaline earth metal oxides (MgO, CaO, and SrO) were investigated for direct oxidation of CH₄ in solid oxide fuel cells (SOFCs). Although the initial power density of cell with Ni/SDC anode modified by the addition of CaO was slightly lower than that of cell with Ni/SDC, the former anode exhibited an excellent stability compared to the latter one. Such a high stability of Ni–CaO/SDC anode may come from the inhibition of carbon deposition in addition to the retained ionic conductivity of anode.     

Electrochemical properties of polyaniline in p-toluene sulfonic acid solution

Polyaniline was deposited potentiodynamically on a stainless steel substrate in the presence of an inorganic acids (sulfuric acid). The electrochemical characterization of the electrode was carried out by means of cyclic voltammetry and electrochemical impedance spectroscopy in the organic acids (p-toluene sulfonic acid) solution. The results show that polyaniline has a high specific capacitance of 431.8 F g⁻¹ at 1 mV s⁻¹, high coulombic efficiency of 95.6% at 20 mV s⁻¹, and exhibits a high reversibility. This indicates the promising feasibility of the polyaniline used as an electrochemical capacitor material in the electrolyte of p-toluene sulfonic acid solution especially at high charge–discharge process.     

Effect of small amount of poly(ethylene naphthalate) on isothermal crystallization and spherulitic morphology of poly(trimethylene terephthalate)

The effect of a small amount of poly(ethylene naphthalate) (PEN) in its blends with poly(trimethylene terephthalate) (PTT) on isothermal melt-crystallization kinetics and spherulitic morphology of the blends was thoroughly investigated. The maximum PEN content in the blends was 9 wt%. Due to the single composition-dependent glass transition temperature (T_g) that was observed for each blend, these blends appeared to be miscible in the amorphous state. After isothermal crystallization from the melt state, the neat PTT and its blends with PEN exhibited either double or triple melting endotherms. The triple endothermic peaks were observed in both the neat PTT and the blends when being crystallized at crystallization temperatures (T_c) of less than or equal to 195 °C. The equilibrium melting temperature () for the neat PTT was determined based on the linear Hoffman–Weeks extrapolative method to be 248 °C. Such values for the blends were found to decrease with the addition and increasing amount of PEN. Both the neat PTT and the blends were isothermally crystallized over the T_c range of 190–205 °C. At a given T_c, the 97PTT/3PEN blend exhibited a half-time of crystallization (t_0.5) value that was lower, while it exhibited reciprocal half-time (), Avrami rate constant (K_A), and spherulitic growth rate (G) values that were greater, than those of the neat PTT. With further increase in the PEN content, the t_0.5 value increased, while the , K_A, and G values decreased. Analysis of the G values based on the Lauritzen–Hoffman's (LH) secondary nucleation theory showed that the neat PTT and the 91PTT/9PEN blend exhibited a regime II→III transition at 194 °C (467.2 K), while no regime transition was observed for the other two blends. The lateral and the fold surface free energies (σ and σ_e) and the work of chain folding (q) for the neat PTT and the blends were 19.4, 30.2–46.3 erg cm⁻², and 2.4–3.6 kcal mol⁻¹, respectively. Lastly, the effect of both the T_c and the PEN content on morphology and texture of the PTT spherulites was also investigated and the results showed that the texture of the spherulites became coarser with increasing T_c and PEN content.     

利用钐掺杂的氧化铈夹层提高燃料电池阳极的活性

考察了Ni-钐掺杂的氧化铈(Ni-SDC)复合阳极与La0.9Sr0.1Ga0.8Mg0.2O3(LSGM)电解质中间加入的SDC 中间层对阳极及整个电池性能的影响.结果表明，SDC中间层的加入显著减小了阳极极化过电位，但同时引入了欧姆降，降低了电池的功率输出密度.氢在Ni-SDC电极的氧化主要由两个过程控制，分别对应于交流阻抗谱的两个阻抗半圆，高频环随着SDC中间层的加入显著减小，可能对应于H2在Ni-SDC/SDC/H2三相界的电化学氧化或氧从LSGM向SDC的传输，低频环与SDC中间层无关，可能对应于氢在电极表面的解离吸附及吸附物种的扩散过程.使用Ni-SDC/SDC夹层阳极可以明显地提高电池的稳定性.     

Isoconversional kinetics of degradation of polyvinylpyrrolidone used as a matrix for ammonium nitrate stabilization

Thermogravimetric analyzer (TGA) has been applied to measure the kinetics of the thermal degradation of virgin polyvinylpyrrolidone (PVP) and a phase stabilized PVP–ammonium nitrate (AN) material. The PVP–AN samples have been prepared by using 20 wt.% of AN and PVP of three different molecular weights. Virgin PVP undergoes a major mass loss in the region 380–550 °C leaving a small amount of nonvolatile residue. The application of an advanced isoconversional method to the respective degradation process demonstrates that its effective activation energy increases from 70 kJ mol⁻¹ to a plateau value at 250–300 kJ mol⁻¹, which is independent of the molecular weight. The PVP–AN materials lose spontaneously 20% of their mass on heating above the glass transition temperature of the PVP matrix (160–180 °C). After the escape of AN, the remaining PVP matrix degrades in the same temperature region as virgin PVP, however, the effective activation energy of this degradation is 150–200 kJ mol⁻¹.     

Poly(arylene ether sulfone)s containing pendant sulfonic acid groups as membrane materials for direct methanol fuel cells

A series of poly(arylene ether sulfone)s containing pendant sulfonic acid groups have been prepared by an aromatic substitution polymerization reaction using 4,4-difluorodiphenylsulfone, 6,7-dihydroxy-2-naphthalenesulfonate, and various hydroxyl terminated monomers in the presence of potassium carbonate. The synthesized sulfonated polymers have been characterized by nuclear magnetic resonance spectroscopy, Fourier transform infrared spectroscopy, gel permeation chromatography, ion exchange capacity, thermogravimetric analysis, and proton conductivity measurements. With a molecular weight of 50,000–59,000 g/mol and an ion exchange capacity of 1.17 meq./g, these polymers are thermally stable up to 250 °C. They are found to exhibit better performance at 65 and 80 °C in direct methanol fuel cells than Nafion 115 membrane despite lower proton conductivity due to a significantly lower methanol crossover.     

Anode-supported planar SOFC with high performance and redox stability

Solid oxide fuel cells with full ceramic anodes have recently attracted increasing attention, because the conventional Ni/YSZ cermet anodes may fail during practical operation due to their weak mechanical stability in the case of re-oxidation of the nickel. However, until now the reported fuel cells based on ceramic anodes have been fabricated only as small pellet-sized cells and electrochemical performance has been barely satisfactory, making it difficult to evaluate these attempts with respect to commercial feasibility. Herein, we report single cells based on Y-substituted SrTiO₃ anode substrates. These planar cells have outer dimensions of 50 × 50 mm², which has not been reached for a ceramic anode-supported cell before. They show power densities of 0.7–1.0 W cm^? 2 at 0.7 V and 800 °C, which are sufficient for technical applications. The cells survived 200 anode-gas changes between fuel and air (redox cycles), providing a new direction for the development and commercialisation of anode-supported solid oxide fuel cells.     

利用钐掺杂氧化铈提高燃料电池阳极活性

用浸渍法制备并采用交流阻抗、极化等技术考察了不同组成的Ni-Sm3＋掺杂的CeO2(SDC) 复合镍阳极的电化学性能及相应电池的功率输出性能.结果表明，SDC掺入镍阳极后,阳极极化过电位及电池的欧姆电阻显著减小.其中阳极过电位的减小与SDC掺入镍电极引起的三相界扩展有关，但SDC的掺入同时引起了电极反应活化能的增加,造成低温下Ni-SDC的极化过电位大于纯Ni电极.高温下,Ni-SDC阳极的阻抗谱由两个半圆组成，其中高频半圆随着SDC掺入量的增加而减小,而低频环与SDC的掺入量基本无关.低温下只观察到一个高频环.高频环可能对应三相界反应,而低频环可能对应氢的解离吸附及扩散.75％（w）Ni-25％（w）SDC/La0.9Sr0.1Ga0.8Mg0.2O3(LSGM)/Sm0.5Sr0.5CoO3(SSC)在所研究的电池中具有最大功率输出密度，其值在1073、973、873 K下分别达到1.1、0.43、0.14 W•cm－2.     

Reduced N-methyl-pyridylethynyl porphyrins exhibit strong near-IR absorptions

Porphines bearing two N-methyl-4-pyridylethynyl substituent reversibly undergo two one-electron reductions at room temperature. The anion radicals and di-anions show diminished visible bands (450 nm and 600–700 nm) and intense absorptions in the 800-nm and 1100-nm region, respectively. Some of the near-IR bands have extinction coefficients greater than 1.5 × 10⁵ M⁻¹ cm⁻¹.     

Cellulose-precursor synthesis of nanocrystalline Ce<Subscript>0.8</Subscript>Gd<Subscript>0.2</Subscript>O<Subscript>2−δ</Subscript> for SOFC anodes

Developments of intermediate-temperature solid oxide fuel cells (IT SOFCs) require novel anode materials with a high electrochemical activity at 800–1070 K. The polarization of cermet anodes, made of nickel, ceria and yttria-stabilized zirconia (YSZ) and applied onto a YSZ solid electrolyte, can be significantly reduced by catalytically active ceria additions, the relative role of which increases with decreasing temperature. Further improvement is observed when using Ce_0.8Gd_0.2O_2– (CGO) having a high oxygen ionic conductivity instead of undoped ceria, owing to enlargement of the electrochemical reaction zone. Nanocrystalline CGO powders with grain sizes of 8–35 nm were thus synthesized via the cellulose-precursor technique and introduced into Ni–CGO–YSZ cermets, and tested in contact with a (La_0.9Sr_0.1)_0.98Ga_0.8Mg_0.2O_3– (LSGM) electrolyte at 873–1073 K. The results showed that the anode performance can be enhanced by additional surface activation, in particular by impregnation with a Ce-containing solution, and also by incorporation of YSZ, which probably acts as a cermet-stabilizing component. The overpotential of the surface-modified Ni–CGO (25 wt%–75 wt%) anode in a 10% H₂/90% N₂ atmosphere was approximately 110 mV at 1073 K with a current density of 200 mA/cm².Presented at the OSSEP Workshop Ionic and Mixed Conductors: Methods and Processes, Aveiro, Portugal, 10–12 April 2003     

High-pressure structural evolution of a perovskite solid solution (La1−x,Ndx)GaO3

The structural evolution with pressure of six perovskites in the system La_1−xNd_xGaO₃ with x=0.00, 0.06, 0.12, 0.20, 0.62 and 1.00 have been determined by single-crystal diffraction. At room pressure, all six samples have Pbnm symmetry. The room-pressure bulk moduli vary only slightly with composition, between K_0T=169(4) and 177(2) GPa, with . As pressure is increased there is significant compression of the octahedral Ga–O bonds, the tilts of the GaO₆ octahedra decrease and the structures evolve towards higher symmetry. At room conditions the average Ga–O bond length increases with increasing compositional parameter x. However, the GaO₆ become stiffer with increasing x; the Ga–O bonds thus become stiffer as they become longer. Bond strengths in the octahedra in perovskites are therefore not a simple function of bond lengths but depend also upon the extra-framework cation.Phase transitions to R-3c symmetry occur at 2.2 GPa in end-member LaGaO₃, at 5.5 GPa in the x=0.06 sample, at 7.8 GPa for x=0.12, and at 12 GPa for x=0.20. No evidence of the transition in the x=0.62 or 1.00 samples was found by X-ray diffraction to 9.4 or 8.0 GPa, respectively, or by Raman measurements of NdGaO₃ up to 16 GPa. The transition pressure therefore increases with increasing Nd content (increasing x) at approximately 0.45 GPa per 0.01 increment in x, at least up to x=0.20. Compression of the R-3c phase of LaGaO₃ above the transition results in no significant changes in the tilt angle of the octahedra. The structural behavior of all six samples at high pressures is the result of the GaO₆ octahedra being softer than the extra-framework (La, Nd)O₁₂ site. The results therefore demonstrate that the evolution of solid-solution perovskites at high pressures follow the same general principles recently elucidated for end-member compositions.     

Novel co-extruded electrolyte–anode hollow fibres for solid oxide fuel cells

Novel CGO/NiO–CGO dual-layer hollow fibres (HFs) have been fabricated in a single-step co-extrusion and co-sintering process. LSCF–CGO cathodes layers were then deposited onto the dual-layer HFs to construct micro-tubular SOFCs. The NiO in the micro-tubular HF–SOFCs was reduced at 550 °C using hydrogen gas to form Ni anodes. Scanning electron microscope images showed that the dual-layer HFs have porous anodes and dense electrolyte layers. Preliminary measurements with a HF–SOFC fed with H₂ and atmospheric oxygen, produced maximum power densities of 420 W m⁻² and 800 W m⁻² at 450 °C and 550 °C, respectively.     

Solvent effect on the blue shifted weakly H-bound F3 CH…FCD3 complex

Solvent effect on the ν^c frequency of CH stretching vibration of the blue shifted F₃CH…FCD₃ complex has been studied in liquefied N₂, CO, Ar, Kr and Xe. In the case of Xe, the spectroscopic measurements have also been extended to the solid state. It was found that the ν^c position of the complex in the solutions studied lowers with respect to the value in the gas phase. In liquid Xe, characterized by the largest permittivity, this effect reaches its maximum value of −14.5 cm⁻¹. The ν^c frequency begins to grow again just below the freezing point of Xe, where a noticeable (15%) increase of the density of Xe occurs. The experimental results obtained for the liquid phase have been analyzed in the framework of the Onsager-like reaction field model and Polarizable Continuum Model (PCM) implemented into a standard Gaussian 98 Program.     

Effects of additives on anodic fluorination in ionic liquid hydrogen fluoride salts

Anodic fluorination of ethyl α-(2-pyrimidylthio)acetate in neat ionic liquid hydrogen fluoride salts (Et₃N–3HF, Et₄NF–4HF, Et₄NF–5HF) was investigated to avoid an anode passivation, which sometimes occurs during anodic fluorination in organic solvent. In order to improve the yield of fluorinated product, polyether having coordination ability to cation and anodic stability was introduced to the reaction system as additives (3%). Furthermore, such additives were found to be also effective for anodic fluorodesulfurization of 4-phenylthio-1,3-dioxolan-2-one in neat ionic liquid system.     

Enhanced tungstate electrochromism via formation of transparent conductive networks

Indium tin oxide (ITO) nanopowder was added to a polymer film containing WO₃ · H₂O particles to enhance electron conductivity and complimentary Li ion kinetics in an electrochromic device. Film conductivity increased dramatically with ITO content, suggesting the formation of conductive ITO networks in the film. The improved electron conductivity leads to a substantial increase of the effective Li⁺ ion diffusion coefficient in the composite film, from 10⁻¹¹ to 10⁻⁹ cm²/s. Electrochromic contrast studies revealed that the presence of the ITO networks leads to enhanced blue/green color contrast.     

Phase behavior, microstructure transition, and antiradical activity of sucrose laurate/propylene glycol/the essential oil of Melaleuca alternifolia/water microemulsions

Nonionic sucrose ester microemulsions composed of sucrose laurate (SL), propylene glycol (PG) and water were prepared with the essential oil of Melaleuca alternifolia, commonly known as tea tree oil (TTO), as oil phase to investigate the phase behavior, microstructure, and antiradical activity. The pseudo-ternary phase diagrams were constructed to elucidate the phase behavior of the microemulsion formations at different weight ratios of surfactant and cosurfactant (S_m = SL/PG) of 1:1, 2:1, and 3:1. The extension of the microemulsion zone was found to be strongly dependent on the S_m ratios. The single phase microemulsion domain, especially o/w microemulsion region increased when S_m ratio is increased from 1:1 to 3:1 and no liquid crystalline structure was observed for all formulations studied. Microstructural aspects were studied by electrical conductivity and pulsed gradient spin echo (PGSE) NMR measurements along water titration line L28 (R_o = 2:8). The results from these combined techniques were in good agreement in regard to the microstructure transition points. The microstructural inversion of w/o to bicontinuous microemulsions occurred at 30 wt.% water while the transition from bicontinuous to o/w structure occurred at 55 wt.% water. The physical stability on storage temperature and time was examined by dynamic light scattering after the centrifuge test and freeze–thaw cycles. The droplet size was kept almost the same without any phase separation, providing less temperature-sensitivity up to 70 °C and good stability for 3 months at room temperature. The chemical profile and radical scavenging activity of TTO in o/w microemulsions was evaluated by means of gas chromatography–mass spectroscopy (GC–MS) and 2,2′-diphenyl-1-picrylhydrazyl free radical (DPPH) scavenging method, respectively. The major abundant constituents of crude TTO, monoterpene alcohols (terpinen-4-ol (41.65%), α-terpineol (3.18%)) and hydrocarbons (γ-terpinene (22.95%), α-terpinene (10.16%)) were identified and the composition percentage of each constituent was calculated form the GC peak areas by normalization method. The DPPH scavenging activity of TTO microemulsion was lower than pure TTO because the SL surfactant may obstruct the interaction between the TTO and DPPH, reducing the number of effective collisions.     

Electrochemical kinetics and cycling performance of nano Li[Li0.23Co0.3Mn0.47]O2 cathode material for lithium ion batteries

Li[Li_0.23Co_0.3Mn_0.47]O₂ cathode material was prepared by a sol–gel method. The material had a primary particle size of about 100 nm, covered by a 30 Å of Li₂CO₃ layer. The material showed promising electrochemical performance when cycled up to 3C rate. The electrochemical kinetics of the first charge was much slower than that of the second charge, due to the complex electrochemical process which involved not only Li⁺ diffusion but also release of oxygen. By taking account of this, the material was pre-charged very slowly (C/50) in the first cycle. This led to excellent electrochemical performance in the following cycles. For instance, the 1C-rate capacity increased to 168 mA h g⁻¹ after 50 cycles, comparing with the 145 mA h g⁻¹ obtained without pre-charging.     

Role of electrolytes in the preparation of nanoparticles via the emulsion polymerization of vinyl pivalate

By controlling both the kind of ion and the ionic strength of electrolytes in an emulsion polymerization system of vinyl pivalate containing about 1% sodium lauryl sulfate as a surfactant, nanoparticles of polyvinylpivalate having a diameter of about 25 nm were successfully prepared. The use of high concentrations of lithium chloride and lithium sulfate (1.0 mol L⁻¹) prevented the nanoparticles from aggregating and produced nanoparticles sizes of 25–50 nm. Ammonium acetate and sodium acetate, on the other hand, accelerated the aggregate of the nanoparticles. These phenomena were examined in detail and found to be similar to the Hofmeister phenomena and the combination rule proposed by Craig et al.     

Multiple-scattering approach to Sn L3-edge X-ray absorption near-edge structure (XANES) analyses for organic tin compounds

We apply multiple-scattering calculations to the analyses of Sn L₃-edge X-ray absorption near-edge structure (XANES) spectra for environmental organotin compounds such as SnCl_4−nMe_n, SnCl_4−nBt_n, and SnCl_4−nPh_n (n = 0–4) where Me = CH₃, Bt = C₄H₉, and Ph = C₆H₅. The XANES peak at 3960 eV has rich information on the local structure. Referring to the optimized structures by density functional theory (DFT) calculations, multiple-scattering calculations well explain the observed spectral changes for different “organic extents”. The present study also supports the widely-used semiempirical rule called ‘Natoli’s rule’ for these environmental compounds, which will be useful to use XANES spectra for the practical analytical tools.